56.45 Baustoffkunde
Refine
Document Type
- Doctoral Thesis (20)
- Article (6)
- Conference Proceeding (2)
- Preprint (1)
Institute
- F. A. Finger-Institut für Baustoffkunde (FIB) (8)
- Professur Allgemeine Baustoffkunde (7)
- Professur Bauchemie und Polymere Werkstoffe (5)
- Professur Werkstoffe des Bauens (5)
- bauhaus.institut für experimentelle Architektur (2)
- Graduiertenkolleg 1462 (1)
- Institut für Strukturmechanik (ISM) (1)
- Professur Bauklimatik (1)
- Professur Bauphysik (1)
Keywords
- Beton (6)
- Mikrostruktur (6)
- Gips (5)
- Hydratation (5)
- Zement (4)
- Alkali-Kieselsäure-Reaktion (3)
- Mikroskopie (3)
- microstructure (3)
- Alkalisulfate (2)
- Betonzusatzmittel (2)
On the mechanisms of shrinkage reducing admixtures in self con-solidating mortars and concretes
(2010)
Self Consolidating Concrete – a dream has come true!(?) Self Consolidating Concrete (SCC) is mainly characterised by its special rheological properties. With-out any vibration this concrete can be placed and compacted under its own weight, without segrega-tion or bleeding. The use of such concrete can increase the productivity on construction sites and en-able the use of a higher degree of well distributed reinforcement for thin walled structural members. This new technology also reduces health risks since in contrast to the traditional handling of concrete, the emission of noise and vibration are substantially decreased. The specific mix design for self consolidating concretes was introduced around the 1980s in Japan. In comparison to normal vibrated concrete an increased paste volume enables a good distribution of aggregates within the paste matrix, minimising the influence of aggregates friction on the concrete flow property. The introduction of inert and/or pozzolanic additives as part of the paste provides the required excess paste volume without using disproportionally high amounts of plain cement. Due to further developments of concrete admixtures such as superplasticizers, the cement paste can gain self levelling properties without causing segregation of aggregates. Whereas SCC differs from normal vibrated concrete in its fresh attributes, it should reach similar properties in the hardened state. Due to the increased paste volume it usually shows higher shrinkage. Furthermore, owing to strength requirements, SCC is often produced at low water to cement ratios and hence may additionally suffer from autogenous shrinkage. This means that cracking caused by drying or autogenous shrinkage is a real risk for SCC and can compromise its durability as cracks may serve as ingression paths for gases and salts or might permit leaching. For the time being SCC still exhibits increased shrinkage and cracking probability and hence may be discarded in many practical applications. This can be overcome by a better understanding of those mechanisms and the ways to mitigate them. It is a target of this thesis to contribute to this. How to cope with increased shrinkage of SCC? In general, engineers are facing severe problems related to shrinkage and cracking. Even for normal and high performance concrete, containing moderate amounts of binder, a lot of effort was put on counteracting shrinkage and avoiding cracking. For the time being these efforts resulted in the knowledge of how to distribute cracks rather to avoid them. The most efficient way to decrease shrinkage turned out to be to decrease the cement content of concrete down to a minimum but still sufficient amount. For SCC this obviously seems to be contradictory with the requirement of a high paste volume. Indeed, the potential for shrinkage reduction is limited to some small range modifications in the mix design following two major concepts. The first one is the reduction of the required paste volume by optimising the aggregate grading curve. The second one involves high volume substitution of cement, preferentially using inert mineral additives. The optimization of grading curves is limited by several severe practical issues. Problems start with the availability of sufficiently fractionated aggregates. Usually attempts fail because of the enormous effort in composing application-optimized grading curves or mix designs. Due to durability reasons, the substitution rate for cement is limited depending on the application purpose and on environmental exposure of the hardened concrete. In the early 1980s Shrinkage Reducing Admixtures (SRA) were introduced to counteract drying shrinkage of concrete. The first publications explicitly dealing with SRA go back to Goto and Sato (Japan). They were published in 1983, which is also the time when the SCC concept was introduced. SRA modified concretes showed a substantial reduction of free drying shrinkage contributing to crack prevention or at least a significant decrease of crack width in situations of restrained drying shrinkage. Will shrinkage reducing admixtures contribute to a broader application of SCC? Within the last