Refine
Document Type
- Article (35)
- Doctoral Thesis (20)
- Book (6)
- Bachelor Thesis (3)
- Conference Proceeding (3)
- Periodical (2)
- Working Paper (1)
Institute
- Institut für Strukturmechanik (ISM) (18)
- Professur Stochastik und Optimierung (11)
- Junior-Professur Computational Architecture (7)
- In Zusammenarbeit mit der Bauhaus-Universität Weimar (6)
- Promotionsstudiengang Kunst und Design-Freie Kunst-Medienkunst (Ph.D) (6)
- F. A. Finger-Institut für Baustoffkunde (FIB) (5)
- Professur Denkmalpflege und Baugeschichte (4)
- An-Institute (2)
- Materialforschungs- und -prüfanstalt an der Bauhaus-Universität (2)
- Professur Baubetrieb und Bauverfahren (2)
- Professur Baumanagement und Bauwirtschaft (2)
- Professur Informatik im Bauwesen (2)
- Professur Tragwerkslehre (2)
- Professur Verkehrsplanung und Verkehrstechnik (2)
- Dozentur Film- und Medienwissenschaft (1)
- Internationales Kolleg für Kulturtechnikforschung und Medienphilosophie (IKKM) (1)
- Juniorprofessur Urban Energy Systems (1)
- Professur Bauformenlehre (1)
- Professur Biotechnologie in der Ressourcenwirtschaft (1)
- Professur Content Management und Webtechnologien (1)
- Professur Grundbau (1)
- Professur Informatik in der Architektur (1)
- Professur Medienmanagement (1)
- Professur Systeme der Virtuellen Realität (1)
- Professur Verkehrssystemplanung (1)
- Universitätsbibliothek (1)
Keywords
- Angewandte Mathematik (11)
- Stochastik (11)
- Strukturmechanik (11)
- Architektur (2)
- BIM (2)
- Building Information Modeling (2)
- Controlling (2)
- Entscheidungsunterstützung (2)
- Erdbau (2)
- Film (2)
Year of publication
- 2016 (70) (remove)
Purpose of this study is to evaluate safety impact of the deceleration lane at the Upstream Zone of at-grade U-turns on 4-lane divided Thai highways. A substantial speed reduction is required by vehicles for diverging and making U-turn, and the deceleration lanes are provided for this purpose. These lanes are also providing a storage space for the U-turning vehicles to avoid unnecessary blockage of through lanes and reduce the potential of rear-end collisions. The safety at the U-turn is greatly influenced by the proper or improper use of the deceleration lanes. Subject to their length, full or partial speed adjustment can occur within the deceleration lane also the road users’ behavior is influenced. To assess the safety impact, the four groups of U-turns with the varying length of deceleration lanes were identified. Owing to limitation of availability and reliability of road crash data in Thailand, widely accepted Traffic Conflict Technique (TCT) was used as an alternative and proactive methodology. The U-turns’ geometric data, traffic conflicts and volume data were recorded in the field at 8 locations, 8 hours per location. Severity Conflict Rate (SCR) was assessed by applying a weighing factor (based on the severity grades according to the Czech TCT) to the observed conflicts related to the conflicting traffic volumes. A comparative higher value of SCR represents a lower level of safety. According to the results, increase in the functional length of the deceleration lane yields a lower value of SCR and a higher level of the road safety.
In Zeiten volatiler Immobilienmärkte und einer hohen Wettbewerbsintensität sind leistungsfähige Systeme der Analyse und Entscheidungsunterstützung unverzichtbar. Entscheidungen zu Investitionsstrategien und Einzelinvestitionen basieren zumeist auf mehreren entscheidungsrelevanten Kriterien. Unterschiedliche immobilienwirtschaftliche Entscheidungsalternativen können dabei durchaus Kriterienausprägungen aufweisen, die eine bestimmte Alternative nicht als stets besser bzw. stets schlechter ausweisen. Klassische finanzwirtschaftliche Modelle oder verbreitete qualitative Verfahren wie das Scoring können die gegebene Komplexität meist nicht angemessen berücksichtigen. Eine Weiterentwicklung immobilienwirtschaftlicher Entscheidungsmodelle ist durch die Übertragung und Spezifizierung multikriterieller Verfahren der Entscheidungsunterstützung möglich. Speziell die Untergruppe des Outranking beschäftigt sich mit der schrittweisen Strukturierung, Ordnung und Priorisierung von komplexen Auswahlalternativen. Als spezifische immobilienwirtschaftliche Fragestellung dient hier die Auswahl und Priorisierung von Zielmärkten im taktischen Portfoliomanagement eines institutionellen Immobilienportfoliosmit internationaler Ausrichtung. Die Formalisierung des Entscheidungsproblems „Priorisierung von Zielmärkten“ erfolgt mit dem ELECTRE-Verfahren.
