TY - JOUR A1 - Nabipour, Narjes A1 - Dehghani, Majid A1 - Mosavi, Amir A1 - Shamshirband, Shahaboddin T1 - Short-Term Hydrological Drought Forecasting Based on Different Nature-Inspired Optimization Algorithms Hybridized With Artificial Neural Networks JF - IEEE Access N2 - Hydrological drought forecasting plays a substantial role in water resources management. Hydrological drought highly affects the water allocation and hydropower generation. In this research, short term hydrological drought forecasted based on the hybridized of novel nature-inspired optimization algorithms and Artificial Neural Networks (ANN). For this purpose, the Standardized Hydrological Drought Index (SHDI) and the Standardized Precipitation Index (SPI) were calculated in one, three, and six aggregated months. Then, three states where proposed for SHDI forecasting, and 36 input-output combinations were extracted based on the cross-correlation analysis. In the next step, newly proposed optimization algorithms, including Grasshopper Optimization Algorithm (GOA), Salp Swarm algorithm (SSA), Biogeography-based optimization (BBO), and Particle Swarm Optimization (PSO) hybridized with the ANN were utilized for SHDI forecasting and the results compared to the conventional ANN. Results indicated that the hybridized model outperformed compared to the conventional ANN. PSO performed better than the other optimization algorithms. The best models forecasted SHDI1 with R2 = 0.68 and RMSE = 0.58, SHDI3 with R 2 = 0.81 and RMSE = 0.45 and SHDI6 with R 2 = 0.82 and RMSE = 0.40. KW - Maschinelles Lernen KW - Machine learning KW - Deep learning KW - Hydrological drought KW - precipitation KW - hydrology Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200213-40796 UR - https://ieeexplore.ieee.org/document/8951168 VL - 2020 IS - volume 8 SP - 15210 EP - 15222 PB - IEEE ER - TY - THES A1 - Oucif, Chahmi T1 - Analytical Modeling of Self-Healing and Super Healing in Cementitious Materials N2 - Self-healing materials have recently become more popular due to their capability to autonomously and autogenously repair the damage in cementitious materials. The concept of self-healing gives the damaged material the ability to recover its stiffness. This gives a difference in comparing with a material that is not subjected to healing. Once this material is damaged, it cannot sustain loading due to the stiffness degradation. Numerical modeling of self-healing materials is still in its infancy. Multiple experimental researches were conducted in literature to describe the behavior of self-healing of cementitious materials. However, few numerical investigations were undertaken. The thesis presents an analytical framework of self-healing and super healing materials based on continuum damage-healing mechanics. Through this framework, we aim to describe the recovery and strengthening of material stiffness and strength. A simple damage healing law is proposed and applied on concrete material. The proposed damage-healing law is based on a new time-dependent healing variable. The damage-healing model is applied on isotropic concrete material at the macroscale under tensile load. Both autonomous and autogenous self-healing mechanisms are simulated under different loading conditions. These two mechanisms are denoted in the present work by coupled and uncoupled self-healing mechanisms, respectively. We assume in the coupled self-healing that the healing occurs at the same time with damage evolution, while we assume in the uncoupled self-healing that the healing occurs when the material is deformed and subjected to a rest period (damage is constant). In order to describe both coupled and uncoupled healing mechanisms, a one-dimensional element is subjected to different types of loading history. In the same context, derivation of nonlinear self-healing theory is given, and comparison of linear and nonlinear damage-healing models is carried out using both coupled and uncoupled self-healing mechanisms. The nonlinear healing theory includes generalized nonlinear and quadratic healing models. The healing efficiency is studied by varying the values of the healing rest period and the parameter describing the material characteristics. In addition, theoretical formulation of different self-healing variables is presented for both isotropic and anisotropic maerials. The healing variables are defined based on the recovery in elastic modulus, shear modulus, Poisson's ratio, and bulk modulus. The evolution of the healing variable calculated based on cross-section as function of the healing variable calculated based on elastic stiffness is presented in both hypotheses of elastic strain equivalence and elastic energy equivalence. The components of the fourth-rank healing tensor are also obtained in the case of isotropic elasticity, plane stress and plane strain. Recent research revealed that self-healing presents a crucial solution also for the strengthening of the materials. This new concept has been termed ``Super Healing``. Once the stiffness of the material is recovered, further healing can result as a strengthening material. In the present thesis, new theory of super healing materials is defined in isotropic and anisotropic cases using sound mathematical and mechanical principles which are applied in linear and nonlinear super healing theories. Additionally, the link of the proposed theory with the theory of undamageable materials is outlined. In order to describe the super healing efficiency in linear and nonlinear theories, the ratio of effective stress to nominal stress is calculated as function of the super healing variable. In addition, the hypotheses of elastic strain and elastic energy equivalence are applied. In the same context, new super healing matrix in plane strain is proposed based on continuum damage-healing mechanics. In the present work, we also focus on numerical modeling of impact behavior of reinforced concrete slabs using the commercial finite element package Abaqus/Explicit. Plain and reinforced concrete slabs of unconfined compressive strength 41 MPa are simulated under impact of ogive-nosed hard projectile. The constitutive material modeling of the concrete and steel reinforcement bars is performed using the Johnson-Holmquist-2 damage and the Johnson-Cook plasticity material models, respectively. Damage diameters and residual velocities obtained by the numerical model are compared with the experimental results and effect of steel reinforcement and projectile diameter is studied. KW - Schaden KW - Beschädigung KW - Selbstheilung KW - Zementbeton KW - Damage KW - Healing KW - Concrete KW - Autonomous KW - Autogenous KW - Super Healing Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200831-42296 ER - TY - THES A1 - Chan, Chiu Ling T1 - Smooth representation of thin shells and volume structures for isogeometric analysis N2 - The purpose of this study is to develop self-contained methods for obtaining smooth meshes which are compatible with isogeometric analysis (IGA). The study contains three main parts. We start by developing a better understanding of shapes and splines through the study of an image-related problem. Then we proceed towards obtaining smooth volumetric meshes of the given voxel-based images. Finally, we treat the smoothness issue on the multi-patch domains with C1 coupling. Following are the highlights of each part. First, we present a B-spline convolution method for boundary representation of voxel-based images. We adopt the filtering technique to compute the B-spline coefficients and gradients of the images effectively. We then implement the B-spline convolution for developing a non-rigid images registration method. The proposed method is in some sense of “isoparametric”, for which all the computation is done within the B-splines framework. Particularly, updating the images by using B-spline composition promote smooth transformation map between the images. We show the possible medical applications of our method by applying it for registration of brain images. Secondly, we develop a self-contained volumetric parametrization method based on the B-splines boundary representation. We aim to convert a given voxel-based data to a matching C1 representation with hierarchical cubic splines. The concept of the osculating circle is employed to enhance the geometric approximation, where it is done by a single template and linear transformations (scaling, translations, and rotations) without the need for solving an optimization problem. Moreover, we use the Laplacian smoothing and refinement techniques to avoid irregular meshes and to improve mesh quality. We show with several examples that the method is capable of handling complex 2D and 3D configurations. In particular, we parametrize the 3D Stanford bunny which contains irregular shapes and voids. Finally, we propose the B´ezier ordinates approach and splines approach for C1 coupling. In the first approach, the new basis functions are defined in terms of the B´ezier Bernstein polynomials. For the second approach, the new basis is defined as a linear combination of C0 basis functions. The methods are not limited to planar or bilinear mappings. They allow the modeling of solutions to fourth order partial differential equations (PDEs) on complex geometric domains, provided that the given patches are G1 continuous. Both methods have their advantages. In particular, the B´ezier approach offer more degree of freedoms, while the spline approach is more computationally efficient. In addition, we proposed partial degree elevation to overcome the C1-locking issue caused by the over constraining of the solution space. We demonstrate the potential of the resulting C1 basis functions for application in IGA which involve fourth order PDEs such as those appearing in Kirchhoff-Love shell models, Cahn-Hilliard phase field application, and biharmonic problems. