56 Bauwesen
Refine
Document Type
- Doctoral Thesis (46) (remove)
Institute
- Institut für Strukturmechanik (ISM) (10)
- Professur Baubetrieb und Bauverfahren (7)
- F. A. Finger-Institut für Baustoffkunde (FIB) (6)
- Bauhaus-Institut für zukunftsweisende Infrastruktursysteme (b.is) (2)
- Professur Baumanagement und Bauwirtschaft (2)
- Professur Informatik in der Architektur (2)
- Professur Modellierung und Simulation - Konstruktion (2)
- Professur Stochastik und Optimierung (2)
- Graduiertenkolleg 1462 (1)
- Institut Geotechnik Weimar (1)
Keywords
- Beton (3)
- Concrete (3)
- Projektmanagement (3)
- BIM (2)
- Bauantrag (2)
- Baugenehmigung (2)
- Building application (2)
- Cement (2)
- Decision-making (2)
- Entscheidungsmodell (2)
In den letzten Jahrzehnten unterlag der Straßenbetriebsdienst tiefgreifenden Veränderungen. Diese Veränderungen schließt auch die betriebliche Steuerungsphilosophie ein, um eine planungsrationale und ökonomische Gestaltung des Straßenbetriebsdienstes zu unterstützen. Dabei erfolgt eine verbindliche Vorgabe der Leistungsinhalte und -umfänge und ermöglicht eine Budgetierung für das vorgesehene Jahresarbeitsprogramm.
Ziel der Untersuchung ist die Entwicklung eines Modells für die Ermittlung von leistungsbezogenen Musterjahresganglinien zur Unterstützung der Jahresarbeitsplanung. Dafür lagen für jede Leistung des Leistungsbereiches „Grünpflege“ jeweils 260 einzelne Jahresganglinien vor.
Im Ergebnis der Untersuchung wird die leistungsbezogene Musterjahresganglinie in vier Schritten ermittelt. Im ersten Schritt erfolgt die Prüfung der Datenqualität; im zweiten Schritt eine Korrelationsanalyse; im dritten Schritt die fachliche Überprüfung der Leistungsausprägung und im vierten Schritt die Ermittlung der leistungsbezogenen Musterjahresganglinie aus den verbliebenen leistungsbezogenen Jahresganglinien.
Der Entwurfsraum für den Entwurf eines Tragwerks ist ein n-dimensionaler Raum, der aus allen freien Parametern des Modells aufgespannt wird.
Traditionell werden nur wenige Punkte dieses Raumes durch eine numerische (computergestützte) Simulation evaluiert, meist auf Basis der Finite-Elemente-Methode.
Mehrere Faktoren führen dazu, dass heute oft viele Revisionen eines Simulationsmodells durchlaufen werden: Zum einen ergeben sich oft Planungsänderungen, zum anderen ist oft die Untersuchung von Planungsalternativen und die Suche nach einem Optimum wünschenswert.
In dieser Arbeit soll für ein vorhandenes Finite-Elemente-Framework die sequentielle Datei-Eingabeschnittstelle durch eine Netzwerkschnittstelle ersetzt werden, die den Erfordernissen einer interaktiven Arbeitsweise entspricht. So erlaubt die hier konzipierte Schnittstelle interaktive, inkrementelle Modelländerungen sowie Status- und Berechnungsergebnis-Abfragen durch eine bidirektionale Schnittstelle.
Die Kombination aus interaktiver numerischer Simulation und Interoperabilität durch die Anwendung von Konzepten zur Bauwerks-Informations-Modellierung im Tragwerksentwurf ist Ziel dieser Dissertation. Die Beschreibung der Konzeption und prototypischen Umsetzung ist Gegenstand der schriftlichen Arbeit.
The gradual digitization in the architecture, engineering, and construction industry over the past fifty years led to an extremely heterogeneous software environment, which today is embodied by the multitude of different digital tools and proprietary data formats used by the many specialists contributing to the design process in a construction project. Though these projects become increasingly complex, the demands on financial efficiency and the completion within a tight schedule grow at the same time. The digital collaboration of project partners has been identified as one key issue in successfully dealing with these challenges. Yet currently, the numerous software applications and their respective individual views on the design process severely impede that collaboration.
