Refine
Document Type
- Conference Proceeding (336) (remove)
Institute
- Professur Informatik im Bauwesen (336) (remove)
Keywords
- Modellierung (49)
- Bauwerk (39)
- Verteiltes System (36)
- CAD (31)
- Finite-Elemente-Methode (24)
- Architektur (21)
- Computerunterstütztes Verfahren (21)
- Baubetrieb (17)
- Ingenieurbau (17)
- Internet (17)
In ersten Teil des Vortrages wird eine Heuristik zur Approximation der Pareto Menge multikriterielle verallgemeinerter Job-Shop Scheduling-Probleme vorgestellt. Der Algorithmus basiert auf einer genetischen lokale Suche Heuristik. Die Mittelwertbildung der Startzeiten der Vorgänge wurde hierbei als Rekombinationsoperator verwendet. Als lokale Suche wurde ein Threshold Accepting Algorithmus implementiert. Der Algorithmus wurde auf einer großen Menge von Benchmark-Instanzen und den Zielfunktionen Makespan, Tardiness, Lateness und Summe der Fertigstellungszeiten getestet. Die Ergebnisse zu den verschiedenen Zielfunktionen werden vorgestellt. Die vom Algorithmus erzeugte Approximation der Pareto Menge kann eine große Anzahl von Lösungen enthalten. Aus dieser Menge muss der Entscheidungsträger eine Lösung auswählen. Da die Datenmenge schon bei moderaten Problemdimensionen sehr umfangreich wird, stellt dies ein Problem für den Entscheider dar. Deshalb muss die große Menge der Lösungen auf eine überschaubare Anzahl reduziert werden. Bei dieser Reduktion der Lösungen muss die Diversität der verbleibenden Lösungen beachtet werden. Diese Reduzierung wird als Short Listing bezeichnet und im zweiten Teil des Vortrages vorgestellt. Im ersten Schritt des Short Listings werden die Lösungen mittels Abstandsmaßen im Lösungsraum geclustert. Die dazu verwendeten Abstandsmaße werden auf den Permutationen der Vorgänge auf den Ressourcen definiert. Es wurden fünf Abstandsmaße und zwei Clusterverfahren, ein hierarchisches und ein nicht-hierarchisches, untersucht. Im zweiten Schritt wird aus jedem Cluster jeweils eine Lösung ausgewählt und dem Entscheidungsträger vorgelegt. Dabei wurden zwei Methoden untersucht. Im ersten Fall wurde die bezüglich einer Ranking-Funktion beste Lösung und im zweiten Fall die Medianlösung bezüglich des Abstandsmaßes ausgewählt. Die Abstandsmaße, Clusteralgorithmen und Auswahlmethoden wurden auf einer großen Menge von Benchmark-Instanzen verglichen. Die Ergebnisse werden im Vortrag vorgestellt.
Für planende Ingenieure und Architekten besteht seit jeher im Rekonstruktionsbereich die Aufgabe, vorhandene Gebäude in ihrer Geometrie und Struktur zu erfassen und daraus Rekonstruktionspläne und -technologien zu erarbeiten. Diese Erfassungsmaßnahmen sind sehr umfangreich und kostenintensiv. Ziel der hier vorzustellenden Ansatzes war es deshalb, ein kostengünstiges Verfahren zu entwickeln, das ein berührungsloses Aufmaß eben begrenzter Räume (polyedrischer Räume) mit einer den Erfordernissen entsprechenden Genauigkeit gewährleistet. Es werden im wesentlichen zwei Problemkreise behandelt. Der erste beinhaltet den Nachweis einer für die geplanten Anwendungen hinreichend genauen, maßstäblichen Rekonstruierbarkeit von ebenen Objekten (Wänden) aus monokularen Fotoaufnahmen. Anstelle des in der Photogrammetrie üblichen Weges über Kamerakalibrierung mittels exakt eingemessener Paßpunkte wurde ein Ansatz verfolgt, bei dem eine mittels Laserspotprojektoren auf dem Aufnahmeobjekt erzeugte parameterabhängige Maßfigur in Verbindung mit a priori bekannten Bildinhalten Grundlage für die maßstabsgerechte Rekonstruktion des Objektes ist. Der zweite Problemkreis behandelt die Zusammensetzung von eben begrenzten Räumen aus Einzelebenen (Wänden) die als Ergebnis des ersten Schrittes projektiv entzerrt, d.h. als orthogonale Draufsicht, allerdings verfahrensbedingt fehlerbehaftet vorliegen. Ziel ist hier, durch Nutzung von a-priori-Kenntnissen über die Raumstruktur mit Hilfe von Methoden der mathematischen Optimierung einen Genauigkeitsgewinn zu erzielen.
Die Einführung von neuen Informations- und Kommunikationstechniken in Klein- und Mittelständische Unternehmen (hier: kleine und mittlere Planungsbüros im Bauwesen) ist mit speziellen Problemen behaftet. Erfahrungswerte liegen nur in größeren und zumeist fachfremden Firmen vor. Neben den eigentlichen Sicherheitsrisiken (Thematik Internet), Verständnisschwierigkeiten und daraus resultierenden Akzeptanzproblemen fehlt beim Einsatz dieser neuen Techniken die Verbindung zum Ablauf in projektbasiert arbeitenden Unternehmen. Der Begeisterung und Euphorie durch den Einsatz neuer Technik stehen Änderungen des eigenen Arbeitsstiles und ein anfänglicher Mehraufwand entgegen. Ein Schwerpunktthema der eigenen Forschungsarbeiten sind die Ermittlung und Validierung von Kriterien für die Einführung neuer IuK-Techniken speziell in kleineren und mittleren Planungsbüros. In einer fortschreitenden Reihe von Arbeiten am Fachbereich wurden und werden nacheinander die genannten Problematiken und Aspekte in Angriff genommen. Dabei werden neben der Kategorisierung von Anwendungsszenarien und Vorstellung der einzelnen, empfehlenswerten Techniken einzelne Konzepte am Fachbereich und in Zusammenarbeit mit Ingenieurbüros überprüft. Der Beitrag möchte in Ergänzung zu bereits gelaufenen Arbeiten als Empfehlung oder Leitfaden für Planungsbüros auf die Machbarkeit neuer Techniken und einige nötige Randbedingungen eingehen.
Usually, the co-ordination of design and planning tasks of a project in the construction industries is done in a paper based way. Subsequent modifications have to be handled manually. The effects of modifications cannot be determined automatically. The approach to specify a complete process model before project start does not consider the requirements of the construction industries. The effort of specification at the beginning and during the process (modifications) does not justify the use of standard process model techniques. A new approach is presented in the according paper. A complete process model is deducted on the basis of a core. The core consists of process elements and specific relations between them. Modifications need to be specified in the core only. The effort of specification is therefore reduced. The deduction of the complete process is based on the graph theory. Algorithms of the graph theory are also used to determine the effects of modifications during project work.