three decades performance tests on several types of concrete proved the efficiency of shrinkage reducing admixtures. So, at least in terms of shrinkage and cracking, concretes in general and SCC in particular can benefit from SRA application. But "One man's meat is another man's poison" and with respect to long term performance of SRA modified concretes there are still several issues to be clarified. One of these concerns the impact of SRAs on cement hydration. It is therefore an issue to know if changes in the hydrated phase composition, induced by SRA, result in undesired properties or decreased durability. Another issue is that the long term shrinkage reduction has to be evaluated. For example, one can wonder if SRA leaching may diminish or even eliminate long term shrinkage reduction and if the release of admixtures could be a severe environmental issue. It should also be noted that the basic mechanism or physical impact of SRA as well as its implementation in recent models for shrinkage of concrete is still being discussed. The present thesis tries to shed light on the role of SRA in self consolidating concrete focusing on the three questions outlined above: basic mechanisms of cement hydration, physical impact on shrinkage and the sustainability of SRA-application. Which contributions result from this study? Based on an extensive patent search, commercial SRAs could be identified to be synergistic mixtures of non-ionic surfactants and glycols. This turns out to be most important information for more than one reason and is the subject of chapter 4. An abundant literature focuses on properties of these non-ionic surfactants. Moreover, from this rich pool of information, the behaviour of SRAs and their interactions in cementitious systems were better understood through this thesis. For example, it could be anticipated how SRAs behave in strong electrolytes and how surface activity, i.e. surface tension, and interparticle forces might be affected. The synergy effect regarding enhanced performance induced by the presence of additional glycol in SRAs could be derived from the literature on the co-surfactant nature of glycols. Generally it now can be said that glycols ensure that the non-ionic surfactant is properly distributed onto the paste interfaces to efficiently reduce surface tension. In literature, the impact of organic matter on cement hydration was extensively studied for other admixtures like superplasticizer. From there, main impact factors related to the nature of these molecules could be identified. In addition, here again, the literature on non-ionic surfactants provides sufficient information to anticipate possible interactions of SRA with cement hydration based on the nature of non-ionic surfactants. All in all, the extensive study on the nature of non-ionic surfactants, presented in chapter 4, provides fundamental understanding of the behaviour of SRAs in cement paste. Taking a step further to relate this to the impact on drying and shrinkage required to review recent models for drying and shrinkage of cement paste as presented in chapter 3. There, it is shown that macroscopic thermodynamics of the open pore systems can be successfully applied to predict drying induced deformation, but that surface activity of SRA still has to be implemented to explain the shrinkage reduction it causes. Because of severe issues concerning the importance of capillary pressure on shrinkage, a new macroscopic thermodynamic model was derived in a way that meets requirements to properly incorporate surface activity of SRA. This is the subject of chapter 5. Based on theoretical considerations, in chapter 5 the broader impact of SRA on drying cementitious matter could be outlined. In a next step, cement paste was treated as a deformable, open drying pore system. Thereby, the drying phenomena of SRA modified mortars and concrete observed by other authors could be retrieved. This phenomenological consistency of the model constitutes an important contribution towards the understanding of SRA mechanisms. Another main contribution of this work came from introducing an artificial pore system, denominated the normcube. Using this model system, it could be shown how the evolution of interfacial area and its properties interact in presence of SRAs and how this impacts drying characteristics. In chapter 7, the surface activity of commercial SRAs in aqueous solution and synthetic pore solution was investigated. This shows how the electrolyte concentration of synthetic pore solution impacts the phase behaviour of SRA and conversely, how the presence of SRA impacts the aqueous electrolyte solution. Whilst electrolytes enhance self-aggregation of SRAs into micelles and liquid crystals, the presence of SRAs leads to precipitation of minerals as syngenite and mirabilite. Moreover, electrolyte solutions containing SRAs comprise limited miscibility or rather show miscibility gaps, where the liquid separates into