An approach to establish a unified basis for the digital collaboration, regardless of the existing software heterogeneity, is a comprehensive digital building model contributed to by all projects partners. This type of data management known as building information modeling (BIM) has many benefits, yet its adoption is associated with many difficulties and thus, proceeds only slowly. One aspect in the field of conflicting requirements on such a digital model is the cooperation of architects and structural engineers. Traditionally, these two disciplines use different abstractions of reality for their models that in consequence lead to incompatible digital representations thereof.
The onset of isogeometric analysis (IGA) promised to ease the discrepancy in design and analysis model representations. Yet, that initial focus quickly shifted towards using these methods as a more powerful basis for numerical simulations. Furthermore, the isogeometric representation alone is not capable of solving the model abstraction problem. It is thus the intention of this work to contribute to an improved digital collaboration of architects and engineers by exploring an integrated analysis approach on the basis of an unified digital model and solid geometry expressed by splines. In the course of this work, an analysis framework is developed that utilizes such models to automatically conduct numerical simulations commonly required in construction projects. In essence, this allows to retrieve structural analysis results from BIM models in a fast and simple manner, thereby facilitating rapid design iterations and profound design feedback.
The BIM implementation Industry Foundation Classes (IFC) is reviewed with regard to its capabilities of representing the unified model. The current IFC schema strongly supports the use of redundant model data, a major pitfall in digital collaboration. Additionally, it does not allow to describe the geometry by volumetric splines. As the pursued approach builds upon a unique model for both, architectural and structural design, and furthermore requires solid geometry, necessary schema modifications are suggested.
Structural entities are modeled by volumetric NURBS patches, each of which constitutes an individual subdomain that, with regard to the analysis, is incompatible with the remaining full model. The resulting consequences for numerical simulation are elaborated in this work. The individual subdomains have to be weakly coupled, for which the mortar method is used. Different approaches to discretize the interface traction fields are implemented and their respective impact on the analysis results is evaluated. All necessary coupling conditions are automatically derived from the related geometry model.
The weak coupling procedure leads to a linear system of equations in saddle point form, which, owed to the volumetric modeling, is large in size and, the associated coefficient matrix has, due to the use of higher degree basis functions, a high bandwidth. The peculiarities of the system require adapted solution methods that generally cause higher numerical costs than the standard procedures for symmetric, positive-definite systems do. Different methods to solve the specific system are investigated and an efficient parallel algorithm is finally proposed.
When the structural analysis model is derived from the unified model in the BIM data, it does in general initially not meet the requirements on the discretization that are necessary to obtain sufficiently accurate analysis results. The consequently necessary patch refinements must be controlled automatically to allowfor an entirely automatic analysis procedure. For that purpose, an empirical refinement scheme based on the geometrical and possibly mechanical properties of the specific entities is proposed. The level of refinement may be selectively manipulated by the structural engineer in charge. Furthermore, a Zienkiewicz-Zhu type error estimator is adapted for the use with isogeometric analysis results. It is shown that also this estimator can be used to steer an adaptive refinement procedure.
Although it is impractical to avert subsequent natural disasters, advances in simulation science and seismological studies make it possible to lessen the catastrophic damage. There currently exists in many urban areas a large number of structures, which are prone to damage by earthquakes. These were constructed without the guidance of a national seismic code, either before it existed or before it was enforced. For instance, in Istanbul, Turkey, as a high seismic area, around 90% of buildings are substandard, which can be generalized into other earthquakeprone regions in Turkey. The reliability of this building stock resulting from earthquake-induced collapse is currently uncertain. Nonetheless, it is also not feasible to perform a detailed seismic vulnerability analysis on each building as a solution to the scenario, as it will be too complicated and expensive. This indicates the necessity of a reliable, rapid, and computationally easy method for seismic vulnerability assessment, commonly known as Rapid Visual Screening (RVS). In RVS methodology, an observational survey of buildings is performed, and according to the data collected during the visual inspection, a structural score is calculated without performing any structural calculations to determine the expected damage of a building and whether the building needs detailed assessment. Although this method might save time and resources due to the subjective/qualitative judgments of experts who performed the inspection, the evaluation process is dominated by vagueness and uncertainties, where the vagueness can be handled adequately through the fuzzy set theory but do not cover all sort of uncertainties due to its crisp membership functions. In this study, a novel method of rapid visual hazard safety assessment of buildings against earthquake is introduced in which an interval type-2 fuzzy logic system (IT2FLS) is used to cover uncertainties. In addition, the proposed method provides the possibility to evaluate the earthquake risk of the building by considering factors related to the building importance and exposure. A smartphone app prototype of the method has been introduced. For validation of the proposed method, two case studies have been selected, and the result of the analysis presents the robust efficiency of the proposed method.
