Refine
Document Type
- Article (67) (remove)
Institute
- Professur Informatik im Bauwesen (67) (remove)
Keywords
- Modellierung (10)
- CAD (6)
- Bauwerk (5)
- Finite-Elemente-Methode (4)
- Bauwesen (3)
- Bauzeichnung (3)
- Computerunterstütztes Verfahren (3)
- Dreidimensionales Modell (3)
- Dynamische Belastung (3)
- Optimierung (3)
- Tragwerk (3)
- Anwendung (2)
- Architektur (2)
- Bauschaden (2)
- Baustatik (2)
- Datenaustausch (2)
- Datenmodell (2)
- Dialogsystem (2)
- Facility-Management (2)
- Festkörpermechanik (2)
- Freie Schwingung (2)
- Geschichtetes Medium (2)
- Graphentheorie (2)
- Ingenieurbau (2)
- Instandhaltung (2)
- Langzeitverhalten (2)
- Mathematisches Modell (2)
- Stabilität (2)
- Standardisierung (2)
- Visualisierung (2)
- Öffentlicher Personennahverkehr (2)
- Ablaufplanung (1)
- Balken (1)
- Bauaufnahme (1)
- Bauausführung (1)
- Bauplanung (1)
- Bauteil (1)
- Bauzustand (1)
- Belastung (1)
- Beltrami-Gleichung (1)
- Beschränkung (1)
- Bewertung (1)
- Bildanalyse (1)
- Boden-Bauwerk-Wechselwirkung (1)
- Bodenmechanik (1)
- Bruchmechanik (1)
- Computer Supported Cooperative Work (1)
- Computergraphik (1)
- Datenbank (1)
- Datenbankverwaltung (1)
- Diskrete Optimierung (1)
- Eigenwert (1)
- Elastomer (1)
- Elastoplastizität (1)
- Entscheidung bei mehrfacher Zielsetzung (1)
- Entscheidungsunterstützungssystem (1)
- Fraktal (1)
- Fuzzy-Logik (1)
- Gittererzeugung (1)
- Gleichgewicht (1)
- Green-Funktion (1)
- Grenzzustand (1)
- Halbraum (1)
- Heuristik (1)
- Informationsmanagement (1)
- Ingenieurholzbau (1)
- Integrierte Planung (1)
- Internet (1)
- Isotropie (1)
- Kartierung (1)
- Kennzahl (1)
- Lernendes System (1)
- Mehrdimensionalität (1)
- Mustererkennung (1)
- Nichtlineares Phänomen (1)
- Numerisches Verfahren (1)
- Objektmodell (1)
- Objektorientiertes Datenbanksystem (1)
- Parameteridentifikation (1)
- Pflasterungen (Mathematik) (1)
- Photogrammetrie (1)
- Plastizitätstheorie (1)
- Platte (1)
- Produktinformation (1)
- Programm (1)
- Projektdokumentation (1)
- Quantenphysik (1)
- Quaternion (1)
- Rekonstruktion (1)
- Ressourcenallokation (1)
- Rissbildung (1)
- Setzung (1)
- Sicherheit (1)
- Spannender Baum (1)
- Spannung (1)
- Stabwerk (1)
- Stadtplanung (1)
- Stadtverkehr (1)
- Stahlbau (1)
- Stahlbeton (1)
- Stahlkonstruktion (1)
- Stapelproblem (1)
- Stochastisches Modell (1)
- Stoffgesetz (1)
- Stokes-Problem (1)
- Straße (1)
- Strukturanalyse (1)
- Temperatur (1)
- Trajektorie (Mathematik) (1)
- Transportproblem (1)
- Trägheit (1)
- Vektorfunktion (1)
- Verbundtragwerk (1)
- Verkehrsaufkommen (1)
- Verkehrsmittelwahl (1)
- Verkehrsnetz (1)
- Versorgungsnetz (1)
- Verteiltes Datenverarbeitungssystem (1)
- Viskoplastizität (1)
- Vorspannung (1)
- Wartezeit (1)
- Wechselwirkung (1)
- Wirtschaftlichkeit (1)
- Zufallsvariable (1)
- Zuverlässigkeit (1)
- Zuverlässigkeitstheorie (1)
Year of publication
- 1997 (67) (remove)
For modeling of singular fields of stresses and deformations in elasters with a crack is offered to use of three-dimesional a special finite element. Weak compessible of elasters is taken into account on the basis of threefold approximation of fields of displacements, deformations and function of volume change. At intensive cyclic loading of the elastomer constructions with a crack it is necessary to take into account warming and large deformations at the crack top. The stress-deformed state elasters with a crack is determined from the decision of a nonlinear problem by a modified method Newton-Kantorovich. Account stress intensity factors for a rectangular plate with a various arrangement of a through crack is executed. Process of development of a surface crack and dissipative warming in prismatic a element of shift is investigated.