Der Fokus des Projektes liegt auf einer besseren Unterstützung der kooperativen Aspekte im Bauwerksentwurf und der Anwendung von ComponentWare-Techniken in der Architektur des Entwurfssystems. Es muß festgestellt werden, daß die Kooperation der Beteiligten im Entwurfsprozeß von Bauwerken durch die heute praktizierten Datenaustauschverfahren nicht oder nur unbefriedigend unterstützt wird und das keine Lösung dieses Problems durch die Weiterentwicklung von filebasierten Datenaustauschformaten zu erwarten ist. Im Rahmen des Projektes wird mit einer CORBA-Umgebung für Smalltalk-80 ein verteilbares Objektsystem realisiert. Als Architektur des Systems wurde eine hybride Herangehensweise gewählt, bei der allgemeine Informationen auf einem zentralen Server verwaltet werden und die eigentlichen Projektinformationen bei Bedarf repliziert werden. Wie allgemein in GroupWare - orientierten Systemen notwendig, müssen effektive Mechanismen der Nebenläufigkeitskontrolle und zur Sperrung bestimmter Modellbereiche realisiert werden. Wichtig ist für kooperative Entwurfssysteme die Systemunterstützung der Beseitigung der Folgen von kollidierenden Entwurfsintensionen durch die Bearbeiter. Dazu werden unter anderem Remote-Pointer-Mechanismen realisiert. In Abhängigkeit von der Rolle eines Bearbeiters werden diesem Sichten auf des Objektmodell (Partialmodelle) zugeordnet. Es werden Mechanismen zur Autorisierung des Zugriffs auf Partialmodelle implementiert, zu diesem Zweck erfolgt eine Nutzerauthentifizierung. Beziehungen zwischen Partialmodellen werden durch eine spezielle Relation im Objektsystem abgebildet. Die Konzeption des Objektsystems lehnt sich an die PREPLAN-Philosophie an. Das impliziert die Unterstützung von Entwurfshandlungen sowohl in Bottom-Up- als auch in Top-Down - Richtung. Benutzer können das Objektsystem um eigene Klassen erweitern bzw. existierende Klassen modifizieren und Attribute mit Defaultwerten belegen, um das System inkrementell mit Domänenwissen anreichern zu können. Von großer Bedeutung für kooperative Entwurfssysteme sind eine Versionsverwaltung und die Bereitstellung von Undo - und Redo - Mechanismen. Es ist möglich, multimediale Daten im Objektmodell abzulegen und diese in Abhängigkeit von ihrem Format wiederzugeben bzw. zu bearbeiten. Das beschriebene System befindet sich derzeit in der Implementierung.
Entwurfsprozesse im Bauwesen sind hochgradig kooperative Prozesse mit alternierenden Phasen asynchroner und synchroner Teamarbeit. Die Informationen über den aktuellen Entwurfsgegenstand können als Objektstrukturen modelliert werden, die in entsprechenden Modellverwaltungssystemen gespeichert werden. Bei der Realisierung von kooperativ nutzbaren Umgebungen für den Bauwerksentwurf sind jedoch bei der Auswahl von Basistechniken spezifische Anforderungen von CSCW-Applikationen zu beachten, die bestimmte traditionelle Verfahren nicht erfüllen. Neben verschiedenen Auswirkungen auf das Interaktionsverhalten der Entwurfsumgebung spielt die cooperation awareness der eingesetzten Mechanismen eine bedeutende Rolle. Mechanismen zur Zugriffskontrolle sind in netzwerkbasierten Mehrbenutzerumgebungen essentiell, jedoch sind herkömmliche Verfahren zu unflexibel und nicht hinreichend ausdrucksstark. Eine adaptierte und erweiterte Variante des Matrixverfahrens ist für die Anwendung in Modellverwaltungssystemen geeignet. Ebenso muss bei der Auswahl von Mechanismen zur Nebenläufigkeitskontrolle Augenmerk auf dessen Eignung in Groupware-Systemen gelegt werden. Bei der Unterstützung asynchroner Kooperation können Lock-Verfahren auf die Informationen in Modellverwaltungssystemen angewandt werden. Für die Applikationen für synchrone Teamarbeit müssen derartige Mechanismen auf die gemeinsamen Informationsbestände sowie auf Systemressourcen der Entwurfsumgebung angewendet werden. Hierfür sind floor-passing'-Verfahren geeignet; die Anwendbarkeit von Transformationsverfahren sollte für die konkret umzusetzende Applikation geprüft werden.
Modellverwaltungssysteme sind eine geeignete technologische Basis zum Management digitaler Bauwerksmodelle bei Planungstätigkeiten für den Neubau als auch für die Revitalisierung von Bauwerken. Die Unterstützung von Revitalisierungsprozessen impliziert für den Entwurf integrierter Planungsumgebungen spezifische Anforderungen wie die Repräsentation von Informationen, die mit verschiedenen Typen von Vagheit behaftet sind, die Notwendigkeit, den Soll- sowie den Ist- Zustand des Bauwerks abzubilden und die Fähigkeit des Umgangs mit temporal inkonsistenten Modellzuständen. Die erforderliche Dynamik der Domänenmodelle und die erforderliche Nutzbarkeit in Virtual Enterprises stellen weitere Ansprüche an die Realisierungsbasis der Modellverwaltungssysteme. Zur Implementierung derartiger Systeme erweist es sich als vorteilhaft, Eigenschaften objektorientierter Programmiersprachen mit nichtstatischen Typsystemen auszunutzen, da diese durch die vorhandene Metaebene sowie Introspektions- und Reflektionsmechanismen eine effiziente Realisierungsbasis bereitstellen. Zur effektiven Unterstützung synchroner kooperativer Planungstätigkeiten innerhalb einzelner Fachdisziplinen wurde ein Benachrichtigungsmechanismus realisiert, der an das Modellverwaltungssystem angekoppelte Fachapplikationen über nebenläufig vorgenommene Modifikationen am zugehörigen Domänenmodell oder an Projektinformationen informiert. Weiterhin existiert ein Mechanismus zur vereinfachten Anbindung von existierenden Applikationen, die auf statischen Partialmodellen beruhen oder standardisierte, modellbasierte Austauschformate unterstützen. Abschließend wird eine aus einem zentralen Projektserver, Domänenservern und Domänenclients bestehende hybride Systemarchitektur vorgestellt, die geeignet ist, unter den Randbedingungen kooperativer und geographisch verteilter Arbeit bei Revitalisierungsvorhaben in Virtual Enterprises eingesetzt zu werden.
