Filtern
Dokumenttyp
- Artikel (Wissenschaftlicher) (23)
- Konferenzveröffentlichung (10)
- Dissertation (10)
- Masterarbeit (3)
- Buch (Monographie) (1)
- Preprint (1)
Institut
- Professur Informatik im Bauwesen (22)
- Professur Baubetrieb und Bauverfahren (7)
- Professur Bauphysik (4)
- Institut für Strukturmechanik (ISM) (3)
- Juniorprofessur Urban Energy Systems (2)
- Professur Modellierung und Simulation - Konstruktion (2)
- Bauhaus-Institut für zukunftsweisende Infrastruktursysteme (b.is) (1)
- Institut für Konstruktiven Ingenieurbau (IKI) (1)
- Junior-Professur Computational Architecture (1)
- Juniorprofessur Simulation und Experiment (1)
Schlagworte
- Simulation (48) (entfernen)
In der vorliegenden Arbeit werden die experimentellen Ergebnisse eigener Untersuchungen an unbewehrtem und bewehrtem polymermodifiziertem Beton unter mehrfach wiederholter Druck- und Zugbeanspruchung vorgestellt und mit den Ergebnissen ähnlicher Versuche an Normalbeton und hochfestem Beton verglichen. Besondere Aufmerksamkeit wird dabei dem Formänderungsverhalten, der Steifigkeitsdegradation und der Energiedissipation sowie dem Kriechverhalten und der Mitwirkung des Betons zwischen den Rissen gewidmet. Die beobachtete signifikante Steifigkeitsdegradation sowie der ausgeprägt nichtlineare Zusammenhang zwischen der viskosen Verformung und der elastischen Stauchung zeigen, dass bei der Analyse der Kriech¬aus¬wirkungen des polymermodifizierten Betons auf das Tragverhalten entsprechender Kon¬struktionen neben den Gebrauchslasten auch die während der Lastgeschichte aufgetretenen maximalen Beanspruchungssituationen sowie die damit verbundenen Strukturveränderungen zu berücksichtigen sind. Auf der Basis der Versuchsergebnisse und der visko-elastisch-plastischen Kontinuumsschädigungstheorie werden rheologische Modelle zur Beschreibung des zeit- und beanspruchungsabhängigen Tragverhaltens von Betonbauteile vorgeschlagen. Die numerische Umsetzung der vorgeschlagenen Modelle erfolgt unter Berücksichtigung des zeitabhängigen Materialverhaltens des Betons auf der Basis des HAMILTON-Prinzips unter Vernachlässigung der Trägheitskräfte. Durch eine zeitliche Diskretisierung kann die Problembeschreibung auf das Prinzip von LAGRANGE vom Minimum des Gesamtpotentials zurückgeführt und als nichtlineare Optimierungsaufgabe formuliert werden. Die Simulation des beanspruchungsabhängigen Tragverhaltens von Stahlbetonverbundquerschnitten verdeutlicht die Qualität und Leistungsfähigkeit der vorgeschlagenen Modellbildung.
In der Arbeit wird ein räumliches Materialmodell für den anisotropen Werkstoff Holz vorgestellt. Dessen Leistungsfähigkeit wird durch Verifikationsrechnungen und die Simulation eigener Versuche aufgezeigt. In diesen Versuchen wurde das Tragverhalten spezieller Schubverbindungselemente der Brettstapel-Beton-Verbundbauweise untersucht. Die Kombination eines Brettstapels mit einer schubfest angeschlossenen Betonplatte ist eine vorteilhafte Möglichkeit, Schnittholz mit geringem Querschnitt effektiv in biegebeanspruchten Bauteilen einzusetzen. Es werden die Ergebnisse der experimentellen Untersuchungen zu den Schubverbindungselementen Flachstahlschloss und Nutverbindung vorgestellt. Diese zeichnen sich durch eine über die gesamte Plattenbreite kontinuierliche Übertragung der Schubkraft per Kontaktpressung aus. Vor allem in Brettstapel-Beton-Verbunddecken werden somit ein sehr hoher Verschiebungsmodul sowie eine eminente Tragfähigkeit erreicht. Um mit numerischen Strukturanalysen die in den Versuchen beobachteten Versagensmechanismen adäquat abbilden und realistische Prognosen für das Tragverhalten von Bauteilen oder Verbindungen treffen zu können, muss das physikalisch nichtlineare Verhalten aller beteiligter Baustoffe in die Berechnungen einbezogen werden. Im Rahmen der Dissertation wurde ein auf der Plastizitätstheorie basierendes Materialmodell für Nadelholz hergeleitet und in das FE-Programm ANSYS implementiert, welches die Mikrostruktur des Holzes als verschmierendes Ersatzkontinuum erfasst. Anhand des anatomischen Aufbaus des inhomogenen, anisotropen und porigen Werkstoffs werden die holzspezifischen Versagensmechanismen und die daraus abgeleiteten konstitutiven Beziehungen erläutert. Das ausgeprägt anisotrope Tragverhalten von Holz ist vor allem durch erstaunliche Duktilität bei Stauchung, sprödes Versagen bei Zug- und Schubbeanspruchung und enorme Festigkeitsunterschiede in den Wuchsrichtungen gekennzeichnet. Die Auswirkungen der größtenteils unabhängig voneinander auftretenden, mikromechanischen Versagensmechanismen auf die Spannungs-Verformungsbeziehungen wurden durch die Formulierung adäquater Ver- resp. Entfestigungsfunktionen in Abhängigkeit der Beanspruchungsmodi erfasst. Das dem Materialmodell zu Grunde liegende mehrflächige Fließkriterium berücksichtigt die Interaktion aller sechs Komponenten des räumlichen Spannungszustandes. Die durchgeführten Verifikations- und Simulationsberechnungen belegen, dass der erarbeitete Ansatz sowohl zur Bewertung des Tragvermögens als auch zur Beurteilung von Riss- bzw. Schädigungsursachen von Holzbauteilen eingesetzt werden kann. Die numerische Simulation eröffnet neue, bisher wenig beachtete Möglichkeiten zur Untersuchung komplexer Holzstrukturen sowie Anschlussdetails und wird sich auf Grund der Aussagekraft und Flexibilität auch im Ingenieurholzbau mehr und mehr gegenüber ausschließlich experimenteller Untersuchung durchsetzen.
