Refine
Institute
- In Zusammenarbeit mit der Bauhaus-Universität Weimar (141) (remove)
Keywords
- Architektur <Informatik> (141) (remove)
Unconstrained models are very often found in the broad spectrum of different theories of traffic demand models. In these models there are none or only one-sided restrictions influencing the choice of the individual. However in the traffic demand different deciding dependencies of the traffic volume with regard to the specific conditions of the territory structure potentials exist. Kichhoff and Lohse introduced bi- and tri-linearly constrained models to show these dependencies. In principle, the dependencies are described as hard, elastic and open boundary sum criteria. In this article a model is formulated which gets away from these predefined boundary sum criteria and allows a free determination of minimal and maximal boundary sum criteria. The iterative solution algorithm is shown according to a FURNESS procedure at the same time. With the approach of freely selectable minimal and maximal boundary sum criteria the modeling transport planner gets the possibility to show the traffic event even better. Furthermore all common boundary sum criteria can be calculated with this model. Therewith the often necessary and sensible standard and special cases can also be modeled.
Räume und Gebäude sind heute wegen der enormen Funktionalität der technischen Gebäudeausrüstung (TGA) in Kombination mit der sonstigen Ausstattung und den diversen Anwendungsprozessen und Nutzergruppen ohne innovative Konzepte der integrierten Bedienung kaum noch beherrschbar bzw. optimal nutzbar. Dies gilt sowohl für Wohn- als auch für Zweckimmobilien. Die Gebäudeleittechnik (GLT) und die Gebäudeautomation (GA) können hier unter sinnvoller Integration der Möglichkeiten der Mikroelektronik, Multimedia-, Kommunikations- und Informationstechnik erheblich zu nutzbringenden Innovationen beitragen. Die Automobilindustrie hat in den letzten Jahren gezeigt, wie durch einen integralen Systemansatz und durch Einsatz von Elektronik, Kommunikations- und Informationstechnik eine sinnvolle technische Assistenz der Anwender machbar ist. Genannt sei hier das Konzept des Cockpits mit integrierter Funktionsbündelung und der Informationskonzentration am Armaturenbrett. Im Gegensatz zum Automobil ist der Bereich der technischen Gebäudeausstattung in Wohn- und Nutzimmobilien gekennzeichnet durch eine starke Fragmentierung in unterschiedlichste Gewerke unter Beteiligung vieler oft schlecht koordinierter Akteure. Durch das Duisburger inHaus-Innovationszentrum für Intelligente Raum- und Gebäudesysteme der Fraunhofer-Gesellschaft wurden in den letzten Jahren neuartige Konzepte der Systemintegration heterogener Technik auf der Basis von Middleware-Plattformen und Multimedia-Technologien und -Geräten entwickelt, getestet und in die Anwendung getragen. Einer der ersten Systemanwendungen dieses offenen Infrastrukturkonzepts ist die integrierte Systembedienung mit zum Teil völlig neuen Bedienkonzepten und einer starken Bedienungsvereinfachung auch komplexester Technikausrüstungen in Immobilien. Der Beitrag beschreibt nach einer Analyse der Ausgangslage die technologischen Grundzüge der integrierten Systembedienung. Es folgen einige Anwendungsbeispiele und eine zusammenfassende Bewertung mit einem Ausblick auf weiterführende Aktivitäten.
In distributed project organisations and collaboration there is a need for integrating unstructured self-contained text information with structured project data. We consider this a process of text integration in which various text technologies can be used to externalise text content and consolidate it into structured information or flexibly interlink it with corresponding information bases. However, the effectiveness of text technologies and the potentials of text integration greatly vary with the type of documents, the project setup and the available background knowledge. The goal of our research is to establish text technologies within collaboration environments to allow for (a) flexibly combining appropriate text and data management technologies, (b) utilising available context information and (c) the sharing of text information in accordance to the most critical integration tasks. A particular focus is on Semantic Service Environments that leverage on Web service and Semantic Web technologies and adequately support the required systems integration and parallel processing of semi-structured and structured information. The paper presents an architecture for text integration that extends Semantic Service Environments with two types of integration services. Backbone to the Information Resource Sharing and Integration Service is a shared environment ontology that consolidates information on the project context and the available model, text and general linguistic resources. It also allows for the configuration of Semantic Text Analysis and Annotation Services to analyse the text documents as well as for capturing the discovered text information and sharing it through semantic notification and retrieval engines. A particular focus of the paper is the definition of the overall integration process configuring a complementary set of analyses and information sharing components.
