Refine
Document Type
- Article (11)
- Conference Proceeding (5)
Institute
Keywords
- Angewandte Mathematik (4)
- Angewandte Informatik (3)
- Computerunterstütztes Verfahren (3)
- Geopolymere (3)
- Epoxidharz (2)
- Mörtel (2)
- OA-Publikationsfonds2023 (2)
- Polymere (2)
- Verflüssigung (2)
- Affecting factors; Measurement uncertainty; Materials testing; Quantitative comparison; Strain comparison; Tensile test (1)
Zur Erstellung von dekorativen Plastiken sollten Mörtel entwickelt werden, die eine hohe Biegezugfestigkeit aufweisen und eine breite Palette von Konsistenzen für verschiedene Anwendungsarten, wie Gießen, Spachteln oder Stampfen abdecken. Als Basis für die Rezepturen wurde ein niedrigviskoses Epoxidharzsystem gewählt, dessen Aminhärter einen Wasseranteil von 44 % beinhaltet. Dies ermöglichte es, durch Wasserzugabe verschiedene Viskositäten einzustellen. Um dieses Wasser in massiveren Bauteilen zu binden, wurde neben Sand auch Zement als Füllstoff eingesetzt.
Die erstellten Rezepturen zeigten nach 56 Tagen hohe Druckfestigkeiten von über 50 N/mm². Mit zunehmendem Epoxidharzgehalt ergaben sich zwar steigende Biegezugfestigkeiten, jedoch unter Laborlagerung auch größere Längenänderungen. Diese konnten durch den Einsatz eines PCE-Fließmittels, PVA-Kurzfasern und einer optimierten Sieblinie verringert werden. Das Fließmittel verlängerte die Erhärtungszeiten jedoch auf bis zu 1,5 Tage.
Zur Ermittlung der Dauerhaftigkeit des Materials wurde es für drei Wochen Temperaturen von -20 bis +60 °C, einer künstlichen Sonnenbestrahlung sowie künstlicher Beregnung ausgesetzt. Im Vergleich zur Laborlagerung ergab sich bei steigendem Epoxidharzanteil ein geringerer Schwund, während die Biegezugfestigkeit der Probeköper nur geringfügig abnahm.
Rasterelektronenmikroskopische Untersuchungen zeigten, dass auch bei geringeren Epoxidharzzusätzen Störungen der Zementhydratation auftraten. Weiterhin zeigen sich bei geringen Epoxidharzzusätzen in der Matrix kugelförmige Einschlüsse, die von dispergierten Epoxidharzpartikeln stammen.
Conventional superplasticizers based on polycarboxylate ether (PCE) show an intolerance to clay minerals due to intercalation of their polyethylene glycol (PEG) side chains into the interlayers of the clay mineral. An intolerance to very basic media is also known. This makes PCE an unsuitable choice as a superplasticizer for geopolymers. Bio-based superplasticizers derived from starch showed comparable effects to PCE in a cementitious system. The aim of the present study was to determine if starch superplasticizers (SSPs) could be a suitable additive for geopolymers by carrying out basic investigations with respect to slump, hardening, compressive and flexural strength, shrinkage, and porosity. Four SSPs were synthesized, differing in charge polarity and specific charge density. Two conventional PCE superplasticizers, differing in terms of molecular structure, were also included in this study. The results revealed that SSPs improved the slump of a metakaolin-based geopolymer (MK-geopolymer) mortar while the PCE investigated showed no improvement. The impact of superplasticizers on early hardening (up to 72 h) was negligible. Less linear shrinkage over the course of 56 days was seen for all samples in comparison with the reference. Compressive strengths of SSP specimens tested after 7 and 28 days of curing were comparable to the reference, while PCE led to a decline. The SSPs had a small impact on porosity with a shift to the formation of more gel pores while PCE caused an increase in porosity. Throughout this research, SSPs were identified as promising superplasticizers for MK-geopolymer mortar and concrete.
As part of an international research project – funded by the European Union – capillary glasses for facades are being developed exploiting storage energy by means of fluids flowing through the capillaries. To meet highest visual demands, acrylate adhesives and EVA films are tested as possible bonding materials for the glass setup. Especially non-destructive methods (visual analysis, analysis of birefringent properties and computed tomographic data) are applied to evaluate failure patterns as well as the long-term behavior considering climatic influences. The experimental investigations are presented after different loading periods, providing information of failure developments. In addition, detailed information and scientific findings on the application of computed tomographic analyses are presented.
Tests on Polymer Modified Cement Concrete (PCC) have shown significant large creep deformation. The reasons for that as well as additional material phenomena are explained in the following paper. Existing creep models developed for standard concrete are studied to determine the time-dependent deformations of PCC. These models are: model B3 by Bažant and Bajewa, the models according to Model Code 90 and ACI 209 as well as model GL2000 by Gardner and Lockman. The calculated creep strains are compared to existing experimental data of PCC and the differences are pointed out. Furthermore, an optimization of the model parameters is performed to fit the models to the experimental data to achieve a better model prognosis.
Strain measurement is important in mechanical testing. A wide variety of techniques exists for measuring strain in the tensile test; namely the strain gauge, extensometer, stress and strain determined by machine crosshead motion, Geometric Moire technique, optical strain measurement techniques and others. Each technique has its own advantages and disadvantages. The purpose of this study is to quantitatively compare the strain measurement techniques. To carry out the tensile test experiments for S 235, sixty samples were cut from the web of the I-profile in longitudinal and transverse directions in four different dimensions. The geometry of samples are analysed by 3D scanner and vernier caliper. In addition, the strain values were determined by using strain gauge, extensometer and machine crosshead motion. Three techniques of strain measurement are compared in quantitative manner based on the calculation of mechanical properties (modulus of elasticity, yield strength, tensile strength, percentage elongation at maximum force) of structural steel. A statistical information was used for evaluating the results. It is seen that the extensometer and strain gauge provided reliable data, however the extensometer offers several advantages over the strain gauge and crosshead motion for testing structural steel in tension. Furthermore, estimation of measurement uncertainty is presented for the basic material parameters extracted through strain measurement.
The amount of adsorbed styrene acrylate copolymer (SA) particles on cementitious surfaces at the early stage of hydration was quantitatively determined using three different methodological approaches: the depletion method, the visible spectrophotometry (VIS) and the thermo-gravimetry coupled with mass spectrometry (TG–MS). Considering the advantages and disadvantages of each method, including the respectively required sample preparation, the results for four polymer-modified cement pastes, varying in polymer content and cement fineness, were evaluated.
To some extent, significant discrepancies in the adsorption degrees were observed. There is a tendency that significantly lower amounts of adsorbed polymers were identified using TG-MS compared to values determined with the depletion method. Spectrophotometrically generated values were lying in between these extremes. This tendency was found for three of the four cement pastes examined and is originated in sample preparation and methodical limitations.
The main influencing factor is the falsification of the polymer concentration in the liquid phase during centrifugation. Interactions in the interface between sediment and supernatant are the cause. The newly developed method, using TG–MS for the quantification of SA particles, proved to be suitable for dealing with these revealed issues. Here, instead of the fluid phase, the sediment is examined with regard to the polymer content, on which the influence of centrifugation is considerably lower.