Re-examination of the behaviour of structures can be necessary due to deterioration or changes in the traffic situation during their lifetime. The Finite Element Method (FEM) is widely used in order to accomplish numerical analysis. Considering the development of computer performance, more detailed FEM models can be analyzed, even on site, with mobile computers. To compensate the increasing amount of data needed for the model input, measures need to be taken to save time, by distributing the work. In order to provide consistency to the model, fedback data must be checked upon reception. A local wireless computer network of ultra-portable devices linked together with a computer can provide the coordination necessary for efficient parallel working. Based on a digital model consisting of all data gathered, structural modelling and numerical analysis are performed automatically. Thus, the user is released from the work that can be automatized and the time needed for the overall analysis of a structure is decreased.
Physically Based Modeling and Multi-Physical Simulation System for Wood Structure Fire Performance
(2004)
This research is devoted to promoting the performance-based engineering in wood structure fire. It looks into the characteristic of the material, structural composing and collapse detecting to find out the main factors in the wood structure collapse in fire. The aim of the research is to provide an automatic simulation platform for the complicated circulation. A physically based model for slim member for beams and columns and a frame of multi-physical simulation are provided to implement the system. The physically based model contains material model, structural mechanics model, material mechanics model, as well as geometry model for the compositive simulation. The multi-physical simulation is built on the model and has the capacity to carry out a simulation combining structural, fire (thermal, CFD) and material degradation simulation. The structural and fire simulation rely on two sophisticated software respectively, ANSYS (an FEA software) and FDS (with a core of CFD). Researchers of the paper develop system by themselves to combine the two existing ones. The system has the capability to calculate the wood char to find out the loss of cross-section and to detect the collapse caused in different ways. The paper gives a sample of Chinese traditional house to show how this simulation system works.
Der vorliegende Beitrag beschreibt die Problematik bei der Prognose verkehrsbedingter Schadstoff-Immissionen. Im Mittelpunkt steht die Entwicklung und der Aufbau einer Simulationsumgebung zur Evaluation von umweltorientierten Verkehrsmanagement-Strategien. Die Simulationsumgebung wird über die drei Felder Verkehr, Emission, Immission entwickelt und findet zunächst Anwendung in der Evaluation verkehrlicher Maßnahmen für die Friedberger Landstraße in Frankfurt am Main.
We present a software prototype for fluid flow problems in civil engineering, which combines essential features of Computational Steering approaches with efficient methods for model transfer and high performance computing. The main components of the system are described: - The modeler with a focus on the data management of the product model - The pre-processing and the post-processing toolkit - The simulation kernel based on the Lattice Boltzmann method - The required hardware for real-time computing
The increasing success of BIM (Building Information Model) and the emergence of its implementation in 3D construction models have paved a way for improving scheduling process. The recent research on application of BIM in scheduling has focused on quantity take-off, duration estimation for individual trades, schedule visualization, and clash detection.
Several experiments indicated that the lack of detailed planning causes about 30% non-productive time and stacking of trades. However, detailed planning still has not been implemented in practice despite receiving a lot of interest from researchers. The reason is associated with the huge amount and complexity of input data. In order to create a detailed planning, it is time consuming to manually decompose activities, collect and calculate the detailed information in relevant. Moreover, the coordination of detailed activities requires much effort for dealing with their complex constraints.