The use of virtual reality techniques in the development of educational applications brings new perspectives to the teaching of subjects related to the field of civil construction in Civil Engineering domain. In order to obtain models, which would be able to visually simulate the construction process of two types of construction work, the research turned to the techniques of geometric modelling and virtual reality. The applications developed for this purpose are concerned with the construction of a cavity wall and a bridge. These models make it possible to view the physical evolution of the work, to follow the planned construction sequence and to visualize details of the form of every component of the works. They also support the study of the type and method of operation of the equipment necessary for these construction procedures. These models have been used to distinct advantage as educational aids in first-degree courses in Civil Engineering. Normally, three-dimensional geometric models, which are used to present architectural and engineering works, show only their final form, not allowing the observation of their physical evolution. The visual simulation of the construction process needs to be able to produce changes to the geometry of the project dynamically. In the present study, two engineering construction work models were created, from which it was possible to obtain three-dimensional models corresponding to different states of their form, simulating distinct stages in their construction. Virtual reality technology was applied to the 3D models. Virtual reality capacities allow the interactive real-time viewing of 3D building models and facilitate the process of visualizing, evaluating and communicating.
Die effektive Kooperation aller beteiligten Fachplaner im Bauplanungsprozess ist die Voraussetzung für wirtschaftliches und qualitativ hochwertiges Bauen. Bauprojektorganisationen bestehen in der Regel aus zahlreichen unabhängigen Planungspartnern, die örtlich verteilt spezifische Planungsaufgaben bearbeiten und die Ergebnisse in Teilproduktmodellen ablegen. Da Planungsprozesse im Bauwesen stark arbeitsteilig ablaufen, sind die Teilproduktmodelle der einzelnen Fachplanungen in hohem Maße voneinander abhängig. Ziel des hier vorgestellten Ansatzes ist die Integration der Teilproduktmodelle der Gebäudeplanung in einem netzwerkbasierten Modellverbund am Beispiel der Brandschutzplanung. Im Beitrag werden die Probleme der Verteiltheit und insbesondere der semantischen Heterogenität der involvierten Teilproduktmodelle betrachtet. Der verteilte Zugriff wird mithilfe mobiler Software-Agenten realisiert. Die Agenten können sich dabei frei im netzwerkbasierten Planungsverbund bewegen und agieren als Vertreter der Fachplaner. Das Problem der semantischen Heterogenität der Teilproduktmodelle wird auf der Basis von Ontologien gelöst. Dazu werden erstens Domänenontologien entwickelt, die Objekte der realen Welt einer abgeschlossenen Domäne, hier des Brandschutzes, abbilden. Zweitens werden Applikationsontologien entwickelt, die die einzelnen proprietären Datenhaltungen (im Sinne von Teilproduktmodellen) der jeweiligen Fachplanungen repräsentieren. Beide Ontologien werden mit einem regelbasierten Ansatz verknüpft. Im vorgestellten Anwendungsfall Brandschutz dient die Domänenontologie als einheitliche Schnittstelle für den Zugriff auf die verteilten Modelle und abstrahiert dabei von deren Datenbankspezifika und proprietären Schemata. Mithilfe von mobilen Agenten und semantischen Technologien kann so eine Plattform zur Verfügung gestellt werden, die erstens die dynamische Integration von Ressourcen in den Planungsverbund erlaubt und zweitens auf deren Basis unabhängig von der Verteiltheit und Heterogenität der eingebundenen Ressourcen ingenieurgerechte Verarbeitungsmethoden realisiert werden können.
