TY - THES A1 - Hatahet, Tareq T1 - On the Analysis of the Disproportionate Structural Collapse in RC Buildings N2 - Increasing structural robustness is the goal which is of interest for structural engineering community. The partial collapse of RC buildings is subject of this dissertation. Understanding the robustness of RC buildings will guide the development of safer structures against abnormal loading scenarios such as; explosions, earthquakes, fine, and/or long-term accumulation effects leading to deterioration or fatigue. Any of these may result in local immediate structural damage, that can propagate to the rest of the structure causing what is known by the disproportionate collapse. This work handels collapse propagation through various analytical approaches which simplifies the mechanical description of damaged reinfoced concrete structures due to extreme acidental event. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2018,2 KW - Beton KW - disproportionate collapse KW - buildings KW - reinforced concrete KW - catenary action KW - compressive arching KW - dynamic amplifification KW - structural robustness Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20180329-37405 ER - TY - THES A1 - Zhu, Pengtao T1 - The Variability of the Void Ratio of Sand and its Effect on Settlement and Infinite Slope Stability N2 - The uncertainty of a soil property can significantly affect the physical behavior of soil, so as to influence geotechnical practice. The uncertainty can be expressed by its stochastic parameters, including the mean, the standard deviation, and the spatial correlation length. These stochastic parameters are regarded as constant value in most of the former studies. The main aim of this thesis is to prove whether they are depth-dependent, and to evaluate the effect of this depth-dependent character on both the settlement and the infinite slope stability during rainwater infiltration. A stochastic one-dimensional settlement simulation is carried out using random finite element method with the von Wolffersdorff hypoplastic model, so as to evaluate the effect of stress level on the stochastic parameters of void ratio related parameters of sand. It is found that these stochastic parameters are both stress-dependent and depth-dependent. The non-stationary random field, considering the depth-dependent character of these stochastic parameters, can be generated through the distortion of the stationary random field. The one-dimensional settlement analysis is carried out to evaluation the effect of the depth-dependent character of the stochastic parameters of void ratio on the strain. It is found that the depth-dependent character has low effect on the strain. The deterministic analysis of infinite slope stability during rainwater infiltration is simulated. The transient seepage is carried out using finite difference method, while the steady state seepage is simulated using the analytical solution. The saturated hydraulic conductivity (ks) is taken as the only variable. The results show that the depth-dependent ks has a significant influence on the stability of the slope when the negative flux is high. Without considering the depth-dependent character, can overestimate the factor of safety of the slope. A slope can fail if the depth-dependent character is considered, while it is stable if the depth-dependent character is neglected. The failure time of the slope with a greater depth-dependent ks is earlier during transient infiltration. Meanwhile, the stochastic infinite slope stability analysis during infiltration, is also carried out to highlight the effect of the depth-dependent character of the stochastic parameters of ks. The results show that: the probability of failure is significantly increased if the depth-dependent character of mean is considered, while, it is moderately reduced if the depth-dependent character of the standard deviation is accounted. If the depth-dependent character of both the mean and standard deviation of ks is considered, the depth-dependent mean value plays a dominant influence on the results. Furthermore, the depth-dependent character of the spatial correlation length can slightly reduce the probability of failure. T3 - Schriftenreihe Geotechnik - 29 KW - Bodenunruhe KW - Erdrutsch KW - Versickerung KW - Statistische Analyse KW - soil heterogeneity KW - landslide KW - seepage KW - statistical analysis Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20180403-37411 ER - TY - THES A1 - Seiffarth, Torsten T1 - Sorptionsverhalten von Cu2+ und NH4+ an Bentoniten unter Berücksichtigung von Nebengemengteilen sowie Strukturänderungen nach moderater Wärmebehandlung N2 - Bentonite sind quellfähige Tone, die häufig in der Umwelttechnik (in Abdichtungsbauwerken oder in der Bodensanierung) eingesetzt werden. Ziel der Arbeit war die Klärung, wie eine unterschiedliche Kationenbelegung mit Cu2+ und NH4+ die Eigenschaften der Bentonite bei Raumtemperatur und nach moderater Wärmebehandlung (300 – 450°C) beeinflusst. Im Blickpunkt stand insbesondere die gleichzeitige Präsenz von Kupfer- und Ammoniumionen, die als Vertreter für häufig auftretende Inhaltsstoffe von Wässern in der Umgebung von technischen Bentoniten ausgewählt wurden. Die Untersuchungen zur Cu2+-Sorption bei Raumtemperatur und nach moderater Wärmebehandlung (300 – 450°C) erfolgten an Pulverproben von zwei technischen Bentoniten, die sich in der ursprünglichen Kationenbelegung, Art und Anteil an Nebengemengteilen, sowie der Schichtladungsverteilung in den Montmorilloniten unterscheiden. Vor der Wärmebehandlung wurden die Bentonite durch Kontakt mit verschieden konzentrierten Kupfer- und Ammoniumlösungen mit unterschiedlichen Gehalten der Kationen Cu2+, NH4+, Na+, Ca2+, Mg2+ belegt. Der Eintrag von Kupferionen in die Bentonite durch Kationenaustausch bei Raumtemperatur wurde erwartungsgemäß durch präsente Nebengemengteile (wie Carbonat) beeinflusst, so dass die Kupferionen zusätzlich spezifisch adsorbiert und in festen Phasen angereichert wurden. Die Cu2+-Fixierung infolge der Wärmebehandlung wurde vom Cu2+-Totalgehalt in den Bentoniten, der Präsenz von Nebengemengteilen und die Schichtladungsverteilung in den Montmorilloniten beeinflusst. Es waren generell Behandlungstemperaturen von > 400°C erforderlich, um Cu2+-Fixierungsraten von > 95% zu erzielen. Waren während der Wärmebehandlung neben Cu2+-Ionen gleichzeitig NH4+-Ionen in den Bentoniten präsent, konnte die Cu2+-Fixierungstemperatur herabgesetzt werden. Die Deammonisierung (NH4+ --> NH3 + H+) der NH4+-belegten Bentonite fand größtenteils unterhalb der Dehydroxylierungstemperatur der Bentonite statt. Durch Untersuchungen (XRD, FTIR, NMR, ESR) zum Mechanismus der Cu2+-Einbindung in die Bentonite an speziell aufbereiteten Proben (carbonatfrei, < 2 µm) konnte nachgewiesen werden, dass in den Cu2+-belegten Montmorilloniten die Cu2+-Ionen infolge der Wärmebehandlung nicht bis in die Oktaederschicht der Tonminerale vordringen, sondern nur bis in die Tetraederschicht wandern. In den NH4+-belegten Montmorilloniten treten im Zusammenhang mit der Deammonisierung keine zusätzlichen Strukturänderungen (wie Auflösung der Oktaederschicht) infolge der Wärmebehandlung auf. KW - Bentonit KW - Montmorillonite KW - Kupfersilicate KW - Sorption KW - Wärmebehandlung KW - Kupferfixierung KW - Deammonisierung KW - Kationenaustausch KW - Ammonium-Ton KW - Mikrostruktur Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20130718-19791 ER - TY - JOUR A1 - Schuch, Kai A1 - Kaps, Christian T1 - Maturation and Structure Formation Processes in Binders with Aqueous Alkali-Silicate Solutions N2 - Maturation and structure formation processes can lead to crack formation in silicate and aluminosilicate binders (e.g. for coating materials...) through restricted deformation, loss of strength and thus to loss of durability. These processes are evaluated with silicate materials with an outlook on aluminosilicate binders. KW - Waterglass KW - Silicate KW - Aluminosilicate KW - Geopolymer KW - Alkalisilicate KW - Aggregation KW - Geopolymer KW - Aluminosilicate KW - Coating Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170907-35979 N1 - First published in german language 28.07.2017 SP - 1 EP - 16 ER - TY - THES A1 - López Zermeño, Jorge Alberto T1 - Isogeometric and CAD-based methods for shape and topology optimization: Sensitivity analysis, Bézier elements and phase-field approaches N2 - The Finite Element Method (FEM) is widely used in engineering for solving Partial Differential