The uniqueness and the long life cycle of buildings imply a dynamically modifiable building model. The technological foundation for the management of digital building models, a dynamic model management system (MMS), developed by our research group, allows to explicitly access and to modify the object model of the stored planning data. In this paper, the integration of constraints in digital building models will be shown. Constraints are conditions, which apply to the instances of domain model classes, and are defined by the user at runtime of the information system. For the expression of constraints, the Constraint Modelling Language (CML) has been developed and will be described in this paper. CML is a powerful, intuitively usable object-oriented language, which allows the expression of constraints at a high semantic level. A constrained-enabled MMS can verify, whether an instance fulfils the applying constraints. To ensure flexibility, the evaluation of constraints is not implicitly performed by the systems, but explicitly initiated by the user. A classification of constraint types and example usage scenarios are given.
The construction industry is a project-based business bringing together many different organisations to complete a desired goal. The strategic use of Information and Communication Technologies (ICT) has enabled this goal to be completed more effectively. Two issues require addressing, the technology itself and the implementation factors of the technology. Such implementation factors should consider, among other factors, the legal and contractual issues associated with the use of ICT, training requirements and its effects on the organisational culture. To date the legal and contractual issues have not been extensively covered, and it is recognised that the technologies have not been properly covered by any recognised legal and contractual practices. This in turn is threatening to inhibit the growth and prosperity of the use of the technology on construction projects. This paper discusses these legal and contractual issues and describes methods and tools that can be used to enable the growth of technology to be used in a legal and contractually valid environment.
In construction engineering, a schedule’s input data, which is usually not exactly known in the planning phase, is considered deterministic when generating the schedule. As a result, construction schedules become unreliable and deadlines are often not met. While the optimization of construction schedules with respect to costs and makespan has been a matter of research in the past decades, the optimization of the robustness of construction schedules has received little attention. In this paper, the effects of uncertainties inherent to the input data of construction schedules are discussed. Possibilities are investigated to improve the reliability of construction schedules by considering alternative processes for certain tasks and by identifying the combination of processes generating the most robust schedule with respect to the makespan of a construction project.
Collaboration in AEC Design : Web-enabling Applications using Peer-to-Peer Office Communicator
(2004)
A market analysis conducted by Gartner Dataquest in August 2001 has shown the typical characteristics of the AEC design process. High volatility in membership of AEC design groups and members dispersed over several external offices is the common collaboration scenario. Membership is most times short lived, compared to the overall duration of the process. A technical solution has to take that into account by making joining and leaving a collaborative work group very easy. The modelling of roles of collaboration between group members must be based on a commonly understood principle like the publisher / subscriber model, where the individual that is responsible for the distribution of vital information is clear. Security issues and trust in the confidentiality of the system is a central concern for the acceptance of the system. Therefore, keeping the subset of data that will be published under the absolute control of the publisher is a must. This is not the case with server-based scenarios, sometimes even due to psychological reasons. A loosely bound Peer-to-Peer network offers advantages over a server-based solution, because of less administrative overhead and simple installation procedures. In a peer-to-peer environment, a publish/subscribe role model can be more easily implemented. The publish/subscribe model matches the way AEC processes are modelled in real world scenarios today, where legal proof of information exchange between external offices is of high importance. Workflow management systems for small to midsize companies of the AEC industry may adopt the peer-to-peer approach to collaboration in the future. Further investigations are being made on the research level (WINDS) by integrating the viewer and redlining application Collaborate! into a collaborative environment.
Es wird gezeigt, daß zur Aufstellung eines korrekten Momentengleichgewichts nach Theorie zweiter Ordnung für Querkräfte die Hebelarme des unverformten Systems und für Normalkräfte Hebelarme des verformten Systems zu benutzen sind. Im Allgemeinen ist es aber nicht möglich, die Knotenverformungen eines Rahmens in relevante und nicht relevante Anteile zu zerlegen, so daß ein Momentengleichgewicht bei Berechnungen nach Theorie zweiter Ordnung im Allgemeinen nicht sinnvoll ist.
This paper deals with two different agent-based approaches aimed at the incorporation of complex design information into multi-agent planning systems. The first system facilitates collaborative structural design processes, the second one supports fire engineering in buildings. Both approaches are part of two different research projects that belong to the DFG1 priority program 1103 entitled “Network-based Co-operative Planning Processes in Structural Engineering“ (DFG 2000). The two approaches provide similar database wrapper agents to integrate relevant design information into two multi-agent systems: Database wrapper agents make the relevant product model data usable for further agents in the multi-agent system, independent on their physical location. Thus, database wrapper agents act as an interface between multi-agent system and heterogeneous database systems. The communication between the database wrapper agents and other requesting agents presumes a common vocabulary: a specific database ontology that maps database related message contents into database objects. Hereby, the software-wrapping technology enables the various design experts to plug in existing database systems and data resources into a specific multi-agent system easily. As a consequence, dynamic changes in the design information of large collaborative engineering projects are adequately supported. The flexible architecture of the database wrapper agent concept is demonstrated by the integration of an XML and a relational database system.
Der lebensdauerorientierte Entwurf von Stabbogenbrücken, mit Zuschnitt auf die Auslegung von Hängern, die durch Ermüdung infolge wirbelinduzierter Querschwingungen gefährdet sind, wird als stochastisches semi-infinites Optimierungsproblem formuliert. Zur Lösung dieses Problems sind mehrere Modellierungsebenen erforderlich, so dass ein Mehrebenenproblem entsteht. Es wird der derzeitige Entwicklungs- und Implementierungsstand bei der Umsetzung des Mehrebenenproblems in ein Entwurfsleitsystem (Software) aufgezeigt. Außerdem werden die Konzepte der noch ausstehenden Forschungsarbeit, die bereits erfolgreich beim lebensdauerorientierten Entwurf von Industriehallen mit Rahmensystem als Haupttragwerk eingesetzt wurden, diskutiert und ihre Einbildung in die bisher umgesetzte Forschungsarbeit erläutert.
A fuzzy logic controller - WNC (Water Network Control) was developed for control of urban drainage systems. The objectives are to avoid accidents, flooding, pollutions through combined sewer overflows and excessive operation and maintenance costs. Fuzzy logic was proved to be a promising approach, flexible and easy accepted, because it includes the expert knowledge. Fuzzy control system proposed is robust and also easy to understand and modified. It offers to the operator the possibility to participate directly in the system control, combining the results of the modern optimization techniques with the experience and knowledge accumulated in time by experts. Thus, the control of urban sewer system can be well solved by implementing an intelligent control system, based on available information (fuzzy) and on expert's experience. An important feature of this fuzzy logic system is its capability to elaborate a control decision even in situations that were not considered in the design phase of the urban network.