Previous publications about biochar in anaerobic digestion show encouraging results with regard to increased biogas yields. This work investigates such effects in a solid-state fermentation of bio-waste. Unlike in previous trials, the influence of biochar is tested with a setup that simulates an industrial-scale biogas plant. Both the biogas and the methane yield increased around 5% with a biochar addition of 5%-based on organic dry matter biochar to bio-waste. An addition of 10% increased the yield by around 3%. While scaling effects prohibit a simple transfer of the results to industrial-scale plants, and although the certainty of the results is reduced by the heterogeneity of the bio-waste, further research in this direction seems promising.
Piezoelectric materials are used in several applications as sensors and actuators where they experience high stress and electric field concentrations as a result of which they may fail due to fracture. Though there are many analytical and experimental works on piezoelectric fracture mechanics. There are very few studies about damage detection, which is an interesting way to prevent the failure of these ceramics.
An iterative method to treat the inverse problem of detecting cracks and voids in piezoelectric structures is proposed. Extended finite element method (XFEM) is employed for solving the inverse problem as it allows the use of a single regular mesh for large number of iterations with different flaw geometries.
Firstly, minimization of cost function is performed by Multilevel Coordinate Search (MCS) method. The XFEM-MCS methodology is applied to two dimensional electromechanical problems where flaws considered are straight cracks and elliptical voids. Then a numerical method based on combination of classical shape derivative and level set method for front propagation used in structural optimization is utilized to minimize the cost function. The results obtained show that the XFEM-level set methodology is effectively able to determine the number of voids in a piezoelectric structure and its corresponding locations.
The XFEM-level set methodology is improved to solve the inverse problem of detecting inclusion interfaces in a piezoelectric structure. The material interfaces are implicitly represented by level sets which are identified by applying regularisation using total variation penalty terms. The formulation is presented for three dimensional structures and inclusions made of different materials are detected by using multiple level sets. The results obtained prove that the iterative procedure proposed can determine the location and approximate shape of material subdomains in the presence of higher noise levels.
Piezoelectric nanostructures exhibit size dependent properties because of surface elasticity and surface piezoelectricity. Initially a study to understand the influence of surface elasticity on optimization of nano elastic beams is performed. The boundary of the nano structure is implicitly represented by a level set function, which is considered as the design variable in the optimization process. Two objective functions, minimizing the total potential energy of a nanostructure subjected to a material volume constraint and minimizing the least square error compared to a target
displacement, are chosen for the numerical examples. The numerical examples demonstrate the importance of size and aspect ratio in determining how surface effects impact the optimized topology of nanobeams.
Finally a conventional cantilever energy harvester with a piezoelectric nano layer is analysed. The presence of surface piezoelectricity in nano beams and nano plates leads to increase in electromechanical coupling coefficient. Topology optimization of these piezoelectric structures in an energy harvesting device to further increase energy conversion using appropriately modified XFEM-level set algorithm is performed .
Die vorliegende Arbeit untersucht das Potential von Webanwendungen in 3D zur Vermittlung von Informationen im Allgemeinen und zur Darstellung von städtebaulichen Zusammenhängen im Speziellen.
Als grundlegender Faktor der visuellen und funktionalen Qualität - welche die Wahrnehmung des Nutzers direkt beeinflusst -, erfolgt die Bewertung der Machbarkeit von 3D Webinhalten unter Anwendung einer explorativen, qualitativen Evaluierung von Webagenturen.
Darauf aufbauend wird das Potential von 3D Webanwendungen aus Nutzerperspektive untersucht, um Zusammenhänge herstellen zu können: einerseits zwischen der Machbarkeit bei der Entwicklung und anderseits die Akzeptanzkriterien beim Rezipienten betreffend.