isotropic micellar solutions and surfactant rich reverse micellar solutions. The investigation of surface activity and phase behaviour of SRA unravelled another important contribution. From macroscopic surface tension measurements, a relationship between excess surface concentration of SRA, bulk concentration of SRA and exposed interfacial area could be derived. Based on this, it is now possible to predict the actual surface tension of the pore fluid in the course of drying once the evolution of internal interfacial area is known. This is used later in this thesis to describe the specific drying and shrinkage behaviour of SRA modified pastes and mortars. Calorimetric studies on normal Portland cement and composite binders revealed that SRA alone show only minor impact on hydration kinetics. In presence of superplasticizer however the cement hydration can be significantly decelerated. The delaying impact of SRA could be related to a selective deceleration of silicate phase hydration. Moreover, it could be shown that portlandite precipitation in presence of SRA is changed, turning the compact habitus into more or less layered structures. Thereby, the specific surface increases, causing the amount of physically bound water to increase, which in turn reduces the maximum degree of hydration achievable for sealed systems. Extensive phase analysis shows that the hydrated phase composition of SRA modified binders re-mains almost unaffected. The appearance of a temporary mineral phase could be detected by environmental scanning electron microscopy. As could be shown for synthetic pore solutions, syngenite precipitates during early hydration stages and is later consumed in the course of aluminate hydration, i.e. when sulphates are depleted. Moreover, for some SRAs, the salting out phenomena supposed to be enhanced in strong electrolytes could also be shown to take place. The resulting organic precipitates could be identified by SEM-EDX in cement paste and by X-ray diffraction on solid residues of synthetic pore solution. The presence of SRAs could also be identified to impact microstructure of well cured cement paste. Based on nitrogen adsorption measurements and mercury intrusion porosimetry the amount of small pores is seen to increase with SRA dosage, whilst the overall porosity remains unchanged. The question regarding sustainability of SRA application is the subject of chapter 10. By means of leaching studies it could be shown that SRA can be leached significantly. The mechanism could be identified as a diffusion process and a range of effective diffusion coefficients could be estimated. Thereby, the leaching of SRA can now be estimated for real structural members. However, while the admixture can be leached to high extents in tank tests, the leaching rates in practical applications can be assumed to be low because of much reduced contact with water. This could be proven by quantifying admixture loss during long term drying and rewetting cycles. Despite a loss of admixture shrinkage reduction is hardly impacted. Moreover, the cyclic tests revealed that the total deformations in presence of SRA remain low due to a lower extent of irreversibly shrinkage deformations. Another important contribution towards the better understanding of the working mechanism of SRA for drying and shrinkage came from the same leaching tests. A significant fraction of SRA is found to be immobile and does not diffuse in leaching. This fraction of SRA is probably strongly associated to cement phases as the calcium-silicate-hydrates or portlandite. Based on these findings, it is now also possible to quantify the amount of admixture active at the interfaces. This means that, the evolution of surface tension in the course of drying can be approximated, which is a fundamental requirement for modeling shrinkage in presence of SRA. The last experimental chapter of this study focuses on the working mechanism and impact of SRA on drying and shrinkage. Based on the thermodynamics of the open deformable pore system introduced in chapter 5, energy balances are set up using desorption and shrinkage isotherms of actual samples. Information on distribution of SRA in the hydrated paste is used to estimate the actual surface tensions of the pore solution. In other words, this is the first time that the surface activity of the SRA in the course of the drying is fully accounted for. From the energy balances the evolution and properties of the internal interface are then obtained. This made it possible to explain why SRAs impact drying and shrinkage and in what specific range of relative humidity they are active. Summarising the findings of this thesis it can be said that the understanding of the impact of SRAs on hydration, drying and shrinkage was brought forward. Many of the new insights came from the careful investigation of the theory of non-ionic surfactants, something that the cement community had generally overlooked up to now.