Objektorientierte Anwendungen aus dem Ingenieurwesen bestehen aus strukturierten Mengen, deren Elemente Objekte sind. Zwischen den Objekten bestehen vielfältige Abhängigkeiten. Die Beziehungen sind zur Zeit der Entwicklung einer Anwendung nur teilweise bekannt. Beziehungen zwischen Objekten müssen deshalb auch zur Laufzeit der Anwendung erzeugt und gelöscht werden können. Aufgrund des hohen Rechenaufwandes wird die Objektbasis einer Anwendung verzögert aktualisiert. Eine objektorientierte Anwendung wird auf Grundlage der Systemtheorie als System formal beschrieben. Als Elemente des Systems werden Attribute, Objekte und Objektmengen eingeführt. Die in den Methoden der Objekte implementierten Algorithmen bestimmen die Bindungsrelation des Systems. Auf Grundlage der Graphentheorie wird die Reihenfolge der Aktualisierung der Objektbasis berechnet. ...
In many engineering applications two or more different interacting systems require the numer-ical solution of so-called multifield problems. In civil engineering the interaction of fluid and structures plays an important role, i.e. for fabric tensile structures of light and flexible materials often used for large roof systems, capacious umbrellas or canopies. Whereas powerful numerical simulation techniques have been established in structural engineering as well as in fluid mechan-ics, only relatively few approaches to simulate the interaction of fluids with civil engineering constructions have been presented. To determine the wind loads on complex structures, it is still state-of-the-art to apply semi-empirical, strongly simplifying methods or to perform expensive ex-periments in wind tunnels. In this paper an approach of a coupled fluid-structure simulation will be presented for membrane and thin shell structures. The interaction is described by the struc-tural deformation as response to wind forces, resulting in a modification of the fluid flow domain. Besides a realistic determination of the wind loads, information on the structural stability can be obtained. The so-called partitioned solution is based on an iterative frame algorithm, integrating different codes for Computational Fluid Dynamics (CFD) and for Computational Structural Dy-namics (CSD) in an explicit or an implicit time-stepping procedure. All data exchange between the two different applications is performed via a neutral geometric model provided by a coupling interface. A conservative interpolation method is used for the interpolation of the nodal loads. The time-dependent motion of the structure requires a dynamic modification of the different grids and a redefinition of the Navier-Stokes equations in an Arbitrary Langrangian Eulerian (ALE) formulation. As an example for the present implementation, results of a coupled fluid-structure simulation for a textile membrane canopy will be presented.
Bei der Untersuchung hybrider Strukturen kann eine Kopplung von Modellen unterschiedlicher Modellebenen vorteilhaft sein. Durch selektive Kopplung von Tragwerks- und Querschnittsmodellen in ausgewählten Bereichen der Konstruktion kann z.B. eine Verbesserung der Abbildungsgenauigkeit erzielt werden. Dadurch werden erweiterte Aussagen über das Querschnittstragverhalten in extrem beanspruchten Teilen des Tragwerks bei optionaler Skalierbarkeit des Modellumfangs möglich. Im Beitrag werden ausgewählte Varianten der Modellbildung gegenübergestellt und bewertet. Hierbei werden Aspekte der physikalischen Nichtlinearität von hybriden Konstruktionen insbesondere von Stahlbetonkonstruktionen berücksichtigt. Die Einbeziehung von Verfahren der mathematischen Optimierung in die Berechnungsstrategie ermöglicht die Lösung der zugrunde liegenden nichtlinearen Problemstellungen unter Vorgabe von Bemessungszielen und unter Beachtung von Grenzzustandsbedingungen.
We consider an industrial application consisting of the mass minimization of a frame in an injection moulding machine. This frame has to compensate the forces acting on the mould inside the machine and has to fulfill certain critical constraints. The deformation of that frame with constant thickness is described by the plain stress state equations for linear elasticity. If the thickness varies then we use a generalized plain stress state with constant thickness in the coarse grid elements. These direct problems are solved by an adaptive multigrid solver. The mass minimization problem leads to a constrained minimization problem for a non-linear functional which will be solved by some standard optimization algorithm which requires the gradients with respect to design parameters. For the shape optimization problem, we assume that the machine components consist of simple geometrical primitives determined by a few design parameters. Therefore, we calculate the gradient in the shape optimization by means of numerical differentiation which requires the solution of approximately 4 direct problems per design parameter. The adaptive solver guarantees the detection of critical regions automatically, and ensures a good approximation to the exact solution of the direct problem. This rather slow approach can be significantly accelerated by using the adjoint method to express the gradient. It will be combined with a direct implementation of several terms that appear after applying the chain rule to the gradient.
This article discusses how the failures of construction projects could be prevented. The focus is on using IT tools in communication. The article is based on the findings of the PROLABproject. The project seeks to find solutions for how the information can effectively be used in project management, specially in construction projects, what kind of procedures help the management of the knowledge and how the obstacles for efficient ways of administrating the information can be removed. These obstacles can be either related to use of new technology or to organization culture. The paper discusses e-mail as a medium of communication with the media richness framework (Fulk & Boyd 1991) based on the interviews done with the participants of construction projects. We found out that the emails were used in both rich way and not so rich way. Obstacles of rich use of IT communication were partly technical and partly psychological. Technology acceptance model (TAM) is used to study the actual use of emails in communication. Obstacles of the use of emails were mostly individual differences like the skills to use the system or external variables like they did not have proper software to open the attachments. Also people talked about information overload. Emails often push too much information. Keywords: IT tools, Communication, Knowledge management, Construction
In this paper we revisit the so-called Bergman kernel method (BKM) for solving conformal mapping problems. This method is based on the reproducing property of the Bergman kernel function. The main drawback of this well known technique is that it involves an orthonormalization process and thus is numerically unstable. This difficulty can be, in some cases, overcome by using the Maple system, which makes no use of numeric quadrature. We illustrate this implementation by presenting a numerical example. The construction of reproducing kernel functions is not restricted to real dimension 2. Results concerning the construction of Bergman kernel functions in closed form for special domains in the framework of hypercomplex function theory suggest that BKM can also be extended to mapping problems in higher dimensions, particularly 3-dimensional cases. We describe such a generalized BKM-approach and present numerical examples obtained by the use of specially developed software packages for quaternions.