Durch die Betrachtung des Produktions-Prozesses als zentrales Transformationselement wird die Struktur der Bauproduktion realitätsnah gefasst. Die Integration der prozessorientierten Kostendefinition setzt relevante Kostenparameter und Produktionsfaktoren so in Beziehung, dass sie im Einklang mit der realen Kostenstruktur und Kostendynamik einer Baustelle stehen. Die Beziehung zwischen Bauzeit und Kosten wird direkt erfasst und ausgewertet. Der hohen Dynamik der Bauproduktion zwischen kapazitätsbeschränkten Einsatzmitteln und Produktionsprozessen wurde durch das Poolmodell und der Simulation als Berechnungsmethode Rechnung getragen. Eine einfache Modellierung von sich zyklusartig wiederholenden Arbeitsvorgängen (Taktplanung) ist möglich. Die Taktbildung vollzieht sich bei der Simulation durch Kapazitätsbeschränkungen ohne Zutun des Benutzers. Durch eine Optimierungsmethode kann automatisiert nach der kostengünstigsten oder zeitlich schnellsten Produktionsvariante gesucht werden
MODELLING THE PLASTIC HINGE IN THE STATICALLY INDETERMINABLE REINFORCED CONCRETE BAR ELEMENTS
(2006)
The paper presents the example numerical model to calculate the reinforced concrete bar structures. Usually applied methods of structure dimensioning do not include the case of plastic hinges occurrence under the limit load of construction. The model represented by A. Borcz is based on the differential equation of deflection line of the beam and it includes the effects of rearrangement of the internal forces and reological effects. The experimental parameters obtained in earlier investigations describe effects resulting from the rise of plastic hinges in the proposed equation.
The paper presents a linear static analysis on continuous orthotropic thin-walled shell structures simply supported at the transverse ends with a random deformable contour of the cross section. The external loads can be random as well. The class of this structures involves most of the bridges, scaffold bridges, some roof structures etc. A numerical example of steel continuous structures on five spans with an open contour of the cross-section has been solved. The examination of the structure has used the following two computation models: a prismatic structure consisting of isotropic strips, a plates and ribs, with considering their real interaction, and a smooth orthotropic plate equivalent to the structure in the first model. The displacements and forces of the structure characterizing its stressed and deformed condition have been determined. The results obtained from the two solutions have been analyzed. The study on the structure is made with the force method in combination with the analytical finite strip method (AFSM) in displacements. The basic system is obtained by separating the superstructure from the understructure at the places of intermediate supports and consists of two parts. The first part is a single span thin-walled prismatic shell structure; the second part presents supports (columns, space frames etc.). The connection between the superstructure and intermediate supports is made under random supporting conditions. The forces at the supporting points in the direction of the connections removed are assumed to be the basic unknowns of the force method. The solution of the superstructure has been accomplished by the AFSM in displacements. The structure is divided in only one (transverse) direction into a finite number of plain strips connected to each other in longitudinal linear nodes. The three displacements of the points on the node lines and the rotation around those lines have been assumed to be the basic unknown in each node. The boundary conditions of each strip of the basic system correspond to the simply support along the transverse ends and the restraint along the longitudinal ones. The particular strip of the basic system has been solved by the method of the single trigonometric series. The method is reduced to solving a discrete structure in displacements and restoring its continuity at the places of the sections made in respect to both the displacements and forces. The two parts of the basic system have been solved in sequence under the action of single values of each of the basic unknowns and with the external load. The solution of the support part is accomplished using software for analyzing structures by the FEM. The basic unknown forces have been determined from system of canonic equations, the conditions of the deformations continuity on the places of the removed connections under superstructure and intermediate supports. The final displacements and forces at a random point of a continuous superstructure have been determined using the principle of superposition. The computations have been carried by software developed with Visual Fortran version 5.0 for PC.
The paper is dedicated to decidability exploration of market segmentation problem with the help of linear convolution algorithms. Mathematical formulation of this problem represents interval task of bipartite graph cover by stars. Vertices of the first partition correspond to types of commodities, vertices of the second – to customers groups. Appropriate method is offered for interval problem reduction to two-criterion task that has one implemented linear convolution algorithm. Unsolvability with the help of linear convolution algorithm of multicriterion, and consequently interval, market segmentation problem is proved.