Quantification of cracks in concrete thin sections considering current methods of image analysis
(2022)
Image analysis is used in this work to quantify cracks in concrete thin sections via modern image processing. Thin sections were impregnated with a yellow epoxy resin, to increase the contrast between voids and other phases of the concrete. By the means of different steps of pre-processing, machine learning and python scripts, cracks can be quantified in an area of up to 40 cm2. As a result, the crack area, lengths and widths were estimated automatically within a single workflow. Crack patterns caused by freeze-thaw damages were investigated. To compare the inner degradation of the investigated thin sections, the crack density was used. Cracks in the thin sections were measured manually in two different ways for validation of the automatic determined results. On the one hand, the presented work shows that the width of cracks can be determined pixelwise, thus providing the plot of a width distribution. On the other hand, the automatically measured crack length differs in comparison to the manually measured ones.
Research into bio-based epoxy resins has intensified in recent decades. Here, it is of great importance to use raw materials whose use does not compete with food production. In addition, the performance of the newly developed materials should be comparable to that of conventional products. Possible starting materials are lignin degradation products, such as vanillin and syringaldehyde, for which new synthesis routes to the desired products must be found and their properties determined. In this article, the first synthesis of two amine hardeners, starting with vanillin and syringaldehyde, using the Smiles rearrangement reaction is reported. The amine hardeners were mixed with bisphenol A diglycidyl ether, and the curing was compared to isophorone diamine, 4-4′-diaminodiphenyl sulfone, and 4-Aminonbenzylamine by means of differential scanning calorimetry. It was found that the two amines prepared are cold-curing. As TG-MS studies showed, the thermal stability of at least one of the polymers prepared with the potentially bio-based amines is comparable to that of the polymer prepared with isophorone diamine, and similar degradation products are formed during pyrolysis.
Bei der direkten thermische Umwandlung von Gips in Stuckgips entstehen texturierte Halbhydratkristallite von geringer Beständigkeit gegen hygro-mechnische Beanspruchung. Überlässt man diese texturierten Kristallite einer natürlichen Alterung, werden \"Heilungseffekte\" beobachtet, die durch lokale Umkristallisierungsreaktion an Oberflächendefekten erklärt werden können. Die gealterten Stuckgipse sind stabiler gegen hygro-mechanische Beanspruchungen. Durch Besprühung von Gips mit verdünnten wässrigen Salzlösungen vor der Calcivierung entsteht aridisierter Stuck geringer texturiert und damit stabiler gegen hygro-mechanische Beanspruchungen.
Der vorliegende Text beschreibt die intensive Erforschung von Wabenplatten aus Papierwerkstoffen, die durch Faltprozesse neue räumliche Zustände einnehmen können und somit ihr ursprüngliches Anwendungsspektrum erweitern. Die gezeigten Lösungsansätze bewegen sich dabei im Spannungsfeld von Architektur und Ingenieurbau, denn die gefalteten Bauteile sind nicht nur äußerst tragfähig sondern besitzen auch eine ästhetische Form. Die entwickelten Verfahren und Konstruktionen werden auf einem hohen architektonischen Niveau präsentiert und mit einfachen ingenieurtechnischen Methoden verifiziert. Zur Lösungsfindung werden geometrische Verfahren ebenso angewendet wie konstruktive Faustformeln und Recherchen aus Architektur und Forschung.
Der Fokus der Arbeit liegt auf der Untersuchung von Faltungen in Wabenplatten. Während der Auseinandersetzung mit der Thematik erschienen jedoch viele weitere Aspekte als sehr interessant und bearbeitungswürdig. Als theoretische Grundlage dieser Arbeit werden deshalb die geschichtliche Entwicklung und die gesellschaftliche Bedeutung von Papier und Papierwerkstoffen analysiert und deren Produktionsprozesse beleuchtet. Diese Vorgehensweise ermöglicht eine Einordnung des Potentials und der Bedeutung des Werkstoffs Papier. Der Kontext der Arbeit wird dadurch gestärkt und führt zu interessanten zukünftigen Forschungsansätzen.
