Universitätsbibliothek
Weimar Open Access

A dynamic XFEM formulation for crack identification

Thermo-hydro-mechanische 3-D-Simulation von Staumauern‐Modellierung und Validierung

Lithium-ion (Li-ion) batteries are currently considered as vital components for advances in mobile technologies such as those in communications and transport. Nonetheless, Li-ion batteries suffer from temperature rises which sometimes lead to operational damages or may even cause fire. An appropriate solution to control the temperature changes during the operation of Li-ion batteries is to embed batteries inside a paraffin matrix to absorb and dissipate heat. In the present work, we aimed to investigate the possibility of making paraffin nanocomposites for better heat management of a Li-ion battery pack. To fulfill this aim, heat generation during a battery charging/discharging cycles was simulated using Newman’s well established electrochemical pseudo-2D model. We couple this model to a 3D heat transfer model to predict the temperature evolution during the battery operation. In the later model, we considered different paraffin nanocomposites structures made by the addition of graphene, carbon nanotubes, and fullerene by assuming the same thermal conductivity for all fillers. This way, our results mainly correlate with the geometry of the fillers. Our results assess the degree of enhancement in heat dissipation of Li-ion batteries through the use of paraffin nanocomposites. Our results may be used as a guide for experimental set-ups to improve the heat management of Li-ion batteries.