The effectiveness of working processes accomplished by various technological machines to a large extend depends on working quality of supply, transporting and orientating mechanisms which are very often produced as positional hydro-mechanical systems. The choice of their best type and regimes of work requires construction and analysis of models of their optimum steering which are complicated by nonlinearness, multy-criterialness of problem and also by occasional outbreaks of parameters and moments of steering regime changing. It was developed the common structure of such systems allowing within common scheme to vary the complexity degree of PHMS and the methods of inhibitory efforts supplement. For some systems which are complicated in series (from two-measured linear system to nine-measured non-linear) puzzles of the most fast zero-ambit getting are solved and two-criterial problems are analyzed. (T-min-speed, Z(T)- accuracy). There are suggested the computing procedures of optimum PHMS synthesis. The effectiveness of accepted methods of solving is asserted by the analogy of the results of gradually complicated models investigation and by their good analogy with the natural experiment. It was exposed the sense of heuristic methods of improving of approximately optimum steering, their elaboration on the base of theoretical models. The basic methods of optimum PGMS construction were also nominated.
For many purposes geometric information about existing buildings is necessary, e.g. planing of conservation or reconstruction. Architectural photogrammetry is a technique to acquire 3D geometric data of buildings for a CAD model from images. In this paper the state of the art in architectural photogrammetry and some developments towards automation are described. The photogrammetric process consists of image acquisition, orientation and restitution. Special attention is put on digital methods, from digital image acquisition to restitution methods, supported by digital image processing. There are a few field of development towards automation, e.g. feature extraction, extraction of edges and lines and the detection of corresponding points. The acquired data may be used in a CAD environment or for visualization in Virtual Reality Models, using digital orthoimages for texture mapping.
Der Effekt des praktischen Einsatzes von CAD-Systemen im Stahlbau erschöpft sich heute weitgehend in einer Verbesserung der Qualität der Planungsunterlagen und in der Verkürzung der Bearbeitungszeiten. Dabei ist bei schwierigen individuellen Konstruktionen die Einsparung an Arbeitszeit oft nicht sehr markant gegenüber einer traditionellen Arbeitsweise. Die dreidimensionale Erfassung, Speicherung und Verarbeitung von Konstruktionsdaten im Rechner verlangt neben größeren Rechenleistungen neue Verfahren für die Behandlung dieser Daten. Die Möglichkeiten der Automatisierung stahlbautypischer Produktionsvorgänge und einer variablen, computergestützten Planung erfordern wissenschaftlich-technische Betrachtungen des Gesamtproblems. Ausgehend von den Anforderungen des Stahlbaus wird ein neues dreidimensionales Volumenmodell für den rechnergestützten Entwurf und die Konstruktion erarbeitet. Es werden grundlegende Methoden zur Problembehandlung aufgezeigt. Die Methodik basiert im wesentlichen auf der Methode der Inzidenz-Matrizen, um die Beziehungen zwischen topologischen und geometrischen Informationen eines Körpers darzustellen. Die Ermittlung der lokalen Mannigfaltigkeiten wird mit dem Euler-Polyedersatz verglichen und an Beispielen demonstriert. Eine neue Methode zur Ermittlung der lokalen Mannigfaltigkeiten wird dargestellt. Stahlbauspezifische Konstruktionen werden erzeugt und ihre Gestalt nach Anforderungen verändert. Im besonderen werden stahlbauspezifische Ausklinkungen und Verschneidungen erarbeitet und an Beispielen präsentiert.