Die empirische Studie, die mit dem Forschungspartner Bosch für diese Arbeit modelliert wurde, eruiert zum einen, inwiefern 3D im Vergleich zu 2D und 2,5D, und zum anderen WebGL im Vergleich zu bisherigen 3D Webtechnologien die visuelle Wahrnehmung und kognitive Leistungsfähigkeit des Nutzers beeinflusst.
Die Erkenntnisse der Untersuchung zeigen Parallelen zu bestehenden Studien aus web-fernen Bereichen.
Um die Bedeutung von 3D Webanwendungen zur Verbesserung von Entscheidungsprozessen in Stadtplanungsprojekten ableiten zu können, werden Aspekte zur Interaktion und visuellen Wahrnehmung in den speziellen Kontext von Stadtplanungswerkzeugen gebracht. Dabei wird überprüft, ob sich web-basierte 3D Visualisierungen sinnvoll zur Vermittlung städtebaulicher Zusammenhänge einbinden lassen und inwieweit bestehende Projekte, wie in dieser Arbeit beispielhaft das vom Fraunhofer IGD entwickelte Forschungsprojekt urbanAPI, die Technologie WebGL nutzen können.
Vor diesem Hintergrund soll die Arbeit Akzeptanzkriterien und Nutzungsbarrieren von 3D Webanwendungen auf Basis der Technologie WebGL identifizieren, um einen Beitrag zur Machbarkeit von Webanwendungen und zur Entwicklung entsprechender Stadtplanungswerkzeuge zu leisten.
In this study, the behavior of a widely graded soil prone to suffusion and necessity of homogeneity quantifi cation for such a soil in internal stability considerations are discussed. With the help of suffusion tests, the dependency of the particle washout to homogeneity of sample is shown. The validity of the great infl uence of homogeneity on suffusion processes by the presentation of arguments and evidences are established. It is emphasized that the internal stability of a widely graded soil cannot be directly correlated to the common geotechnical parameters such as dry density or permeability. The initiation and propagation of the suffusion processes are clearly a particle scale phenomenon, so the homogeneity of particle assemblies (micro-scale) has a decisive effect on particle rearrangement and washout processes. It is addressed that the guidelines for assessing internal stability lack a fundamental, scientifi c basis for quantifi cation of homogeneity. The observation of the segregation processes within the sample in an ascending layered order (for downwards fl ow) inspired the author to propose a new packing model for granular materials which are prone to internally instability.
It is shown that the particle arrangement, especially the arrangement of soil skeleton particles or the so-called primary fabric has the main role in suffusiv processes. Therefore, an experimental approach for identifi cation of the skeleton in the soil matrix is proposed. 3D models of Sequential Fill Tests using Discrete Element Method (DEM) and 3D models of granular packings for relative, stochastically and ideal homogeneous particle assemblies were generated, and simulations have been carried out.
Based on the numerical investigations and in dependency on the soil skeleton behavior, an approach for measurement of relevant scale, the so-called Representative Elementary Volume (REV) for homogeneity investigation is proposed. The development of a new testing method for quantifi cation of homogeneity is introduced (in-situ). An approach for quantifi cation of homogeneity in numerically or experimentally generated packings (samples) based on image processing method of MATLAB has been introduced. A generalized experimental method for assessment of internal stability for widely graded soils with dominant coarse matrix is developed, and a new suffusion criterion based on ideal homogeneous internally stable granular packing is designed.
My research emphasizes that in a widely graded soils with dominant coarse matrix, the soil fractions with diameters bigger than D60 build essentially the soil skeleton. The mass and spatial distribution of these fractions governs the internal stability, and the mass and distribution of the fi ll fractions are a secondary matter. For such a soil, the homogeneity of the skeleton must be cautiously measured and verified.