Seismic insulation is one of the most progressive types of seismic protection. Seismic insulation is understood as applying special devices for reducing of inertial seismic loads acting on a building. The constructions, shown in article, significantly more effectively solve problems of seismic protection, comparing to the existing seismic insulation systems (SIS). The Special Mechanical Engineering Design Office has developed, manufactured and tested a shock-absorber unit (SAU) of large load capacity. The SAU represents a block of number of pneumatic shock-absorbers (PSA), concentrically mounted round the guiding cylinder. The protected object rests upon the upper movable part of the guiding cylinder of the SAU. In its turn, the lower part of the SAU is rested on the foundation plate, mounted on the ground. A set of the SAU is a constructive realization of the SIS. Efficiency of such SIS has been proved as theoretically, so experimentally An effective SIS can also be created on the base of the elasto-plastic shock-absorbers developed by the KBSM. New designing and constructional solutions are based on the use of the original SIS elements, performed on the base of long time existing (in the other field of technical equipment)units, safety and durability of which have been proved by long term service (more than 20 years).
There was suggested a phenomenological modified quadratic condition of the beginning of plasticity for plastic and quasifragile orthotropic materials. Limiting surface in the shape of a paraboloid with an axis bend over hydrostatic axis corresponds to the condition. The equations of theory of current with the isotropic and anisotropic hardenings, associated with the suggested yield condition, modified into the version of determining equations of strain theory of plasticity are received. These defining equations formed the basis of highlyprecise non-classic continual (along thickness) theory of non-linear deformation of thick sandwich plates and sloping shells. In the approximations along the cross coordinate the specificity of flexural and non-flexural deformations is taken into account. The necessity of introducing the approximations of higher order, as well as accounting for the cross compression while decreasing of the relatively cross normal and shear layer rigidness is shown. The specifications, obtained in comparison with the known physically nonlinear specified model of the bending of plates with orthotropic layers are distinguished. An effective procedure of linearization of the solving equations and getting the solutions in frames of the discrete-continual scheme of the finite-element method is suggested. The approximations of higher order let to model the appearance of the cracs of layers being split by the introducing of slightly hard thin layers into the finite element, not violating the idea of continuality of theory. Calculation of a threelayer plate with rigid face diaphragms on the contour is considered
In intelligente Gebäudesysteme wird Informationstechnik in systematisch geplanter Form eingesetzt, um die Eigenschaften von Gebäuden in den Bereichen Betriebskosten, Sicherheit und Flexibilität begl. der Nutzung zu verbessern. So müssen Gebäude während ihres Lebenszyklus Nutzer- und Nutzungsänderungen bewältigen. Dies gilt nicht nur für Zweckbauten, sondern auch für Wohngebäude, die früher auf den klassischen Familientyp (4-köpfige Familie) hin optimiert wurden. Heute ist mehr eine nutzungsneutrale, funktionsoptimierbare Gestaltung von Gebäuden gefordert. Die Kleinfamilie löst sich mehr und mehr zugunsten anderer Haushaltsformen auf, ein Gebäude soll auch für Single- oder Zweipersonenhaushalte gut geeignet sein, es soll eine optimale Verbindung von Wohnen und Arbeiten zulassen oder später älteren, pflegebedürftigen Personen ein möglichst langes selbstbestimmtes Leben ermöglichen. Das System intelligentes Gebäude besteht aus der Gebäudehülle und einer Kommunikations- und Informationsverarbeitungs-Infrastruktur, zu der alle im Gebäude eingebauten Geräte gehören, die zum Betrieb des Gebäudes erforderlich sind. Die Koordination der Funktion von Einzelkomponenten erfolgt dabei weniger durch den Nutzer, sondern durch eine spezielle Software, die auf die Knoten im System verteilt ist. Diese Architektur ist Grundlage der Verbesserung der Gebäudeeigenschaften in den genannten Bereichen, die möglichen Funktionen und die damit verbundene Flexibilität in der Nutzung wird mit dem Ausdruck Intelligenz des Gebäudes assoziiiert. Der Beitrag versucht zunächst, auf Basis der Konzepte und Erfahrungen des Innovationszentrums Intelligentes Haus Duisburg, kurz inHaus, und des vom Fraunhofer-Institut IMS seit 1993 gewonnenen einschlägigen Know-Hows einen Überblick über den aktuellen Entwicklungsstand bei Systemintegrations-Technologien und -funktionen für ganzheitliche, intelligente Haus- und Gebäudesysteme zu geben, insbesondere für den Bereich der integrierten Bedienung und der Nutzung der Internet-Anbindung
Bei der Kopplung unterschiedlicher Bussysteme oder der Anbindung von Geräten an externe Netzwerke (z.B. an das Internet) stellt sich oft heraus, dass für diesen Anwendungszweck grundlegende Sicherheitsmechanismen fehlen. Durch intelligente Zusatzkomponenten, z.B. Residential Gateways, können bestehende Netzwerke erfolgreich miteinander gekoppelt werden, auch wenn sie sehr unterschiedliche Eigenschaften aufweisen. Die erforderlichen Anpassungen, Dienstekonversionen und Protokollumsetzungen können in die Gateways integriert werden, so dass gewohnte Betriebsarten, besonders bei der Konfiguration oder der Diagnose, beibehalten werden können. Bei der Nutzung vorhandener Hausbus-Infrastrukturen für sicherheitsrelevante Zusatzfunktionen wie Zugangskontrollen, Zeiterfassungen oder Alarmanlagen hingegen stellt dieser Ansatz keine Lösung dar, da hier die Sicherheit innerhalb des Systems erhöht werden muss. Daher wird für solche sicherheitsrelevanten Anwendungen oft eine separate Kommunikationsinfrastruktur verwendet, obwohl ein Gebäudebus, z.B. ein EIB-System, zur Verfügung steht. Eine praktikable Lösung stellt hierbei die Verwendung der Standard-Übertragungsmechanismen des EIB dar, bei denen jedoch die eigentlichen Nettodaten verschlüsselt werden. Auf diese Weise kann normaler Datenverkehr mit gesichertem Datenverkehr gemischt werden, wobei natürlich die sicherheitsrelevanten Teilnehmer erweiterte Funktionalitäten wie Ver- und Entschlüsselung aufweisen müssen. Dem Residential Gateway kommt in solchen Systemen neben der Kopplung der internen Netzwerke und deren Anbindung an das Internet auch das intelligente Management der Schlüssel zu. ...
The vibration control of complicated mechanical structures is impossible without proper mathematical models that allow to have a true apprehension of events occurring in structural member before the starting of the experiment and correct the diagnostic experiment in case of need. An approach that implies using of a discrete model reflecting all required features of a prototype system and permitting of an effective analytical and numerical investigation is proposed in the work. At first a discrete model of a bladed disk with flaw is considered. Taking into account the symmetry of the structure by utilization of mathematical tools of group presentation theory the number of degrees of freedom of the system is diminished. Small damage of the disk is regarded as perturbation of structure symmetry. The distinction of vibration characteristics such as natural frequencies and mode shapes of damaged and undamaged systems is determined theoretically with the help of perturbation theory and can be used as an effective diagnostic criterion of a small-scale damage of the structure. In the second part of the work a non-linear two-mass model of an acoustic emission in a damaged structure is proposed. On basis of the numerical integration of the nonlinear differential equations and expansion of the derived solution into a Fourier series free and forced vibrations of the model are investigated. It is shown that proposed model reflects all characteristic properties of vibrations of damaged structures: reduction of natural frequency, sub- and super-resonances, acoustic effects.