A technique for using object-oriented technologies to write structural analysis software has been developed. The structural design information of an individual building is stored in an object-oriented database. A global database provides general design values as material data and safety factors. A class library for load elements has been evolved to model the transfer of loads in a building. This class library is the basis for the development of further classes for other structural elements such as beams, columns or slabs. A software has been developed to monitor the forces transferred from one structural member to another in a building for load cases and combinations according to Eurocode 1. The results of the analysis are stored in the projects database from which a structural design report may be generated. The software was developed under Microsoft Visual C++. The Microsoft Foundation Class Library (MFC) was used to program the Graphical User Interface (GUI). Object Linking and Embedding (OLE) technology is useful to include any type of OLE server objects for example texts written with a word processor or CAD drawings in the structural design report. The Object-Oriented Database Management System (OODBMS) ObjectStore provides services to store the large amount of objects.
Objektorientierte Modellierungstechniken werden gegenwärtig vor allem Entwicklern von CAD-Systemen angeboten. Sie erzeugen über die Schritte OO-Modellanalyse und OO-Softwaredesign OO-Programme, die mit ihrer Compilation das durch den Softwareingenieur gefundene Modell festschreiben. Generell, aber insbesondere im Bauwerksdesign, ist dieses Vorgehen unbefriedigend, da hier eine Normung von Modellen nicht gelingt, der Entwurfsprozeß vergleichsweise lang ist und eine Kooperation von Ingenieurgewerken mit verschiedenen Modelldomänen die Regel sind. Darüber hinaus weisen die Modelle in frühen Phasen ein hohes Maß an Unschärfe und Abstraktion auf. CAD-Tools, die diese Phasen unterstützen, benötigen deshalb: statt eines genormten Produktmodells ein einheitliches, kognitiv begründetes Modellstrukturierungsparadigma, für das mit der Objektorientierung eine mögliche Ausprägung gegeben ist, ein explizites, verfügbares Domänenmodell zur fortwährenden Interpretation von Bauwerksmodellen, deskriptive Elemente, die die Interpretation von Objekten und Attributen erleichtern, ein Konzept zur Behandlung von Unschärfe und Abstraktion. Hieraus ergeben sich für die Entwicklung von CAD-Systemen folgende Forderungen : Explizite Verfügbarkeit von Klassenobjekten und deren Erzeugung und Veränderung zur Laufzeit, Vererbung auf Klassen- und Instanzniveau, Erweiterte Attributkonzepte (Facetten), Unterstützung der Aggregation als einer wesentlichen Modellstrukturierungsrelation, Verfügbarkeit von OO-Schnittstellen zum Aufbau von CAD-Systemen aus Tools einerseits, sowie zur Trennung von Modellverwaltung und Modellrepräsentation andererseits. Als ein herausragendes Merkmal des Objektorientierten Paradigmas wird die Anwendungsnähe genannt, da Erscheinungen der behandelten Domäne sich analog in Modellen und Programmen wiederfinden (sollen). Unter der Grundannahme, daß dieses Paradigma auch durch den Anwender zur Erstellung seiner Modellwelten verwendet wird, will FLEXOB eine homogene Umgebung schaffen, die die Modellwelt des Softwareingenieurs zu Analysezwecken dem Anwender zur Verfügung stellt und die die Erweiterung dieser Modellwelt auf deskriptivem Niveau ermöglicht. Das Tool FLEXOB und einige wesentliche Implementationsdetails werden im Beitrag vorgestellt. Es handelt sich bei diesem Tools um eine C++ Klassenbibliothek, die entweder als Objektmodul oder als Windows-DLL verwendet werden kann. Aspekte des Nutzungsregimes solch flexibler Modellverwaltungen werden im Beitrag ebenfalls angespochen.
Renovation's peculiarities of industrial enterprises in conditions of economic selfsufficiency
(1997)
Probleme of recrienfation of building complex, to the sharp increase of share of reconstruction works, capital repair and modernisation of in-dustrial plants are concidered in this work. The conception of develop-ment and creation of unitified system of expluatation and renovation of industrial plants are worded out. This system is based on date-computer technology and taking into conciderations of real economic relations.