Intensive Untersuchungen widmen sich der geometrischen Bestimmung von Faltungen in Wabenplatten aus Papierwerkstoffen sowie deren Manifestation als konstruktive Bauteile. Auch die statischen Eigenschaften der Elemente und ihr Konstruktionspotential werden erforscht und aufbereitet. Wichtige Impulse aus Forschung und Technik fließen in die Recherche der Arbeit ein und erlauben die Verortung der Ergebnisse im architektonischen Kontext. Versuchsreihen und Materialstudien an Prototypen belegen die Ergebnisse virtueller und rechnerischer Studien. Konzepte zur parametrischen Berechnung und Visualisierung der Forschungsergebnisse werden präsentiert und zeigen zukunftsfähige Planungshilfen für die Industrie auf. Etliche Testreihen zu unterschiedlichsten Abdichtungskonzepten führen zur Realisierung eines sehenswerten Experimentalbaus. Er erlaubt die dauerhafte Untersuchung der entwickelten Bauteile unter realistischen Bedingungen und bestätigt deren Leistungsfähigkeit. Dadurch wird nicht nur ein dauerhaftes Monitoring und eine Evaluierung der Leistungsdaten möglich sondern es wird auch der sichtbare Beweis erbracht, dass mit Papierwerkstoffen effiziente und hochwertige Architekturen zu realisieren sind, welche das enorme gestalterische Potential von gefalteten Wabenplatten ausnutzen.
The work has studied the structure and properties of gypsum compositions modified with the manmade modifier based on metallurgical dust and multi-walled carbon nanotubes. The results show that changing the structure of solid gypsum leads to the increase in bending and compressive strength by 70,5% and 138% correspondingly, the water resistance increasing and the softening factor reaching 0,85. Modifying gypsum composition with complex additive leads to the formation of amorphous structures based on calcium hydrosilicates on the surface of primary gypsum crystallohydrates that bond gypsum crystals and reduce the access of water.
Die Mahlung als Zerkleinerungsprozess stellt seit den Anfängen der Menschheit eine der wichtigsten Verarbeitungsformen von Materialien aller Art dar - von der Getreidemahlung, über das Aufschließen von Heilkräutern in Mörsern bis hin zur Herstellung von Tonern für Drucker und Kopierer. Besonders die Zementmahlung ist in modernen Gesellschaften sowohl ein wirtschaftlicher als auch ein ökologischer Faktor. Mehr als zwei Drittel der elektrischen Energie der Zementproduktion werden für Rohmehl- und Klinker- bzw. Kompositmaterialmahlung verbraucht. Dies ist nur ein Grund, warum der Mahlprozess zunehmend in den Fokus vieler Forschungs- und Entwicklungsvorhaben rückt. Die Komplexität der Zementmahlung steigt im zunehmenden Maße an. Die simple „Mahlung auf Zementfeinheit“ ist seit langem obsolet. Zemente werden maßgeschneidert, mit verschiedensten Kombinationsprodukten, getrennt oder gemeinsam, in unterschiedlichen Mahlaggregaten oder mit ganz neuen Ansätzen gefertigt. Darüber hinaus gewinnt auch der Sektor des Baustoffrecyclings, mit allen damit verbundenen Herausforderungen, immer mehr an Bedeutung. Bei der Fragestellung, wie der Mahlprozess einerseits leistungsfähige Produkte erzeugen kann und andererseits die zunehmenden Anforderungen an Nachhaltigkeit erfüllt, steht das Mahlaggregat im Mittelpunkt der Betrachtungen. Dementsprechend gliedert sich, neben einer eingehenden Literaturrecherche zum Wissensstand, die vorliegende Arbeit in zwei übergeordnete Teile:
Im ersten Teil werden Untersuchungen an konventionellen Mahlaggregaten mit in der Zementindustrie verwendeten Kernprodukten wie Portlandzementklinker, Kalkstein, Flugasche und Hüttensand angestellt. Um eine möglichst effektive Mahlung von Zement und Kompositmaterialien zu gewährleisten, ist es wichtig, die Auswirkung von Mühlenparametern zu kennen. Hierfür wurde eine umfangreiche Versuchsmatrix aufgestellt und
abgearbeitet. Das Spektrum der Analysemethoden war ebenfalls umfangreich und wurde sowohl auf die gemahlenen Materialien als auch auf die daraus hergestellten Zemente und Betone angewendet. Es konnte gezeigt werden, dass vor allem die Unterscheidung zwischen Mahlkörpermühlen und mahlkörperlosen Mühlen entscheidenden Einfluss auf die Granulometrie und somit auch auf die Zementperformance hat. Besonders stark wurden die Verarbeitungseigenschaften, insbesondere der Wasseranspruch und damit auch das Porengefüge und schließlich Druckfestigkeiten sowie Dauerhaftigkeitseigenschaften der aus diesen Zementen hergestellten Betone, beeinflusst. Bei Untersuchungen zur gemeinsamen Mahlung von Kalkstein und Klinker führten ungünstige Anreicherungseffekte des gut mahlbaren Kalksteins sowie tonigen Nebenbestandteilen zu einer schlechteren Performance in allen Zementprüfungen.