Equations (PDEs) over complex geometries. To this end, it is required to provide the FEM software with a geometric model that is typically constructed in a Computer-Aided Design (CAD) software. However, FEM and CAD use different approaches for the mathematical description of the geometry. Thus, it is required to generate a mesh, which is suitable for FEM, based on the CAD model. Nonetheless, this procedure is not a trivial task and it can be time consuming. This issue becomes more significant for solving shape and topology optimization problems, which consist in evolving the geometry iteratively. Therefore, the computational cost associated to the mesh generation process is increased exponentially for this type of applications. The main goal of this work is to investigate the integration of CAD and CAE in shape and topology optimization. To this end, numerical tools that close the gap between design and analysis are presented. The specific objectives of this work are listed below: • Automatize the sensitivity analysis in an isogeometric framework for applications in shape optimization. Applications for linear elasticity are considered. • A methodology is developed for providing a direct link between the CAD model and the analysis mesh. In consequence, the sensitivity analysis can be performed in terms of the design variables located in the design model. • The last objective is to develop an isogeometric method for shape and topological optimization. This method should take advantage of using Non-Uniform Rational B-Splines (NURBS) with higher continuity as basis functions. Isogeometric Analysis (IGA) is a framework designed to integrate the design and analysis in engineering problems. The fundamental idea of IGA is to use the same basis functions for modeling the geometry, usually NURBS, for the approximation of the solution fields. The advantage of integrating design and analysis is two-fold. First, the analysis stage is more accurate since the system of PDEs is not solved using an approximated geometry, but the exact CAD model. Moreover, providing a direct link between the design and analysis discretizations makes possible the implementation of efficient sensitivity analysis methods. Second, the computational time is significantly reduced because the mesh generation process can be avoided. Sensitivity analysis is essential for solving optimization problems when gradient-based optimization algorithms are employed. Automatic differentiation can compute exact gradients, automatically by tracking the algebraic operations performed on the design variables. For the automation of the sensitivity analysis, an isogeometric framework is used. Here, the analysis mesh is obtained after carrying out successive refinements, while retaining the coarse geometry for the domain design. An automatic differentiation (AD) toolbox is used to perform the sensitivity analysis. The AD toolbox takes the code for computing the objective and constraint functions as input. Then, using a source code transformation approach, it outputs a code for computing the objective and constraint functions, and their sensitivities as well. The sensitivities obtained from the sensitivity propagation method are compared with analytical sensitivities, which are computed using a full isogeometric approach. The computational efficiency of AD is comparable to that of analytical sensitivities. However, the memory requirements are larger for AD. Therefore, AD is preferable if the memory requirements are satisfied. Automatic sensitivity analysis demonstrates its practicality since it simplifies the work of engineers and designers. Complex geometries with sharp edges and/or holes cannot easily be described with NURBS. One solution is the use of unstructured meshes. Simplex-elements (triangles and tetrahedra for two and three dimensions respectively) are particularly useful since they can automatically parameterize a wide variety of domains. In this regard, unstructured Bézier elements, commonly used in CAD, can be employed for the exact modelling of CAD boundary representations. In two dimensions, the domain enclosed by NURBS curves is parameterized with Bézier triangles. To describe exactly the boundary of a two-dimensional CAD model, the continuity of a NURBS boundary representation is reduced to C^0. Then, the control points are used to generate a triangulation such that the boundary of the domain is identical to the initial CAD boundary representation. Thus, a direct link between the design and analysis discretizations is provided and the sensitivities can be propagated to the design domain. In three dimensions, the initial CAD boundary representation is given as a collection of NURBS surfaces that enclose a volume. Using a mesh generator (Gmsh), a tetrahedral mesh is obtained. The original surface is reconstructed by modifying the location of the control points of the tetrahedral mesh using Bézier tetrahedral elements and a point inversion algorithm. This method offers the possibility of computing the sensitivity analysis using the analysis mesh. Then, the sensitivities can be propagated into the design discretization. To reuse the mesh originally generated, a moving Bézier tetrahedral mesh approach was implemented. A gradient-based optimization algorithm is employed together with a sensitivity propagation procedure for the shape optimization cases. The proposed shape optimization approaches are used to solve some standard benchmark problems in structural mechanics. The results obtained show that the proposed approach can compute accurate gradients and evolve the geometry towards optimal solutions. In three dimensions, the moving mesh approach results in faster convergence in terms of computational time and avoids remeshing at each optimization step. For considering topological changes in a CAD-based framework, an isogeometric phase-field based shape and topology optimization is developed. In this case, the diffuse interface of a phase-field variable over a design domain implicitly describes the boundaries of the geometry. The design variables are the local values of the phase-field variable. The descent direction to minimize the objective function is found by using the sensitivities of the objective function with respect to the design variables. The evolution of the phase-field is determined by solving the time dependent Allen-Cahn equation. Especially for topology optimization problems that require C^1 continuity, such as for flexoelectric structures, the isogeometric phase field method is of great advantage. NURBS can achieve the desired continuity more efficiently than the traditional employed functions. The robustness of the method is demonstrated when applied to different geometries, boundary conditions, and material configurations. The applications illustrate that compared to piezoelectricity, the electrical performance of flexoelectric microbeams is larger under bending. In contrast, the electrical power for a structure under compression becomes larger with piezoelectricity. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,4 KW - CAD KW - Gestaltoptimierung KW - Topologieoptimierung KW - Isogeometrische Analyse KW - Finite-Elemente-Methode KW - Computer-Aided Design KW - Shape Optimization KW - Topology Optimization KW - Isogeometric Analysis KW - Finite Element Method Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220831-47102 ER - TY - THES A1 - Shaaban Mohamed, Ahmed Mostafa T1 - Isogeometric boundary element analysis and structural shape optimization for Helmholtz acoustic problems N2 - In this thesis, a new approach is developed for applications of shape optimization on the time harmonic wave propagation (Helmholtz equation) for acoustic problems. This approach is introduced for different dimensional problems: 2D, 3D axi-symmetric and fully 3D problems. The boundary element method (BEM) is coupled with the isogeometric analysis (IGA) forming the so-called (IGABEM) which speeds up meshing and gives higher accuracy in comparison with standard BEM. BEM is superior for handling unbounded domains by modeling only the inner boundaries and avoiding the truncation error, present in the finite element method (FEM) since BEM solutions satisfy the Sommerfeld radiation condition automatically. Moreover, BEM reduces the space dimension by one from a volumetric three-dimensional problem to a surface two-dimensional problem, or from a surface two-dimensional problem to a perimeter one-dimensional problem. Non-uniform rational B-splines