The theory of random matrices, or random matrix theory, RMT in what follows, has been developed at the beginning of the fties to describe the sta- tistical properties of energy levels of complex quantum systems, [1], [2], [3]. In the early eighties it has enjoyed renewed interest since it has been recognized as a very useful tool in the study of numerous physical systems. Specically, it is very useful in the analysis of chaotic quantum systems. In fact, in the last years many papers appeared about the problem of quantum chaos which implies the quantization of systems whose underlying classical dynamics is irregular (i.e. chaotic). The simplest models considered in this eld are billi- ards of various shapes. From the the classical point of view, a point particle in a 2-dimensional billiard displays regular or irregular motion depending on the shape of the billiard; for instance motion in a rectangular or circular billi- ard is regular thanks to the symmetries of the boundary. On the other hand, billiards of arbitrary shapes imply chaotic motion, i.e. exponential diver- gence of initially nearby trajectories. In order to study quantum billiards we have to consider the Schroedinger equation in various 2-dimensional domains. The eigenvalues of the Schroedinger equation represent the allowed energy levels of our quantum particle in the billiard under consideration, while the eigenfunction norms represent the probability density of nding the particle in a certain position. The question of quantum chaos is whether the charac- ter of the classical motion (regular or chaotic) can in uence some properties
Methods with the convergence order p 2 (Newton`s, tangent hyperbolas, tangent parabolas etc.) and their approximate variants are studied. Conditions are presented under which the approximate variants preserve their convergence rate intrinsic to these methods and some computational aspects (possibilities to organize parallel computation, globalization of a method, the solution of the linear equations versus the matrix inversion at every iteration etc.) are discussed. Polyalgorithmic computational schemes (hybrid methods) combining the best features of various methods are developed and possibilities of their application to numerical solution of two-point boundary-value problem in ordinary differential equations and decomposition-coordination problem in convex programming are analyzed.
In the abstract proposed is the Instrumental System of mechanics problems analysis of the deformed solid body. It supplies the researcher with the possibility to describe the input data on the object under analyses and the problem scheme based upon the variational principles within one task. The particular feature of System is possibility to describe the information concerning the object of any geometrical shape and the computation sheme according to the program defined for purpose. The Methods allow to compute the tasks with indefinite functional and indefinite geometry of the object (or the set of objects). The System provides the possibility to compute the tasks with indefinite sheme based upon the Finite Element Method (FEM). The restrictions of the System usage are therefore determined by the restrictions of the FEM itself. It contrast to other known programms using FEM (ANSYS, LS-DYNA and etc) described system possesses more universality in defining input data and choosing computational scheme. Builtin is an original Subsytem of Numerical Result Analuses. It possesses the possibility to visualise all numerical results, build the epures of the unknown variables, etc. The Subsystem is approved while solving two- and three-dimensional problems of Elasticiti and Plasticity, under the conditions of Geometrical Unlinearity. Discused are Contact Problems of Statics and Dynamics.
In the design of a structure, the implementation of reliable soil-foundation-structure interaction into the analysis process plays a very important role. The paper presents a determination of parameters of a suitably chosen soil-foundation model and their influence on the structure response. Since the mechanical data for the structure can be determined with satisfactory accuracy, the properties of the soil-foundation model were identified using measured dynamic response of the real structure. A simple model describing soil-foundation structure was incorporated into the classical 3-D finite element analysis of the structure with commercial software. Results obtained from the measured data on the pier were afterwards compared with those obtained with the finite model of the pier-foundation-soil structure. On the basis of this comparison the coefficients describing the properties in the soil-foundation model were adjusted until the calculated dynamic response coincided with the measured ones. In this way, the difference between both results was reduced to 1%. Full-scale tests measuring eigenmotion of the bridge were performed through all erection stages of the new bridge in Maribor. In this way an effective and experimentally verified 3-D model for a complex dynamic analysis of the bridge under the earthquake loading was obtained. The significant advantage of the obtained model is that it was updated on the basis of the dynamic measurements thus improving the model on the basis of in-situ geomechanical measurements. The model is very accurate in describing the upper structure and economical in describing the soil mass thus representing an optimal solution regarding computational efforts.
