### Refine

#### Has Fulltext

- yes (16) (remove)

#### Document Type

- Article (16) (remove)

#### Institute

#### Keywords

- Modellierung (16) (remove)

A coupled thermo-hydro-mechanical model of jointed hard rock for compressed air energy storage
(2014)

Renewable energy resources such as wind and solar are intermittent, which causes instability when being connected to utility grid of electricity. Compressed air energy storage (CAES) provides an economic and technical viable solution to this problem by utilizing subsurface rock cavern to store the electricity generated by renewable energy in the form of compressed air. Though CAES has been used for over three decades, it is only restricted to salt rock or aquifers for air tightness reason. In this paper, the technical feasibility of utilizing hard rock for CAES is investigated by using a coupled thermo-hydro-mechanical (THM) modelling of nonisothermal gas flow. Governing equations are derived from the rules of energy balance, mass balance, and static equilibrium. Cyclic volumetric mass source and heat source models are applied to simulate the gas injection and production. Evaluation is carried out for intact rock and rock with discrete crack, respectively. In both cases, the heat and pressure losses using air mass control and supplementary air injection are compared.

Flow velocity is generally presumed to influence flood damage. However, this influence is hardly quantified and virtually no damage models take it into account. Therefore, the influences of flow velocity, water depth and combinations of these two impact parameters on various types of flood damage were investigated in five communities affected by the Elbe catchment flood in Germany in 2002. 2-D hydraulic models with high to medium spatial resolutions were used to calculate the impact parameters at the sites in which damage occurred. A significant influence of flow velocity on structural damage, particularly on roads, could be shown in contrast to a minor influence on monetary losses and business interruption. Forecasts of structural damage to road infrastructure should be based on flow velocity alone. The energy head is suggested as a suitable flood impact parameter for reliable forecasting of structural damage to residential buildings above a critical impact level of 2m of energy head or water depth. However, general consideration of flow velocity in flood damage modelling, particularly for estimating monetary loss, cannot be recommended.

The paper gives the results of scientific research, which, being based on probabilistic and statistical modeling, identifies the relationship of certain socio-economic factors and the number of people killed in road accidents in the Russian Federation regions. It notes the identity of processes in various fields, in which there is loss of life. Scientific methods and techniques were used in the process of data processing and study findings: systematic approach, methods of system analysis (algorithmization, mathematical programming) and mathematical statistics. The scientific novelty lies in the formulation, formalization and solving problems related to the analysis of regional road traffic accidents, its modeling taking into account the factors of socio-economic impact.

Model of stressed-strained State of Multilayer Masses with regard for Non-Ideal Contact of Layers
(1997)

Thus, mathematical model stressed- strained of a condition of layered masses is constructed. The model has high accuracy. It allows to simulate slippery contact of layers without friction. Thus not the order of permitting system of the equations is increased, and at its realization the method of fenite elements does not increase quantity of required degrees freedom. The differential operators included in system the equations are similar known in the classical theory of shells. It facilitates construction of a finite element. Presence in system of the differential equations of derivative of external forces allows to use her for the decision of contact problems with a stain of contact commensurable with thickness of a masses.

The effectiveness of working processes accomplished by various technological machines to a large extend depends on working quality of supply, transporting and orientating mechanisms which are very often produced as positional hydro-mechanical systems. The choice of their best type and regimes of work requires construction and analysis of models of their optimum steering which are complicated by nonlinearness, multy-criterialness of problem and also by occasional outbreaks of parameters and moments of steering regime changing. It was developed the common structure of such systems allowing within common scheme to vary the complexity degree of PHMS and the methods of inhibitory efforts supplement. For some systems which are complicated in series (from two-measured linear system to nine-measured non-linear) puzzles of the most fast zero-ambit getting are solved and two-criterial problems are analyzed. (T-min-speed, Z(T)- accuracy). There are suggested the computing procedures of optimum PHMS synthesis. The effectiveness of accepted methods of solving is asserted by the analogy of the results of gradually complicated models investigation and by their good analogy with the natural experiment. It was exposed the sense of heuristic methods of improving of approximately optimum steering, their elaboration on the base of theoretical models. The basic methods of optimum PGMS construction were also nominated.