basis functions (NURBS) are used in an isogeometric setting to describe both the CAD geometries and the physical fields. IGABEM is coupled with one of the gradient-free optimization methods, the Particle Swarm Optimization (PSO) for structural shape optimization problems. PSO is a straightforward method since it does not require any sensitivity analysis but it has some trade-offs with regard to the computational cost. Coupling IGA with optimization problems enables the NURBS basis functions to represent the three models: shape design, analysis and optimization models, by a definition of a set of control points to be the control variables and the optimization parameters as well which enables an easy transition between the three models. Acoustic shape optimization for various frequencies in different mediums is performed with PSO and the results are compared with the benchmark solutions from the literature for different dimensional problems proving the efficiency of the proposed approach with the following remarks: - In 2D problems, two BEM methods are used: the conventional isogeometric boundary element method (IGABEM) and the eXtended IGABEM (XIBEM) enriched with the partition-of-unity expansion using a set of plane waves, where the results are generally in good agreement with the linterature with some computation advantage to XIBEM which allows coarser meshes. -In 3D axi-symmetric problems, the three-dimensional problem is simplified in BEM from a surface integral to a combination of two 1D integrals. The first is the line integral similar to a two-dimensional BEM problem. The second integral is performed over the angle of revolution. The discretization is applied only to the former integration. This leads to significant computational savings and, consequently, better treatment for higher frequencies over the full three-dimensional models. - In fully 3D problems, a detailed comparison between two BEM methods: the conventional boundary integral equation (CBIE) and Burton-Miller (BM) is provided including the computational cost. The proposed models are enhanced with a modified collocation scheme with offsets to Greville abscissae to avoid placing collocation points at the corners. Placing collocation points on smooth surface enables accurate evaluation of normals for BM formulation in addition to straightforward prediction of jump-terms and avoids singularities in $\mathcal{O} (1/r)$ integrals eliminating the need for polar integration. Furthermore, no additional special treatment is required for the hyper-singular integral while collocating on highly distorted elements, such as those containing sphere poles. The obtained results indicate that, CBIE with PSO is a feasible alternative (except for a small number of fictitious frequencies) which is easier to implement. Furthermore, BM presents an outstanding treatment of the complicated geometry of mufflers with internal extended inlet/outlet tube as an interior 3D Helmholtz acoustic problem instead of using mixed or dual BEM. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,6 KW - Randelemente-Methode KW - Isogeometrische Analyse KW - Gestaltoptimierung KW - Boundary Element Method KW - Isogeometric Analysis KW - Helmholtz Acoustic Problems KW - Shape Optimization Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220816-47030 ER - TY - THES A1 - Peters, Simone T1 - The Influence of Power Ultrasound on Setting and Strength Development of Cement Suspensions N2 - Ein aktuelles Thema in der Forschung der Betonindustrie ist die gezielte Steuerung des Erstarrens und der Entwicklung der (Früh)Festigkeit von Betonen und Mörteln. Aus ökonomischer Sicht sind außerdem die Reduktion der CO2-Emission und die Schonung von Ressourcen und Energie wichtige Forschungsschwerpunkte. Eine Möglichkeit zum Erreichen dieser Ziele ist es, die Reaktivität/Hydratation der silikatischen Klinkerphasen gezielt anzuregen. Neben den bereits bekannten Möglichkeiten der Hydratationsbeschleunigung (u.a. Wärmebehandlung, Zugabe von Salzen) bietet die Anwendung von Power-Ultraschall (PUS) eine weitere Alternative zur Beschleunigung der Zementhydratation. Da bis zum jetzigen Zeitpunkt noch keine Erfahrungen zum Einsatz von PUS in der Zementchemie vorliegen, sollen mit der vorliegenden Arbeit grundlegende Kenntnisse zum Einfluss von PUS auf das Fließ- und Erstarrungsverhalten von Zementsuspensionen erarbeitet werden. Dazu wurde die Arbeit in fünf Hauptuntersuchungsabschnitte aufgeteilt. Im ersten Teil wurden optimale PUS-Parameter wie Amplitude und Energieeintrag ermittelt, die eine effiziente Beschleunigung der Portlandzement(CEM I)hydratation bei kurzen Beschallzeiten und begrenzter Zementleimtemperaturerhöhung erlauben. Mit Hilfe unabhängiger Untersuchungsmethoden (Bestimmung des Erstarrungsbeginns, der Festigkeitsentwicklung, zerstörungsfreier Ultraschallprüfung, isothermer Wärmeflusskalorimetrie, hochauflösender Rasterelektronmikroskopie (REM) wurde die Wirkung von PUS auf den Hydratationsverlauf von CEM I-Suspensionen charakterisiert. Die Ergebnisse zeigen, dass die Behandlung von CEM I-Suspensionen mit PUS grundsätzlich ein beschleunigtes Erstarren und eine beschleunigte (Früh)Festigkeitsentwicklung hervorruft. Anhand von REM-Untersuchungen konnte eindeutig nachgewiesen werden, dass die Beschleunigung der CEM I-Hydratation mit einer beschleunigten Hydratation der Hauptklinkerphase Alit korreliert. Auf Grundlage dieser Erkenntnisse wurden die Ursachen der Aktivierung der Alithydratation untersucht. Dazu wurden Untersuchungen an Einzelsystemen des CEM I (silikatische Klinkerphase) durchgeführt. Es ist bekannt, das die Hydratation der Hauptklinkerphase Alit (in der reinen Form Tricalciumsilikat 3CaO*SiO2; C3S) durch Lösungs-/Fällungsreaktionen (Bildung von Calcium-Silikat-Hydrat Phasen, C-S-H Phasen) bestimmt wird. Mit Hilfe von Untersuchungen zur Auflösung (C3S) und Kristallbildung (C-S-H Phasen) in Lösungen und Suspensionen (Aufzeichnung der elektrischen Leitfähigkeit sowie Bestimmung der Ionenkonzentrationen der wässrigen Phase, REM-Charakterisierung der Präzipitate) wurde die Beeinflussung dieser durch eine PUS-Behandlung charakterisiert. Die Ergebnisse zeigen, dass in partikelfreien Lösungen (primäre Keimbildung) eine PUS-Behandlung keinen Einfluss auf die Kinetik der Kristallisation von C-S-H Phasen hervorruft. Das heißt, auch die durch PUS eingetragene Energie reicht offensichtlich nicht aus, um in Abwesenheit von Oberflächen die C-S-H Phasen Bildung zu beschleunigen. Das weist darauf hin, dass die Bildung von C-S-H Phasen nicht durch eine Beschleunigung von Ionen in der Lösung (erhöhte Diffusion durch Anwendung von PUS) hervorgerufen wird. Eine Beschleunigung des Kristallisationsprozesses (Keimbildung und Wachstum von C-S-H Phasen) durch PUS wird nur in Anwesenheit von Partikeln in der Lösung (Suspension) erzielt. Das belegen Ergebnisse, bei denen die Bildung erster C-S-H Phasen bei geringer Übersättigung (heterogene Keimbildung, in Anwesenheit von Oberflächen) erfolgt. Unter diesen Bedingungen konnte gezeigt werden, dass PUS innerhalb der ersten 30 Minuten der Hydratation eine erhöhte Fällung von ersten C-S-H Phasen bewirkt. Diese fungieren dann vermutlich während der Haupthydratation als Keim bzw. geeignete Oberfläche zum beschleunigten Aufwachsen von weiteren C-S-H Phasen. Weiterhin ist vorstellbar, dass (in Analogie zu anderen Bereichen der Sonochemie) PUS durch Kavitation Schockwellen hervorruft, welche Partikel und wässriges Medium beschleunigen und damit erhöhte Partikelbewegungen und -kollisionen induziert. Dies wiederum bewirkt, dass die anfänglich auf der C3S-Oberfläche gebildeten C-S-H Phasen teilweise wieder entfernt werden. Damit ist das Inlösunggehen von Ca- und Si-Ionen aus dem C3S weiterhin möglich. Um den genauen Mechanismus weiter zu charakterisieren sollten mit geeigneten Methoden weitere Untersuchungen durchgeführt werden. Im zweiten Teil der Arbeit wurde der Einfluss von PUS auf das Fließverhalten von CEM I-Suspensionen untersucht. Aus der Anwendung von PUS in anderen technischen Bereichen sind unter anderem Effekte wie das Entlüften, das Homogenisieren und das Dispergieren von Suspensionen und Emulsionen mittels PUS bekannt. Mit Hilfe der Bestimmung des Luftporengehaltes, Sedimentationsversuchen und cryo-SEM Untersuchungen wurde der Einfluss von PUS auf CEM I-Suspensionen charakterisiert. Die Ergebnisse belegen, dass durch PUS eine verbesserte Homogenität und Dispergierung der CEM I-Suspension erzielt wird. Damit wird für CEM I-Suspensionen