Problem definition and research objectives 1. The production of Portland cement clinker causes approx. 5% to 8% of the annual man-made CO2 emissions. This is due to the usage of mainly fossil fuel (approx. 40 % of the total CO2) and because of the decarbonation of limestone as a main component of the raw meal (approx. 60 % of the total CO2). 2. Various strategies are applied in order to reduce the green-house gas-emissions, such as optimizing the process of clinker production, the use of alternative fuel and the partial substitution of the clinker in blended cement by so-called SCM (supplementary cementitious materials). Hereby blast-furnace slag, fly ash and limestone are the most used materials. 3. Quaternary systems containing three SCM simultaneously besides Portland cement contribute to the reduction of CO2 emissions due to the decrease of the clinker content. In addition, such systems allow to use blast-furnace slag and fly ash in the most economical way and provide the possibility to account for shortages of SCM on the market. 4. Blast-furnace slag and fly ash show similarities in their principal chemical compositions such that similar hydrates are formed during their reaction in presence of Portland cement. Compared to ternary systems based on blast-furnace slag or fly ash besides limestone, quaternary systems that contain both, blast-furnace slag and fly ash, simultaneously besides limestone, are expected to perform similar in terms of phase assemblage and strength development. 5. The use of SCM as cement replacing materials is limited due to their generally slower reaction compared to neat cement which also leads to lower strength development, especially in the early stage of the hydration up to 28 d. To account for this it is necessary to study the reactivity of SCM such as blast-furnace slag and fly ash in detail in order to develop strategies to enhance the reactivity and thereby the strength development of SCM-containing systems. 6. The early hydration of clinker phases is studied in detail, mainly in diluted systems. It is unclear if processes that were found to control the reaction of such model systems are also prevailing in concentrated cement pastes under realistic water-to-solid ratios. Deeper insight to this aspect is needed to better understand interactions of neat Portland cement and SCM in the first hours of hydration. State-of-the-art 7. Increasing Ca-concentrations lead to decreasing dissolution rates of C3S and C2S in diluted systems. 8. The hydration kinetics of C3S is controlled by the interplay of undersaturation with respect to C3S and oversaturation with respect to C-S-H. 9. Increasing Al-concentrations lead to a retardation of the hydration of C3S. It is unclear if the uptake of aluminum in C-S-H to form C-(A)-S-H which has a significantly lower growth rate than pure C-S-H or a retarding effect of Al on the dissolution of C3S causes this phenomenon. 10. The surface of limestone provides excellent conditions for the nucleation and growth of C-S-H such that significantly more C-S-H nuclei are formed in presence of limestone compared to other SCM. 11. The reactivity of blast-furnace slag and fly ash depends on the particle size as well as on the intrinsic reactivity of especially the amorphous phases. 12. An increase in network modifying oxides (e.g. CaO) in the chemical composition of amorphous (calcium)aluminosilicates leads to an increasingly depolymerized network which in turn causes increasing reactivity. The role of amphoteric oxides (Al2O3, Fe2O3) that can be present as network modifying oxides as well as network forming oxides is not completely solved. 13. CO2-containing AFm-phases are thermodynamically more stable than monosulfoaluminate. This indirectly stabilizes the voluminous ettringite which causes a higher total volume of hydrates and lower porosity whereby higher compressive strength is reached. 14. Only a few percent of limestone in blended cement reacts chemically dependent on the Al2O3 available for reaction. Al2O3 that is provided by the reaction of Portland cement but also by the dissolution of SCM, especially by fly ash, reacts to form hemicarboaluminate which is transformed to monocarboaluminate as the hydration proceeds. Methodology 15. The influence of SCM on the early hydration of Portland cement in binary (including blast-furnace slag or fly ash or limestone or quartz) and ternary (including fly ash and limestone) systems was investigated applying isothermal calorimetry and analysis of the pore solution chemistry. Calculated saturation indices and solubility products of relevant phases were correlated with heat development. Based on the gained data it was reviewed if mechanisms that control the hydration of pure phases in diluted systems are also prevailing in cement pastes under realistic conditions. 16. The influence of the chemical composition of synthetic glasses on their dissolution at high pH was investigated in highly diluted systems using ion chromatography. Pozzolanity tests were conducted on pastes using simplified model systems and glass-blended Portland cements. The process of the glass dissolution was investigated by isothermal calorimetry and by thermogravimetry. Correlation of experimentally determined total bound water with bound water determined by mass balance calculations as a function of amount of glass reacted allowed to estimate the degree of glass reaction in the pastes. Further on selective dissolution experiments were carried out to crosscheck the results of the bound water/mass balance approach. 17. The reaction kinetics of quaternary pastes containing blast-furnace slag and fly ash simultaneously in the presence of limestone were investigated up to 28 d using isothermal calorimetry and chemical shrinkage measurements. In addition strength tests on mortar bars were carried out. 18. Pastes of quaternary blends were also investigated in terms of hydrate assemblage at ages of up to 182 d. Thermodynamic calculations regarding total volume of hydrates as a function of limestone and fly ash/blast-furnace slag content were conducted. The calculations were supported by thermogravimetric determination of bound water and portlandite content as well as qualitative X-ray diffraction. The results were correlated with strength tests on mortar bars. 19. The pore solutions of hydrated quaternary blends were extracted and investigated by means of ion chromatography at ages of up to 728 d. Based on the ion concentrations in the solutions saturation indices were calculated for relevant phases. In order to gain better insight to the blast-furnace slag reaction sulphate speciation was carried out at two blast furnace slag levels (20 and 30 wt.%) for selected samples up to 91 d of hydration and at 91 d for the whole matrix under investigation. Main results 20. Investigations on the early hydration kinetics of binary systems showed a higher heat flow in presence of SCM compared to neat Portland cement. This is caused by the higher surface area that is available for the nucleation of hydrates and by the lower (over)saturation with respect to C-S-H. An increase in the Ca-concentration in the pore solution did not cause lower dissolution rates of C3S as was reported for pure phases in diluted systems. The highest dissolution was observed in the presence of limestone, i.e. at the highest Ca-concentration. The general trend of the reaction rate is inversely related to the degree of undersaturation with respect to C3S. The more undersaturated the faster the observed reaction. The presence of increasing Al-concentrations caused a retardation of the reaction which is in line with investigations on pure phases in diluted systems. Higher sulphate concentrations could be detected for the fly ash containing blend which possibly hindered ettringite precipitation and results in higher Al-concentrations. Correspondingly the low sulphate concentrations lead to lower Al-concentrations in the presence of quartz, blast-furnace slag and limestone compared to fly ash. 21. The early hydration kinetics of quaternary systems is significantly accelerated in the presence of limestone while fly ash leads to retardation. Compared to reference systems containing inert quartz, investigations by means of isothermal calorimetry and chemical shrinkage revealed an acceleration caused by blast-furnace slag. Additions of fly ash, limestone or mixtures thereof introduced another acceleration but differences are too small to be significant and clear distinguishing between the various SCM is not possible. 22. Investigations on the reactivity of synthetic glasses showed that increasing amounts of network modifying oxides caused an increase in reactivity and dissolution rates. The results reveal that Al2O3 acts mainly as network modifying oxide in all investigated glasses. Experimentally determined bound water (thermogravimetric experiments) in model systems and blended cements can be compared with bound water determined by mass balance calculations carried out as a function of the amount of glass reacted. This enables to estimate the degree of glass reaction. 23. The actual content of blast-furnace slag, fly ash or limestone does not exert significant influence on the development of compressive strength up to 7 d. At later ages thermodynamic calculations predict a degree of CaCO3 reaction of 2 to 5 wt.%. This leads to the formation of hemicarbonate and monocarbonate whereby ettringite is indirectly stabilized. As a result the total amount of solids is increased and compressive strength shows a slight maximum. Hereby the degree of CaCO3 reaction depends on the Al2O3 available for reaction which is not only provided by the dissolution of Portland cement but especially by the dissolution of the fly ash. 24. In general the presence of blast-furnace slag and fly ash in the presence of limestone exerts little influence on the hydrate assemblage. The substitution of some of the blast-furnace slag by fly ash leads to a slight decrease of portlandite and C-S-H and gives rise to the formation of more monocarbonate and hemicarbonate. Portlandite is consumed in a pozzolanic reaction with the fly ash whereby C-S-H is formed. However, the low reactivity of the fly ash causes a decrease in the amount of C-S-H formed. Thereby a lower total volume of hydrates is generated which is in line with slightly lower compressive strength in case of increasing fly ash content. The overall influence is small and all systems investigated reach strength class 42.5 N according to EN 196-1. 25. Corresponding to the investigations of the hydrate assemblage the pore solution chemistry of quaternary systems showed only small variations. Depending on the fly ash content the highest variations are observed for aluminium, i.e. increasing fly ash content leads to higher Al-concentrations. Another effect of increasing fly ash contents is an increasing undersaturation with respect to portlandite and a decreasing undersaturation with respect to strätlingite indicating the dissolution of portlandite. 26. The total concentration of sulfur in the pore solution is controlled by sulphate (SO42–) while the concentrations of sulphite (SO32–) and thiosulphate (S2O32–) were very low. Up to 2 d of hydration about 90 % of the total sulphur is present as SO42–. After 91 d this value is reduced to about 36 % while about 28 % are present as S2O32–. In general higher blast-furnace slag content leads to higher concentrations of sulphite and thiosulphate after 7 d.