This dissertation aims to support the generation of detailed schedules from a rough schedule. It proposes a model for automated detailing of 4D schedules by integrating BIM, simulation and Pareto-based optimization.
Urban and building energy simulation models are usually driven by typical meteorological year (TMY) weather data often in a TMY2 or EPW format. However, the locations where these historical datasets were collected (usually airports) generally do not represent the local, site specific micro-climates that cities develop. In this paper, a humid sub-tropical climate context has been considered. An idealised “urban unit model” of 250 m radius is being presented as a method of adapting commonly available weather data files to the local micro-climate. This idealised “urban unit model” is based on the main thermal and morphological characteristics of nine sites with residential/institutional (university) use in Hangzhou, China. The area of the urban unit was determined by the region of influence on the air temperature signal at the centre of the unit. Air temperature and relative humidity were monitored and the characteristics of the surroundings assessed (eg green-space, blue-space, built form). The “urban unit model” was then implemented into micro-climatic simulations using a Computational Fluid Dynamics – Surface Energy Balance analysis tool (ENVI-met, Version 4). The “urban unit model” approach used here in the simulations delivered results with performance evaluation indices comparable to previously published work (for air temperature; RMSE <1, index of agreement d > 0.9). The micro-climatic simulation results were then used to adapt the air temperature and relative humidity of the TMY file for Hangzhou to represent the local, site specific morphology under three different weather forcing cases, (ie cloudy/rainy weather (Group 1), clear sky, average weather conditions (Group 2) and clear sky, hot weather (Group 3)). Following model validation, two scenarios (domestic and non-domestic building use) were developed to assess building heating and cooling loads against the business as usual case of using typical meteorological year data files. The final “urban weather projections” obtained from the simulations with the “urban unit model” were used to compare the degree days amongst the reference TMY file, the TMY file with a bulk UHI offset and the TMY file adapted for the site-specific micro-climate (TMY-UWP). The comparison shows that Heating Degree Days (HDD) of the TMY file (1598 days) decreased by 6 % in the “TMY + UHI” case and 13 % in the “TMY-UWP” case showing that the local specific micro-climate is attributed with an additional 7 % (ie from 6 to 13 %) reduction in relation to the bulk UHI effect in the city. The Cooling Degree Days (CDD) from the “TMY + UHI” file are 17 % more than the reference TMY (207 days) and the use of the “TMY-UWP” file results to an additional 14 % increase in comparison with the “TMY + UHI” file (ie from 17 to 31 %). This difference between the TMY-UWP and the TMY + UHI files is a reflection of the thermal characteristics of the specific urban morphology of the studied sites compared to the wider city. A dynamic thermal simulation tool (TRNSYS) was used to calculate the heating and cooling load demand change in a domestic and a non-domestic building scenario. The heating and cooling loads calculated with the adapted TMY-UWP file show that in both scenarios there is an increase by approximately 20 % of the cooling load and a 20 % decrease of the heating load. If typical COP values for a reversible air-conditioning system are 2.0 for heating and 3.5 for cooling then the total electricity consumption estimated with the use of the “urbanised” TMY-UWP file will be decreased by 11 % in comparison with the “business as usual” (ie reference TMY) case. Overall, it was found that the proposed method is appropriate for urban and building energy performance simulations in humid sub-tropical climate cities such as Hangzhou, addressing some of the shortfalls of current simulation weather data sets such as the TMY.
Für eine Abschätzung des Heizwärmebedarfs von Gebäuden und Quartieren können thermisch-energetische Simulationen eingesetzt werden. Grundlage dieser Simulationen sind geometrische und physikalische Gebäudemodelle. Die Erstellung des geometrischen Modells erfolgt in der Regel auf Basis von Bauplänen oder Vor-Ort-Begehungen, was mit einem großen Recherche- und Modellierungsaufwand verbunden ist. Spätere bauliche Veränderungen des Gebäudes müssen häufig manuell in das Modell eingearbeitet werden, was den Arbeitsaufwand zusätzlich erhöht. Das physikalische Modell stellt die Menge an Parametern und Randbedingungen dar, welche durch Materialeigenschaften, Lage und Umgebungs-einflüsse gegeben sind. Die Verknüpfung beider Modelle wird innerhalb der entsprechenden Simulations-software realisiert und ist meist nicht in andere Softwareprodukte überführbar. Mithilfe des Building Information Modeling (BIM) können Simulationsdaten sowohl konsistent gespeichert als auch über Schnittstellen mit entsprechenden Anwendungen ausgetauscht werden. Hierfür wird eine Methode vorgestellt, die thermisch-energetische Simulationen auf Basis des standardisierten Übergabe-formats Industry Foundation Classes (IFC) inklusive anschließender Auswertungen ermöglicht. Dabei werden geometrische und physikalische Parameter direkt aus einem über den gesamten Lebenszyklus aktuellen Gebäudemodell extrahiert und an die Simulation übergeben. Dies beschleunigt den Simulations-prozess hinsichtlich der Gebäudemodellierung und nach späteren baulichen Veränderungen. Die erarbeite-te Methode beruht hierbei auf einfachen Modellierungskonventionen bei der Erstellung des Bauwerksinformationsmodells und stellt eine vollständige Übertragbarkeit der Eingangs- und Ausgangswerte sicher.