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2020,2 KW - Modellierung KW - Isogeometrische Analyse KW - NURBS KW - Geometric Modeling KW - Isogeometric Analysis KW - NURBS Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200812-42083 ER - TY - JOUR A1 - Mousavi, Seyed Nasrollah A1 - Steinke Júnior, Renato A1 - Teixeira, Eder Daniel A1 - Bocchiola, Daniele A1 - Nabipour, Narjes A1 - Mosavi, Amir A1 - Shamshirband, Shahaboddin T1 - Predictive Modeling the Free Hydraulic Jumps Pressure through Advanced Statistical Methods JF - Mathematics N2 - Pressure fluctuations beneath hydraulic jumps potentially endanger the stability of stilling basins. This paper deals with the mathematical modeling of the results of laboratory-scale experiments to estimate the extreme pressures. Experiments were carried out on a smooth stilling basin underneath free hydraulic jumps downstream of an Ogee spillway. From the probability distribution of measured instantaneous pressures, pressures with different probabilities could be determined. It was verified that maximum pressure fluctuations, and the negative pressures, are located at the positions near the spillway toe. Also, minimum pressure fluctuations are located at the downstream of hydraulic jumps. It was possible to assess the cumulative curves of pressure data related to the characteristic points along the basin, and different Froude numbers. To benchmark the results, the dimensionless forms of statistical parameters include mean pressures (P*m), the standard deviations of pressure fluctuations (σ*X), pressures with different non-exceedance probabilities (P*k%), and the statistical coefficient of the probability distribution (Nk%) were assessed. It was found that an existing method can be used to interpret the present data, and pressure distribution in similar conditions, by using a new second-order fractional relationships for σ*X, and Nk%. The values of the Nk% coefficient indicated a single mean value for each probability. KW - Maschinelles Lernen KW - Machine learning KW - mathematical modeling KW - extreme pressure KW - hydraulic jump KW - stilling basin KW - standard deviation of pressure fluctuations KW - statistical coeffcient of the probability distribution Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200402-41140 UR - https://www.mdpi.com/2227-7390/8/3/323 VL - 2020 IS - Volume 8, Issue 3, 323 PB - MDPI CY - Basel ER - TY - JOUR A1 - Fathi, Sadegh A1 - Sajadzadeh, Hassan A1 - Mohammadi Sheshkal, Faezeh A1 - Aram, Farshid A1 - Pinter, Gergo A1 - Felde, Imre A1 - Mosavi, Amir T1 - The Role of Urban Morphology Design on Enhancing Physical Activity and Public Health JF - International Journal of Environmental Research and Public Health N2 - Along with environmental pollution, urban planning has been connected to public health. The research indicates that the quality of built environments plays an important role in reducing mental disorders and overall health. The structure and shape of the city are considered as one of the factors influencing happiness and health in urban communities and the type of the daily activities of citizens. The aim of this study was to promote physical activity in the main structure of the city via urban design in a way that the main form and morphology of the city can encourage citizens to move around and have physical activity within the city. Functional, physical, cultural-social, and perceptual-visual features are regarded as the most important and effective criteria in increasing physical activities in urban spaces, based on literature review. The environmental quality of urban spaces and their role in the physical activities of citizens in urban spaces were assessed by using the questionnaire tool and analytical network process (ANP) of structural equation modeling. Further, the space syntax method was utilized to evaluate the role of the spatial integration of urban spaces on improving physical activities. Based on the results, consideration of functional diversity, spatial flexibility and integration, security, and the aesthetic and visual quality of urban spaces plays an important role in improving the physical health of citizens in urban spaces. Further, more physical activities, including motivation for walking and the sense of public health and happiness, were observed in the streets having higher linkage and space syntax indexes with their surrounding texture. KW - Morphologie KW - Gesundheitswesen KW - Intelligente Stadt KW - Nachhaltigkeit KW - Gesundheitsinformationssystem KW - urban morphology KW - public health KW - physical activities KW - health KW - public space KW - urban health KW - smart cities KW - sustainability Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200402-41225 UR - https://www.mdpi.com/1660-4601/17/7/2359 VL - 2020 IS - Volume 17, Issue 7, 2359 PB - MDPI CY - Basel ER - TY - THES A1 - Hoinkis, Jule Hannah T1 - Hitze in der Stadt Jena BT - Eine Untersuchung des städtischen Mikroklimas von Jena, dessen Veränderungen infolge des Klimawandels, städtebaulicher Anpassungsstrategien & Anwendung der Ergebnisse anhand eines städtebaulichen Konzeptes zur Neugestaltung des Bachstraßenareals. N2 - Die vorliegende Arbeit befasst sich mit den spezifischen Faktoren und Wechselwirkungen des städtischen Klimas und Strategien zur Prävention und Kompensation lokaler Klimaveränderungen. Problematische Merkmale des Stadtklimas werden sich infolge des Klimawandels stärker ausprägen. Insbesondere die Hitzebelastung wird zunehmen und die Lebensbedingungen in der Stadt negativ beeinflussen. Infolge höherer Temperaturen in Städten und einer höheren Temperaturdifferenz zum Umland verändern sich Windströme und die Wasserbilanz. Es sind Strategien notwendig, um den Schadstoffausstoß, die Flächeninanspruchnahme, die Abfallproduktion und den Wasser-, Energie- und Ressourcenverbrauch zu verringern, um sowohl langfristig den Klimawandel als auch dessen bereits unvermeidbaren Auswirkungen auf Städte zu begrenzen. Beispielhaft untersucht die Arbeit das Stadtklima, dessen zukünftige Veränderungen infolge des Klimawandels, bauliche Maßnahmen und Anpassungsstrategien der Stadt Jena. Jena ist die zweitgrößte Stadt im Bundesland Thüringen und gehört heute zu den wärmsten und trockensten Großstädten Deutschlands. Die Ergebnisse der Arbeit werden anschließend anhand eines städtebaulichen Konzepts und Entwurfs angewendet. Das Bachstraßenareal liegt in der Innenstadt, dem am stärksten von Hitze betroffenen Stadtteil. Als ehemaliger Hauptstandort des Jenaer Universitätsklinikums, soll es zu einem nachhaltigen Wissenschaftscampus der Lebenswissenschaften umgebaut werden, wobei ein Großteil der denkmalgeschützten, ehemaligen Klinikgebäude erhalten bleibt. Der Fokus liegt dabei auf der Umsetzung der zuvor formulierten, nachhaltigen Strategien zur Verbesserung des lokalen Stadtklimas und einer Abschwächung der Auswirkungen des Klimawandels auf den besonders stark betroffenen Innenstadtbereich Jenas. KW - Hitze KW - Jena KW - Stadtklima KW - Klimawandel Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220414-46323 ER - TY - THES A1 - Alabassy, Mohamed Said Helmy T1 - Automated Approach for Building Information Modelling of Crack Damages via Image Segmentation and Image-based 3D Reconstruction N2 - As machine vision-based inspection methods in the field of Structural Health Monitoring (SHM) continue to advance, the need for integrating resulting inspection and maintenance data into a centralised building information model for structures notably grows. Consequently, the modelling of found damages based on those images in a streamlined automated manner becomes increasingly important, not just for saving time and money spent on updating the model to include the latest information gathered through each inspection, but also to easily visualise them, provide all stakeholders involved with a comprehensive digital representation containing all the necessary information to fully understand the structure’s current condition, keep track of any progressing deterioration, estimate the reduced load bearing capacity of the damaged element in the model or simulate the propagation of cracks to make well-informed decisions interactively and facilitate maintenance actions that optimally extend the service life of the structure. Though significant progress has been recently made in information modelling of damages, the current devised methods for the geometrical modelling approach are cumbersome and time consuming to implement in a full-scale model. For crack damages, an approach for a feasible automated image-based modelling is proposed utilising neural networks, classical computer vision and computational geometry techniques with the aim of creating valid shapes to be introduced into the information model, including related semantic properties and attributes from inspection data (e.g., width, depth, length, date, etc.). The creation of such models opens the door for further possible uses ranging from more accurate structural analysis possibilities to simulation of damage propagation in model elements, estimating deterioration rates and allows for better documentation, data sharing, and realistic visualisation of damages in a 3D model. KW - Building Information Modeling KW - BIM KW - IFC KW - Damage Information Modelling KW - Cracks Segmentation KW - Cracks 3D Modelling KW - Netscape Internet Foundation Classes Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230818-64162 ER - TY - GEN A1 - Lösel, Joy-Fabienne T1 - Fungal Future – Der Zukunft gewachsen N2 - Die Auswirkungen der durch den Kapitalismus befeuerten Umweltzerstörung werden immer deutlicher erkennbar. Unsere Gesellschaft ist nun damit konfrontiert, dass ihre kulturelle Identität, aber auch ihr Wohlstand