Water resources development and management is a complex problem. It includes the design and operation of single system components, often as part of larger interrelated systems and usually on the basis of river basins. While several decades ago the dominant objective was the maximization of economic benefit, other objectives have evolved as part of the sustainable development envisaged. Today, planning and operation of larger water resources systems is practically impossible without adequate computer tools, normally being one or several models, increasingly combined with data bank management systems and multi criteria assessment procedures in decision support systems. The use of models in civil engineering already has a long history when structural engineering is considered. These design support models, however, must rather be seen as expert systems made to support the engineer with his daily work. They often have no direct link to stakeholders and the decision makers community. The scale of investigation is often much larger in water resources engineering than in structural engineering which is related to different stakeholders and decision making procedures. Still, several similarities are obvious which can be summarized as the search for a compromise solution on a complex, i.e. multiobjective and interdisciplinary decision problem. While in structural engineering e.g. aestetics, stability and energy consumption might be important evaluation criteria in addition to construction and maintenance cost other or additional criteria have to be considered in water resources planning such as political, environmental and social criteria. In this respect civil engineers tend to overemphasize technical criteria. For the future the existing expert systems should be embedded into an improved decision support shell, keeping in mind that decision makers are hardly interested in numerical modelling results. The paper will introduce into the problem and demonstrate the state of the art by means of an example.
The paper is a proposal of calculation of internal forces and dislocations in the reinforced concrete beams before and after cracking. For the ideally elastic bars transfer matrix proposed by Rakowski was applied. The effects associated with cracking were introduced by means of the Borcz's theory in the spectrally way. Numerical example was shown. The presented attitude also enables to calculate dynamic problems and those connected with the stability of the compressed and bending cracked beams and columns.
This paper deals with the development of a new multi-objective evolution strategy in combination with an integrated pollution-load and water-quality model. The optimization algorithm combines the advantages of the Non-Dominated Sorting Genetic Algorithm and Self-Adaptive Evolution Strategies. The identification of a good spread of solutions on the pareto-optimum front and the optimization of a large number of decision variables equally demands numerous simulation runs. In addition, statements with regard to the frequency of critical concentrations and peak discharges require continuous long-term simulations. Therefore, a fast operating integrated simulation model is needed providing the required precision of the results. For this purpose, a hydrological deterministic pollution-load model has been coupled with a river water-quality and a rainfall-runoff model. Wastewater treatment plants are simulated in a simplified way. The functionality of the optimization and simulation tool has been validated by analyzing a real catchment area including sewer system, WWTP, water body and natural river basin. For the optimization/rehabilitation of the urban drainage system, both innovative and approved measures have been examined and used as decision variables. As objective functions, investment costs and river water quality criteria have been used.
Requires for reliability and durability of structures and their elements with simultaneous material economy have stimulated improvement of constitutive equations for description of elasto-plastic deformation processes. This has led to the development of phenomenological modelling of complex phenomena of irreversible deformation including history-dependent and rate-dependent effects. During the last several decades many works have been devoted to the development of elasto-plastic models, in order to better predict the material behavior under combined variable thermo-mechanical loading. The increase of accuracy of stress analysis and safety factors for complex structures with the help of modern finite-element packages (ABAQUS, ANSYS, COSMOS, LS-DYNA, MSC.MARC, MSC.NASTRAN, PERMAS and other) can be provided only by use of complex and special variants of plasticity theories, which are adequate for the considered loading conditions and based on authentic information about properties of materials. The areas of application of the various theories (models) are as a rule unknown to the users of finite-element packages at the existing variety loading condition sin machine-building designs. At the moment a universal theory of inelasticity is absent and even the most accomplished theories can not guarantee adequate description of deformation processes for arbitrary structure under wide range of loading programs. The classifier of materials, loading conditions, effects (phenomena) and list of basic experiments are developed by the authors. Use of these classifiers for an establishment of hierarchy of models is a first step for introduction of the multimodel analysis into computational practice. The set of the classic and modern inelasticity theories is considered, so that they are applicable for stress analysis of structures under complex loading programs. Among them there are plastic flow theories with linear and nonlinear isotropic and kinematic hardening, multisurface theories, endochronic theory, holonomic theory, rheologic models, theory of elasto-plastic processes, slip theory, physical theories (single crystal and polycrystalline models) and others. The classification of materials provides rearranging by a degree of homogeneous, chemical composition, level of strength and plasticity, behavior under cyclic loading, anisotropy of properties at initial condition, anisotropy of properties during deformation process, structural stability. The classification of loading conditions takes into consideration proportional and non-proportional loading, temperature range, combination of cyclic and monotonous loading, one-axial, two-axial and complex stress state, curvature of strain path, presence of stress concentrators and level of strain gradient. A unified general form of constitutive equations is presented for all used material models based upon the concept of internal state variables. The wide range of mentioned above inelastic material models has been implemented into finite element program PANTOCRATOR developed by authors (see for details www.pantocrator.narod.ru). Application possibility of different material models is considered both for material element and for complex structures subjected to complex non-proportional loading.