Das Erzeugen räumlicher Konfigurationen ist eine zentrale Aufgabe im architektonischen bzw. städtebaulichen Entwurfsprozess und hat zum Ziel, eine für Menschen angenehme Umwelt zu schaffen. Der Geometrie der entstehenden Räume kommt hierbei eine zentrale Rolle zu, da sie einen großen Einfluss auf das Empfinden und Verhalten der Menschen ausübt und nur noch mit großem Aufwand verändert werden kann, wenn sie einmal gebaut wurde. Die meisten Entscheidungen zur Festlegung der Geometrie von Räumen werden während eines sehr kurzen Zeitraums (Entwurfsphase) getroffen. Fehlentscheidungen die in dieser Phase getroffen werden haben langfristige Auswirkungen auf das Leben von Menschen, und damit auch Konsequenzen auf ökonomische und ökologische Aspekte.
Mittels computerbasierten Layoutsystemen lässt sich der Entwurf räumlicher Konfigurationen sinnvoll unterstützen, da sie es ermöglichen, in kürzester Zeit eine große Anzahl an Varianten zu erzeugen und zu überprüfen. Daraus ergeben sich zwei Vorteile. Erstens kann die große Menge an Varianten dazu beitragen, bessere Lösungen zu finden. Zweitens kann das Formalisieren von Bewertungskriterien zu einer größeren Objektivität und Transparenz bei der Lösungsfindung führen. Um den Entwurf räumlicher Konfigurationen optimal zu unterstützen, muss ein Layoutsystem in der Lage sein, ein möglichst großes Spektrum an Grundrissvarianten zu erzeugen (Vielfalt); und zahlreiche Möglichkeiten und Detaillierungsstufen zur Problembeschreibung (Flexibilität), sowie Mittel anzubieten, mit denen sich die Anforderungen an die räumliche Konfiguration adäquat beschreiben lassen (Relevanz). Bezüglich Letzterem spielen wahrnehmungs- und nutzungsbezogene Kriterien (wie z. B. Grad an Privatheit, Gefühl von Sicherheit, Raumwirkung, Orientierbarkeit, Potenzial zu sozialer Interaktion) eine wichtige Rolle.
Die bislang entwickelten Layoutsysteme weisen hinsichtlich Vielfalt, Flexibilität und Relevanz wesentliche Beschränkungen auf, welche auf eine ungeeignete Methode zur Repräsentation von Räumen zurückzuführen sind. Die in einem Layoutsystem verwendeten Raumrepräsentationsmethoden bestimmen die Möglichkeiten zur Formerzeugung und Problembeschreibung wesentlich. Sichtbarkeitsbasierte Raumrepräsentationen (Sichtfelder, Sichtachsen, Konvexe Räume) eignen sich in besonderer Weise zur Abbildung von Räumen in Layoutsystemen, da sie einerseits ein umfangreiches Repertoire zur Verfügung stellen, um räumliche Konfigurationen hinsichtlich wahrnehmungs- und nutzungsbezogener Kriterien zu beschreiben. Andererseits lassen sie sich vollständig aus der Geometrie der begrenzenden Oberflächen ableiten und sind nicht an bestimmte zur Formerzeugung verwendete geometrische Objekte gebunden.
In der vorliegenden Arbeit wird ein Layoutsystem entwickelt, welches auf diesen Raumrepräsentationen basiert. Es wird ein Evaluationsmechanismus (EM) entwickelt, welcher es ermöglicht, beliebige zweidimensionale räumliche Konfigurationen hinsichtlich wahrnehmungs- und nutzungsrelevanter Kriterien zu bewerten. Hierzu wurde eine Methodik entwickelt, die es ermöglicht automatisch Raumbereiche (O-Spaces und P-Spaces) zu identifizieren, welche bestimmte Eigenschaften haben (z.B. sichtbare Fläche, Kompaktheit des Sichtfeldes, Tageslicht) und bestimmte Relationen zueinander (wie gegenseitige Sichtbarkeit, visuelle und physische Distanz) aufweisen. Der EM wurde mit Generierungsmechanismen (GM) gekoppelt, um zu prüfen, ob dieser sich eignet, um in großen Variantenräumen nach geeigneten räumlichen Konfigurationen zu suchen. Die Ergebnisse dieser Experimente zeigen, dass die entwickelte Methodik einen vielversprechenden Ansatz zur automatisierten Erzeugung von räumlichen Konfigurationen darstellt: Erstens ist der EM vollständig vom GM getrennt, wodurch es möglich ist, verschiedene GM in einem Entwurfssystem zu verwenden und somit den Variantenraum zu vergrößern (Vielfalt). Zweitens erlaubt der EM die Anforderungen an eine räumliche Konfiguration flexibel zu beschreiben (unterschiedliche Maßstäbe, unterschiedlicher Detaillierungsgrad). Letztlich erlauben die verwendeten Repräsentationsmethoden eine Problembeschreibung vorzunehmen, die stark an der Wirkung des Raumes auf den Menschen orientiert ist (Relevanz).