Die Arbeit leistet einen wissenschaftlichen Beitrag zur Erforschung der Einsatzmöglichkeiten eines Immobilienportfoliomanagements für öffentliche museale Schlösserverwaltungen in Deutschland. Insbesondere wird ein für deren Organisation spezifisches Modell zur Investitionssteuerung herausgearbeitet und dessen Anwendbarkeit in der Praxis mit Experten diskutiert.
Der Einsatz ungeeigneter Materialien ist eine der häufigsten Ursachen für Bauwerksschäden. Da die Beseitigung dieser Schäden oft mit hohen Kosten verbunden ist, besteht in der Baupraxis der Bedarf an einer Identifizierungsmethode für eingesetzte Baustoffe. Daneben wäre eine Kenntnis der in einem Bauwerk vorliegenden Materialien auch für Instandhaltungsarbeiten hilfreich.
Die Identifizierung der in einem Festbeton oder Festmörtel vorliegenden Zementart gilt auch gegenwärtig noch als schwierig oder sogar unmöglich. Die Schwierigkeiten ergeben sich in erste Linie daraus, dass die Hydratationsprodukte verschiedener Zementarten oft nur geringe Unterschiede in ihrer chemischen und mineralogischen Zusammensetzung aufweisen und die Hydratationsmechanismen bei einigen Zementarten noch nicht vollständig erforscht sind.
Primäres Ziel der vorliegenden Arbeit war es zu untersuchen, ob anhand des Mineralphasenbestandes, der sich während einer thermischen Behandlung von Zementsteinen einstellt, eine Identifizierung der vorliegenden Zementart möglich ist. Weiterhin sollte die Übertragbarkeit dieser Ergebnisse auf Betone und Mörtel eingeschätzt werden.
Zur Schaffung von Identifizierungsmerkmalen wurden die (angereicherten) Zementsteine bei Temperaturen im Bereich zwischen 600 °C und 1400 °C thermisch behandelt. An den getemperten Proben wurde der Mineralphasenbestand mittels Röntgendiffraktometrie bestimmt. Mit der gleichen Methode wurden die Ausgangszemente und die (angereicherten) Zementsteine untersucht. Aus der Gegenüberstellung der nachgewiesenen Mineralphasen konnten die gesuchten Identifizierungsmerkmale abgeleitet werden. Um den Einfluss der Gesteinskörnungen auf die Identifizierungsmöglichkeiten gesondert zu erfassen, wurde das Versuchsprogramm auf 3 Abstraktionsebenen angelegt. Für die Auswertung der Ergebnisse wurden die Proben zu Klassen zusammengefasst, welche jeweils charakteristische Zusammensetzungen der Ausgangszemente repräsentieren. Für die Analyseergebnisse wurden die klassenspezifischen die Mittel- und Grenzwerte bestimmt.
Als die effektivste Methode zur Anreicherung der Zementsteinmatrix aus Mörtel- und Betonproben erwies sich die Kombination aus einer Zerkleinerung in einem Laborbackenbrecher. Die fein partikulären Fraktionen, welche Zementsteingehalte von 70-80 Ma.-% aufwiesen, wurden als Analyseproben verwendet. Es zeigte sich aber auch, dass das Anreicherungsergebnis von der Gesteinskörnungsart abhängt. Bei Laborbetonen mit einer Kalkstein-Gesteinskörnung wurde mit der gleichen Methode lediglich eine Anreicherung des Zementsteins auf etwa 50 Ma.-% erreicht.