A new application of software technology is the application area of smart living or sustainable living. Within this area application platforms are designed and realized with the goal to support value added services. In this context value added services integrates microelectronics, home automation and services to enhance the attractiveness of flats, homes and buildings. Especially real estate companies or service providers dealing with home services are interested in an effective design and management of their services. Service Engineering is the approved approach for designing customer oriented service processes. Service engineering consists of several phases; from situation analysis to service creation and service design to service management. This article will describe how the method service blueprint can be used to design service processes. Smart living includes all actions to enlarge a flat to a smart home for living. One special requirement of this application domain is the use of local components (actuators, sensors) within service processes. This article will show how this extended method supports service providers to improve the quality of customer oriented service processes and the derivation of needed interfaces of involved actors. For the civil engineering process it will be possible to derive needed information from a built in home automation system. The aim is to show, how to get needed smart local components to fullfill later offered it-supported value added services. Value added services focused on inhabitants are grouped to consulting and information, care and supervision, leisure time activities, repairs, mobility and delivery, safety and security, supply and disposal.
This research focuses on an approach to describe principles in architectural layout planning within the domain of revitalization. With the aid of mathematical rules, which are executed by a computer, solutions to design problems are generated. Provided that "design" is in principle a combinatorial problem, i.e. a constraint-based search for an overall optimal solution of a problem, an exemplary method will be described to solve such problems in architectural layout planning. To avoid conflicts relating to theoretical subtleness, a customary approach adopted from Operations Research has been chosen in this work. In this approach, design is a synonym for planning, which could be described as a systematic and methodical course of action for the analysis and solution of current or future problems. The planning task is defined as an analysis of a problem with the aim to prepare optimal decisions by the use of mathematical methods. The decision problem of a planning task is represented by an optimization model and the application of an efficient algorithm in order to aid finding one or more solutions to the problem. The basic principle underlying the approach presented herein is the understanding of design in terms of searching for solutions that fulfill specific criteria. This search is executed by the use of a constraint programming language.
In civil engineering practice, values of column forces are often required before any detailed analysis of the structure has been performed. One of the reasons for this arises from the fast-tracked nature of the majority of construction projects: foundations are laid and base columns constructed whilst analysis and design are still in progress. A need for quick results when feasibility studies are performed or when evaluating the effect of design changes on supporting columns form other situations in which column forces are required, but where a detailed analysis to get these forces seems superfluous. Thus it was concluded that the development of an efficient tool for column force calculations, in which the extensive input required in a finite element analysis is to be avoided, would be highly beneficial. The automation of the process is achieved by making use of a Voronoi diagram. The Voronoi diagram is used a) for subdividing the floor into influence areas and b) as a basis for automatic load assignment. The implemented procedure is integrated into a CAD system in which the relevant geometric information of the floor, i.e. its shape and column layout, can be defined or uploaded. A brief description of the implementation is included. Some comparative results and considerations regarding the continuation of the study are given.
Interval analysis extends the concept of computing with real numbers to computing with real intervals. As a consequence, some interesting properties appear, such as the delivery of guaranteed results or confirmed global values. The former property is given in the sense that unknown numerical values are in known to lie in a computed interval. The latter property states that the global minimum value, for example, of a given function is also known to be contained in a interval (or a finite set of intervals). Depending upon the amount computation effort invested in the calculation, we can often find tight bounds on these enclosing intervals. The downside of interval analysis, however, is the mathematically correct, but often very pessimistic size of the interval result. This is in particularly due to the so-called dependency effect, where a single variable is used multiple times in one calculation. Applying interval analysis to structural analysis problems, the dependency has a great influence on the quality of numerical results. In this paper, a brief background of interval analysis is presented and shown how it can be applied to the solution of structural analysis problems. A discussion of possible improvements as well as an outlook to parallel computing is also given.
We show a close relation between the Schrödinger equation and the conductivity equation to a Vekua equation of a special form. Under quite general conditions we propose an algorithm for explicit construction of pseudoanalytic positive formal powers for the Vekua equation that as a consequence gives us a complete system of solutions for the Schrödinger and the conductivity equations. Besides the construction of complete systems of exact solutions for the above mentioned second order equations and the Dirac equation, we discuss some other applications of pseudoanalytic function theory.