Refine
Document Type
- Conference Proceeding (286)
- Article (3)
Institute
- In Zusammenarbeit mit der Bauhaus-Universität Weimar (174)
- Graduiertenkolleg 1462 (31)
- Professur Informatik im Bauwesen (24)
- Institut für Strukturmechanik (ISM) (22)
- Professur Angewandte Mathematik (18)
- Institut für Konstruktiven Ingenieurbau (IKI) (8)
- Professur Stahlbau (4)
- Institut für Bauinformatik, Mathematik und Bauphysik (IBMB) (3)
- Professur Informatik in der Architektur (3)
- Professur Stochastik und Optimierung (3)
Keywords
- Computerunterstütztes Verfahren (289) (remove)
Numerical simulations in the general field of civil engineering are common for the design process of structures and/or the assessment of existing buildings. The behaviour of these structures is analytically unknown and is approximated with numerical simulation methods like the Finite Element Method (FEM). Therefore the real structure is transferred into a global model (GM, e.g. concrete bridge) with a wide range of sub models (partial models PM, e.g. material modelling, creep). These partial models are coupled together to predict the behaviour of the observed structure (GM) under different conditions. The engineer needs to decide which models are suitable for computing realistically and efficiently the physical processes determining the structural behaviour. Theoretical knowledge along with the experience from prior design processes will influence this model selection decision. It is thus often a qualitative selection of different models. The goal of this paper is to present a quantitative evaluation of the global model quality according to the simulation of a bridge subject to direct loading (dead load, traffic) and indirect loading (temperature), which induce restraint effects. The model quality can be separately investigated for each partial model and also for the coupled partial models in a global structural model. Probabilistic simulations are necessary for the evaluation of these model qualities by using Uncertainty and Sensitivity Analysis. The method is applied to the simulation of a semi-integral concrete bridge with a monolithic connection between the superstructure and the piers, and elastomeric bearings at the abutments. The results show that the evaluation of global model quality is strongly dependent on the sensitivity of the considered partial models and their related quantitative prediction quality. This method is not only a relative comparison between different models, but also a quantitative representation of model quality using probabilistic simulation methods, which can support the process of model selection for numerical simulations in research and practice.
Safety operation of important civil structures such as bridges can be estimated by using fracture analysis. Since the analytical methods are not capable of solving many complicated engineering problems, numerical methods have been increasingly adopted. In this paper, a part of isotropic material which contains a crack is considered as a partial model and the proposed model quality is evaluated. EXtended IsoGeometric Analysis (XIGA) is a new developed numerical approach [1, 2] which benefits from advantages of its origins: eXtended Finite Element Method (XFEM) and IsoGeometric Analysis (IGA). It is capable of simulating crack propagation problems with no remeshing necessity and capturing singular field at the crack tip by using the crack tip enrichment functions. Also, exact representation of geometry is possible using only few elements. XIGA has also been successfully applied for fracture analysis of cracked orthotropic bodies [3] and for simulation of curved cracks [4]. XIGA applies NURBS functions for both geometry description and solution field approximation. The drawback of NURBS functions is that local refinement cannot be defined regarding that it is based on tensorproduct constructs unless multiple patches are used which has also some limitations. In this contribution, the XIGA is further developed to make the local refinement feasible by using Tspline basis functions. Adopting a recovery based error estimator in the proposed approach for evaluation of the model quality and performing the adaptive processes is in progress. Finally, some numerical examples with available analytical solutions are investigated by the developed scheme.
This paper presents a robust model updating strategy for system identification of wind turbines. To control the updating parameters and to avoid ill-conditioning, the global sensitivity analysis using the elementary effects method is conducted. The formulation of the objective function is based on M¨uller-Slany’s strategy for multi-criteria functions. As a simulationbased optimization, a simulation adapter is developed to interface the simulation software ANSYS and the locally developed optimization software MOPACK. Model updating is firstly tested on the beam model of the rotor blade. The defect between the numerical model and the reference has been markedly reduced by the process of model updating. The effect of model updating becomes more pronounced in the comparison of the measured and the numerical properties of the wind turbine model. The deviations of the frequencies of the updated model are rather small. The complete comparison including the free vibration modes by the modal assurance criteria shows the excellent coincidence of the modal parameters of the updated model with the ones from the measurements. By successful implementation of the model validation via model updating, the applicability and effectiveness of the solution concept has been demonstrated.
MODEL DESCRIBING STATIC AND DYNAMIC DISPLACEMENTS OF SILOS WALL DURING THE FLOW OF LOOSE MATERIAL
(2012)
Correct evaluation of wall displacements is a key matter when designing silos. This issue is important from both the standpoint of design engineer (load-bearing capacity of structures) and end-consumer (durability of structures). Commonplace methods of silo design mainly focus on satisfying limit states of load-bearing capacity. Current standards fail to specify methods of dynamic displacements analysis. Measurements of stressacting on silo walls prove that the actual stress is sum of static and dynamic stresses. Janssen came up with differential equation describing state of static equilibrium in cross-section of a silo. By solving the equation static stress of granular solid on silo walls can be determined. Equations of motion were determined from equilibrium equations of feature objects. General solution, describing dynamic stresses was presented as parametric model. This paper presents particular integrals of differential equation, which enable analysing displacements and vibrations for different rigidities of silo walls, types of granular solid and its flow rate.