Die Dissertation über „Ambiguität im zeitgenössischen Film – Flugversuche“ folgt der Spur einer populären narrativen Tendenz im Kino – nämlich der Mehrdeutigkeit – und zeichnet ihr dramaturgisches Potential, wie ihre ethischen (bzw. mikropolitischen) Implikationen nach. Um typische Muster in der Wahrnehmung mehrdeutiger Filmerzählungen zu beschreiben, die bereits auf der vorbewussten Ebene der Affekte wirksam sind, greife ich auf Begriffe der Prozessphilosophie Alfred North Whitehead’s zurück und auf ihre neueren Reformulierungen bei Gilles Deleuze und Brian Massumi. Ausgehend von Alejandro González Iñárritu’s "Babel" (2006) begibt sich der Leser im ersten Teil auf einen virtuellen Rundflug durch ausgewählte Filmbeispiele mit einem kulturellen Ankerpunkt im heutigen Japan. Im zweiten Teil beschreibe und reflektiere ich mein methodisches Vorgehen in den ersten Phasen der Stoffentwicklung zu einem suggestiven Spielfilmprojekt, und kontextualisiere es mit Interviews zeitgenössischer Autorenfilmer, die ähnliche Erzählweisen entwickeln.

The objective of the investigations was the proof of the use of the neutral salt initiation as a construction material in the protecting silicate coating of concrete components, e.g. factory finished parts or reinforced concrete construction parts, by means of waterglass fused silica suspensions

The phenomenon of aerodynamic instability caused by the wind is usually a major design criterion for long-span cable-supported bridges. If the wind speed exceeds the critical flutter speed of the bridge, this constitutes an Ultimate Limit State. The prediction of the flutter boundary, therefore, requires accurate and robust models. The complexity and uncertainty of models for such engineering problems demand strategies for model assessment. This study is an attempt to use the concepts of sensitivity and uncertainty analyses to assess the aeroelastic instability prediction models for long-span bridges. The state-of-the-art theory concerning the determination of the flutter stability limit is presented. Since flutter is a coupling of aerodynamic forcing with a structural dynamics problem, different types and classes of structural and aerodynamic models can be combined to study the interaction. Here, both numerical approaches and analytical models are utilised and coupled in different ways to assess the prediction quality of the coupled model.

The described study aims to find correlations between urban spatial configurations and human emotions. To this end, the authors measured people’s emotions while they walk along a path in an urban area using an instrument that measures skin conductance and skin temperature. The corresponding locations of the test persons were measured recorded by using a GPS-tracker (n=13). The results are interpreted and categorized as measures for positive and negative emotional arousal. To evaluate the technical and methodological process. The test results offer initial evidence that certain spaces or spatial sequences do cause positive or negative emotional arousal while others are relatively neutral. To achieve the goal of the study, the outcome was used as a basis for the study of testing correlations between people’s emotional responses and urban spatial configurations represented by Isovist properties of the urban form. By using their model the authors can explain negative emotional arousal for certain places, but they couldn’t find a model to predict emotional responses for individual spatial configurations.

Previous publications about biochar in anaerobic digestion show encouraging results with regard to increased biogas yields. This work investigates such effects in a solid-state fermentation of bio-waste. Unlike in previous trials, the influence of biochar is tested with a setup that simulates an industrial-scale biogas plant. Both the biogas and the methane yield increased around 5% with a biochar addition of 5%-based on organic dry matter biochar to bio-waste. An addition of 10% increased the yield by around 3%. While scaling effects prohibit a simple transfer of the results to industrial-scale plants, and although the certainty of the results is reduced by the heterogeneity of the bio-waste, further research in this direction seems promising.

In vielen öffentlichen Gebäuden besteht ein hohes wirtschaftliches Einsparpotenzial bei den relevanten Energieträgern Wärme und Strom. Projekte zur energetischen Optimierungen refinanzieren sich häufig nach wenigen Jahren. Die notwenigen Investitionsmittel stehen jedoch nur begrenzt zur Verfügung. Zielgerichtete Analysen und Potenzialschätzungen sind erforderlich, um eine Priorisierung optionaler Maßnahmen zu erreichen. Die Studie zeigt anhand eines öffentlichen Portfolios notwendige Untersuchungsschritte auf. Die Einzelpotenziale werden über geeignete Benchmarks ermittelt. Auf Portfolioebene werden u. a. spezifische Potenzial-Matrizen genutzt. Die kennzahlenbasierte Priorisierung von Maßnahmen ist umso wichtiger, je stärker das Potenzial auf wenige Objekte konzentriert ist.