Professur Bauchemie und Polymere Werkstoffe
Refine
Document Type
- Article (11)
- Doctoral Thesis (11)
- Conference Proceeding (1)
- Diploma Thesis (1)
- Habilitation (1)
Institute
- Professur Bauchemie und Polymere Werkstoffe (25) (remove)
Keywords
- Bindemittel (4)
- Wasserglas (4)
- Geopolymere (3)
- Mikrostruktur (3)
- Mörtel (3)
- Alkalisilikat (2)
- Alumosilikat (2)
- Bauchemie (2)
- Epoxidharz (2)
- Geopolymer (2)
Conventional superplasticizers based on polycarboxylate ether (PCE) show an intolerance to clay minerals due to intercalation of their polyethylene glycol (PEG) side chains into the interlayers of the clay mineral. An intolerance to very basic media is also known. This makes PCE an unsuitable choice as a superplasticizer for geopolymers. Bio-based superplasticizers derived from starch showed comparable effects to PCE in a cementitious system. The aim of the present study was to determine if starch superplasticizers (SSPs) could be a suitable additive for geopolymers by carrying out basic investigations with respect to slump, hardening, compressive and flexural strength, shrinkage, and porosity. Four SSPs were synthesized, differing in charge polarity and specific charge density. Two conventional PCE superplasticizers, differing in terms of molecular structure, were also included in this study. The results revealed that SSPs improved the slump of a metakaolin-based geopolymer (MK-geopolymer) mortar while the PCE investigated showed no improvement. The impact of superplasticizers on early hardening (up to 72 h) was negligible. Less linear shrinkage over the course of 56 days was seen for all samples in comparison with the reference. Compressive strengths of SSP specimens tested after 7 and 28 days of curing were comparable to the reference, while PCE led to a decline. The SSPs had a small impact on porosity with a shift to the formation of more gel pores while PCE caused an increase in porosity. Throughout this research, SSPs were identified as promising superplasticizers for MK-geopolymer mortar and concrete.
Ziel der Arbeit war das Adsorptionsverhalten ausgewählter schutzkolloidstabilisierter Polymerpartikel mit variierender chemischer Basis im zementären System zu beschreiben und basierend auf den gewonnenen Erkenntnissen das Konkurrenzverhalten beim Angebot unterschiedlicher mineralischer Oberflächen zu klären.
Sowohl die Destabilisierung der Polymerpartikel im alkalischen Milieu, welche eine Voraussetzung für derartige Adsorptionsprozesse ist, als auch die Veränderung von Oberflächeneigenschaften verschiedener mineralischer Partikel durch Hydratations- und Ionenadsorptionsprozesse, wurden u. a. mit Hilfe elektrokinetischer Experimente erfasst. Die spektralphotometrische Erstellung von Adsorptionsisothermen ermöglichte zudem die Ermittlung der jeweiligen adsorbierten Polymermenge zu verschiedenen Zeitpunkten der frühen Hydratation. Weiterhin wurde die Polymeradsorption an Partikeln ausgewählter Zusatzstoffe in Abhängigkeit von der Ionenstärke der Flüssigphase beschrieben.
Rasterelektronenmikroskopische Untersuchungen cryo-präparierter polymermodifizierter Zementleimproben ermöglichten es außerdem deren Mikrostruktur im suspensiven Zustand zu visualisieren. Diese Aufnahmen, ebenso wie die Ergebnisse grundlegender hydratationskinetischer Untersuchungen wurden in Wechselbeziehung zu den Ergebnissen der Adsorptionsuntersuchungen gebracht.
Maßgelbliche intermolekulare und interpartikuläre Wechselwirkungen, infolge derer sich die Stabilitätsverhältnisse im Zementleim ändern und die Polymerpartikel adsorbieren sind im Wesentlichen die Desorption des Schutzkolloids von der Polymerpartikeloberfläche, die Ionisation funktioneller Gruppen der Polymerpartikel und der Schutzkolloidmakromoleküle im alkalischen Milieu und infolgedessen die Komplexbildung mit Ionen der Zementleimporenlösung. Die Auswirkungen dieser Vorgänge auf die Lösungs- und Fällungskinetik des Zementleimes wurden erfasst und mit der chemischen Zusammensetzung der polymeren Systeme korreliert.
Strain measurement is important in mechanical testing. A wide variety of techniques exists for measuring strain in the tensile test; namely the strain gauge, extensometer, stress and strain determined by machine crosshead motion, Geometric Moire technique, optical strain measurement techniques and others. Each technique has its own advantages and disadvantages. The purpose of this study is to quantitatively compare the strain measurement techniques. To carry out the tensile test experiments for S 235, sixty samples were cut from the web of the I-profile in longitudinal and transverse directions in four different dimensions. The geometry of samples are analysed by 3D scanner and vernier caliper. In addition, the strain values were determined by using strain gauge, extensometer and machine crosshead motion. Three techniques of strain measurement are compared in quantitative manner based on the calculation of mechanical properties (modulus of elasticity, yield strength, tensile strength, percentage elongation at maximum force) of structural steel. A statistical information was used for evaluating the results. It is seen that the extensometer and strain gauge provided reliable data, however the extensometer offers several advantages over the strain gauge and crosshead motion for testing structural steel in tension. Furthermore, estimation of measurement uncertainty is presented for the basic material parameters extracted through strain measurement.
The amount of adsorbed styrene acrylate copolymer (SA) particles on cementitious surfaces at the early stage of hydration was quantitatively determined using three different methodological approaches: the depletion method, the visible spectrophotometry (VIS) and the thermo-gravimetry coupled with mass spectrometry (TG–MS). Considering the advantages and disadvantages of each method, including the respectively required sample preparation, the results for four polymer-modified cement pastes, varying in polymer content and cement fineness, were evaluated.
To some extent, significant discrepancies in the adsorption degrees were observed. There is a tendency that significantly lower amounts of adsorbed polymers were identified using TG-MS compared to values determined with the depletion method. Spectrophotometrically generated values were lying in between these extremes. This tendency was found for three of the four cement pastes examined and is originated in sample preparation and methodical limitations.
The main influencing factor is the falsification of the polymer concentration in the liquid phase during centrifugation. Interactions in the interface between sediment and supernatant are the cause. The newly developed method, using TG–MS for the quantification of SA particles, proved to be suitable for dealing with these revealed issues. Here, instead of the fluid phase, the sediment is examined with regard to the polymer content, on which the influence of centrifugation is considerably lower.