sowohl eng mit Konsum und Wirtschaftswachstum als auch mit der Gesundheit der Natur verbunden sind. Es scheint ein geeigneter Moment, um die Perspektive zu wechseln und einer neuen Form des Wachstums eine Chance zu geben. Pilze sind eine von der Region unabhängige, natürlich vorkommende Ressource, die lokal angebaut und verarbeitet werden kann, ohne die Umwelt zu belasten. Pilze sind klimafreundlich, müllvermeidend und in bestehende natürliche Kreisläufe inkludierbar. Kurzum, Pilze sind cool, doch das wissen nicht Viele. Das sollte sich ändern. Mit Myzelwachstum gegen das Wachstumsparadigma. T3 - LUCIA Open Paper - 5 KW - Pilze KW - Nachhaltigkeit Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210603-44408 VL - 2021 PB - Lucia Verlag CY - Weimar ER - TY - THES A1 - Rost, Grit T1 - Entwicklung eines Toolboxmodells als Planungswerkzeug für ein transdisziplinäres Wasserressourcenmanagement am Beispiel der Stadt Darkhan, Mongolei N2 - Im Rahmen der Dissertation wurde ein Toolboxmodell für transdisziplinäres Wasserressourcenmanagement entwickelt. Das Modell liefert den methodischen Rahmen Wasserressourcen nachhaltig und transdisziplinär zu bewirtschaften. Der Begriff der Nachhaltigkeit und eine Konkretisierung der nachhaltigen Bewirtschaftung globaler Wasserressourcen scheinen unüberschaubar und suggerieren die Forderung nach einer neuen Weltformel. Die globale Bedeutung der Wasserressourcen, die für Regionen spezifischen Besonderheiten des natürlichen Wasserhaushalts und der anthropogenen Nutzung, die Zeitskala und die Kontextualisierung in alle betroffenen und benachbarten Disziplinen deuten auf die Komplexität der Thematik hin. Es wird eine Systematisierung des Planungsprozesses von Wasserressourcen notwendig, anhand derer eine holistische Herangehensweise mit einer Strategieentwicklung für Regionen spezifischer Schwerpunktprobleme erfolgt. Ziel der Arbeit ist die Erarbeitung einer Strategie zur Systematisierung nach diesen Forderungen und die Bereitstellung eines Toolboxmodelles als Planungswerkzeug für das transdisziplinäre Wasserressourcenmanagement. Das Toolboxmodell stellt den konzeptionellen Rahmen für die Bewirtschaftung von Wasserressourcen mit der Anwendung transdisziplinärer Forschungsmethoden bereit. Wesentliche Herausforderung bei der Anwendung der transdisziplinären Methode sind die Implementierung verschiedener Skalenbereiche, der Umgang mit der Komplexität von Daten, das Bewahren von Transparenz und Objektivität sowie die Ermöglichung eines auf andere Regionen übertragbaren Planungsprozesses. Die theoretischen Grundlagen naturwissenschaftlicher Forschung zur Nachhaltigkeit haben ihren Ursprung in den biologischen und geographischen Disziplinen. Das Ineinandergreifen naturräumlicher Zusammenhänge und der Einfluss anthropogener Nutzung und technischer Innovationen auf den Naturhaushalt sind Kern der Kausalität übergreifenden Denkens und Verstehens. Mit dem Ansatz des integrierten Wasserressourcenmanagements (IWRM) erfolgt die Berücksichtigung wirtschaftlicher und sozioökonomischer Ziele in den Planungsprozess für ökologisch nachhaltige Wasserwirtschaft. Das Instrument der Wasserrahmenrichtlinie (EU-WRRL) ist auf eine Gewässerökologie ausgerichtete Richtlinie, welche die Integration verschiedener Interessenvertreter in den Planungsprozess vorsieht. Das Konzept der neuartigen Sanitärsysteme basiert auf Stoffflüssen zwischen konkurrierenden Handlungsbereichen, wie Abfall-, Ressourcen- und Landwirtschaft. Den integrierten Ansätzen fehlt eine übergeordnete gemeinsame Zielstrategie – eine sogenannte Phase Null. Diese Phase Null – das Lernen aller 7 Zusammenfassung 157 relevanten, konkurrierenden und harmonisierenden Handlungsfelder eines Planungshorizontes wird durch eine transdisziplinäre Perspektive ermöglicht. Während bei der integralen Perspektive eine disziplinorientierte Kooperation im Vordergrund steht, verlangt die transdisziplinäre Perspektive nach einer problemorientierten Kooperation zwischen den Interessenvertretern (Werlen 2015). Die bestehenden Konzepte und Richtlinien für das nachhaltige Management von Wasserressourcen sind etabliert und evaluiert. Der Literatur zur Folge ist eine Weiterentwicklung nach der Perspektive der Transdisziplinarität erforderlich. Das Toolboxmodell für integrales Wasserressourcenmanagement entspricht einem Planungstool bestehend aus Werkzeugen für die Anwendung wissenschaftlicher Methoden. Die Zusammenstellung der Methoden/Werkzeuge erfüllt im Rahmen die Methode transdisziplinärer Forschung. Das Werkzeug zum Aufstellen der relevanten Handlungsfelder umfasst die Charakterisierung eines Untersuchungsgebietes und Planungsrahmens, die kausale Verknüpfung des Bewirtschaftungskonzeptes und konkurrierender sowie sich unterstützender Stakeholder. Mit dem Werkzeug der Kontextualisierung und Indikatorenaufstellung wird eine Methode der stufenweisen und von einer Skala unabhängigen Bewertung des Umweltzustandes für die Zielpriorisierung vorgenommen. Damit wird das Toolboxmodell dem Problem der Komplexität und Datenverfügbarkeit gerecht. Anhand der eingesetzten ABC Methode, werden die Bewertungsgrößen differenziert strukturiert auf verschiedene Skalen und Datenressourcen (A=Ersterkennung,B=Zeigerwerte, C=Modell/Index). Die ABC-Methode ermöglicht die Planung bereits mit unsicherer und lückenhafter Datengrundlage, ist jederzeit erweiterbar und bietet somit eine operative Wissensgenerierung während des Gestaltungsprozesses. Für das Werkzeug zur Bewertung und Priorisierung wird der Algorithmus der Composite Programmierung angewandt. Diese Methode der Mehrfachzielplanung erfüllt den Anspruch der permanenten Erweiterbarkeit und der transparenten und objektiven Entscheidungsfindung. Die Komplexität des transdisziplinären Wasserressourcenmanagements kann durch die Methode der Composite Programmierung systematisiert werden. Das wesentliche Ergebnis der Arbeit stellt die erfolgreiche Erarbeitung und Anwendung des Tool-boxmodells für das transdisziplinäre Wasserressourcenmanagement im Untersuchungsgebiet Stadt Darkhan in der Mongolei dar. Auf Grund seiner besonderen hydrologischen und strukturellen Situa-tion wird die Relevanz eines nachhaltigen Bewirtschaftungskonzeptes deutlich. Im Rahmen des Querschnittsmoduls des MoMo-Projektes wurde eine für das Toolboxmodell geeignete Datengrundlage erarbeitet. Planungsrelevante Handlungsfelder wurden im Rahmen eines Workshops mit verschiedenen Interessenvertretern erarbeitet. Im Ergebnis dessen wurde die Systematik eines Zielbaumes mit Hauptzielen und untergeordneten Teilzielen als Grundlage der Priorisierung nach den holistischen Anspruch der transdisziplinären Forschung aufgestellt. Für die Messbarkeit, in-wieweit Teilziele erreicht sind oder Handlungsbedarf besteht, wurden Indikatoren erarbeitet. Die Indikatoren-Aufstellung erfolgte exemplarisch für das Handlungsfeld Siedlungswasserwirtschaft in allen Skalen des ABC-Systems. Die im BMBF-MoMo Projekt generierte umfassende Datengrundlage ermöglichte die Anwendung und Evaluierung des Toolboxmodells mit unterschiedlichem quantitativem und qualitativem Dateninput. Verschiedene Kombination von A (Ersterkennung), B (Zeigerwerte) und C (Modell/Index) als Grundlage der Priorisierung mit der Compostite Programmierung ermöglichten die Durchführung und Bewertung des transdisziplinären Planungstools. Die er-mittelten Rangfolgen von Teilzielen mit unterschiedlichen Bewertungsvarianten ergaben ähnliche Tendenzen. Das ist ein Hinweis dafür, dass für die zukünftige Anwendung des Toolboxmodells die operative Wissensgenerierung, d.h. das schrittweise Hinzufügen neu ermittelter, gesicherterer Daten, funktioniert. Eine schwierige Datenverfügbarkeit oder eine noch im Prozess befindliche wissenschaftliche Analyse sollen keine Hindernisse für eine schrittweise und erweiterbare Zielpriorisierung und Maßnahmenplanung sein. Trotz der Komplexität des transdisziplinären Ansatzes wird durch die Anwendung des Toolboxmodells eine effiziente und zielorientierte Handlungspriorisierung ermöglicht. Die Effizienz wird erreicht durch ressourcenschonende und flexible, Ziel fokussierte Datenermittlung. Zeit und Kosten im Planungsprozess können eingespart werden. Die erzielte Priorisierung von letztlich Handlungsempfehlungen erfolgt individuell auf die Eigenart des Untersuchungsgebietes angepasst, was hinsichtlich seiner Wirkung als erfolgsversprechend gilt. T3 - Schriften der Bauhaus-Universität Weimar - 39 KW - Wasserreserve KW - Transdisziplinarität KW - Flussgebiet KW - Mongolei KW - Wasserressourcenmanagement KW - Mangement Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20201113-42874 SN - 978-3-941216-94-5 PB - Rhombus CY - Berlin ER - TY - THES A1 - Salavati, Mohammad T1 - Multi-Scale Modeling of Mechanical and Electrochemical Properties of 1D and 2D Nanomaterials, Application in Battery Energy Storage Systems N2 - Material properties play a critical role in durable products manufacturing. Estimation of the precise characteristics in different scales requires complex and expensive experimental measurements. Potentially, computational methods can provide a platform to determine the fundamental properties before the final experiment. Multi-scale computational modeling leads to the modeling of the various time, and length scales include nano, micro, meso, and macro scales. These scales can be modeled separately or in correlation with coarser scales. Depend on the interested scales modeling, the right selection of multi-scale methods leads to reliable results and affordable computational cost. The present dissertation deals with the problems in various length and time scales using computational methods include density functional theory (DFT), molecular mechanics (MM), molecular dynamics (MD), and finite element (FE) methods. Physical and chemical interactions in lower scales determine the coarser