Die Untersuchungen auf Abstraktionsebene 1 lieferten die Erkenntnis, dass der Hydratationsprozess der Klinkerphasen, der Klinkerphasengemische sowie des Hüttensandes, auch in Gegenwart des Sulfatträgers für Behandlungstemperaturen im Bereich des Klinkerbrandes vollständig reversibel ist. Im Hinblick auf die Identifizierungsmöglichkeiten wurde 1100 °C als optimale Behandlungstemperatur ermittelt, da hier eine Schmelzphasenbildung ausgeschlossen werden kann.
Durch eine Gegenüberstellung der chemischen Zusammensetzung der Ausgangszemente und des Phasenbestandes nach der Temperung konnte nachgewiesen werden, dass bei reinen Zementsteinen grundsätzlich alle Bestandteile an der Reaktion, die während der thermischen Behandlung bei 1100 °C stattfindet, beteiligt sind. Der sich einstellende Phasen bestand ist nur von der chemischen Zusammensetzung der Probe und dabei besonders von derem CaO-Gehalt abhängig. Empirisch wurde eine Prioritätenfolge für die Phasenbildung ermittelt. Daraus geht hervor, dass bevorzugt CaO-reiche Phasen, wie Aluminatferritphase, Belit und Ye‘elimit entstehen und dass überschüssiger Kalk als freies CaO vorliegt. Nur wenn der CaO-Gehalt der Probe nicht für die vollständige Bildung der – in der Summe – kalkreichsten Phasen ausreicht, entstehen partiell oder vollständig kalkärmere Phasen, wie Merwinit und Melilith. Basierend auf den Prioritäten zur Phasenbildung wurde ein Satz von Berechnungsgleichungen aufgestellt, mit denen der CaO-Typ aus der Phasenzusammensetzung der bei 1100 °C getemperten Probe bestimmt werden kann. CaO-Typen repräsentieren Bereiche für die chemische Zusammensetzung der Ausgangsprobe, welche bei der Temperaturbehandlung zu einer charakteristischen qualitativen Phasenzusammensetzung führen. Die CaO-Typen der marktüblichen Zementarten wurden anhand der in der Norm EN 197 festgelegten Bereiche für die Zusammensetzung der Zemente aus ihren Hauptbestandteilen sowie der aus der Fachliteratur ermittelten Bereiche für die chemische Zusammensetzung dieser Hauptbestandteile ermittelt. Damit kann für die Zementarten der Phasenbestand vorhergesagt werden, welcher sich während der Temperaturbehandlung des entsprechenden Zementsteins einstellt. Ein Vergleich mit dem gemessenen Phasenbestand erlaubt so die Identifizierung der Zementart.
Die Übertragbarkeit der durch die Untersuchungen an den Zementsteinen gewonnenen Erkenntnisse und die daraus abgeleiteten Identifizierungsmöglichkeiten auf Zementsteine, welche aus quarzsandhaltigen Normmörteln angereichert wurden, konnte nachgewiesen werden. Dabei wurde eine leichte Verschiebung des Phasenbestandes hin zu kalkärmeren Phasen beobachtet, welche auf die Reaktionsbeteiligung eines Teils der in den Proben enthaltenen Restgesteinskörnung zurückzuführen ist. Die Unterscheidungsmöglichkeiten zwischen den Zementarten blieben jedoch überwiegend erhalten.
Bei Betonen nimmt der Einfluss der Gesteinskörnung auf den Phasenbestand deutlich zu und kann zum Teil nicht mehr vernachlässigt werden. Die Identifizierungsmöglichkeiten müssen deshalb nach der chemischen Zusammensetzung und der Reaktivität der Gesteinskörnung differenziert ermittelt werden. Dazu sind weitere Untersuchungen notwendig.