The purpose of this paper is to review model for finite element techniques for non-linear crack analysis of reinforced concrete beams and slabs. The non-linear behaviour of concrete and steel were described. Some calculations of >self-stress< for concrete and reinforced concrete beam was made. Current computational aspects are discussed. Several remarks for future studies are also given. The numerical model of the concrete and reinforced concrete was described. The paper shows the results of calculations on a reinforced concrete plane stress panel with cracks. The non-linear, numerical model of calculations of reinforced concrete was assumed. Using finite elements method some calculations were made. The results of calculations like displacements, stresses and cracking are shown on diagrams. They were compared with experimental results and other finding. Some conclusions about the described model and results of calculation are shown.

In the given paper the generalized formulation of the problem of computer modelling of the complex-composite structure interaction with different types of dynamic loads and effects is discussed. Here the analysis is given as for the usage of some universal computing systems for the solution of such problems. Also if is shown that the quantification of the dynamic models of the complex-composite systems with the variable structure, depending on the character and intensivity of the effects, is necessary. The different variants of the joint and the space structure element modelling are gested. It allows to consider the complex modes of the joint bending-torsional oscillations of such structures as bridges, towers, high-rise buildings. The peculiarities of the modelling and testing of some problems of the objects aerodynamics and the interaction of the frameworks constructions with shock and movable loads are considered. In this paper the examples of the complex-composite structure dynamic analysis are shown. It is achieved by means of some special methods of the input of the real inducements and loads of the exploitated analog-object into the computing model. The suggested models found a wide use both at the design of new structures and the dynamic monitoring of the exploitated structures.

There is an increasing need for 3D building extraction from aerial images for various applications such astown planning, environmental- and property-related studies. Aerial images usually reveal on one hand a certain amount of information not relevant for the given task of building extraction like vegetation, cars etc. On the other hand there is a loss of relevant information due to occlusions, low contrasts or disadvantageous perspectives. Therefore a promising concept for automated building reconstruction must incorporate a suffciantly complete model of the objects of interest. We propose a model-based approach to 3D building extraction from aerial images which reveals a tight coupling between a generic 3D object model and an explicit 2D image model. The generic object model employes domain specific volumetric primitives (i. e. building part models) and combination schemes. To cover the gap between 3D object models and 2D image data the image model is employed to predict the projective building appearences in aerial images. We present a strategy for a model-based building extraction based on the recognition-by-components principle and show first experimental results derived from international test sets

Essence of service unreliability on account of irregularity has been given. The reasons of occurance of overcrowded vehicles have been listed. The factor of service unreliability on account of irregularity has been determined. It is probability of the event, that the passenger finds departing vehicle fully filled, i.e. when all places seating and standing are occupied or condition of the travel, which would be not acceptable for passenger. Large dispersion of headways (i.e. irregularity) increases probability of such situations. To calculate the mentioned factor, the computer simulation was used. Both, passenger arrivals and vehicle operation have been modelled as stochastic interacted processes. Distributions of headways and passenger arrivals have been fixed by statistical methods. The >maximal capacity< of a vehicle has been determined. The set of parameters values for simulation runs has been given. The transformed results of computer simulation are series of nomographs for determination of a factor value. They were prepared for many types of trams and city buses, but only one nomograph has been presented. Difficulties in verification of model were discussed. Recommendations for rational utilisation level of public transport means capacity in the condition of randomness of passenger arrivals and disturbances in vehicle operation have been proposed. The other possibilities of service unreliability have been mentioned. General conclusions have been given

Die Zielstellung der ModalSplitBetrachtungen läuft darauf hinaus, Entscheidungs-kriterien zu erarbeiten, nach denen die einzelnen Personen ihre Verkehrsmittel auswählen. In dieser Veröffentlichung wurden alle drei Gruppen der Modelle (klassische, verhaltensorientierte und der Analyse) der Verkehrsaufteilung kurz charakterisiert. Dann wurden vier ausgewählte Modelle genauer beschrieben. Zum Schluß wird das Modell der Verkehrsmittelwahl dargestellt , das für die Untersuchung der Verkehrsaufteilung in Krakau verwendet wurde .