unterschiedlichster w/z-Werte eine verbesserte Fließfähigkeit festgestellt. Ergebnisse der Bestimmung von Ausbreitmaßen und Trichterauslaufzeiten zeigen, dass PUS einen direkten Einfluss vor allem auf die Viskosität der CEM I-Suspensionen besitzt. Werden Fließmitteln (FM) der CEM I-Suspension zugegeben, wird nicht in jedem Fall eine verbesserte Fließfähigkeit festgestellt. Hier scheint unter bestimmten Voraussetzungen (w/z-Wert, FM-Gehalt, PUS) die Reaktion zwischen Aluminat- und Sulfatphase des Klinkers gestört. Zur eindeutigen Klärung dieses Sachverhaltes bedarf es jedoch weiterer quantitativer Untersuchungen zum Reaktionsumsatz. Im dritten Teil der Arbeit wurden die am CEM I gewonnenen Erkenntnisse zum Einfluss von PUS auf die Hydratation an Portland-Hüttensand(HÜS)-Zement-Systemen verifiziert. Dafür wurden auch in diesem Teil der Arbeit zunächst die optimalen PUS-Parameter festgelegt und der Einfluss auf das Erstarrung- und Erhärtungsverhalten dokumentiert. Untersuchungsmethoden sind unter anderem die Bestimmung des Erstarrungsbeginns und der (Früh)Festigkeitsentwicklung, Temperaturaufzeichnungen und isothermale Wärmeflusskalorimetrie sowie REM. Die Ergebnisse zeigen, dass auch die Reaktion von HÜS-Zementen durch PUS beschleunigt wird. Weiterführende Untersuchungen belegen, dass die erzielte Beschleunigung vorwiegend auf der Beschleunigung der Alitkomponente des CEM I beruht. Im Fokus der Teile vier und fünf dieser Arbeit stand die Anwendbarkeit der PUS-Technik unter praktischen Bedingungen. Zum einen wurde die Anwendbarkeit von PUS in fertig gemischten Mörteln beurteilt. Anhand des Vergleichs wichtiger Frisch- und Festmörteleigenschaften unterschiedlich hergestellter Mörtel (beschallt im Anschluss an konventionelle Mischtechnik, beschallt im Anschluss an Suspensionsmischtechnik mit anschließender Zumischung der Gesteinskörnung und nicht beschallt) wird gezeigt, dass im Fall von Mörteln mit hohem Leimanteil eine durch PUS induzierte beschleunigte Festigkeitsentwicklung auch mit herkömmlichen Mischabläufen (ohne aufwendige Umstellung des Mischprozesses) möglich ist. Abschließend wird untersucht, ob der Herstellungsprozess von Wandbauteilen im Fertigteilwerk durch den Einsatz von PUS optimiert werden kann und ob eine Einbindung der PUS-Technik in den Fertigungsprozess ohne größeren Aufwand möglich ist. Dazu wurden in einem ersten Schritt die Frisch- und Festbetoneigenschaften eines aktuell angewendeten selbstverdichtenden Betons im Labormaßstab (Mörtel) in Abhängigkeit einer PUS-Behandlung dokumentiert und mit der seiner unbeschallten Referenz verglichen. Aufgrund der durch PUS verursachten verbesserten Fließ- und Festigkeitseigenschaften kann die beschallte Mörtelrezeptur hinsichtlich Fließmittelgehalt und Dauer der Wärmebehandlung optimiert werden. Somit werden ca. 30 % der Fließmittelzugabe und 40 % der Dauer der Wärmebehandlung eigespart. Eine Einbindung der PUS-Technik in das betrachtete Fertigteilwerk ist nach Überprüfung der konstruktiven Gegebenheiten der Fertigungsstrukturen ohne größeren Aufwand möglich. KW - Cement KW - Power Ultrasound KW - Acceleration KW - Tricalcium silicate Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170210-27446 SN - ISBN 978-3-00-055602-9 ER - TY - THES A1 - Schöler, Axel T1 - Hydration of multi-component cements containing clinker, slag, type-V fly ash and limestone N2 - Problemstellung und Zielsetzung 1. Die Herstellung von Portlandzementklinker trägt zu etwa 5 bis 8 % zur jährlichen Emissionsmenge an menschlich generiertem CO2 bei. Dies ist begründet in der Verwendung von fossilen Brennstoffen (ca. 40 % des gesamten CO2) und in der Entsäuerung des stark kalksteinhaltigen Rohmehls (ca. 60 % des gesamten CO2). 2. Verschiedene Strategien zur Verringerung des Ausstoßes an CO2 werden angewandt. Dies sind insbesondere die Optimierung der Prozessführung bei der Klinkerherstellung, die Verwendung alternativer Brennstoffe und die teilweise Substitution des Klinkeranteils in Zementen mit mehreren Hauptbestandteilen durch Zementersatzstoffe, sogenannte SCM (supplementary cementitious materials), wobei Hüttensand, Flugasche und Kalksteinmehl die meist verwendeten Materialien darstellen. 3. Durch die Reduktion des Klinkeranteils können quaternäre Systeme nicht nur einen Beitrag zur Reduzierung von CO2-Emissionen leisten. Ebenfalls ist es mit derartigen Systemen möglich Hüttensande und Flugaschen möglichst ökonomisch einzusetzen und gegebenenfalls auf Engpässe bei deren Verfügbarkeit zu reagieren. 4. Hüttensande und Flugaschen zeigen Ähnlichkeiten in ihrer prinzipiellen chemischen Zusammensetzung, so dass ähnliche Hydratphasen während ihrer Reaktion in Anwesenheit von Portlandzement gebildet werden können. Im Vergleich zu ternären Systemen, die neben Kalkstein auch Hüttensand oder Flugasche enthalten, kann bei quaternären Zementen, die neben Kalkstein sowohl Hüttensand als auch Flugasche enthalten, eine ähnliche Phasenentwicklung und damit auch ähnliche Festigkeitsentwicklung erwartet werden. 5. Die Verwendung von SCM als Zementersatzstoff ist durch die im Vergleich zu Portlandzement deutlich langsamere Reaktion und die dadurch bedingte ebenfalls langsamere Festigkeitsentwicklung begrenzt. Dies betrifft insbesondere die Entwicklung innerhalb der ersten 28 Tage. Dementsprechend ist es unerlässlich die Reaktivität von SCM wie Hüttensanden und Flugaschen eingehend zu untersuchen um die Reaktionsfähigkeit- und Geschwindigkeit und somit die Festigkeitsentwicklung zu steigern. 6. Die frühe Reaktion der Hauptklinkerphasen ist weitgehend untersucht und beschrieben, wobei entsprechende Studien meist hochverdünnte Modellsysteme betrachten. Jedoch gibt es kaum Hinweise inwiefern diese Erkenntnisse auf konzentrierte Systeme bei realistischen Wasser-Feststoff Verhältnissen übertragen werden können. Entsprechende Untersuchungen sind nötig um die Wechselwirkungen von Portlandzement und SCM in der Frühphase der Reaktion zu beschreiben. Stand der Wissenschaft 7. In verdünnten Systemen führt steigender Ca-Gehalt zu einer niedrigeren Auflösungsrate von C3S und C2S. 8. Bestimmende Faktoren der Auflösung von C3S sind sowohl die Untersättigung bezüglich C3S als auch die Übersättigung in Bezug auf C-S-H. 9. Erhöhte Al-Konzentrationen führen zur Verzögerung der Hydratation von C3S. Dies kann begründet sein durch die Einbindung von Al in C-S-H und eine dadurch bedingte deutlich langsamere Wachstumsrate von C-(A)-S-H. Ebenfalls scheint ein verzögernder Effekt von Al auf die Auflösung von C3S möglich. 10. Die Oberfläche von Kalkstein bietet besonders gute Bedingungen für die Keimbildung von C-S-H, so dass im Vergleich zu anderen SCM in Anwesenheit von Kalkstein deutlich mehr C-S-H Keime gebildet werden. 11. Die Reaktivität von Hüttensand und Flugasche wird einerseits durch die Korngrösse, andererseits jedoch auch durch die intrinsische Reaktivität des amorphen Anteils selbst bestimmt. 12. In amorphen (Calcium)Aluminosilikaten führt ein steigender Gehalt an Netzwerkmodifizierern, wie z.B. CaO, zu einem stärker depolymerisierten Glasnetzwerk und damit zu steigender Reaktivität. Die Wirkung von amphoteren Oxiden (Al2O3, Fe2O3) die sowohl als Netzwerkmodifizierer als auch als Netzwerkbildner auftreten können ist nicht vollständig geklärt. 13. CO2 haltige Monophasen besitzen im Vergleich zu Monosulfoaluminat eine höhere thermodynamische Stabilität, wodurch Ettringit stabilisiert wird. Durch das hohe spezifische Volumen von Ettringit wird ein Maximum an Raumausfüllung, dadurch eine geringere Porosität und in Folge ein Maximum an Festigkeit erreicht. 14. Kalkstein reagiert nur in geringem Ausmaß entsprechend dem zur Reaktion vorhandenen Al2O3, wobei sich zunächst Hemicarboaluminat, später Monocarboaluminat bildet. Dabei wird Al2O3 nicht nur durch den Portlandzement selbst, sondern auch durch die Auflösung von SCM, insbesondere von Flugasche, zur Verfügung gestellt. Methodik 15. Der Einfluss von SCM auf die frühe Hydratation von Portlandzement in binären (d.h. Hüttensand oder Flugasche oder Quarz) und ternären (d.h. Flugasche und Kalkstein) Systemen wurde mittels isothermer Kalorimetrie und Porenlösungsanalysen untersucht. Über die chemische Zusammensetzung der Porenlösung ermittelte Sättigungsindices und Löslichkeitsprodukte wurden in Bezug zur Wärmeentwicklung gesetzt. Basierend auf den ermittelten Daten wurde evaluiert, inwiefern Mechanismen die die Hydratation von reinen Klinkerphasen in verdünnten Systemen bestimmen ebenfalls in Zementpasten unter realistischen Bedingungen maßgebend sind. 16. Der Einfluss der chemischen Zusammensetzung auf die Reaktivität von Gläsern bei hohem pH (>13) wurde mittels Ionenchromatographie in hoch verdünnten Systemen untersucht. Puzzolanitätstests wurden an vereinfachten Modellsystemen sowie an Portlandzement-Glass-Systemen durchgeführt. Das Reaktionsverhalten der Gläser wurde über isotherme Kalorimetrie und thermogravimetrische Experimente untersucht. Über Massenbilanzkalkulationen kann der Gehalt an gebundenem Wasser in Funktion der Menge an reagiertem Glas berechnet werden. Ein Abgleich mit gebundenem Wasser bestimmt über thermogravimetrische Untersuchungen erlaubt es, den Reaktionsgrad der Gläser abzuschätzen. Zusätzliche Experimente mittels selektiver Lösung wurden zu Vergleichszwecken durchgeführt. 