Für Zementsteine, zementsteinreiche Systeme sowie Mörtel und Betone mit wenig reaktiven Gesteinskörnungen kann die Zementart bereits mit der in dieser Arbeit vorgestellten Methode identifiziert werden. In Fällen, für die sich die Bereiche der chemischen Zusammensetzung mehrerer Zementarten überschneiden, kann es dabei notwendig sein, zusätzliche chemische bzw. mineralogische Untersuchungen durchzuführen, z. B. am unbehandelten Zementstein.
The thesis investigates at the computer aided simulation process for operational vibration analysis of complex coupled systems. As part of the internal methods project “Absolute Values” of the BMW Group, the thesis deals with the analysis of the structural dynamic interactions and excitation interactions. The overarching aim of the methods project is to predict the operational vibrations of engines.
Simulations are usually used to analyze technical aspects (e. g. operational vibrations, strength, ...) of single components in the industrial development. The boundary conditions of submodels are mostly based on experiences. So the interactions with neighboring components and systems are neglected. To get physically more realistic results but still efficient simulations, this work wants to support the engineer during the preprocessing phase by useful criteria.
At first suitable abstraction levels based on the existing literature are defined to identify structural dynamic interactions and excitation interactions of coupled systems. So it is possible to separate different effects of the coupled subsystems. On this basis, criteria are derived to assess the influence of interactions between the considered systems. These criteria can be used during the preprocessing phase and help the engineer to build up efficient models with respect to the interactions with neighboring systems. The method was developed by using several models with different complexity levels. Furthermore, the method is proved for the application in the industrial environment by using the example of a current combustion engine.
In recent years, substantial attention has been devoted to thermoelastic multifield problems and their numerical analysis. Thermoelasticity is one of the important categories of multifield problems which deals with the effect of mechanical and thermal disturbances on an elastic body. In other words, thermoelasticity encompasses the phenomena that describe the elastic and thermal behavior of solids and their interactions under thermo-mechanical loadings. Since providing an analytical solution for general coupled thermoelasticity problems is mathematically complicated, the development of alternative numerical solution techniques seems essential.
Due to the nature of numerical analysis methods, presence of error in results is inevitable, therefore in any numerical simulation, the main concern is the accuracy of the approximation. There are different error estimation (EE) methods to assess the overall quality of numerical approximation. In many real-life numerical simulations, not only the overall error, but also the local error or error in a particular quantity of interest is of main interest. The error estimation techniques which are developed to evaluate the error in the quantity of interest are known as “goal-oriented” error estimation (GOEE) methods.
This project, for the first time, investigates the classical a posteriori error estimation and goal-oriented a posteriori error estimation in 2D/3D thermoelasticity problems. Generally, the a posteriori error estimation techniques can be categorized into two major branches of recovery-based and residual-based error estimators. In this research, application of both recovery- and residual-based error estimators in thermoelasticity are studied. Moreover, in order to reduce the error in the quantity of interest efficiently and optimally in 2D and 3D thermoelastic problems, goal-oriented adaptive mesh refinement is performed.
As the first application category, the error estimation in classical Thermoelasticity (CTE) is investigated. In the first step, a rh-adaptive thermo-mechanical formulation based on goal-oriented error estimation is proposed.The developed goal-oriented error estimation relies on different stress recovery techniques, i.e., the superconvergent patch recovery (SPR), L2-projection patch recovery (L2-PR), and weighted superconvergent patch recovery (WSPR). Moreover, a new adaptive refinement strategy (ARS) is presented that minimizes the error in a quantity of interest and refines the discretization such that the error is equally distributed in the refined mesh. The method is validated by numerous numerical examples where an analytical solution or reference solution is available.
After investigating error estimation in classical thermoelasticity and evaluating the quality of presented error estimators, we extended the application of the developed goal-oriented error estimation and the associated adaptive refinement technique to the classical fully coupled dynamic thermoelasticity. In this part, we present an adaptive method for coupled dynamic thermoelasticity problems based on goal-oriented error estimation. We use dimensionless variables in the finite element formulation and for the time integration we employ the acceleration-based Newmark-_ method. In this part, the SPR, L2-PR, and WSPR recovery methods are exploited to estimate the error in the quantity of interest (QoI). By using
adaptive refinement in space, the error in the quantity of interest is minimized. Therefore, the discretization is refined such that the error is equally distributed in the refined mesh. We demonstrate the efficiency of this method by numerous numerical examples.