In dem vorliegenden Beitrag sind die Einsatzmöglichkeiten nichtlinearer Berechnungsverfahren aufgezeigt. Hierbei zeichnen sich mehrdimensionale Modelle auf Grundlage der Methode der Finiten Elemente durch die erzielbare Realitätsnähe aus. Für den Nachweis ausreichender Sicherheit in den Grenzzuständen der Trag- und Gebrauchstauglichkeit ist die Verbindung mit zuverlässigkeitstheoretischen Algorithmen dargestellt Hierbei wird die Grenzzustandsgleichung durch Ansatz eines als offene Schnittstelle konzipierten Algorithmus approximiert. Bei der Verknüpfung von nichtlinearen mechanischen Modellen und Zuverlässigkeitsanalysen wird das rechnerische Sicherheitsniveau wesentlich durch die statistischen Parameter der betrachteten Basisvariablen geprägt. Der Beitrag enthält Angaben für Verteilungsarten und -parameter für Nachweise im Stahlbetonbau
The promise of lower costs for sensors that can be used for construction inspection means that inspectors will continue to have new choices to consider in creating inspection plans. However, these emerging inspection methods can require different activities, resources, and decisions such that it can be difficult to compare the emerging methods with other methods that satisfy the same inspection needs. Furthermore, the context in which inspection is performed can significantly influence how well certain inspection methods are suited for a given set of goals for inspection. Context information, such as weather, security, and the regulatory environment, can be used to understand what information about a component should be collected and how an inspection should be performed. The research described in this paper is aimed at developing an approach for comparing and selecting inspection plans. This approach consists of (1) refinement of given goals for inspection, if necessary, in order to address any additional information needs due to a given context and in order to reach a level of detail that can be addressed by an inspection activity; (2) development of constraints to describe how an inspection should be achieved; (3) matching of goals to available inspection methods, and generation of activities and resource plans in order to address the goals; and (4) selection of an inspection plan from among the possible plans that have been identified. The authors illustrate this approach with observations made at a local construction site.
Es wird das gemeine Schema der Projektierung, die die Analyse des Marktes einschließt, betrachtet, die Einschätzung der Nomenklatur und des Umfanges des Produktionsausstoßes der Erzeugnisse, und die Schlüsselaufgabe der Wahl der Regimes der Bearbeitung. Die letzte Aufgabe wird - konkretisiert es werden die Formeln berichtet und die Algorithmen der Optimierung nach den Kriterien der Produktivität und den Selbstkostenpreisen. Es sind die Formeln für die Produktivität der Systeme mit der flexiblen Verbindung, präzisiert sowie die Abhängigkeiten für die Standhaftigkeit bei den kleinen Geschwindigkeiten des Schneidens. Die Schlüsselwörter: der Markt, die Regimes der Bearbeitung, die Produktivität, der Selbstkostenpreis, die Optimierung
Die digitale Unterstützung der Planungsprozesse ist ein aktueller Forschungs- und Arbeitsschwerpunkt der Professur Informatik in der Architektur (InfAR) und der Juniorprofessur Architekturinformatik der Fakultät Architektur an der Bauhaus-Universität Weimar. Verankert in dem DFG Sonderforschungsbereich 524 >Werkzeuge und Konstruktionen für die Revitalisierung von Bauwerken< werden Konzepte und Prototypen für eine fachlich orientierte Planungsunterstützung entwickelt. Im Rahmen unseres Forschungsschwerpunkt zur digitalen Unterstützung der Planungsprozessen, das folgende Forschungsprojekt namens, >Integrated Planning Support System for Low-Income Housing< (IPSS) konzentriert sich auf die Entwicklung einer Sammlung von computergestützten Werkzeugen, um Benutzer-entworfene Wohnungen zu unterstützen, mittels der integrativen Kombinierung von Information Systems Leistungen, Computer Assisted Designwerkzeugen und online Kommunikationstechniken. Mit diesem Set von integrierten Planungswerkzeugen erwarten wir, Bewohnern von ressourcenmangelnden Gemeinden zu ermöglichen, ihre Wohnungen-Ausdehnung effizient zu planen. In diesem Sinne, ist es auch unser Ziel die räumliche, funktionale und vielleicht auch die konstruktive Qualität Benutzer-entworfener Wohnungen zu verbessern.
In the focus of the Bologna-contract of the European secretaries of education the universities are invited to aim a unification and comparability of certificates and to offer compatible and cooperative models of education. Among existing lectures in the Internet there will arise a new competition between the universities in netbased teaching and learning environments. For the use of distributed sources of information and for the possibility to generate free configurable sequences of education modules you need management systems which are able to handle different formats of documents and to assemble it to consistent and valid lessons. Beside elementar viewing-functions, fusion of information also administrative tasks are needed, e.g. automated efficiency controls, adaptive learning surroundings. This paper attends to three aspects: - netbased teaching and learning in the area of the instruction of civil engineers - netbased information assembling and fusion of knowledge bases to higher level documents - netbased learning with international coordinated projects
Beside the standard calculation programs for civil engineering buildings mathematical programs have been lately established for the solution of differential equations for the analysis of mechanical and static systems. Programs like Maple, Matlab, MathCAD and Mathematica are popular in this field. To the knowledge of the authors, the widest application functionality offers the program Maple. Its advantages are, e.g. the alternatively symbolic or numerical solution of differential equation systems, the easy handling of parameter studies, the immediate visualization of results, the definition of macros for selected calculation steps and their export in other computer languages and, not least, the automatically generated, very clear documentation of the matehematical calculus.
