Refine
Document Type
- Conference Proceeding (35)
- Article (30)
Institute
- Institut für Strukturmechanik (ISM) (34)
- In Zusammenarbeit mit der Bauhaus-Universität Weimar (15)
- Professur Angewandte Mathematik (8)
- Professur Stochastik und Optimierung (7)
- Graduiertenkolleg 1462 (4)
- Professur Informatik im Bauwesen (4)
- Institut für Konstruktiven Ingenieurbau (IKI) (2)
- Professur Computer Vision in Engineering (2)
- Professur Baubetrieb und Bauverfahren (1)
Keywords
- Angewandte Mathematik (65) (remove)
Year of publication
- 2015 (65) (remove)
A central issue for the autonomous navigation of mobile robots is to map unknown environments while simultaneously estimating its position within this map. This chicken-eggproblem is known as simultaneous localization and mapping (SLAM). Asctec’s quadrotor Pelican is a powerful and flexible research UAS (unmanned aircraft system) which enables the development of new real-time on-board algorithms for SLAM as well as autonomous navigation. The relative UAS pose estimation for SLAM, usually based on low-cost sensors like inertial measurement units (IMU) and barometers, is known to be affected by high drift rates. In order to significantly reduce these effects, we incorporate additional independent pose estimation techniques using exteroceptive sensors. In this article we present first pose estimation results using a stereo camera setup as well as a laser range finder, individually. Even though these methods fail in few certain configurations we demonstrate their effectiveness and value for the reduction of IMU drift rates and give an outlook for further works towards SLAM.
Portugal is one of the European countries with higher spatial and population freeway network coverage. The sharp growth of this network in the last years instigates the use of methods of analysis and the evaluation of their quality of service in terms of the traffic performance, typically performed through internationally accepted methodologies, namely that presented in the Highway Capacity Manual (HCM). Lately, the use of microscopic traffic simulation models has been increasingly widespread. These models simulate the individual movement of the vehicles, allowing to perform traffic analysis. The main target of this study was to verify the possibility of using microsimulation as an auxiliary tool in the adaptation of the methodology by HCM 2000 to Portugal. For this purpose, were used the microscopic simulators AIMSUN and VISSIM for the simulation of the traffic circulation in the A5 Portuguese freeway. The results allowed the analysis of the influence of the main geometric and traffic factors involved in the methodology by HCM 2000. In conclusion, the study presents the main advantages and limitations of the microsimulators AIMSUN and VISSIM in modelling the traffic circulation in Portuguese freeways. The main limitation is that these microsimulators are not able to simulate explicitly some of the factors considered in the HCM 2000 methodology, which invalidates their direct use as a tool in the quantification of those effects and, consequently, makes the direct adaptation of this methodology to Portugal impracticable.
VARIATIONAL POSITING AND SOLUTION OF COUPLED THERMOMECHANICAL PROBLEMS IN A REFERENCE CONFIGURATION
(2015)
Variational formulation of a coupled thermomechanical problem of anisotropic solids for the case of non-isothermal finite deformations in a reference configuration is shown. The formulation of the problem includes: a condition of equilibrium flow of a deformation process in the reference configuration; an equation of a coupled heat conductivity in a variational form, in which an influence of deformation characteristics of a process on the temperature field is taken into account; tensor-linear constitutive relations for a hypoelastic material; kinematic and evolutional relations; initial and boundary conditions. Based on this formulation several axisymmetric isothermal and coupled problems of finite deformations of isotropic and anisotropic bodies are solved. The solution of coupled thermomechanical problems for a hollow cylinder in case of finite deformation showed an essential influence of coupling on distribution of temperature, stresses and strains. The obtained solutions show the development of stressstrain state and temperature changing in axisymmetric bodies in the case of finite deformations.