17. Die Reaktionskinetik von quaternären Pasten die sowohl Kalksteinmehl als auch Hüttensand und Flugasche enthalten wurden bis zum Alter von 28 Tagen mittels isothermer Kalorimetrie und Experimenten zum chemischen Schwinden untersucht. Ergänzend wurden Festigkeitsprüfungen an Mörtelprismen durchgeführt. 18. Quaternäre Pasten wurden ebenfalls hinsichtlich der gebildeten Hydratphasen bis zu einem Alter von 182 Tagen untersucht. Hierzu wurden basierend auf thermodynamischen Modellierungen volumetrische Berechnungen zum gesamten Phasenvolumen als Funktion des Kalkstein- und des Flugaschen- bzw. Hüttensandgehalts durchgeführt. Ergänzt durch thermogravimetrische Ermittlung des Gehalts an gebundenem Wasser und Portlandit, sowie mittels qualitativen röntgendiffraktometrischen Untersuchungen wurden die Ergebnisse der thermodynamischen Berechnungen mit der Festigkeitsentwicklung von Mörtelprismen abgeglichen. 19. Porenlösungen von quaternären Systemen wurden bis zu einem Alter von 728 Tagen mittels Ionenchromatographie und pH-Bestimmung analysiert. Über die ermittelten Konzentrationen wurden Sättigungsindices für relevante Phasen ermittelt. Im Hinblick auf den Einfluss des Hüttensandes wurden Porenlösungen für ausgewählte Systeme bei verschiedenen Hüttensandgehalten (20 und 30 M.%) bei 91 Tagen, sowie für die gesamten Matrix bis zu 91 Tagen, auf verschiedene Schwefelspecies untersucht. Im Wesentlichen erzielte Ergebnisse 20. Untersuchungen zur frühen Reaktionskinetik von binären Systemen zeigten einen stärkeren Wärmefluss in Anwesenheit von SCM, bedingt durch erhöhte für die Keimbildung zur Verfügung stehende Oberfläche sowie eine geringere (Über)Sättigung bezüglich C-S-H. Erhöhte Ca-Konzentrationen führten nicht zu langsamerer Auflösung von C3S, wie dies für reine Phasen bei hoher Verdünnung beobachtet wurde. Im Gegensatz zu Untersuchungen in Reinstsystemen führten höhere Ca-Konzentrationen nicht zu geringeren Reaktionsraten von C3S. Die schnellste Reaktion wurde bei Anwesenheit von Kalkstein, d.h. den höchsten Ca-Konzentrationen, beobachtet. Die grundsätzliche Reaktionscharakteristik zeigt einen inversen Bezug zur Untersättigung bezüglich C3S, wobei höhere Untersättigung zu schnellerer Reaktion führt. Wie ebenfalls in Reinstsystemen bei hoher Verdünnung beobachtet, führt die Anwesenheit von Aluminium zur Verzögerung der Reaktion. Höhere SO42–-Konzentrationen wurden in Anwesenheit von Flugasche beobachtet was die Ettringitausfällung verhinderte und zu höheren Al-Konzentrationen führt. Dieser Mechanismus führt zu höheren Al-Konzentrationen in Gegenwart von Quarz, Hüttensand und Kalkstein im Gegensatz zu Anwesenheit von Flugasche. 21. Die frühe Hydratation von quaternären Systemen wird in Anwesenheit von Kalkstein deutlich beschleunigt, während Flugasche zu einer Verzögerung führt. Im Gegensatz zu einem Referenzsystem mit inertem Quarz konnte mittels isothermer Kalorimetrie und chemischem Schwinden eine Reaktionsbeschleunigung in Anwesenheit von Hüttensand nachgewiesen werden. Weitere Zugaben an Flugasche, Kalkstein oder Mischungen von beiden führten zu einer weiteren Beschleunigung, wobei die Unterschiede zwischen diesen Materialien zu gering sind um eine klare Unterscheidung zu ermöglichen. 22. Bei allen zur Glasauflösung- bzw. Reaktivität durchgeführten Experimenten zeigten sich identische Trends, d.h. steigende Reaktivität und Auflösungsgeschwindigkeit mit steigendem Anteil an Netzwerkmodifizierern innerhalb der Glasstruktur. Die Ergebnisse weisen darauf hin, dass Al2O3 in sämtlichen betrachteten Glaszusammensetzungen vorwiegend als Netzwerkmodifizierer vorliegt. Die thermogravimetrische Bestimmung von gebundenem Wasser bei den Modellsystemen und den glashaltigen Zementen kann über Massenbilanzberechnungen als Funktion des Anteils an reagiertem Glas zur Abschätzung des Glasreaktionsgrades verwendet werden. 23. Zu frühen Zeiten von bis zu 7 Tagen hat der Anteil an Hüttensand, Flugasche oder Kalkstein keinen wesentlichen Einfluss auf die Festigkeitsentwicklung. Zu späteren Zeiten wurde über thermodynamische Berechnungen ein Reaktionsgrad des enthaltenen CaCO3 (Calcit) von 2 bis 5 M.% ermittelt. Dies führt zur Bildung von Hemicarboaluminat und Monocarboaluminat wodurch Ettringit indirekt stabilisiert wird. In Folge ergibt sich ein höheres absolutes Volumen der gebildeten Hydratphasen und damit höhere Festigkeiten wie Festigkeitsuntersuchungen an Mörtelprismen zeigen. Dabei hängt der Reaktionsgrad des CaCO3 vom verfügbaren Al2O3 ab, welches neben dem Portlandzement selbst auch durch die Reaktion von Hüttensand, im Besonderen aber durch die Auflösung der Flugasche zur Verfügung steht. 24. Allgemein hat die Anwesenheit von Hüttensand und Flugasche in Gegenwart von Kalkstein wenig Einfluss auf die gebildeten Hydratphasen. Die sukzessive Substitution von Hüttensand durch Flugasche führt zu einer geringen Abnahme von Portlandit und C-S-H und begünstigt die Bildung von mehr Monocarboaluminat und Hemicarboaluminat. Portlandit reagiert puzzolanisch mit der Flugasche wobei sich C-S-H bildet. Dennoch führt die geringe Reaktivität der Flugasche zu geringerem Gehalt an C-S-H was wiederrum sinkendes gesamtes Hydratphasenvolumen und damit niedrigere Festigkeitswerte generiert. Allerdings ist der Einfluss gering und alle untersuchten Systeme erreichen die Festigkeitsklasse 42.5 N entsprechend EN 196-1. 25. Analog zur Hydratphasenbildung zeigten Untersuchungen der Porenlösungschemie von quaternären Systemen durchweg ähnliche Ergebnisse. Entsprechend dem Gehalt an Flugasche sind die stärksten Variationen in den Al-Konzentrationen zu verzeichnen, welche mit steigendem Gehalt an Flugasche und mit fortschreitender Hydratation ansteigen. Weiterhin ist zu späteren Zeiten Portlandit bei hohen Gehalten an Flugasche zusehends untersättigt, während die Untersättigung bezüglich Strätlingit abnimmt, was auf die Auflösung von Portlandit hinweist. 26. Der absolute Gehalt an SO3 in der Porenlösung wird dominiert von Sulfat (SO42–), während die Konzentrationen von Sulfit (SO32–) und Thiosulfat (S2O32–) sehr niedrig waren. Nach 2 Tagen lagen ca. 90 % des gesamten Schwefels in Form von SO42– vor. Nach 91 Tagen waren dies ca. 36 % während ca. 28 % als S2O32– vorlagen. Bei höheren Gehalten an Hüttensand sind dabei nach 7 Tagen höhere Konzentrationen an SO32– und S2O32– feststellbar. N2 - Problem definition and research objectives 1. The production of Portland cement clinker causes approx. 5% to 8% of the annual man-made CO2 emissions. This is due to the usage of mainly fossil fuel (approx. 40 % of the total CO2) and because of the decarbonation of limestone as a main component of the raw meal (approx. 60 % of the total CO2). 2. Various strategies are applied in order to reduce the green-house gas-emissions, such as optimizing the process of clinker production, the use of alternative fuel and the partial substitution of the clinker in blended cement by so-called SCM (supplementary cementitious materials). Hereby blast-furnace slag, fly ash and limestone are the most used materials. 3. Quaternary systems containing three SCM simultaneously besides Portland cement contribute to the reduction of CO2 emissions due to the decrease of the clinker content. In addition, such systems allow to use blast-furnace slag and fly ash in the most economical way and provide the possibility to account for shortages of SCM on the market. 4. Blast-furnace slag and fly ash show similarities in their principal chemical compositions such that similar hydrates are formed during their reaction in presence of Portland cement. Compared to ternary systems based on blast-furnace slag or fly ash besides limestone, quaternary systems that contain both, blast-furnace slag and fly ash, simultaneously besides limestone, are expected to perform similar in terms of phase assemblage and strength development. 