In dem interdisziplinären und internationalen Verbundprojekt >2MN - Module für die multimediale netzbasierte Hochschullehre< werden diverse Lehr- und Lernmodule für ingenieur- und informationswissenschaftliche Studiengänge realisiert. Die benötigten Funktionalitäten für die Bereitstellung der verschiedenen Unterrichtsmaterialien sowie für Kommunikation, Betreuung der Kurse oder auch administrative Aufgaben im Netz werden von der in diesem Projekt entwickelten systemunabhängigen Lernplattform ELAT, der >Environment for Learning and Teaching<, zur Verfügung gestellt. Speziell für das Fachgebiet Baustatik werden vom Institut für Mechanik und Statik der Universität der Bundeswehr München einzelne Kapitel nach didaktischen Gesichtspunkten multimedial mit Text, Graphik, Bildern, Animationen und kurzen Videoclips zum systematisch angeleiteten Wissenserwerb aufbereitet. Interaktive Übungen geben Rückmeldung über den individuellen Lernfortschritt des Online-Studenten. Die Förderung der Eigeninitiative der Lernenden spielt dabei ebenso eine wichtige Rolle wie die Berücksichtigung nutzerspezifischer Lernpräferenzen. Einfach zu bedienende Statikprogramme wie der >Drehwinkeltrainer< sollen den angehenden Statikern als Kontroll- und Experimentierumgebung dienen. Das Online-Dictionary >Wörterbuch Bauwesen< erleichtert die Arbeit bei der Übersetzung baustatischer Fachtermini. Weitere Baustatik-Anwendungen, beispielsweise die Stabilitätsberechnung von Stabwerken, die Bestimmung von Querschnittswerten und die Berechnung von Biege- und Einflusslinien mit der Methode, können ortsunabhängig mit einem Pocket-PC genutzt werden.
Re-examination of the behaviour of structures can be necessary due to deterioration or changes in the traffic situation during their lifetime. The Finite Element Method (FEM) is widely used in order to accomplish numerical analysis. Considering the development of computer performance, more detailed FEM models can be analyzed, even on site, with mobile computers. To compensate the increasing amount of data needed for the model input, measures need to be taken to save time, by distributing the work. In order to provide consistency to the model, fedback data must be checked upon reception. A local wireless computer network of ultra-portable devices linked together with a computer can provide the coordination necessary for efficient parallel working. Based on a digital model consisting of all data gathered, structural modelling and numerical analysis are performed automatically. Thus, the user is released from the work that can be automatized and the time needed for the overall analysis of a structure is decreased.
We present a model derived to describe tunnel fires. The model originates in a compressible description of the air in the tunnel. It takes into account the strong buoyancy forces and at the same time the small Mach-number of the airflow. We comment on the derivation, on analytical results and on numerical simulations of the model. The model has been validated using data from real tunnel fire experiments. It shows good agreement with the real situation.
IT support for field personnel is starting to appear on bridge inspection sites, construction sites, and on the manufacturing floor. ENR magazine now regularly advertises palm computing-based systems for recording data on a construction site. This support can, and should, take on many forms and functions and needs to be carefully designed and evaluated like any other important tool used in the field. With careful design and implementation, IT devices for the field should have tremendous impact on the productivity of field personnel. If the devices are not carefully designed to take account of the field context and the abilities and preferences of the field personnel, field workers will not use these tools.
The process of matching data represented in two different data models is a longstanding issue in the exchange of data between different software systems. While the traditional manual matching approach cannot meet today’s demands on data exchange, research shows that a fully automated generic approach for model matching is not likely, and generic semi-automated approaches are not easy to implement. In this paper, we present an approach that focuses on matching data models in a specific domain. The approach combines a basic model matching approach and a version matching approach to deduce new matching rules to enable data transfer between two evolving data models.
The paper deals with the simulation of the non-linear and time dependent behaviour of complex structures in engineering. Such simulations have to provide high accuracy in the prediction of deformations and stability, by taking into account the long term influences of the non-linear behaviour of the material as well as the large deformation and contact conditions. The limiting factors of the computer simulation are the computer run time and the memory requirement during solving large scale problems. To overcome these problems we use a dynamic-explicit time integration procedure for the solution of the semi-discrete equations of motion, which is very suited for parallel processing. In the paper at first we give a brief review of the theoretical background of the mechanical modelling and the dynamic-explicit technique for the solution of the semi-discrete equations of motion. Then the concept of parallel processing will be discussed . A test example concludes the paper.
A/E/C Team members, while collaborating on building projects, rely on past experiences and content through the use of project design archives (whether in paper or digital format). This leads to underutilization of potential knowledge, as decision-making of data, information, and knowledge reuse is limited by access to these archives, due to sheer size and inconvenient presentation. This paper presents an integrated solution that leverages two technologies CoMem (Corporate Memory) and iRoom (interactive Room) developed at Stanford. This addresses critical limitations, i.e., content, context, visualization and interactivity, constraining the process of collaborative exploration towards knowledge reuse and decision-making.
Re-using knowledge in architecture, engineering and construction (AEC) firms can lead to greater competitive advantage, improved designs, and more effective management of constructed facilities. This paper discusses the importance of exploration and discovery of reusable knowledge from a corporate archive as opposed to simple search and retrieval. We describe and illustrate through a scenario of use an exploration framework and prototype, CoMemTM that formalizes the added value of exploration in the process of knowledge reuse. We discuss two exploration activities: (i) Breadth- Only overview exploration that assist a user to rapidly localize pockets of re-usable knowledge from the large corporate archive and (ii) Iterative breadth-depth exploration that enables a user to identify those re-usable components of the Corporate Memory that may yield design issues that were not originally considered.
This ethnographic study reports on emerging work processes and practices observed in the AEC (Architecture/Engineering/Construction) Global Teamwork program, i.e., what people experience when interacting with and through collaboration technologies, why people practice in the way they do, how the practice fits into the environment and changes the work patterns. It presents the experience of two high-performance typical but extreme AEC teamwork cases adopting and adapting to collaboration technologies and how these technologies in practice impact their work processes. The findings illustrate the importance of collaboration technologies in cross-disciplinary, global teamwork. Observations indicate that high performance teams that use the collaboration technologies effectively exhibit collaboration readiness at an early stage and manage to define a “third way” to meet the demands of the cross-disciplinary, multi cultural and geographically distributed AEC workspace. The observations and implications represent the blueprint for yearly innovations and improvements to the design of the AEC Global Teamwork program.
The methods currently used for scheduling building processes have some major advantages as well as disadvantages. The main advantages are the arrangement of the tasks of a project in a clear, easily readable form and the calculation of valuable information like critical paths. The main disadvantage on the other hand is the inflexibility of the model caused by the modeling paradigms. Small changes of the modeled information strongly influence the whole model and lead to the need to change many more details in the plan. In this article an approach is introduced allowing the creation of more flexible schedules. It aims towards a more robust model that lowers the need to change more than a few information while being able to calculate the important propositions of the known models and leading to further valuable conclusions.