Thermal building simulation based on BIM-models. Thermal energetic simulations are used for the estimation of the heating demand of buildings and districts. These simulations are based on building models containing geometrical and physical information. The creation of geometrical models is usually based on existing construction plans or in situ assessments which demand a comparatively big effort of investigation and modeling. Alterations, which are later applied to the structure, request manual changes of the related model, which increases the effort additionally. The physical model represents the total amount of parameters and boundary conditions that are influenced by material properties, location and environmental influences on the building. The link between both models is realized within the correspondent simulation soft-ware and is usually not transferable to other software products. By Applying Building Information Modeling (BIM) simulation data is stored consistently and an exchange to other software is enabled. Therefore, a method which allows a thermal energetic simulation based on the exchange format Industry Foundation Classes (IFC) including an evaluation is presented. All geometrical and physical information are extracted directly from the building model that is kept up-to-date during its life cycle and transferred to the simulation. This accelerates the simulation process regarding the geometrical modeling and adjustments after later changes of the building. The developed method is based on simple conventions for the creation of the building model and ensures a complete transfer of all simulation data.
Für eine Abschätzung des Heizwärmebedarfs von Gebäuden und Quartieren können thermisch-energetische Simulationen eingesetzt werden. Grundlage dieser Simulationen sind geometrische und physikalische Gebäudemodelle. Die Erstellung des geometrischen Modells erfolgt in der Regel auf Basis von Bauplänen oder Vor-Ort-Begehungen, was mit einem großen Recherche- und Modellierungsaufwand verbunden ist. Spätere bauliche Veränderungen des Gebäudes müssen häufig manuell in das Modell eingearbeitet werden, was den Arbeitsaufwand zusätzlich erhöht. Das physikalische Modell stellt die Menge an Parametern und Randbedingungen dar, welche durch Materialeigenschaften, Lage und Umgebungs-einflüsse gegeben sind. Die Verknüpfung beider Modelle wird innerhalb der entsprechenden Simulations-software realisiert und ist meist nicht in andere Softwareprodukte überführbar.
Mithilfe des Building Information Modeling (BIM) können Simulationsdaten sowohl konsistent gespeichert als auch über Schnittstellen mit entsprechenden Anwendungen ausgetauscht werden. Hierfür wird eine Methode vorgestellt, die thermisch-energetische Simulationen auf Basis des standardisierten Übergabe-formats Industry Foundation Classes (IFC) inklusive anschließender Auswertungen ermöglicht. Dabei werden geometrische und physikalische Parameter direkt aus einem über den gesamten Lebenszyklus aktuellen Gebäudemodell extrahiert und an die Simulation übergeben. Dies beschleunigt den Simulations-prozess hinsichtlich der Gebäudemodellierung und nach späteren baulichen Veränderungen. Die erarbeite-te Methode beruht hierbei auf einfachen Modellierungskonventionen bei der Erstellung des Bauwerksinformationsmodells und stellt eine vollständige Übertragbarkeit der Eingangs- und Ausgangswerte sicher.
Thermal building simulation based on BIM-models. Thermal energetic simulations are used for the estimation of the heating demand of buildings and districts. These simulations are based on building models containing geometrical and physical information. The creation of geometrical models is usually based on existing construction plans or in situ assessments which demand a comparatively big effort of investigation and modeling. Alterations, which are later applied to the structure, request manual changes of the related model, which increases the effort additionally. The physical model represents the total amount of parameters and boundary conditions that are influenced by material properties, location and environmental influences on the building. The link between both models is realized within the correspondent simulation soft-ware and is usually not transferable to other software products.
By Applying Building Information Modeling (BIM) simulation data is stored consistently and an exchange to other software is enabled. Therefore, a method which allows a thermal energetic simulation based on the exchange format Industry Foundation Classes (IFC) including an evaluation is presented. All geometrical and physical information are extracted directly from the building model that is kept up-to-date during its life cycle and transferred to the simulation. This accelerates the simulation process regarding the geometrical modeling and adjustments after later changes of the building. The developed method is based on simple conventions for the creation of the building model and ensures a complete transfer of all simulation data.