Der zweite Teil widmet sich der Hochenergiemahlung. Die dahinterstehende Technik wird seit Jahrzehnten in anderen Wirtschaftsbranchen, wie der Pharmazie, Biologie oder auch Lebensmittelindustrie angewendet und ist seit einiger Zeit auch in der Zementforschung anzutreffen. Beispielhaft seien hier die Planeten- und Rührwerkskugelmühle als Vertreter genannt. Neben grundlegenden Untersuchungen an Zementklinker
und konventionellen Kompositmaterialien wie Hüttensand und Kalkstein wurde auch die Haupt-Zementklinkerphase Alit untersucht. Die Hochenergiemahlung von konventionellen Kompositmaterialien generierte zusätzliche Reaktivität bei gleicher Granulometrie gegenüber der herkömmlichen Mahlung. Dies wurde vor allem bei per se reaktivem Zementklinker als auch bei latent-hydraulischem Hüttensand beobachtet. Gemahlene Flugaschen konnten nur im geringen Maße weiter aktiviert werden. Der generelle Einfluss von Oberflächenvergrößerung, Strukturdefekten und Relaxationseffekten eines Mahlproduktes wurden eingehend untersucht und gewichtet. Die Ergebnisse bei der Hochenergiemahlung von Alit zeigten, dass die durch Mahlung eingebrachten Strukturdefekte eine Erhöhung der Reaktivität zur Folge haben. Hierbei konnte festgestellt werden, das maßgeblich Oberflächendefekte, strukturelle (Volumen-)defekte und als Konterpart Selbstheilungseffekte die reaktivitätsbestimmenden Faktoren sind. Weiterhin wurden Versuche zur Mahlung von Altbetonbrechsand durchgeführt. Im Speziellen wurde untersucht, inwieweit eine Rückführung von Altbetonbrechsand, als unverwertbarer Teil des Betonbruchs, in Form eines Zement-Kompositmaterials in den Baustoffkreislauf möglich ist. Die hierfür verwendete Mahltechnik umfasst sowohl konventionelle Mühlen als auch Hochenergiemühlen. Es wurden Kompositzemente mit variiertem Recyclingmaterialanteil hergestellt und auf grundlegende Eigenschaften untersucht. Zur Bewertung der Produktqualität wurde der sogenannte „Aktivierungskoeffizient“ eingeführt. Es stellte sich heraus, dass die Rückführung von Altbetonbrechsand als potentielles Kompositmaterial wesentlich vom Anteil des Zementsteins abhängt. So konnte beispielsweise reiner Zementstein als aufgemahlenes Kompositmaterial eine bessere Performance gegenüber dem mit Gesteinskörnung beaufschlagtem Altbetonbrechsand ausweisen. Bezogen auf die gemessenen Hydratationswärmen und Druckfestigkeiten nahm der Aktivierungskoeffzient mit fallendem Abstraktionsgrad ab. Ebenfalls sank der Aktivierungskoeffizient mit steigendem Substitutionsgrad. Als Vergleich wurden dieselben Materialien in konventionellen Mühlen aufbereitet. Die hier erzielten Ergebnisse können teilweise der Hochenergiemahlung als gleichwertig beurteilt werden. Folglich ist bei der Aktivierung von Recyclingmaterialien weniger die Mahltechnik als der Anteil an aktivierbarem Zementstein ausschlaggebend.