After studying the recovery-based error estimators, we investigated the residual-based error estimation in thermoelasticity. In the last part of this research, we present a 3D adaptive method for thermoelastic problems based on goal-oriented error estimation where the error is measured with respect to a pointwise quantity of interest. We developed a method for a posteriori error estimation and mesh adaptation based on dual weighted residual (DWR) method relying on the duality principles and consisting of an adjoint problem solution. Here, we consider the application of the derived estimator and mesh refinement to two-/three-dimensional (2D/3D) thermo-mechanical multifield problems. In this study, the goal is considered to be given by singular pointwise functions, such as the point value or point value derivative at a specific point of interest (PoI). An adaptive algorithm has been adopted to refine the mesh to minimize the goal in the quantity of interest.
The mesh adaptivity procedure based on the DWR method is performed by adaptive local h-refinement/coarsening with allowed hanging nodes. According to the proposed DWR method, the error contribution of each element is evaluated. In the refinement process, the contribution of each element to the goal error is considered as the mesh refinement criterion.
In this study, we substantiate the accuracy and performance of this method by several numerical examples with available analytical solutions. Here, 2D and 3D problems under thermo-mechanical loadings are considered as benchmark problems. To show how accurately the derived estimator captures the exact error in the evaluation of the pointwise quantity of interest, in all examples, considering the analytical solutions, the goal error effectivity index as a standard measure of the quality of an estimator is calculated. Moreover, in order to demonstrate the efficiency of the proposed method and show the optimal behavior of the employed refinement method, the results of different conventional error estimators and refinement techniques (e.g., global uniform refinement, Kelly, and weighted Kelly techniques) are used for comparison.
The detailed structural analysis of thin-walled circular pipe members often requires the use of a shell or solid-based finite element method. Although these methods provide a very good approximation of the deformations, they require a higher degree of discretization which causes high computational costs. On the other hand, the analysis of thin-walled circular pipe members based on classical beam theories is easy to implement and needs much less computation time, however, they are limited in their ability to approximate the deformations as they cannot consider the deformation of the cross-section.
This dissertation focuses on the study of the Generalized Beam Theory (GBT) which is both accurate and efficient in analyzing thin-walled members. This theory is based on the separation of variables in which the displacement field is expressed as a combination of predetermined deformation modes related to the cross-section, and unknown amplitude functions defined on the beam's longitudinal axis. Although the GBT was initially developed for long straight members, through the consideration of complementary deformation modes, which amend the null transverse and shear membrane strain assumptions of the classical GBT, problems involving short members, pipe bends, and geometrical nonlinearity can also be analyzed using GBT. In this dissertation, the GBT formulation for the analysis of these problems is developed and the application and capabilities of the method are illustrated using several numerical examples. Furthermore, the displacement and stress field results of these examples are verified using an equivalent refined shell-based finite element model.
The developed static and dynamic GBT formulations for curved thin-walled circular pipes are based on the linear kinematic description of the curved shell theory. In these formulations, the complex problem in pipe bends due to the strong coupling effect of the longitudinal bending, warping and the cross-sectional ovalization is handled precisely through the derivation of the coupling tensors between the considered GBT deformation modes. Similarly, the geometrically nonlinear GBT analysis is formulated for thin-walled circular pipes based on the nonlinear membrane kinematic equations. Here, the initial linear and quadratic stress and displacement tangent stiffness matrices are built using the third and fourth-order GBT deformation mode coupling tensors.
Longitudinally, the formulation of the coupled GBT element stiffness and mass matrices are presented using a beam-based finite element formulation. Furthermore, the formulated GBT elements are tested for shear and membrane locking problems and the limitations of the formulations regarding the membrane locking problem are discussed.