The frame of this paper is the development of methods and procedures for the description of the motion of an arbitrary shaped foundation. Since the infinite half-space cannot be properly described by a model of finite dimensions without violating the radiation condition, the basic problems are infinite dimensions of the half-space as well as its non-homogeneous nature. Consequently, an approach has been investigated to solve this problem indirectly by developing Green's function in which the non-homogeneity and the infiniteness of the half-space has been included. When the Green's function is known, the next step will be the evaluation of contact stresses acting between the foundation and the surface of the half-space through an integral equation. The equation should be solved in the area of the foundation using Green's function as the kernel. The derivation of three-dimensional Green's function for the homogeneous half-space (Kobayashi and Sasaki 1991) has been made using the potential method. Partial differential equations occurring in the problem have been made ordinary ones through the Hankel integral transform. The general idea for obtaining the three-dimensional Green's function for the layered half-space is similar. But in that case some additional phenomena may occur. One of them is the possibility of the appearance of Stonely surface waves propagating along the contact surfaces of layers. Their contribution to the final result is in most cases important enough that they should not be neglected. The main advantage of results presented in comparing to other obtained with numerical methods is their accuracy especially in the case of thin layers because all essential steps of Green's function evaluation except of the contour integration along the branch cut have been made analytically. On the other hand the disadvantage of this method is that the mathematical effort for obtaining the Green's function is increasing drastically with the increase of the number of layers. Future work will therefore be directed in simplifying of the above described process
Für die Gestaltung einer durchgängigen Unterstützung des Entwurfsprozesses stehen gegenwärtig deskriptive Modelle der Entwurfsobjekte im Mittelpunkt der Untersuchungen. Diese Modelle gestatten das Ableiten von Repräsentationen sowie eine Weitergabe von Entwurfsergebnissen. Pragmatische Gliederungen des Entwurfsprozesses unterteilen diesen nach organisatorischen und betriebswirtschaftlichen Aspekten (Planbarkeit und Abrechenbarkeit) in eine Sequenz von Entwurfsphasen (HOAI). Diese Gliederungen berücksichtigen nicht das WIE des eigentlichen modellkreierenden Schaffensprozesses. Für ein echtes CADesign bildet dessen Klärung jedoch die erforderliche Voraussetzung. Im Beitrag wird dazu von einem vereinheitlichten Set generischer Entwurfsaktionen ausgegangen. Auch dann, wenn die verschiedenen Entwurfsphasen und die Entwurfshandlungen der einzelnen Ingenieurgewerke mit spezifische Entwurfsmodellen verbunden werden, besteht damit eine Grundlage zur methodischen Fundierung entsprechender CAD-Tools. Die methodische Verfahrensweise ähnelt der, die in Form von Styleguides zur Gestaltung von 'Graphical User Interfaces' vorgeschlagen wird. Wesentliche praktische Benutzungen solche Basisaktivitäten ergeben sich für: die Systematisierung computergestützter Entwurfshandlungen, insbesondere durch Erweiterung des deskriptiven um ein operationales Modell sowie deren erweiterte Interpretierbarkeit die Erzeugung wissensbasierter Werkzeuge zur automatischen Modellgenerierung/-konfiguration die Implementation von leistungsfähigen UNDO- bzw. TMS-Mechanismen.