Die in der Arbeit entwickelte Methodik leistet einen wichtigen Beitrag zur Verbesserung evidenzbasierter Entwurfsprozesse, da sie eine Brücke zwischen der nutzerorientierten Bewertung von räumlichen Konfigurationen und deren Erzeugung schlägt.
Problem definition and research objectives
1. The production of Portland cement clinker causes approx. 5% to 8% of the annual man-made CO2 emissions. This is due to the usage of mainly fossil fuel (approx. 40 % of the total CO2) and because of the decarbonation of limestone as a main component of the raw meal (approx. 60 % of the total CO2).
2. Various strategies are applied in order to reduce the green-house gas-emissions, such as optimizing the process of clinker production, the use of alternative fuel and the partial substitution of the clinker in blended cement by so-called SCM (supplementary cementitious materials). Hereby blast-furnace slag, fly ash and limestone are the most used materials.
3. Quaternary systems containing three SCM simultaneously besides Portland cement contribute to the reduction of CO2 emissions due to the decrease of the clinker content. In addition, such systems allow to use blast-furnace slag and fly ash in the most economical way and provide the possibility to account for shortages of SCM on the market.
4. Blast-furnace slag and fly ash show similarities in their principal chemical compositions such that similar hydrates are formed during their reaction in presence of Portland cement. Compared to ternary systems based on blast-furnace slag or fly ash besides limestone, quaternary systems that contain both, blast-furnace slag and fly ash, simultaneously besides limestone, are expected to perform similar in terms of phase assemblage and strength development.
5. The use of SCM as cement replacing materials is limited due to their generally slower reaction compared to neat cement which also leads to lower strength development, especially in the early stage of the hydration up to 28 d. To account for this it is necessary to study the reactivity of SCM such as blast-furnace slag and fly ash in detail in order to develop strategies to enhance the reactivity and thereby the strength development of SCM-containing systems.
6. The early hydration of clinker phases is studied in detail, mainly in diluted systems. It is unclear if processes that were found to control the reaction of such model systems are also prevailing in concentrated cement pastes under realistic water-to-solid ratios. Deeper insight to this aspect is needed to better understand interactions of neat Portland cement and SCM in the first hours of hydration.
State-of-the-art
7. Increasing Ca-concentrations lead to decreasing dissolution rates of C3S and C2S in diluted systems.
8. The hydration kinetics of C3S is controlled by the interplay of undersaturation with respect to C3S and oversaturation with respect to C-S-H.
9. Increasing Al-concentrations lead to a retardation of the hydration of C3S. It is unclear if the uptake of aluminum in C-S-H to form C-(A)-S-H which has a significantly lower growth rate than pure C-S-H or a retarding effect of Al on the dissolution of C3S causes this phenomenon.
10. The surface of limestone provides excellent conditions for the nucleation and growth of C-S-H such that significantly more C-S-H nuclei are formed in presence of limestone compared to other SCM.
11. The reactivity of blast-furnace slag and fly ash depends on the particle size as well as on the intrinsic reactivity of especially the amorphous phases.
12. An increase in network modifying oxides (e.g. CaO) in the chemical composition of amorphous (calcium)aluminosilicates leads to an increasingly depolymerized network which in turn causes increasing reactivity. The role of amphoteric oxides (Al2O3, Fe2O3) that can be present as network modifying oxides as well as network forming oxides is not completely solved.
13. CO2-containing AFm-phases are thermodynamically more stable than monosulfoaluminate. This indirectly stabilizes the voluminous ettringite which causes a higher total volume of hydrates and lower porosity whereby higher compressive strength is reached.
14. Only a few percent of limestone in blended cement reacts chemically dependent on the Al2O3 available for reaction. Al2O3 that is provided by the reaction of Portland cement but also by the dissolution of SCM, especially by fly ash, reacts to form hemicarboaluminate which is transformed to monocarboaluminate as the hydration proceeds.