Für die Verminderung der betonspezifischen CO2-Emissionen wird ein verstärkter Einsatz klinkerreduzierter Zemente bzw. Betone angestrebt. Die Reduzierung des Klinkergehaltes darf jedoch nicht zu einer lebensdauerrelevanten Beeinträchtigung der Betondauerhaftigkeit führen. In diesem Zusammenhang stellt der Frost-Tausalz-Widerstand eine kritische Größe dar, da er bei höheren Klinkersubstitutionsraten häufig negativ beeinflusst wird. Erschwerend kommt hinzu, dass für klinkerreduzierte Betone nur ein unzureichender Erfahrungsschatz vorliegt. Ein hoher Frost-Tausalz-Widerstand kann daher nicht ausschließlich anhand deskriptiver Vorgaben gewährleistet werden. Demgemäß sollte perspektivisch auch für frost-tausalzbeanspruchte Bauteile eine performancebasierte Lebensdauerbetrachtung erfolgen.
Eine unverzichtbare Grundlage für das Erreichen dieser Ziele ist ein Verständnis für die Schadensvorgänge beim Frost-Tausalz-Angriff. Der Forschungsstand ist jedoch geprägt von widersprüchlichen Schadenstheorien. Somit wurde als Zielstellung für diese Arbeit abgeleitet, die existierenden Schadenstheorien unter Berücksichtigung des aktuellen Wissensstandes zu bewerten und mit eigenen Untersuchungen zu prüfen und einzuordnen. Die Sichtung des Forschungsstandes zeigte, dass nur zwei Theorien das Potential haben, den Frost-Tausalz-Angriff umfassend abzubilden – die Glue Spall Theorie und die Cryogenic Suction Theorie.
Die Glue Spall Theorie führt die Entstehung von Abwitterungen auf die mechanische Schädigung der Betonoberfläche durch eine anhaftende Eisschicht zurück. Dabei sollen nur bei moderaten Tausalzkonzentrationen in der einwirkenden Lösung kritische Spannungszustände in der Eisschicht auftreten, die eine Schädigung der Betonoberfläche hervorrufen können. In dieser Arbeit konnte jedoch nachgewiesen werden, dass starke Abwitterungen auch bei Tausalz¬konzentrationen auftreten, bei denen eine mechanische Schädigung des Betons durch das Eis auszuschließen ist. Damit wurde die fehlende Eignung der Glue Spall Theorie aufgezeigt.
Die Cryogenic Suction Theorie fußt auf den eutektischen Eigenschaften von Tausalz-lösungen, die im gefrorenen Zustand immer als Mischung auf festem Wassereis und flüssiger, hochkonzentrierter Salzlösung bestehen, solange ihre Eutektikumstemperatur nicht unter¬schritten wird. Die flüssige Phase im salzhaltigen Eis stellt für gefrorenen Beton ein bisher nicht berücksichtigtes Flüssigkeitsreservoir dar, welches trotz der hohen Salzkonzentration die Eisbildung in der Betonrandzone verstärken und so die Entstehung von Abwitterungen verursachen soll. In dieser Arbeit wurde bestätigt, dass die Eisbildung im Zementstein beim Gefrieren in hochkonzentrierter Tausalzlösung tatsächlich verstärkt wird. Das Ausmaß der zusätzlichen Eisbildung wurde dabei auch von der Fähigkeit des Zementsteins zur Bindung von Chloridionen aus der Tausalzlösung beeinflusst.
Zusammenfassend wurde festgestellt, dass die Cryogenic Suction Theorie eine gute Beschreibung des Frost-Tausalz-Angriffes darstellt, aber um weitere Aspekte ergänzt werden muss. Die Berücksichtigung der intensiven Sättigung von Beton durch den Prozess der Mikroeislinsenpumpe stellt hier die wichtigste Erweiterung dar. Basierend auf dieser Überlegung wurde eine kombinierte Schadenstheorie aufgestellt. Wichtige Annahmen dieser Theorie konnten experimentell bestätigt werden. Im Ergebnis wurde so die Grundlage für ein tiefergehendes Verständnis des Frost-Tausalz-Angriffes geschaffen. Zudem wurde ein neuer Ansatz identifiziert, um die (potentielle) Verringerung des Frost-Tausalz-Widerstandes klinkerreduzierter Betone zu erklären.