Der Bauablauf unterliegt vielen Unwägbarkeiten. Von besonderer Bedeutung ist dieses Problem im Umfeld der Revitalisierung von Bauwerken. In weiten Teilen sind die auszuführenden Arbeiten nur schwer im Vorfeld planbar. Die Ursachen hierfür liegen großteils in der Problematik des Bauens im Bestand und dem aus wirtschaftlichen Gründen geringen Umfang von Analysen. Häufig treten verdeckte, im Vorfeld der Baumaßnahme nicht erkannte Schäden auf oder Materialstrukturen und Bauteilqualitäten wurden in der Planung unzureichend berücksichtigt. Alte Ausführungsunterlagen sind oft nicht verfügbar. Viele zur Ausführung bestimmter Arbeiten nötige Informationen fehlen und werden erst zum unmittelbaren Ausführungszeitpunkt bekannt. Einzelne Arbeiten sind nur schwer kalkulierbar bzw. planbar. Sie sind in Art und Umfang zunächst nicht bekannt und müssen gegebenenfalls als neue Vorgänge im Plan berücksichtigt werden. Diese besondere Situation bedarf einer gezielten Berücksichtigung. Die Planung des Bauablaufes muss in einer flexiblen und leicht anpassbaren Art und Weise erfolgen. Im folgenden Beitrag wird ein Ansatz zur Entwicklung eines solchen Prozessmodells vorgestellt, der im Rahmen des SFB 524 >Werkstoffe und Konstruktionen für die Revitalisierung von Bauwerken< an der Bauhaus-Universität Weimar untersucht und vorangetrieben wurde und wird. Das vorgestellte Modell kann kurzfristig flexibel auf die realen Gegebenheiten reagieren und ermöglicht trotzdem eine Planung und Steuerung des gesamten Ablaufs. Es enthält nicht wie bisher üblich deterministische Daten in starren Anordnungsbeziehungen. Vielmehr werden die Daten der Prozesse und die Beziehungen der Prozesse untereinander in einer nichtdeterministischen, unscharfen Form modelliert....
The pavement is one of the basic components of road infrastructure and, therefore, directly influences general levels of transport safety, as well as the quality of transportation services in human and cargo traffic. It also exerts a major influence on the final logistic costs of production and services in many aspects of everyday life. The continuity of transportation, which is closely tied to the development of a number of areas in the economy of every State, depends on the technical condition of the road pavement. Making proper investments in the complete course of life of the road pavement, a policy which makes sure that the conditions for continuous, safe, efficient, and economically optimised transportation are satisfied, is a priority for every administration managing municipal funds. If investments in the road pavement are not carried out properly, there usually are more and more road pavements the condition of which causes delays in transportation, and directly compromises traffic safety. Such a situation increases the running costs of vehicles, and decreases the transportation service levels and comfort of travelling. At the moment, the majority of pavements in Europe, (nearly 90% of all pavements) are flexible road pavements. Due to the prevalent number of flexible pavements in Europe, the author analyses investment in the course of full-time of life cycle of the pavements, with a stress on flexible pavements. The paper presents basic assumptions and definitions in the area of analysis of life cycle costs of a flexible road pavement, as well as profits associated with proper long range investment. The classification of damages to flexible road pavement has also been presented, and their influence on technical and use related assessment of road pavement conditions, basing on the traditional road pavement structures, with relation to the catalogue of typical flexible pavements used in Poland, as well as regarding French, British, and American experience in constructing long life road pavements. The second part of the paper discusses different investment strategies in the course of a full-time of life cycle of the road pavement, and proposes a procedure of evaluating investment strategies. The summary presents some assumptions for a global index of investment evaluation during the full-time of life cycle of a pavement, based on the Best Return Index (BRI).
This paper reports on the latest results in the development of a new approach for simulating the thermal behavior of buildings that overcomes the limitations of conventional heat-transfer simulation methods such as FDM and FEM. The proposed technique uses a coarse-grain approach to model development whereby each element represents a complete building component such as a wall, internal space, or floor. The thermal behavior of each coarse-grain element is captured using empirical modeling techniques such as artificial neural networks (ANNs). The main advantages of the approach compared to conventional simulation methods are: (a) simplified model construction for the end-user; (b) simplified model reconfiguration; (c) significantly faster simulation runs (orders of magnitude faster for two and three-dimensional models); and (d) potentially more accurate results. The paper demonstrates the viability of the approach through a number of experiments with a model of a composite wall. The approach is shown to be able to sustain highly accurate longterm simulation runs, if the coarse-grain modeling elements are implemented as ANNs. In contrast, an implementation of the coarse-grain elements using a linear model is shown to function inaccurately and erratically. The paper concludes with an identification of on-going work and future areas for development of the technique.
We describe the database requirements of SEED (Software Environment to Support the Early Phases in Building Design). The requirements are typical for a database that intends to support a heterogeneous design support environment consisting of independent software modules with diverse internal design models, requirements not met by any commercial database system. The design and implementation of this database is an integral part of the overall software engineering effort. We describe the SEED approach that integrates external and in-house software based on a shared information model specified in the modeling language SPROUT, which allows for the specification of domains, and classes, relationship types and their behavior, and multiple classifications. The SPROUT run-time system organizes and coordinates the communication between the software modules and the database
Der vorliegende Beitrag beschreibt die Problematik bei der Prognose verkehrsbedingter Schadstoff-Immissionen. Im Mittelpunkt steht die Entwicklung und der Aufbau einer Simulationsumgebung zur Evaluation von umweltorientierten Verkehrsmanagement-Strategien. Die Simulationsumgebung wird über die drei Felder Verkehr, Emission, Immission entwickelt und findet zunächst Anwendung in der Evaluation verkehrlicher Maßnahmen für die Friedberger Landstraße in Frankfurt am Main.
We present a software prototype for fluid flow problems in civil engineering, which combines essential features of Computational Steering approaches with efficient methods for model transfer and high performance computing. The main components of the system are described: - The modeler with a focus on the data management of the product model - The pre-processing and the post-processing toolkit - The simulation kernel based on the Lattice Boltzmann method - The required hardware for real-time computing
The scientific transfer of key technology features to developing countries, together with adequate competence, localisation and adaptation, is the primary purpose of the proposed investigation. It is evident that introducing high-level CAD design and detailing will improve the planning process in developing countries. Successful utilization of applied information technology for the planning process, however, depends on the user-interface of individual software. Therefore, to open the great opportunity embedded in CAD software for clients globally, the language and character-set barrier of traditional user-interfaces must be overcome. A proposal for a research program is given here to address such issue in favour of global civil engineering.
Available construction time-cost trade-off analysis models can be used to generate trade-offs between these two important objectives, however, their application is limited in large-scale construction projects due to their impractical computational requirements. This paper presents the development of a scalable and multi-objective genetic algorithm that provides the capability of simultaneously optimizing construction time and cost large-scale construction projects. The genetic algorithm was implemented in a distributed computing environment that utilizes a recent standard for parallel and distributed programming called the message passing interface (MPI). The performance of the model is evaluated using a set of measures of performance and the results demonstrate the capability of the present model in significantly reducing the computational time required to optimize large-scale construction projects.