Methodology
15. The influence of SCM on the early hydration of Portland cement in binary (including blast-furnace slag or fly ash or limestone or quartz) and ternary (including fly ash and limestone) systems was investigated applying isothermal calorimetry and analysis of the pore solution chemistry. Calculated saturation indices and solubility products of relevant phases were correlated with heat development. Based on the gained data it was reviewed if mechanisms that control the hydration of pure phases in diluted systems are also prevailing in cement pastes under realistic conditions.
16. The influence of the chemical composition of synthetic glasses on their dissolution at high pH was investigated in highly diluted systems using ion chromatography. Pozzolanity tests were conducted on pastes using simplified model systems and glass-blended Portland cements. The process of the glass dissolution was investigated by isothermal calorimetry and by thermogravimetry. Correlation of experimentally determined total bound water with bound water determined by mass balance calculations as a function of amount of glass reacted allowed to estimate the degree of glass reaction in the pastes. Further on selective dissolution experiments were carried out to crosscheck the results of the bound water/mass balance approach.
17. The reaction kinetics of quaternary pastes containing blast-furnace slag and fly ash simultaneously in the presence of limestone were investigated up to 28 d using isothermal calorimetry and chemical shrinkage measurements. In addition strength tests on mortar bars were carried out.
18. Pastes of quaternary blends were also investigated in terms of hydrate assemblage at ages of up to 182 d. Thermodynamic calculations regarding total volume of hydrates as a function of limestone and fly ash/blast-furnace slag content were conducted. The calculations were supported by thermogravimetric determination of bound water and portlandite content as well as qualitative X-ray diffraction. The results were correlated with strength tests on mortar bars.
19. The pore solutions of hydrated quaternary blends were extracted and investigated by means of ion chromatography at ages of up to 728 d. Based on the ion concentrations in the solutions saturation indices were calculated for relevant phases. In order to gain better insight to the blast-furnace slag reaction sulphate speciation was carried out at two blast furnace slag levels (20 and 30 wt.%) for selected samples up to 91 d of hydration and at 91 d for the whole matrix under investigation.
Main results
20. Investigations on the early hydration kinetics of binary systems showed a higher heat flow in presence of SCM compared to neat Portland cement. This is caused by the higher surface area that is available for the nucleation of hydrates and by the lower (over)saturation with respect to C-S-H. An increase in the Ca-concentration in the pore solution did not cause lower dissolution rates of C3S as was reported for pure phases in diluted systems. The highest dissolution was observed in the presence of limestone, i.e. at the highest Ca-concentration. The general trend of the reaction rate is inversely related to the degree of undersaturation with respect to C3S. The more undersaturated the faster the observed reaction. The presence of increasing Al-concentrations caused a retardation of the reaction which is in line with investigations on pure phases in diluted systems. Higher sulphate concentrations could be detected for the fly ash containing blend which possibly hindered ettringite precipitation and results in higher Al-concentrations. Correspondingly the low sulphate concentrations lead to lower Al-concentrations in the presence of quartz, blast-furnace slag and limestone compared to fly ash.
21. The early hydration kinetics of quaternary systems is significantly accelerated in the presence of limestone while fly ash leads to retardation. Compared to reference systems containing inert quartz, investigations by means of isothermal calorimetry and chemical shrinkage revealed an acceleration caused by blast-furnace slag. Additions of fly ash, limestone or mixtures thereof introduced another acceleration but differences are too small to be significant and clear distinguishing between the various SCM is not possible.
22. Investigations on the reactivity of synthetic glasses showed that increasing amounts of network modifying oxides caused an increase in reactivity and dissolution rates. The results reveal that Al2O3 acts mainly as network modifying oxide in all investigated glasses. Experimentally determined bound water (thermogravimetric experiments) in model systems and blended cements can be compared with bound water determined by mass balance calculations carried out as a function of the amount of glass reacted. This enables to estimate the degree of glass reaction.
23. The actual content of blast-furnace slag, fly ash or limestone does not exert significant influence on the development of compressive strength up to 7 d. At later ages thermodynamic calculations predict a degree of CaCO3 reaction of 2 to 5 wt.%. This leads to the formation of hemicarbonate and monocarbonate whereby ettringite is indirectly stabilized. As a result the total amount of solids is increased and compressive strength shows a slight maximum. Hereby the degree of CaCO3 reaction depends on the Al2O3 available for reaction which is not only provided by the dissolution of Portland cement but especially by the dissolution of the fly ash.