Bridge vibration due to traffic loading has been subject of extensive research in the last decades. Such studies are concerned with deriving solutions for the bridge-vehicle interaction (BVI) and analyzing the dynamic responses considering randomness of the coupled model’s (BVI) input parameters and randomness of road unevenness. This study goes further to examine the effects of such randomness of input parameters and processes on the variance of dynamic responses in quantitative measures. The input parameters examined in the sensitivity analysis are, stiffness and damping of vehicle’s suspension system, axle spacing, and stiffness and damping of bridge. This study also examines the effects of the initial excitation of a vehicle on the influences of the considered input parameters. Variance based sensitivity analysis is often applied to deterministic models. However, the models for the dynamic problem is a stochastic one due to the simulations of the random processes. Thus, a setting using a joint meta-model; one for the mean response and other for the dispersion of the response is developed. The joint model is developed within the framework of Generalized Linear Models (GLM). An enhancement of the GLM procedure is suggested and tested; this enhancement incorporates Moving Least Squares (MLS) approximation algorithms in the fitting of the mean component of the joint model. The sensitivity analysis is then performed on the joint-model developed for the dynamic responses caused by BVI.
In this paper we review two distint complete orthogonal systems of monogenic polynomials over 3D prolate spheroids. The underlying functions take on either values in the reduced and full quaternions (identified, respectively, with R3 and R4), and are generally assumed to be nullsolutions of the well known Riesz and Moisil Théodoresco systems in R3. This will be done in the spaces of square integrable functions over R and H. The representations of these polynomials are explicitly given. Additionally, we show that these polynomial functions play an important role in defining the Szegö kernel function over the surface of 3D spheroids. As a concrete application, we prove the explicit expression of the monogenic Szegö kernel function over 3D prolate spheroids.
DISCRETE CRACK MODEL OF BORCZ FOR CALCULATING THE DEFLECTIONS OF BENDING REINFORCED CONCRETE BEAM
(2012)
In the design of the reinforced concrete beams loaded by the bending moment, it is assumed that the structure can be used at a level of load, that there are local discontinuities - cracks. Designing the element demands checking two limit states of construction, load capacity and usability. Limit states usability include also the deflection of the element. Deflections in the reinforced concrete beams with cracks are based on actual rigidity of the element. After cracking there is a local change in rigidity of the beam. The rigidity is variable in the element’s length and due to the heterogeneous structure of concrete, it is not possible to clearly describe those changes. Most standards of testing methods tend to simplify the calculations and take the average value of the beam’s rigidity on its entire length. The rigidity depends on the level of the maximal load of the beam. Experimental researches verify the value by inserting the coefficients into the formulas used in the theory of elasticity. The researches describe the changes in rigidity in the beam’s length more precisely. The authors take into consideration the change of rigidity, depending on the level of maximum load (continuum models), or localize the changes in rigidity in the area of the cracks (discrete models). This paper presents one of the discrete models. It is distinguished by the fact that the left side of the differential equation, that depends on the rigidity, is constant, and all effects associated with the scratches are taken as the external load and placed on the right side of the equation. This allows to generalize the description. The paper presents a particular integral of the differential equation, which allow analyzing the displacement and vibration for different rigidity of the silo’s walls, the flow rate and type of the flowing material.
In this paper experimental studies and numerical analysis carried out on reinforced concrete beam are partially reported. They aimed to apply the rigid finite element method to calculations for reinforced concrete beams using discrete crack model. Hence rotational ductility resulting from crack occurrence had to be determined. A relationship for calculating it in static equilibrium was proposed. Laboratory experiments proved that dynamic ductility is considerably smaller. Therefore scaling of the empirical parameter was carried out. Consequently a formula for its value depending on reinforcement ratio was obtained.
The Bernstein polynomials are used for important applications in many branches of Mathematics and the other sciences, for instance, approximation theory, probability theory, statistic theory, num- ber theory, the solution of the di¤erential equations, numerical analysis, constructing Bezier curves, q-calculus, operator theory and applications in computer graphics. The Bernstein polynomials are used to construct Bezier curves. Bezier was an engineer with the Renault car company and set out in the early 1960’s to develop a curve formulation which would lend itself to shape design. Engineers may …nd it most understandable to think of Bezier curves in terms of the center of mass of a set of point masses. Therefore, in this paper, we study on generating functions and functional equations for these polynomials. By applying these functions, we investigate interpolation function and many properties of these polynomials.
A concept of non-commutative Galois extension is introduced and binary and ternary extensions are chosen. Non-commutative Galois extensions of Nonion algebra and su(3) are constructed. Then ternary and binary Clifford analysis are introduced for non-commutative Galois extensions and the corresponding Dirac operators are associated.