Für die Sanierung von Bauwerken werden meist Informationen über die innere Struktur und den Aufbau, Belastungszustände, Feuchte- und Salzgehalte benötigt. Die Untersuchung mit zerstörungsarmen und -freien Methoden minimieren die dazu nötigen Eingriffe. Ebenfalls bieten die ZfP-Verfahren die Möglichkeit, den Erfolg einer Maßnahme zu kontrollieren sowie Prozesse über einen langen Zeitraum zu beobachten (Monitoring). Die vorliegende Arbeit befasst sich mit der zerstörungsfreien Untersuchung von inneren Strukturen und des Aufbaus von Mauerwerk mittels Ultraschall und Radar. Der untersuchte Querschnitt wird tomografisch rekonstruiert. Diese Darstellungsart bietet den Vorteil der Tiefenbestimmung von Objekten und der besseren Visualisierung für Auftraggeber und/oder Laien. Es wurden die Laufzeiten der Longitudinalwellen rekonstruiert. Die Frequenzen der Ultraschalluntersuchungen lagen bei 25 kHz sowie 85 kHz und der Radaruntersuchungen bei 900 MHz sowie 1,5 GHz. Die Rekonstruktion erfolgte mit dem Tomografieprogramm “Geo-Tom“, welches auf der Grundlage des SIRT-Algorithmus arbeitet. Die untersuchten Querschnitte beinhalteten Anomalien bestehend aus Luft, Granit, Holz und Mörtel. Die Abmaße der Anomalien lagen zwischen 10-27 cm bezogen auf einen Querschnitt von 0,76 x 1,0 m. Eine Ortung der Anomalien war möglich, wenn diese eine Laufzeitveränderung von mindestens der Größe des Messfehlers bewirken. Die Größe dieser Laufzeitdifferenz ist abhängig von den Abmaßen der Anomalie und dem Kontrast der elektromagnetischen bzw. akustischen Eigenschaften zwischen Anomalie und umgebenden Material. Eine Aussage über die Größe der Anomalie ist möglich, jedoch kann auf die Form nur bedingt geschlussfolgert werden. Des Weiteren kann durch den Vergleich der beiden Verfahren ein Rückschluss auf die möglichen Materialien der Anomalie gezogen werden.
Neben dem Schwerpunkt der Verflüssigung werden auch Zusatzmittel benötigt, die extrem lange Verarbeitbarkeitszeiten des Betons ermöglichen. Eine neue Wirkungsgruppe, durch die Verarbeitbarkeitszeiten von über 90 Stunden er-reicht werden können, sind Langzeitverzögerer (LVZ) auf der Basis von Phosphonsäure. In systematischen Versuchen wurden grundlegende Erkenntnisse über die Wirkungsmechanismen von LVZ auf die Hydratation gewonnen. Es hat sich gezeigt, dass die verzögernde Wirkung von LVZ auf die Bildung von schwer löslichem Calciumphosphonat zurückzuführen ist, welches die Partikeloberflächen žabdichtetœ. Vom Angebot an gelöstem Calcium hängt es ab, ob sich das žabdichtendeœ Calciumphosphonat direkt bildet oder ob durch den Calciumanspruch des LVZ eine kurzzeitig verstärkte Hydratation reaktiver Klin-kerphasen hervorgerufen wird. Sulfatoptimierte Zemente wiesen aufgrund der Anteile an Sulfatträger genüge! nd Calcium-Ionen für eine sofortige Bildung von Calciumphosphonat auf. In Verbindung mit der Bildung von primärem Ettringit bildet die Sulfatträgeroptimierung die Grundlage für die erwünschte Wirkungsweise des Zusatzmittels.