scale properties. Particles interaction modeling and exploring fundamental properties are significant challenges of computational science. Downscale modelings need more computational effort due to a large number of interacted atoms/particles. To deal with this problem and bring up a fine-scale (nano) as a coarse-scale (macro) problem, we extended an atomic-continuum framework. The discrete atomic models solve as a continuum problem using the computationally efficient FE method. MM or force field method based on a set of assumptions approximates a solution on the atomic scale. In this method, atoms and bonds model as a harmonic oscillator with a system of mass and springs. The negative gradient of the potential energy equal to the forces on each atom. In this way, each bond's total potential energy includes bonded, and non-bonded energies are simulated as equivalent structural strain energies. Finally, the chemical nature of the atomic bond is modeled as a piezoelectric beam element that solves by the FE method. Exploring novel materials with unique properties is a demand for various industrial applications. During the last decade, many two-dimensional (2D) materials have been synthesized and shown outstanding properties. Investigation of the probable defects during the formation/fabrication process and studying their strength under severe service life are the critical tasks to explore performance prospects. We studied various defects include nano crack, notch, and point vacancy (Stone-Wales defect) defects employing MD analysis. Classical MD has been used to simulate a considerable amount of molecules at micro-, and meso- scales. Pristine and defective nanosheet structures considered under the uniaxial tensile loading at various temperatures using open-source LAMMPS codes. The results were visualized with the open-source software of OVITO and VMD. Quantum based first principle calculations have been conducting at electronic scales and known as the most accurate Ab initio methods. However, they are computationally expensive to apply for large systems. We used density functional theory (DFT) to estimate the mechanical and electrochemical response of the 2D materials. Many-body Schrödinger's equation describes the motion and interactions of the solid-state particles. Solid describes as a system of positive nuclei and negative electrons, all electromagnetically interacting with each other, where the wave function theory describes the quantum state of the set of particles. However, dealing with the 3N coordinates of the electrons, nuclei, and N coordinates of the electrons spin components makes the governing equation unsolvable for just a few interacted atoms. Some assumptions and theories like Born Oppenheimer and Hartree-Fock mean-field and Hohenberg-Kohn theories are needed to treat with this equation. First, Born Oppenheimer approximation reduces it to the only electronic coordinates. Then Kohn and Sham, based on Hartree-Fock and Hohenberg-Kohn theories, assumed an equivalent fictitious non-interacting electrons system as an electron density functional such that their ground state energies are equal to a set of interacting electrons. Exchange-correlation energy functionals are responsible for satisfying the equivalency between both systems. The exact form of the exchange-correlation functional is not known. However, there are widely used methods to derive functionals like local density approximation (LDA), Generalized gradient approximation (GGA), and hybrid functionals (e.g., B3LYP). In our study, DFT performed using VASP codes within the GGA/PBE approximation, and visualization/post-processing of the results realized via open-source software of VESTA. The extensive DFT calculations are conducted 2D nanomaterials prospects as anode/cathode electrode materials for batteries. Metal-ion batteries' performance strongly depends on the design of novel electrode material. Two-dimensional (2D) materials have developed a remarkable interest in using as an electrode in battery cells due to their excellent properties. Desirable battery energy storage systems (BESS) must satisfy the high energy density, safe operation, and efficient production costs. Batteries have been using in electronic devices and provide a solution to the environmental issues and store the discontinuous energies generated from renewable wind or solar power plants. Therefore, exploring optimal electrode materials can improve storage capacity and charging/discharging rates, leading to the design of advanced batteries. Our results in multiple scales highlight not only the proposed and employed methods' efficiencies but also promising prospect of recently synthesized nanomaterials and their applications as an anode material. In this way, first, a novel approach developed for the modeling of the 1D nanotube as a continuum piezoelectric beam element. The results converged and matched closely with those from experiments and other more complex models. Then mechanical properties of nanosheets estimated and the failure mechanisms results provide a useful guide for further use in prospect applications. Our results indicated a comprehensive and useful vision concerning the mechanical properties of nanosheets with/without defects. Finally, mechanical and electrochemical properties of the several 2D nanomaterials are explored for the first time—their application performance as an anode material illustrates high potentials in manufacturing super-stretchable and ultrahigh-capacity battery energy storage systems (BESS). Our results exhibited better performance in comparison to the available commercial anode materials. KW - Batterie KW - Modellierung KW - Nanostrukturiertes Material KW - Mechanical properties KW - Multi-scale modeling KW - Energiespeichersystem KW - Elektrodenmaterial KW - Elektrode KW - Mechanische Eigenschaft KW - Elektrochemische Eigenschaft KW - Electrochemical properties KW - Battery development KW - Nanomaterial Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200623-41830 ER - TY - THES A1 - Cicek, Burhan A1 - Cancino, Pamela T1 - Küreken 2013. Entwerfen eines Dorfes aus Lehm N2 - Die Diskussionen in der Politik und in der Gesellschaft über Klimawandel, globale Erwärmung oder Nachhaltigkeit, die schon noch länger anhält, werden nie ein Ende finden, solange die Probleme, auf denen sie basiert, unlösbar bleiben. Vorgeschlagene Lösungen werden meist nicht richtig umgesetzt. Im Zusammenhang mit dieser Problematik steigt aber das Verantwortungsgefühl für bessere Zukunftsstrategien immer mehr. Die in den letzten Jahren vorgekommenen Umweltkatastrophen, wie im Golf von Mexiko (April 2010) oder im Fukushima (März 2011) die noch aktuell sind, zeigen, dass der Primärenergieeinsatz oder die Transportproblematik nicht mehr nur die Sorge der Entwicklungsländer, sondern auch der Industrieländer ist. Die Bauwelt mit ihrem erheblichen Energiebedarf spielt bei der Festlegung der Zukunftsstrategien eine große Rolle. Vor allem sind die Forschungen nach umweltfreundlichen Materialien, der Recyclebarkeit der eingesetzten Baumaterialien oder dem vernünftigen Nutzen der Naturressourcen die wichtigsten Schwerpunkte. In dieser Hinsicht bringt Lehm als Baumaterial viele Vorteile mit sich. Bei einem Artikel sagt der Lehmbauexperte Martin Rauch: “In heutiger Zeit und einem Kulturkreis, in dem Baugrund und Arbeitszeit unsere großen Kosten verursachen, findet der tradierte Lehmbau mit dem verbundenen großen Aufwand an menschlicher Arbeitszeit nur schwer seinen Platz. Über die Art der Bauweise wird auch die Entscheidung gefällt, wie und wo die Wertschöpfung erfolgt und ob der Einsatz des Budgets einen gesellschaftlichen Nutzen mit sich bringt. Im Vergleich zu einem Sichtbetonhaus können bei einem Stampflehmhaus 40% der Primärenergie ein gespart und dafür mehr lokale Arbeitsressourcen gebunden werden. Davon profitieren vor allem die lokalen Handwerker und mittelständischen Betriebe” Anatolien ist der Ort, wo man immer noch die tiefsten Wurzeln der Baukultur menschlicher Geschichte findet. Diese Baukultur, die in den vergangenen Jahrzehnten fast verlorengegangen ist, ist die Lehmbaukultur. In dieser Hinsicht beabsichtigt dieser Entwurf die Würde des Lehms in Anatolien wieder herzustellen und dadurch dessen Glaubwürdigkeit zurückzubringen. KW - Lehm KW - Lehmbau KW - stabilisierter Lehm KW - Stampflehm KW - Alker Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20240507-63568 ER - TY - THES A1 - Piethe, Vivienne T1 - Konfektionierung eines Calciumsulfat-Bindemittelsystems zur Herstellung volumenstabiler Fließestrichmörtel N2 - Bei einem marktüblichen Calciumsulfat-Fließestrich wurden in der Praxis schädigende Volu-menexpansionen festgestellt. Diese sind ein Resultat aus dem Zusammenwirken des einge-setzten Bindemittel-Compounds und einer kritischen Gesteinskörnung. Das Ziel dieser Arbeit ist es, ein Calciumsulfat-Bindemittelsystem zu konfektionieren, welches in der Lage ist, die im Mörtel festgestellten Volumenexpansionen zu unterbinden. Es sollen verschiedene Bindemittel- und Additivzusammensetzungen untersucht werden, welche in Verbindung mit der kritischen Gesteinskörnung die Herstellung eines volumenstabilen Fließestrichs ermöglichen. Dazu soll folgende Fragestellung beantwortet werden: Welche Ursachen hat die Volumenzunahme und wie ist diese zu minimieren bzw. unterbinden? Dabei werden unterschiedliche Bindemittelrezepturen aus α-Halbhydrat, Thermoanhydrit und Naturanhydrit, sowie verschiedene Additivzusammensetzungen hergestellt und untersucht. Durch Längenänderungsmessungen in der Schwindrinne werden die Einflüsse der Binde-mittel, der Additivzusammensetzungen und der Wasser/Bindemittel-Werte auf das Län-genänderungsverhalten untersucht. Mittels Variation der einzelnen Compound-Bestandteile kann festgestellt werden, dass der Stabilisierer