Due to technological progress and European standardization (e.g. ISO certification) there is an increasing demand to automate the digital recording of building plans. Currently there are two approaches available: (1) labour-intensive redrawing with digitizing tablets or by screen digitizing, (2) automatic scanning and vectorizing where vectorization generally demands an interactive follow-up treatment due to incomplete or ambigues results. This paper proposes a knowledge-based approach for building plan analysis. The procedure reveals the following processing steps: scanning of the building plan, enhancing the image quality and binarization, extraction of lines, line junctions and character fields, knowledge-based interpretation and grouping of image features to domain specific feature aggregates like door symbols, stair symbols etc., optical character recognition and lexicon-based interpretation of character fields, matching of feature aggregates with dimension sets. First results of a prototype implementation are presented. At last an extension of the approach towards a semantic modeling concept showing a coupling between 3D object modeling and an explict 2D modeling of images and technical drawings is presented
The problem of the computation of stresses and settlements in the half-space under various types of loads is often presented in geotechnical engineering. In 1885 Boussinesq advanced theoretical expressions to determine stresses at a point within an ideal mass. His equation considers a point load on the surface of a semi-infinite, homogeneous, isotropic, weightless, elastic half-space. Newmark in 1942 performed the integration of Boussinesq's equations for the vertical stress under a corner of a rectangular area loaded with a uniform load. The problem of the determination of vertical stresses under a rectangular shaped footing has been satisfactorily solved with renewal integration of the Boussinesq's equation over the arbitrary rectangle on surface of the half-space, with a non-uniform load represented with piecewise linear interpolation functions. The problem of the determination of stresses in the case when the footing shape is an arbitrary quadrilateral however remains unsolved. The paper discusses an approach to the computation of vertical stresses and settlements in an arbitrary point of the half-space, loaded with a uniform load, which shape in the ground plan can be a general four noded form with straight edges. Since the form is transformed into a biunit square and all integrations are performed over this area, all solutions are valid also for an arbitrary triangle by the implementation of the degeneration rule.
Multimodel Numerical Analysis of the Elasto-Visco-Plastic Deformation of Materials and Constructions
(1997)
At the present time there is no a generally accepted theory of visco-plasticity which is applicable for a wide class of materials and arbitrary paths of loading. The multimodel approach, based on the creation of hierarchical sequence of the models, is the most rational. The developed library of elasto-visco-plastic models includes both simplest and sophistic models demanding numerous experimental data. A unified general form of constitutive equations for all used elasto-visco-plastic models are presented based upon the concept of tensorial internal state variables. It permits to use unified algorithm of boundary tasks solution for different variants of material models. The developed selection criteria system generates the necessary conditions and provides the choice of the simplest variant of theory sufficient for correct problem solution. Formulation of the selection criteria system is based on peculiarities of viscoplastic materials behavior for the wide range thermomechanical loading and numerous computational experiments with structures different complexity levels. A set of effective schemes of integration stress-strain relations and non-linear finite element system solution are discussed for the considered class of material models. Application possibility of different material models is studied both for material element and for complicated structures. Application of the multimodel approach in numerical computations has demonstrated possibility of reliable prediction of stress-strain response under wide variety of combined loading.
Die geometrische Modellierung hat in den Ingenieurwissenschaften eine große Bedeutung erlangt. Die Visualisierung von zwei- oder dreidimensionalen Problemstellungen ist aus heutigen Anwendungen nicht mehr wegzudenken. Zunehmend rücken Aufgabenstellungen aus dem Bereich der geometrischen Modellierung in den Vordergrund, die über die etablierten Dimensionen 1-3 hinausgehen und die nicht mehr rein geometrischer Natur sind. Hierzu zählen Aufgabenstellungen aus den Bereichen numerische Simulation, Parameteridentifikation und Strukturanalyse. Auf diese nicht-geometrischen Aufgabenstellungen sollen geometrische Verfahren, wie z.B. Triangulation, konvexe Hülle, geometrischer Schnitt und Interpolation angewendet werden. Hierzu werden diese Algorithmen, die alle auf der klassischen Geometrie des euklidischen Raumes beruhen, auf ihre Übertragbarkeit hin analysiert und überarbeitet. Am Beispiel einer Parameteridentifikation wird eine systematische Vorgehensweise vorgestellt, die es ermöglicht, trotz weniger Versuchsrechnungen den Bereich der in Frage kommenden Parameter umfassend zu beschreiben. Dies ermöglicht ein besseres Verständnis der Zusammenhänge der Parameter untereinander. Häufig existieren mehr als eine Parameterkombination, so daß diese eine Isolinie formen, die ihrerseits unendlich viele Lösungen des gestellten Problemes im Untersuchungsgebiet beschreibt.