5. The use of SCM as cement replacing materials is limited due to their generally slower reaction compared to neat cement which also leads to lower strength development, especially in the early stage of the hydration up to 28 d. To account for this it is necessary to study the reactivity of SCM such as blast-furnace slag and fly ash in detail in order to develop strategies to enhance the reactivity and thereby the strength development of SCM-containing systems. 6. The early hydration of clinker phases is studied in detail, mainly in diluted systems. It is unclear if processes that were found to control the reaction of such model systems are also prevailing in concentrated cement pastes under realistic water-to-solid ratios. Deeper insight to this aspect is needed to better understand interactions of neat Portland cement and SCM in the first hours of hydration. State-of-the-art 7. Increasing Ca-concentrations lead to decreasing dissolution rates of C3S and C2S in diluted systems. 8. The hydration kinetics of C3S is controlled by the interplay of undersaturation with respect to C3S and oversaturation with respect to C-S-H. 9. Increasing Al-concentrations lead to a retardation of the hydration of C3S. It is unclear if the uptake of aluminum in C-S-H to form C-(A)-S-H which has a significantly lower growth rate than pure C-S-H or a retarding effect of Al on the dissolution of C3S causes this phenomenon. 10. The surface of limestone provides excellent conditions for the nucleation and growth of C-S-H such that significantly more C-S-H nuclei are formed in presence of limestone compared to other SCM. 11. The reactivity of blast-furnace slag and fly ash depends on the particle size as well as on the intrinsic reactivity of especially the amorphous phases. 12. An increase in network modifying oxides (e.g. CaO) in the chemical composition of amorphous (calcium)aluminosilicates leads to an increasingly depolymerized network which in turn causes increasing reactivity. The role of amphoteric oxides (Al2O3, Fe2O3) that can be present as network modifying oxides as well as network forming oxides is not completely solved. 13. CO2-containing AFm-phases are thermodynamically more stable than monosulfoaluminate. This indirectly stabilizes the voluminous ettringite which causes a higher total volume of hydrates and lower porosity whereby higher compressive strength is reached. 14. Only a few percent of limestone in blended cement reacts chemically dependent on the Al2O3 available for reaction. Al2O3 that is provided by the reaction of Portland cement but also by the dissolution of SCM, especially by fly ash, reacts to form hemicarboaluminate which is transformed to monocarboaluminate as the hydration proceeds. Methodology 15. The influence of SCM on the early hydration of Portland cement in binary (including blast-furnace slag or fly ash or limestone or quartz) and ternary (including fly ash and limestone) systems was investigated applying isothermal calorimetry and analysis of the pore solution chemistry. Calculated saturation indices and solubility products of relevant phases were correlated with heat development. Based on the gained data it was reviewed if mechanisms that control the hydration of pure phases in diluted systems are also prevailing in cement pastes under realistic conditions. 16. The influence of the chemical composition of synthetic glasses on their dissolution at high pH was investigated in highly diluted systems using ion chromatography. Pozzolanity tests were conducted on pastes using simplified model systems and glass-blended Portland cements. The process of the glass dissolution was investigated by isothermal calorimetry and by thermogravimetry. Correlation of experimentally determined total bound water with bound water determined by mass balance calculations as a function of amount of glass reacted allowed to estimate the degree of glass reaction in the pastes. Further on selective dissolution experiments were carried out to crosscheck the results of the bound water/mass balance approach. 17. The reaction kinetics of quaternary pastes containing blast-furnace slag and fly ash simultaneously in the presence of limestone were investigated up to 28 d using isothermal calorimetry and chemical shrinkage measurements. In addition strength tests on mortar bars were carried out. 18. Pastes of quaternary blends were also investigated in terms of hydrate assemblage at ages of up to 182 d. Thermodynamic calculations regarding total volume of hydrates as a function of limestone and fly ash/blast-furnace slag content were conducted. The calculations were supported by thermogravimetric determination of bound water and portlandite content as well as qualitative X-ray diffraction. The results were correlated with strength tests on mortar bars. 19. The pore solutions of hydrated quaternary blends were extracted and investigated by means of ion chromatography at ages of up to 728 d. Based on the ion concentrations in the solutions saturation indices were calculated for relevant phases. In order to gain better insight to the blast-furnace slag reaction sulphate speciation was carried out at two blast furnace slag levels (20 and 30 wt.%) for selected samples up to 91 d of hydration and at 91 d for the whole matrix under investigation. Main results 20. Investigations on the early hydration kinetics of binary systems showed a higher heat flow in presence of SCM compared to neat Portland cement. This is caused by the higher surface area that is available for the nucleation of hydrates and by the lower (over)saturation with respect to C-S-H. An increase in the Ca-concentration in the pore solution did not cause lower dissolution rates of C3S as was reported for pure phases in diluted systems. The highest dissolution was observed in the presence of limestone, i.e. at the highest Ca-concentration. The general trend of the reaction rate is inversely related to the degree of undersaturation with respect to C3S. The more undersaturated the faster the observed reaction. The presence of increasing Al-concentrations caused a retardation of the reaction which is in line with investigations on pure phases in diluted systems. Higher sulphate concentrations could be detected for the fly ash containing blend which possibly hindered ettringite precipitation and results in higher Al-concentrations. Correspondingly the low sulphate concentrations lead to lower Al-concentrations in the presence of quartz, blast-furnace slag and limestone compared to fly ash. 21. The early hydration kinetics of quaternary systems is significantly accelerated in the presence of limestone while fly ash leads to retardation. Compared to reference systems containing inert quartz, investigations by means of isothermal calorimetry and chemical shrinkage revealed an acceleration caused by blast-furnace slag. Additions of fly ash, limestone or mixtures thereof introduced another acceleration but differences are too small to be significant and clear distinguishing between the various SCM is not possible. 22. Investigations on the reactivity of synthetic glasses showed that increasing amounts of network modifying oxides caused an increase in reactivity and dissolution rates. The results reveal that Al2O3 acts mainly as network modifying oxide in all investigated glasses. Experimentally determined bound water (thermogravimetric experiments) in model systems and blended cements can be compared with bound water determined by mass balance calculations carried out as a function of the amount of glass reacted. This enables to estimate the degree of glass reaction. 23. The actual content of blast-furnace slag, fly ash or limestone does not exert significant influence on the development of compressive strength up to 7 d. At later ages thermodynamic calculations predict a degree of CaCO3 reaction of 2 to 5 wt.