24. In general the presence of blast-furnace slag and fly ash in the presence of limestone exerts little influence on the hydrate assemblage. The substitution of some of the blast-furnace slag by fly ash leads to a slight decrease of portlandite and C-S-H and gives rise to the formation of more monocarbonate and hemicarbonate. Portlandite is consumed in a pozzolanic reaction with the fly ash whereby C-S-H is formed. However, the low reactivity of the fly ash causes a decrease in the amount of C-S-H formed. Thereby a lower total volume of hydrates is generated which is in line with slightly lower compressive strength in case of increasing fly ash content. The overall influence is small and all systems investigated reach strength class 42.5 N according to EN 196-1.
25. Corresponding to the investigations of the hydrate assemblage the pore solution chemistry of quaternary systems showed only small variations. Depending on the fly ash content the highest variations are observed for aluminium, i.e. increasing fly ash content leads to higher Al-concentrations. Another effect of increasing fly ash contents is an increasing undersaturation with respect to portlandite and a decreasing undersaturation with respect to strätlingite indicating the dissolution of portlandite.
26. The total concentration of sulfur in the pore solution is controlled by sulphate (SO42–) while the concentrations of sulphite (SO32–) and thiosulphate (S2O32–) were very low. Up to 2 d of hydration about 90 % of the total sulphur is present as SO42–. After 91 d this value is reduced to about 36 % while about 28 % are present as S2O32–. In general higher blast-furnace slag content leads to higher concentrations of sulphite and thiosulphate after 7 d.
Paraffin Nanocomposites for Heat Management of Lithium-Ion Batteries: A Computational Investigation
(2016)
Lithium-ion (Li-ion) batteries are currently considered as vital components for advances in mobile technologies such as those in communications and transport. Nonetheless, Li-ion batteries suffer from temperature rises which sometimes lead to operational damages or may even cause fire. An appropriate solution to control the temperature changes during the operation of Li-ion batteries is to embed batteries inside a paraffin matrix to absorb and dissipate heat. In the present work, we aimed to investigate the possibility of making paraffin nanocomposites for better heat management of a Li-ion battery pack. To fulfill this aim, heat generation during a battery charging/discharging cycles was simulated using Newman’s well established electrochemical pseudo-2D model. We couple this model to a 3D heat transfer model to predict the temperature evolution during the battery operation. In the later model, we considered different paraffin nanocomposites structures made by the addition of graphene, carbon nanotubes, and fullerene by assuming the same thermal conductivity for all fillers. This way, our results mainly correlate with the geometry of the fillers. Our results assess the degree of enhancement in heat dissipation of Li-ion batteries through the use of paraffin nanocomposites. Our results may be used as a guide for experimental set-ups to improve the heat management of Li-ion batteries.
Die Bauinformatik ist eine Säule der modernen Bau- und Umweltingenieurwissenschaften und befasst sich mit der Erforschung grundlegender informatorischer Methoden sowie mit der Anwendung und Weiterentwicklung der Informationswissenschaften im Bau- und Umweltbereich. Der Arbeitskreis Bauinformatik konstituiert sich aus Wissenschaftlern, die an Universitäten im deutschsprachigen Raum auf dem Fachgebiet Bauinformatik lehren und forschen. Ausgehend vom erreichten Entwicklungsstand der Bauinformatik skizziert dieses Positionspapier die Aufgaben des Arbeitskreises und formuliert eine Grundlage für eine abgestimmte Weiterentwicklung an den deutschsprachigen Universitäten.
Jede Baumaßnahme ist durch einen Unikatcharakter geprägt. Individuelle Planung, Vergabe und Bauvorgänge stellen immer wieder aufs Neue eine große Herausforderung dar. Durch die sich teilweise sehr schnell ändernden Randbedingungen, müssen erarbeitete Abläufe häufig schnell geändert werden. Dies geschieht heutzutage meist auf Grundlage von Erfahrungen der am Bau Beteiligten. Auch bei bester Planung und Vorbereitung können Unwägbarkeiten den Bauprozess aufhalten. Das können ungeeigneter Baugrund, verschiedenste Hinderungen im Baufeld, schlechte Witterungsverhältnisse, Ausfälle von Maschinen, veränderte Zielsetzungen des Auftraggebers und vieles mehr sein. Dies führt zu Bauzeitverlängerungen und damit zu Kostensteigerungen.