Die Gesamtheit der Produktinformationen im Bauwesen stellt sich als sehr inkonsistente und redundante Informationsmenge dar. Die Hersteller stehen vor der Aufgabe, diese Produktinformationen nicht nur in der üblichen Katalogform sondern auch in neuen Medien wie CD-ROM und WWW zu publizieren. Einmal betriebener Erfassungsaufwand muß sich dabei durch eine einfache Mehrfachverwendung der Daten rentieren. Wegen seiner technologischen Eigenschaften eignet sich das WWW sehr gut als primäre Quelle für Produktinformationen. Vor allem wegen der möglichen Aktualität sollte es Grundlage für Publikationen in den anderen Medien sein. Mit verhältnismäßig geringem Aufwand lassen sich die WWW-Präsentation von Produktdaten so strukturieren, daß eine automatisierte Erfassung und Verarbeitung dieser Daten vereinfacht wird. So kann die Datenkonsistenz von der visuellen Präsentation in herkömmlichen Katalogen bis zur automatisch erstellten Produktdatenbank durchgängig gesichert werden. Vor dem Hintergrund der von Schnittstellenproblemen, heterogener Softwarestruktur und unzureichender Ausnutzung der Möglichkeiten der Informatik gekennzeichneten Situation im Bauwesen wird in generalisierter Ansatz mittels SGML vorgestellt. Mit einem derartigen Datenangebot werden neue, verteilte und vernetzte Anwendungen auf Grundlage derselben Produktdaten ermöglicht.
Gegenstand der Betrachtung ist ein spezielles Tourenproblem der Schüttgutoptimierung. Man stelle sich als Realitätsbezug ein Transportunternehmen vor, das eine Anzahl von gleichartigen Fahrzeugen in einem Fuhrpark stationiert hat. Vorgegebene Mengen von Schüttgut müssen von einer Kiesgrube zu mehreren Baustellen transportiert werden. Dabei sind Be- und Entladezeiten, unterschiedliche mittlere Geschwindigkeiten für Leer- bzw. Lastfahrten und Schichtzeiten zu berücksichtigen. Gesucht ist eine optimale Anzahl von einzusetzenden Fahrzeugen und die zugehörigen Tourenpläne mit dem Ziel der Minimierung der Transportkosten unter Beachtung der Lieferverträge. Die Lösung des Problems erfolgt in zwei Phasen. Zuerst wird die Frage geklärt, wieviele Fahrzeuge bei minimalem Kostenniveau einzusetzen und welche zu den Leerfahrten gehörigen Teilstrecken wie oft zu befahren sind. Anschließend wird mit heuristischen Verfahren versucht, die Menge der zu fahrenden Teilstrecken so auf die Fahrzeuge aufzuteilen, daß für jedes Fahrzeug eine zulässige Tour entsteht. Zur komplexen Lösung einer denkbaren Aufgabe liegt ein Programm in der Programmiersprache PASCAL vor. Die erzielten numerischen Resultate belegen, daß auch für Probleme größerer Dimension eine Optimallösung oder sehr gute Näherungen in vernünftiger Zeit gefunden werden.
Eine der wichtigsten Aufgaben und Herausforderungen der Bauinformatik ist gegenwärtig die Realisierung des durchgängigen, fachübergreifenden Datenflusses im Planungsprozeß eines Bauvorhabens. Im Hinblick auf die internationale Wettbewerbsfähigkeit der deutschen Bauwirtschaft ist es unumgänglich, vorhandene Effizienzpotentiale in der Bauplanung auszuschöpfen, welche durch eine qualitative Verbesserung der Planung sowie durch eine Verringerung der Bearbeitungszeit aller beteiligten Fachplanern erreicht werden können. Nach dem gegenwärtigen Stand der Technik werden die Informationsobjekte standardisiert, damit sie durchgängig nutzbar sind. Diese werden in einem allgemeingültigen Format den speziellen Programmen der Fachplaner zur Verfügung gestellt. In dieser Arbeit wird der Ansatz verfolgt, eine Integration durch die Standardisierung der Kommunikation zwischen den Informationsobjekten und ihren Anwendungsprogrammen zu erreichen. Dabei kann auf die Standardisierung der zu übertragenden Objekte verzichtet werden. Ziel der Ausarbeitung ist die Definition von implementationstechnischen Regeln, die alle auszutauschenden Objekte sowie die Anwendungen, die solche Objekte aufnehmen wollen, erfüllen müssen. Die Bearbeitung der Objekte soll in den gewohnten Anwendungen in unveränderter Weise erfolgen.