die Längenänderung negativ beeinflusst. Dieser bindet freies Wasser, welches für eine Reaktion zwischen Bindemittel und Gesteins-körnung im plastischen Zustand nicht mehr zur Verfügung steht. Diese Reaktion kann folglich erst im erhärteten Zustand ablaufen und verursacht die schädigende Volumenexpansion. Abschließend wurde ein Bindemittel-Compound konfektioniert, welcher ohne Zusatz von Stabilisierern in Zusammenhang mit der kritischen Gesteinskörnung volumenstabil ist und keine Schäden auslöst. KW - Calciumsulfat KW - Gips KW - Fließestrich KW - Volumenstabilität KW - Calciumsulfatfließestrich Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20190902-39445 ER - TY - INPR A1 - Radmard Rahmani, Hamid A1 - Könke, Carsten T1 - Passive Control of Tall Buildings Using Distributed Multiple Tuned Mass Dampers N2 - The vibration control of the tall building during earthquake excitations is a challenging task due to their complex seismic behavior. This paper investigates the optimum placement and properties of the Tuned Mass Dampers (TMDs) in tall buildings, which are employed to control the vibrations during earthquakes. An algorithm was developed to spend a limited mass either in a single TMD or in multiple TMDs and distribute them optimally over the height of the building. The Non-dominated Sorting Genetic Algorithm (NSGA – II) method was improved by adding multi-variant genetic operators and utilized to simultaneously study the optimum design parameters of the TMDs and the optimum placement. The results showed that under earthquake excitations with noticeable amplitude in higher modes, distributing TMDs over the height of the building is more effective in mitigating the vibrations compared to the use of a single TMD system. From the optimization, it was observed that the locations of the TMDs were related to the stories corresponding to the maximum modal displacements in the lower modes and the stories corresponding to the maximum modal displacements in the modes which were highly activated by the earthquake excitations. It was also noted that the frequency content of the earthquake has significant influence on the optimum location of the TMDs. KW - Schwingungsdämpfer KW - Hochbau KW - tall buildings KW - passive control KW - genetic algorithm KW - tuned mass dampers Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20190311-38597 UR - https://www.researchgate.net/publication/330508976_Seismic_Control_of_Tall_Buildings_Using_Distributed_Multiple_Tuned_Mass_Dampers ER - TY - THES A1 - Zhang, Yongzheng T1 - A Nonlocal Operator Method for Quasi-static and Dynamic Fracture Modeling N2 - Material failure can be tackled by so-called nonlocal models, which introduce an intrinsic length scale into the formulation and, in the case of material failure, restore the well-posedness of the underlying boundary value problem or initial boundary value problem. Among nonlocal models, peridynamics (PD) has attracted a lot of attention as it allows the natural transition from continuum to discontinue and thus allows modeling of discrete cracks without the need to describe and track the crack topology, which has been a major obstacle in traditional discrete crack approaches. This is achieved by replacing the divergence of the Cauchy stress tensor through an integral over so-called bond forces, which account for the interaction of particles. A quasi-continuum approach is then used to calibrate the material parameters of the bond forces, i.e., equating the PD energy with the energy of a continuum. One major issue for the application of PD to general complex problems is that they are limited to fairly simple material behavior and pure mechanical problems based on explicit time integration. PD has been extended to other applications but losing simultaneously its simplicity and ease in modeling material failure. Furthermore, conventional PD suffers from instability and hourglass modes that require stabilization. It also requires the use of constant horizon sizes, which drastically reduces its computational efficiency. The latter issue was resolved by the so-called dual-horizon peridynamics (DH-PD) formulation and the introduction of the duality of horizons. Within the nonlocal operator method (NOM), the concept of nonlocality is further extended and can be considered a generalization of DH-PD. Combined with the energy functionals of various physical models, the nonlocal forms based on the dual-support concept can be derived. In addition, the variation of the energy functional allows implicit formulations of the nonlocal theory. While traditional integral equations are formulated in an integral domain, the dual-support approaches are based on dual integral domains. One prominent feature of NOM is its compatibility with variational and weighted residual methods. The NOM yields a direct numerical implementation based on the weighted residual method for many physical problems without the need for shape functions. Only the definition of the energy or boundary value problem is needed to drastically facilitate the implementation. The nonlocal operator plays an equivalent role to the derivatives of the shape functions in meshless methods and finite element methods (FEM). Based on the variational principle, the residual and the tangent stiffness matrix can be obtained with ease by a series of matrix multiplications. In addition, NOM can be used to derive many nonlocal models in strong form. The principal contributions of this dissertation are the implementation and application of NOM, and also the development of approaches for dealing with fractures within the NOM, mostly for dynamic fractures. The primary coverage and results of the dissertation are as follows: -The first/higher-order implicit NOM and explicit NOM, including a detailed description of the implementation, are presented. The NOM is based on so-called support, dual-support, nonlocal operators, and an operate energy functional ensuring stability. The nonlocal operator is a generalization of the conventional differential operators. Combining with the method of weighted residuals and variational principles, NOM establishes the residual and tangent stiffness matrix of operate energy functional through some simple matrix without the need of shape functions as in other classical computational methods such as FEM. NOM only requires the definition of the energy drastically simplifying its implementation. For the sake of conciseness, the implementation in this chapter is focused on linear elastic solids only, though the NOM can handle more complex nonlinear problems. An explicit nonlocal operator method for the dynamic analysis of elasticity solid problems is also presented. The explicit NOM avoids the calculation of the tangent stiffness matrix as in the implicit NOM model. The explicit scheme comprises the Verlet-velocity algorithm. The NOM can be very flexible and efficient for solving partial differential equations (PDEs). It's also quite easy for readers to use the NOM and extend it to solve other complicated physical phenomena described by one or a set of PDEs. Several numerical examples are presented to show the capabilities of this method. -A nonlocal operator method for the dynamic analysis of (thin) Kirchhoff plates is proposed. The nonlocal Hessian operator is derived from a second-order Taylor series expansion. NOM is higher-order continuous, which is exploited for thin plate analysis that requires $C^1$ continuity. The nonlocal dynamic governing formulation and operator energy functional for Kirchhoff plates are derived from a variational principle. The Verlet-velocity algorithm is used for time discretization. After confirming the accuracy of the nonlocal Hessian operator, several numerical examples are simulated by the nonlocal dynamic Kirchhoff plate formulation. -A nonlocal fracture modeling is developed and applied to the simulation of quasi-static and dynamic fractures using the NOM. The phase field's nonlocal weak and associated strong forms are derived from a variational principle. The NOM requires only the definition of energy. We present both a nonlocal implicit phase field model and a nonlocal explicit phase field model for fracture; the first approach is better suited for quasi-static fracture problems, while the key application of the latter one is dynamic fracture. To demonstrate the performance of the underlying approach, several benchmark examples for quasi-static and dynamic fracture are solved. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,9 KW - Variationsprinzip KW - Partial Differential Equations KW - Taylor Series Expansion KW - Peridynamics KW - Variational principle KW - Phase field method KW - Peridynamik KW - Phasenfeldmodell KW - Partielle Differentialgleichung KW - Nichtlokale Operatormethode Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20221026-47321 ER - TY - THES A1 - López Zermeño, Jorge Alberto T1 - Isogeometric and CAD-based methods for shape and topology optimization: Sensitivity analysis, Bézier elements and phase-field approaches N2 - The Finite Element Method (FEM) is widely used in engineering for solving Partial Differential Equations (PDEs) over complex geometries. To this end, it is required to provide the FEM software with a geometric model that is typically constructed in a Computer-Aided Design (CAD) software. However, FEM and CAD use different approaches for the mathematical description of the geometry. Thus, it is required to generate a mesh, which is suitable for FEM, based on the CAD model. Nonetheless, this procedure is not a trivial task and it can be time consuming. This issue becomes more significant for solving shape and topology optimization problems, which consist in evolving the geometry iteratively. Therefore, the computational cost associated to the mesh generation process is increased exponentially for this type of applications. The main goal of this work is to investigate the integration of CAD and CAE in shape and topology optimization. To this end, numerical tools that close the gap between design and analysis are presented. The specific objectives of this work are listed below: • Automatize the sensitivity analysis in an isogeometric framework for applications in shape optimization. Applications for linear elasticity are considered. • A methodology is developed for providing a direct link between the CAD model and the analysis mesh. In consequence, the sensitivity analysis can be performed in terms of the design variables located in the design model. • The last objective is to develop an isogeometric method for shape and topological optimization. This method should take advantage of using Non-Uniform Rational B-Splines (NURBS) with higher continuity as basis functions. Isogeometric Analysis (IGA) is a framework designed to integrate the design and analysis in engineering problems. The fundamental idea of IGA is to use the same basis functions for modeling the geometry, usually NURBS, for the approximation of the solution fields. The advantage of integrating design and analysis is two-fold. First, the analysis stage is more accurate since the system of PDEs is not solved using an approximated geometry, but the exact CAD model. Moreover, providing a direct link between the design and analysis discretizations makes possible the implementation of efficient sensitivity analysis methods. Second, the computational time is significantly reduced because the mesh generation process can be avoided. Sensitivity analysis is essential for solving optimization problems when gradient-based optimization algorithms are employed. Automatic differentiation can compute exact gradients, automatically by tracking the algebraic operations performed on the design variables. For the automation of the sensitivity analysis, an isogeometric framework is used. Here, the analysis mesh is obtained after carrying out successive refinements, while retaining the coarse geometry for the domain design. An automatic differentiation (AD) toolbox is used to perform the sensitivity analysis. The AD toolbox takes the code for computing the objective and constraint functions as input. Then, using a source code transformation approach, it outputs a code for computing the objective and constraint functions, and their sensitivities as well. The sensitivities obtained from the sensitivity propagation method are compared with analytical sensitivities, which are computed using a full isogeometric approach. The computational efficiency of AD is comparable to that of analytical sensitivities. However, the memory requirements are larger for AD. Therefore, AD is preferable if the memory requirements are satisfied. Automatic sensitivity analysis demonstrates its practicality since it simplifies the work of engineers and designers. Complex geometries with sharp edges and/or holes cannot easily be described with NURBS. One solution is the use of unstructured meshes. Simplex-elements (triangles and tetrahedra for two and three dimensions respectively) are particularly useful since they can automatically parameterize a wide variety of domains. In this regard, unstructured Bézier elements, commonly used in CAD, can be employed for the exact modelling of CAD boundary representations. In two dimensions, the domain enclosed by NURBS curves is parameterized with Bézier triangles. To describe exactly the boundary of a two-dimensional CAD model, the continuity of a NURBS boundary representation is reduced to C^0. Then, the control points are used to generate a triangulation such that the boundary of the domain is identical to the initial CAD boundary representation. Thus, a direct link between the design and analysis discretizations is provided and the sensitivities can be propagated to the design domain. In three dimensions, the initial CAD boundary representation is given as a collection of NURBS surfaces that enclose a volume. Using a mesh generator (Gmsh), a tetrahedral mesh is obtained. The original surface is reconstructed by modifying the location of the control points of the tetrahedral mesh using Bézier tetrahedral elements and a point inversion algorithm. This method offers the possibility of computing the sensitivity analysis using the analysis mesh. Then, the sensitivities can be propagated into the design discretization. To reuse the mesh originally generated, a moving Bézier tetrahedral mesh approach was implemented. A gradient-based optimization algorithm is employed together with a sensitivity propagation procedure for the shape optimization cases. The proposed shape optimization approaches are used to solve some standard benchmark problems in structural mechanics. The results obtained show that the proposed approach can compute accurate gradients and evolve the geometry towards optimal solutions. In three dimensions, the moving mesh approach results in faster convergence in terms of computational time and avoids remeshing at each optimization step. For considering topological changes in a CAD-based framework, an isogeometric phase-field based shape and topology optimization is developed. In this case, the diffuse interface of a phase-field variable over a design domain implicitly describes the boundaries of the geometry. The design variables are the local values of the phase-field variable. The descent direction to minimize the objective function is found by using the sensitivities of the objective function with respect to the design variables. The evolution of the phase-field is determined by solving the time dependent Allen-Cahn equation. Especially for topology optimization problems that require C^1 continuity, such as for flexoelectric structures, the isogeometric phase field method is of great advantage. NURBS can achieve the desired continuity more efficiently than the traditional employed functions. The robustness of the method is demonstrated when applied to different geometries, boundary conditions, and material configurations. The applications illustrate that compared to piezoelectricity, the electrical performance of flexoelectric microbeams is larger under bending. In contrast, the electrical power for a structure under compression becomes larger with piezoelectricity. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,4 KW - CAD KW - Gestaltoptimierung KW - Topologieoptimierung KW - Isogeometrische Analyse KW - Finite-Elemente-Methode KW - Computer-Aided Design KW - Shape Optimization KW - Topology Optimization KW - Isogeometric Analysis KW - Finite Element Method Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220831-47102 ER - TY - THES A1 - Zacharias, Christin T1 - Numerical Simulation Models for Thermoelastic Damping Effects N2 - Finite Element Simulations of dynamically excited structures are mainly influenced by the mass, stiffness, and damping properties of the system, as well as external loads. The prediction quality of dynamic simulations of vibration-sensitive components depends significantly on the use of appropriate damping models. Damping phenomena have a decisive influence on the vibration amplitude and the frequencies of the vibrating structure. However, developing realistic damping models is challenging due to the multiple sources that cause energy dissipation, such as material damping, different types of friction, or various interactions with the environment. This thesis focuses on thermoelastic damping, which is the main cause of material damping in homogeneous materials. The effect is caused by temperature changes due to mechanical strains. In vibrating structures, temperature gradients arise in adjacent tension and compression areas. Depending on the vibration frequency, they result in heat flows, leading to increased entropy and the irreversible transformation of mechanical energy into thermal energy. The central objective of this thesis is the development of efficient simulation methods to incorporate thermoelastic damping in finite element analyses based on modal superposition. The thermoelastic loss factor is derived from the structure's mechanical mode shapes and eigenfrequencies. In subsequent analyses that are performed in the time and frequency domain, it is applied as modal damping. Two approaches are developed to determine the thermoelastic loss in thin-walled plate structures, as well as three-dimensional solid structures. The realistic representation of the dissipation effects is verified by comparing the simulation results with experimentally determined data. Therefore, an experimental setup is developed to measure material damping, excluding other sources of energy dissipation. The three-dimensional solid approach is based on the determination of the generated entropy and therefore the generated heat per vibration cycle, which is a measure for thermoelastic loss in relation to the total strain energy. For thin plate structures, the amount of bending energy in a modal deformation is calculated and summarized in the so-called Modal Bending Factor (MBF). The highest amount of thermoelastic loss occurs in the state of pure bending. Therefore, the MBF enables a quantitative classification of the mode shapes concerning the thermoelastic damping potential. The results of the developed simulations are in good agreement with the experimental results and are appropriate to predict thermoelastic loss factors. Both approaches are based on modal superposition with the advantage of a high computational efficiency. Overall, the modeling of thermoelastic damping represents an important component in a comprehensive damping model, which is necessary to perform realistic simulations of vibration processes. N2 - Die Finite-Elemente Simulation von dynamisch angeregten