Um diesen Problemen besser begegnen zu können und diesen komplexen und fehler-anfälligen Prozess zu unterstützen, sind ein verbesserter Informationsfluss, genauere Boden-aufschlüsse und eine exaktere Dimensionierung des einzusetzenden Gerätes notwendig.
Aus diesen Gründen ist der Einsatz von Building Information Modeling (BIM) sinnvoll. BIM bietet die Möglichkeit den Informationsfluss zu verbessern, die Datengenauigkeit zu erhöhen und Abläufe zu optimieren. Außerdem ermöglicht die Anwendung Planungsschritte miteinander zu verknüpfen, Kalkulationen zu vereinfachen und das Erstellen eines intelligenten Modells, das über den gesamten Lebenszyklus erweitert werden kann.
Die Maßnahmen des Spezialtiefbaus zählen zu den kostenintensivsten auf einer Baustelle. Großes Gerät und spezialisierte Firmen sind für eine erfolgreiche Durchführung unerlässlich. Da der Baugrund immer einen großen Unsicherheitsfaktor bildet, müssen geeignete, unterstützende Anwendungen zum Einsatz kommen. Hierfür bildet BIM eine geeignete Plattform. Protokolle, Maschinendaten und Kontrolldaten können hier webbasiert analysiert und für alle zugänglich gemacht werden, um zum einen die Transparenz zu steigern und zum anderen den Überblick, selbst bei hochkomplexen Bauvorhaben zu behalten.
In dieser Arbeit soll ein Überblick über die aktuelle Forschungssituation im Bereich Building Information Modeling im Erdbau, speziell im Spezialtiefbau, gegeben werden. Die Ergebnisse die mit Hilfe vorhandener Publikationen und Forschungsarbeiten verschiedener Universitäten und namhafter Forschungsgruppen zusammengetragen wurden sollen eine Grundlage für die weitere Forschung in diesem Bereich bilden. Über die Aufgabenstellung hinaus wird zusätzlich mit dem Softwareprogramm Revit 2014 ein Modell erstellt. Es wird versucht eine überschnittene Bohrpfahlwand zu modellieren und sie mit Parametern auszustatten. Zusammenfassend wird das Programm für den Einsatz bewertet.
Looking at our face in a mirror is one of the strongest phenomenological experiences of the Self in which we need to identify the face as reflected in the mirror as belonging to us. Recent behavioral and neuroimaging studies reported that self-face identification not only relies upon visual-mnemonic representation of ones own face but also upon continuous updating and integration of visuo-tactile signals. Therefore, bodily self-consciousness plays a major role in self-face identification, with respect to interplay between unisensory and multisensory processing. However, if previous studies demonstrated that the integration of multisensory body-related signals contributes to the visual processing of ones own face, there is so far no data regarding how self-face identification, inversely, contributes to bodily self-consciousness. In the present study, we tested whether selfother face identification impacts either the egocentered or heterocentered visuo-spatial mechanisms that are core processes of bodily self-consciousness and sustain selfother distinction. For that, we developed a new paradigm, named Double Mirror. This paradigm, consisting of a semi-transparent double mirror and computer-controlled Light Emitting Diodes, elicits selfother face merging illusory effect in ecologically more valid conditions, i.e., when participants are physically facing each other and interacting. Self-face identification was manipulated by exposing pairs of participants to an Interpersonal Visual Stimulation in which the reflection of their faces merged in the mirror. Participants simultaneously performed visuo-spatial and mental own-body transformation tasks centered on their own face (egocentered) or the face of their partner (heterocentered) in the pre- and post-stimulation phase. We show that selfother face identification altered the egocentered visuo-spatial mechanisms. Heterocentered coding was preserved. Our data suggest that changes in self-face identification induced a bottom-up conflict between the current visual representation and the stored mnemonic representation of ones own face which, in turn, top-down impacted bodily self-consciousness.