%. This leads to the formation of hemicarbonate and monocarbonate whereby ettringite is indirectly stabilized. As a result the total amount of solids is increased and compressive strength shows a slight maximum. Hereby the degree of CaCO3 reaction depends on the Al2O3 available for reaction which is not only provided by the dissolution of Portland cement but especially by the dissolution of the fly ash. 24. In general the presence of blast-furnace slag and fly ash in the presence of limestone exerts little influence on the hydrate assemblage. The substitution of some of the blast-furnace slag by fly ash leads to a slight decrease of portlandite and C-S-H and gives rise to the formation of more monocarbonate and hemicarbonate. Portlandite is consumed in a pozzolanic reaction with the fly ash whereby C-S-H is formed. However, the low reactivity of the fly ash causes a decrease in the amount of C-S-H formed. Thereby a lower total volume of hydrates is generated which is in line with slightly lower compressive strength in case of increasing fly ash content. The overall influence is small and all systems investigated reach strength class 42.5 N according to EN 196-1. 25. Corresponding to the investigations of the hydrate assemblage the pore solution chemistry of quaternary systems showed only small variations. Depending on the fly ash content the highest variations are observed for aluminium, i.e. increasing fly ash content leads to higher Al-concentrations. Another effect of increasing fly ash contents is an increasing undersaturation with respect to portlandite and a decreasing undersaturation with respect to strätlingite indicating the dissolution of portlandite. 26. The total concentration of sulfur in the pore solution is controlled by sulphate (SO42–) while the concentrations of sulphite (SO32–) and thiosulphate (S2O32–) were very low. Up to 2 d of hydration about 90 % of the total sulphur is present as SO42–. After 91 d this value is reduced to about 36 % while about 28 % are present as S2O32–. In general higher blast-furnace slag content leads to higher concentrations of sulphite and thiosulphate after 7 d. KW - quaternary cement KW - supplementary cementitious materials KW - hydration kinetics KW - Thermodynamic modeling KW - degree of reaction KW - Hydrauliche Bindemittel Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20160705-26221 ER - TY - THES A1 - Mai, Luu T1 - Structural Control Systems in High-speed Railway Bridges N2 - Structural vibration control of high-speed railway bridges using tuned mass dampers, semi-active tuned mass dampers, fluid viscous dampers and magnetorheological dampers to reduce resonant structural vibrations is studied. In this work, the addressed main issues include modeling of the dynamic interaction of the structures, optimization of the parameters of the dampers and comparison of their efficiency. A new approach to optimize multiple tuned mass damper systems on an uncertain model is proposed based on the H-infinity optimization criteria and the DK iteration procedure with norm-bounded uncertainties in frequency domain. The parameters of tuned mass dampers are optimized directly and simultaneously on different modes contributing significantly to the multi-resonant peaks to explore the different possible combinations of parameters. The effectiveness of the present method is also evaluated through comparison with a previous method. In the case of semi-active tuned mass dampers, an optimization algorithm is derived to control the magnetorheological damper in these semi-active damping systems. The use of the proposed algorithm can generate various combinations of control gains and state variables. This can lead to the improvement of the ability of MR dampers to track the desired control forces. An uncertain model to reduce detuning effects is also considered in this work. Next, for fluid viscous dampers, in order to tune the optimal parameters of fluid viscous dampers to the vicinity of the exact values, analytical formulae which can include structural damping are developed based on the perturbation method. The proposed formulae can also be considered as an improvement of the previous analytical formulae, especially for bridge beams with large structural damping. Finally, a new combination of magnetorheological dampers and a double-beam system to improve the performance of the primary structure vibration is proposed. An algorithm to control magnetorheological dampers in this system is developed by using standard linear matrix inequality techniques. Weight functions as a loop shaping procedure are also introduced in the feedback controllers to improve the tracking ability of magnetorheological damping forces. To this end, the effectiveness of magnetorheological dampers controlled by the proposed scheme, along with the effects of the uncertain and time-delay parameters on the models, are evaluated through numerical simulations. Additionally, a comparison of the dampers based on their performance is also considered in this work. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2014,3 KW - High-speed railway bridge KW - Control system KW - Passive damper KW - Semi-active damper KW - Railway bridges Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20141223-23391 SN - 1610-7381 ER - TY - JOUR A1 - Zhang, Yongzheng T1 - Nonlocal dynamic Kirchhoff plate formulation based on nonlocal operator method JF - Engineering with Computers N2 - In this study, we propose a nonlocal operator method (NOM) for the dynamic analysis of (thin) Kirchhoff plates. The nonlocal Hessian operator is derived based on a second-order Taylor series expansion. The NOM does not require any shape functions and associated derivatives as ’classical’ approaches such as FEM, drastically facilitating the implementation. Furthermore, NOM is higher order continuous, which is exploited for thin plate analysis that requires C1 continuity. The nonlocal dynamic governing formulation and operator energy functional for Kirchhoff plates are derived from a variational principle. The Verlet-velocity algorithm is used for the time discretization. After confirming the accuracy of the nonlocal Hessian operator, several numerical examples are simulated by the nonlocal dynamic Kirchhoff plate formulation. KW - Angewandte Mathematik KW - nonlocal operator method KW - nonlocal Hessian operator KW - operator energy functional KW - dual-support KW - variational principle Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220209-45849 UR - https://link.springer.com/article/10.1007/s00366-021-01587-1 VL - 2022 SP - 1 EP - 35 PB - Springer CY - London ER - TY - THES A1 - Zhang, Yongzheng T1 - A Nonlocal Operator Method for Quasi-static and Dynamic Fracture Modeling N2 - Material failure can be tackled by so-called nonlocal models, which introduce an intrinsic length scale into the formulation and, in the case of material failure, restore the well-posedness of the underlying boundary value problem or initial boundary value problem. Among nonlocal models, peridynamics (PD) has attracted a lot of attention as it allows the natural transition from continuum to discontinue and thus allows modeling of discrete cracks without the need to describe and track the crack topology, which has been a major obstacle in traditional discrete crack approaches. This is achieved by replacing the divergence of the Cauchy stress tensor through an integral over so-called bond forces, which account for the interaction of particles. A quasi-continuum approach is then used to calibrate the material parameters of the bond forces, i.e., equating the PD energy with the energy of a continuum. One major issue for the application of PD to general complex problems is that they are limited to fairly simple material behavior and pure mechanical problems based on explicit time integration. PD has been extended to other applications but losing simultaneously its simplicity and ease in modeling material failure. Furthermore, conventional PD suffers from instability and hourglass modes that require stabilization. It also requires the use of constant horizon sizes, which drastically reduces its computational efficiency. The latter issue was resolved by the so-called dual-horizon peridynamics (DH-PD) formulation and the introduction of the duality of horizons. Within the nonlocal operator method (NOM), the concept of nonlocality is further extended and can be considered a generalization of DH-PD. Combined with the energy functionals of various physical models, the nonlocal forms based on the dual-support concept can be derived. In addition, the variation of the energy functional allows implicit formulations of the nonlocal theory. While traditional integral equations are formulated in an integral domain, the dual-support approaches are based on dual integral domains. One prominent feature of NOM is its compatibility with variational and weighted residual methods. The NOM yields a direct numerical implementation based on the weighted residual method for many physical problems without the need for shape functions. Only the definition