Strukturen wird im Wesentlich durch die Steifigkeits-, Massen- und Dämpfungseigenschaften des Systems sowie durch die äußere Belastung bestimmt. Die Vorhersagequalität von dynamischen Simulationen schwingungsanfälliger Bauteile hängt wesentlich von der Verwendung geeigneter Dämpfungsmodelle ab. Dämpfungsphänomene haben einen wesentlichen Einfluss auf die Schwingungsamplitude, die Frequenz und teilweise sogar die Existenz von Vibrationen. Allerdings ist die Entwicklung von realitätsnahen Dämpfungsmodellen oft schwierig, da eine Vielzahl von physikalischen Effekten zur Energiedissipation während eines Schwingungsvorgangs führt. Beispiele hierfür sind die Materialdämpfung, verschiedene Formen der Reibung sowie vielfältige Wechselwirkungen mit dem umgebenden Medium. Diese Dissertation befasst sich mit thermoelastischer Dämpfung, die in homogenen Materialien die dominante Ursache der Materialdämpfung darstellt. Der thermoelastische Effekt wird ausgelöst durch eine Temperaturänderung aufgrund mechanischer Spannungen. In der schwingenden Struktur entstehen während der Deformation Temperaturgradienten zwischen benachbarten Regionen unter Zug- und Druckbelastung. In Abhängigkeit von der Vibrationsfrequenz führen diese zu Wärmeströmen und irreversibler Umwandlung mechanischer in thermische Energie. Die Zielstellung dieser Arbeit besteht in der Entwicklung recheneffizienter Simulationsmethoden, um thermoelastische Dämpfung in zeitabhängigen Finite-Elemente Analysen, die auf modaler Superposition beruhen, zu integrieren. Der thermoelastische Verlustfaktor wird auf der Grundlage der mechanischen Eigenformen und -frequenzen bestimmt. In nachfolgenden Analysen im Zeit- und Frequenzbereich wird er als modaler Dämpfungsgrad verwendet. Zwei Ansätze werden entwickelt, um den thermoelastischen Verlustfaktor in dünn-wandigen Plattenstrukturen, sowie in dreidimensionalen Volumenbauteilen zu simulieren. Die realitätsnahe Vorhersage der Energiedissipation wird durch die Verifizierung an experimentellen Daten bestätigt. Dafür wird ein Versuchsaufbau entwickelt, der eine Messung von Materialdämpfung unter Ausschluss anderer Dissipationsquellen ermöglicht. Für den Fall der Volumenbauteile wird ein Ansatz verwendet, der auf der Berechnung der Entropieänderung und damit der erzeugte Wärmeenergie während eines Schwingungszyklus beruht. Im Verhältnis zur Formänderungsenergie ist dies ein Maß für die thermoelastische Dämpfung. Für dünne Plattenstrukturen wird der Anteil an Biegeenergie in der Eigenform bestimmt und im sogenannten modalen Biegefaktor (MBF) zusammengefasst. Der maximale Grad an thermoelastischer Dämpfung kann im Zustand reiner Biegung auftreten, sodass der MBF eine quantitative Klassifikation der Eigenformen hinsichtlich ihres thermoelastischen Dämpfungspotentials zulässt. Die Ergebnisse der entwickelten Simulationsmethoden stimmen sehr gut mit den experimentellen Daten überein und sind geeignet, um thermoelastische Dämpfungsgrade vorherzusagen. Beide Ansätze basieren auf modaler Superposition und ermöglichen damit zeitabhängige Simulationen mit einer hohen Recheneffizienz. Insgesamt stellt die Modellierung der thermoelastischen Dämpfung einen Baustein in einem umfassenden Dämpfungsmodell dar, welches zur realitätsnahen Simulation von Schwingungsvorgängen notwendig ist. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,8 KW - Werkstoffdämpfung KW - Finite-Elemente-Methode KW - Strukturdynamik KW - Thermoelastic damping KW - modal damping KW - decay experiments KW - energy dissipation Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20221116-47352 ER - TY - THES A1 - Habtemariam, Abinet Kifle T1 - Generalized Beam Theory for the analysis of thin-walled circular pipe members N2 - The detailed structural analysis of thin-walled circular pipe members often requires the use of a shell or solid-based finite element method. Although these methods provide a very good approximation of the deformations, they require a higher degree of discretization which causes high computational costs. On the other hand, the analysis of thin-walled circular pipe members based on classical beam theories is easy to implement and needs much less computation time, however, they are limited in their ability to approximate the deformations as they cannot consider the deformation of the cross-section. This dissertation focuses on the study of the Generalized Beam Theory (GBT) which is both accurate and efficient in analyzing thin-walled members. This theory is based on the separation of variables in which the displacement field is expressed as a combination of predetermined deformation modes related to the cross-section, and unknown amplitude functions defined on the beam's longitudinal axis. Although the GBT was initially developed for long straight members, through the consideration of complementary deformation modes, which amend the null transverse and shear membrane strain assumptions of the classical GBT, problems involving short members, pipe bends, and geometrical nonlinearity can also be analyzed using GBT. In this dissertation, the GBT formulation for the analysis of these problems is developed and the application and capabilities of the method are illustrated using several numerical examples. Furthermore, the displacement and stress field results of these examples are verified using an equivalent refined shell-based finite element model. The developed static and dynamic GBT formulations for curved thin-walled circular pipes are based on the linear kinematic description of the curved shell theory. In these formulations, the complex problem in pipe bends due to the strong coupling effect of the longitudinal bending, warping and the cross-sectional ovalization is handled precisely through the derivation of the coupling tensors between the considered GBT deformation modes. Similarly, the geometrically nonlinear GBT analysis is formulated for thin-walled circular pipes based on the nonlinear membrane kinematic equations. Here, the initial linear and quadratic stress and displacement tangent stiffness matrices are built using the third and fourth-order GBT deformation mode coupling tensors. Longitudinally, the formulation of the coupled GBT element stiffness and mass matrices are presented using a beam-based finite element formulation. Furthermore, the formulated GBT elements are tested for shear and membrane locking problems and the limitations of the formulations regarding the membrane locking problem are discussed. N2 - Eine detaillierte Strukturanalyse dünnwandiger, kreisförmiger Rohrelemente erfordert oft die Verwendung von Schalenelementen in der Finite Elemente Methode. Diese Methode ermöglicht eine sehr gute Approximation des Verformungszustandes, erfordert jedoch einen hohen Grad der Diskretisierung, welcher wiederum einen hohen Rechenaufwand verursacht. Eine alternative Methode hierzu basiert auf klassischen Balkentheorien, welche eine einfache Modellierung ermöglichen und wesentlich geringeren Rechenaufwand erfordern. Diese weisen jedoch Einschränkungen bei der Approximation von Verformungen auf, da Querschnittsverformungen nicht berücksichtigt werden können. Schwerpunkt dieser Dissertation ist eine Untersuchung der Verallgemeinerten Technischen Biegetheorie (VTB), die sowohl eine genaue als auch eine effiziente Analyse von dünnwandigen Tragwerkselementen ermöglicht. Diese Theorie basiert auf einer Trennung der Variablen, in der das Verschiebungsfeld als eine Kombination von vorbestimmten Verformungsmoden der Querschnitts und unbekannten Amplitudenfunktionen in Längsrichtung ausgedrückt wird. Obwohl die VTB ursprünglich für lange, gerade Elemente entwickelt wurde, können durch die Berücksichtigung komplementärer Verformungsmoden, welche die Null-Annahmen der klassischen VTB für Quer- und Schubmembrandehnung abändern, Probleme mit kurzen Elementen, Rohrbögen und geometrischer Nichtlinearität analysiert werden. In dieser Dissertation wird die VTB-Formulierung für die Analyse dieser Probleme entwickelt. Die Anwendung und Möglichkeiten der Methode werden anhand mehrerer numerischer Beispiele veranschaulicht, deren Verschiebungs- und Spannungsfeldanalysen anhand eines äquivalenten, verfeinerten, schalenbasierten Finite-Elemente-Modells verifiziert werden. Die entwickelten statischen und dynamischen VTB-Formulierungen für Rohrbogenelemente basieren auf der linearen kinematischen Beschreibung der Theorie gekrümmter Schalen. In diesen Formulierungen wird das komplexe Problem in Rohrbögen aufgrund des starken Kopplungseffekts der Längsbiegung, der Verwölbung und der Querschnittsovalisierung durch die Herleitung der Kopplungstensoren zwischen den betrachteten VTB-Verformungsmoden präzise behandelt. In ähnlicher Weise wird die geometrisch nichtlineare VTB-Analyse für gerade Rohrelemente auf der Grundlage der nichtlinearen kinematischen Membrangleichungen formuliert. Die anfänglichen linearen und quadratischen Spannungs- und Verschiebungs-Tangentensteifigkeitsmatrizen werden dabei unter Verwendung der VTB-Kopplungstensoren dritter und vierter Ordnung aufgebaut. In Längsrichtung wird die Formulierung der gekoppelten VTB-Element-Steifigkeits- und Massenmatrizen unter Verwendung einer balkenbasierten Finite-Elemente Formulierung dargestellt. Weiterhin werden die VTB-Elemente auf Schub- und Membran-Locking-Probleme getestet und die Einschränkungen der Formulierungen bezüglich des Membran-Locking-Problems diskutiert. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,2 KW - Finite-Elemente-Methode KW - Dynamische Analyse KW - Generalized Beam Theory (GBT) KW - Finite Element Method KW - Dynamic Analysis KW - Geometrically nonlinear analysis KW - Curved thin-walled circular pipes Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220127-45723 ER - TY - THES A1 - Valizadeh, Navid T1 - Developments in Isogeometric Analysis and Application to High-Order Phase-Field Models of Biomembranes N2 - Isogeometric analysis (IGA) is a numerical method for solving partial differential equations (PDEs), which was introduced with the aim of integrating finite element analysis with computer-aided design systems. The main idea of the method is to use the same spline basis functions which describe the geometry in CAD systems for the approximation of solution fields in the finite element method (FEM). Originally, NURBS which is a standard technology employed in CAD systems was adopted as basis functions in IGA but there were several variants of IGA using other technologies such as T-splines, PHT splines, and subdivision surfaces as basis functions. In general, IGA offers two key advantages over classical FEM: (i) by describing the CAD geometry exactly using smooth, high-order spline functions, the mesh generation process is simplified and the interoperability between CAD and FEM is improved, (ii) IGA can be viewed as a high-order finite element method which offers basis functions with high inter-element continuity and therefore can provide a primal variational formulation of high-order PDEs in a straightforward fashion. The main goal of this thesis is to further advance isogeometric analysis by exploiting these major advantages, namely precise geometric modeling and the use of smooth high-order splines as basis functions, and develop robust computational methods for problems with complex geometry and/or complex multi-physics. As the first contribution of this thesis, we leverage the precise geometric modeling of isogeometric analysis and propose a new method for its coupling with meshfree discretizations. We exploit the strengths of both methods by using IGA to provide a smooth, geometrically-exact surface discretization of the problem domain boundary, while the Reproducing Kernel Particle Method (RKPM) discretization is used to provide the volumetric discretization of the domain interior. The coupling strategy is based upon the higher-order consistency or reproducing conditions that are directly imposed in the physical domain. The resulting coupled method enjoys several favorable features: (i) it preserves the geometric exactness of IGA, (ii) it circumvents the need for global volumetric parameterization of the problem domain, (iii) it achieves arbitrary-order approximation accuracy while preserving higher-order smoothness of the discretization. Several numerical examples are solved to show the optimal convergence properties of the coupled IGA–RKPM formulation, and to demonstrate its effectiveness in constructing volumetric discretizations for complex-geometry objects. As for the next contribution, we exploit the use of smooth, high-order spline basis functions in IGA to solve high-order surface PDEs governing the morphological evolution of vesicles. These governing equations are often consisted of geometric PDEs, high-order PDEs on stationary or evolving surfaces, or a combination of them. We propose an isogeometric formulation for solving these PDEs. In the context of geometric PDEs, we consider phase-field approximations of mean curvature flow and Willmore flow problems and numerically study the convergence behavior of isogeometric analysis for these problems. As a model problem for high-order PDEs on stationary surfaces, we consider the Cahn–Hilliard equation on a sphere, where the surface is modeled using a phase-field approach. As for the high-order PDEs on evolving surfaces, a phase-field model of a deforming multi-component vesicle, which consists of two fourth-order nonlinear PDEs, is solved using the isogeometric analysis in a primal variational framework. Through several numerical examples in 2D, 3D and axisymmetric 3D settings, we show the robustness of IGA for solving the considered phase-field models. Finally, we present a monolithic, implicit formulation based on isogeometric analysis and generalized-alpha time integration for simulating hydrodynamics of vesicles according to a phase-field model. Compared to earlier works, the number of equations of the phase-field model which need to be solved is reduced by leveraging high continuity of NURBS functions, and the algorithm is extended to 3D settings. We use residual-based variational multi-scale method (RBVMS) for solving Navier–Stokes equations, while the rest of PDEs in the phase-field model are treated using a standard Galerkin-based IGA. We introduce the resistive immersed surface (RIS) method into the formulation which can be employed for an implicit description of complex geometries using a diffuse-interface approach. The implementation highlights the robustness of the RBVMS method for Navier–Stokes equations of incompressible flows with non-trivial localized forcing terms including bending and tension forces of the vesicle. The potential of the phase-field model and isogeometric analysis for accurate simulation of a variety of fluid-vesicle interaction problems in 2D and 3D is demonstrated. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,1 KW - Phasenfeldmodell KW - Vesikel KW - Hydrodynamik KW - Multiphysics KW - Isogeometrische Analyse KW - Isogeometric Analysis KW - Vesicle dynamics KW - Phase-field modeling KW - Geometric Partial Differential Equations KW - Residual-based variational multiscale method Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220114-45658 ER - TY - THES A1 - Shaaban Mohamed, Ahmed Mostafa T1 - Isogeometric boundary element analysis and structural shape optimization for Helmholtz acoustic problems N2 - In this thesis, a new approach is developed for applications of shape optimization on the time harmonic wave propagation (Helmholtz equation) for acoustic problems. This approach is introduced for different dimensional problems: 2D, 3D axi-symmetric and fully 3D problems. The boundary element method (BEM) is coupled with the isogeometric analysis (IGA) forming the so-called (IGABEM) which speeds up meshing and gives higher accuracy in comparison with standard BEM. BEM is superior for handling unbounded domains by modeling only the inner boundaries and avoiding the truncation error, present in the finite element method (FEM) since BEM solutions satisfy the Sommerfeld radiation condition automatically. Moreover, BEM reduces the space dimension by one from a volumetric three-dimensional problem to a surface two-dimensional problem, or from a surface two-dimensional problem to a perimeter one-dimensional problem. Non-uniform rational B-splines basis functions (NURBS) are used in an isogeometric setting to describe both the CAD geometries and the physical fields. IGABEM is coupled with one of the gradient-free optimization methods, the Particle Swarm Optimization (PSO) for structural shape optimization problems. PSO is a straightforward method since it does not require any sensitivity analysis but it has some trade-offs with regard to the computational cost. Coupling IGA with optimization problems enables the NURBS basis functions to represent the three models: shape design, analysis and optimization models, by a definition of a set of control points to be the control variables and the optimization parameters as well which enables an easy transition between the three models. Acoustic shape optimization for various frequencies in different mediums is performed with PSO and the results are compared with the benchmark solutions from the literature for different dimensional problems proving the efficiency of the proposed approach with the following remarks: - In 2D problems, two BEM methods are used: the conventional isogeometric boundary element method (IGABEM) and the eXtended IGABEM (XIBEM) enriched with the partition-of-unity expansion using a set of plane waves, where the results are generally in good agreement with the linterature with some computation advantage to XIBEM which allows coarser meshes. -In 3D axi-symmetric problems, the three-dimensional problem is simplified in BEM from a surface integral to a combination of two 1D integrals. The first is the line integral similar to a two-dimensional BEM problem. The second integral is performed over the angle of revolution. The discretization is applied only to the former integration. This leads to significant computational savings and, consequently, better treatment for higher frequencies over the full three-dimensional models. - In fully 3D problems, a detailed comparison between two BEM methods: the conventional boundary integral equation (CBIE) and Burton-Miller (BM) is provided including the computational cost. The proposed models are enhanced with a modified collocation scheme with offsets to Greville abscissae to avoid placing collocation points at the corners. Placing collocation points on smooth surface enables accurate evaluation of normals for BM formulation in addition to straightforward prediction of jump-terms and avoids singularities in $\mathcal{O} (1/r)$ integrals eliminating the need for polar integration. Furthermore, no additional special treatment is required for the hyper-singular integral while collocating on highly distorted elements, such as those containing sphere poles. The obtained results indicate that, CBIE with PSO is a feasible alternative (except for a small number of fictitious frequencies) which is easier to implement. Furthermore, BM presents an outstanding treatment of the complicated geometry of mufflers with internal extended inlet/outlet tube as an interior 3D Helmholtz acoustic problem instead of using mixed or dual BEM. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,6 KW - Randelemente-Methode KW - Isogeometrische Analyse KW - Gestaltoptimierung KW - Boundary Element Method KW - Isogeometric Analysis KW - Helmholtz Acoustic Problems KW - Shape Optimization Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220816-47030 ER -