of the energy or boundary value problem is needed to drastically facilitate the implementation. The nonlocal operator plays an equivalent role to the derivatives of the shape functions in meshless methods and finite element methods (FEM). Based on the variational principle, the residual and the tangent stiffness matrix can be obtained with ease by a series of matrix multiplications. In addition, NOM can be used to derive many nonlocal models in strong form. The principal contributions of this dissertation are the implementation and application of NOM, and also the development of approaches for dealing with fractures within the NOM, mostly for dynamic fractures. The primary coverage and results of the dissertation are as follows: -The first/higher-order implicit NOM and explicit NOM, including a detailed description of the implementation, are presented. The NOM is based on so-called support, dual-support, nonlocal operators, and an operate energy functional ensuring stability. The nonlocal operator is a generalization of the conventional differential operators. Combining with the method of weighted residuals and variational principles, NOM establishes the residual and tangent stiffness matrix of operate energy functional through some simple matrix without the need of shape functions as in other classical computational methods such as FEM. NOM only requires the definition of the energy drastically simplifying its implementation. For the sake of conciseness, the implementation in this chapter is focused on linear elastic solids only, though the NOM can handle more complex nonlinear problems. An explicit nonlocal operator method for the dynamic analysis of elasticity solid problems is also presented. The explicit NOM avoids the calculation of the tangent stiffness matrix as in the implicit NOM model. The explicit scheme comprises the Verlet-velocity algorithm. The NOM can be very flexible and efficient for solving partial differential equations (PDEs). It's also quite easy for readers to use the NOM and extend it to solve other complicated physical phenomena described by one or a set of PDEs. Several numerical examples are presented to show the capabilities of this method. -A nonlocal operator method for the dynamic analysis of (thin) Kirchhoff plates is proposed. The nonlocal Hessian operator is derived from a second-order Taylor series expansion. NOM is higher-order continuous, which is exploited for thin plate analysis that requires $C^1$ continuity. The nonlocal dynamic governing formulation and operator energy functional for Kirchhoff plates are derived from a variational principle. The Verlet-velocity algorithm is used for time discretization. After confirming the accuracy of the nonlocal Hessian operator, several numerical examples are simulated by the nonlocal dynamic Kirchhoff plate formulation. -A nonlocal fracture modeling is developed and applied to the simulation of quasi-static and dynamic fractures using the NOM. The phase field's nonlocal weak and associated strong forms are derived from a variational principle. The NOM requires only the definition of energy. We present both a nonlocal implicit phase field model and a nonlocal explicit phase field model for fracture; the first approach is better suited for quasi-static fracture problems, while the key application of the latter one is dynamic fracture. To demonstrate the performance of the underlying approach, several benchmark examples for quasi-static and dynamic fracture are solved. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,9 KW - Variationsprinzip KW - Partial Differential Equations KW - Taylor Series Expansion KW - Peridynamics KW - Variational principle KW - Phase field method KW - Peridynamik KW - Phasenfeldmodell KW - Partielle Differentialgleichung KW - Nichtlokale Operatormethode Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20221026-47321 ER - TY - JOUR A1 - Rabczuk, Timon A1 - Guo, Hongwei A1 - Zhuang, Xiaoying A1 - Chen, Pengwan A1 - Alajlan, Naif T1 - Stochastic deep collocation method based on neural architecture search and transfer learning for heterogeneous porous media JF - Engineering with Computers N2 - We present a stochastic deep collocation method (DCM) based on neural architecture search (NAS) and transfer learning for heterogeneous porous media. We first carry out a sensitivity analysis to determine the key hyper-parameters of the network to reduce the search space and subsequently employ hyper-parameter optimization to finally obtain the parameter values. The presented NAS based DCM also saves the weights and biases of the most favorable architectures, which is then used in the fine-tuning process. We also employ transfer learning techniques to drastically reduce the computational cost. The presented DCM is then applied to the stochastic analysis of heterogeneous porous material. Therefore, a three dimensional stochastic flow model is built providing a benchmark to the simulation of groundwater flow in highly heterogeneous aquifers. The performance of the presented NAS based DCM is verified in different dimensions using the method of manufactured solutions. We show that it significantly outperforms finite difference methods in both accuracy and computational cost. KW - Maschinelles Lernen KW - Neuronales Lernen KW - Fehlerabschätzung KW - deep learning KW - neural architecture search KW - randomized spectral representation Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220209-45835 UR - https://link.springer.com/article/10.1007/s00366-021-01586-2 VL - 2022 SP - 1 EP - 26 PB - Springer CY - London ER - TY - JOUR A1 - Kaps, Christian A1 - Schuch, Kai A1 - Stäblein, Stefan T1 - Silicate coatings for concrete components with waterglass systems by means of neutral salt initiation N2 - The objective of the investigations was the proof of the use of the neutral salt initiation as a construction material in the protecting silicate coating of concrete components, e.g. factory finished parts or reinforced concrete construction parts, by means of waterglass fused silica suspensions KW - Silicate KW - Coating KW - Wasserglas KW - Aggregation KW - Bindemittel KW - Waterglass KW - Alkalisilicate KW - Coating KW - Wasserglas KW - Sol-Gel Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20160601-25888 SP - 1 EP - 14 ER - TY - THES A1 - Abeltshauser, Rainer T1 - Identification and separation of physical effects of coupled systems by using defined model abstractions N2 - The thesis investigates at the computer aided simulation process for operational vibration analysis of complex coupled systems. As part of the internal methods project “Absolute Values” of the BMW Group, the thesis deals with the analysis of the structural dynamic interactions and excitation interactions. The overarching aim of the methods project is to predict the operational vibrations of engines. Simulations are usually used to analyze technical aspects (e. g. operational vibrations, strength, ...) of single components in the industrial development. The boundary conditions of submodels are mostly based on experiences. So the interactions with neighboring components and systems are neglected. To get physically more realistic results but still efficient simulations, this work wants to support the engineer during the preprocessing phase by useful criteria. At first suitable abstraction levels based on the existing literature are defined to identify structural dynamic interactions and excitation interactions of coupled systems. So it is possible to separate different effects of the coupled subsystems. On this basis, criteria are derived to assess the influence of interactions between the considered systems. These criteria can be used during the preprocessing phase and help the engineer to build up efficient models with respect to the interactions with neighboring systems. The method was developed by using several models with different complexity levels. Furthermore, the method is proved for the application in the industrial environment by using the example of a current combustion engine. T2 - Identifikation und Separation physikalischer Effekte von gekoppelten Systemen mittels definierter Modellabstraktionen T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2017,1 KW - Strukturdynamik KW - Wechselwirkung KW - Schwingung KW - Berechnung KW - Numerische Berechnung KW - Modellbildung KW - Schwingungsanalyse KW - Simulationsprozess Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-28600 ER - TY - JOUR A1 - Lahmer, Tom T1 - FEM-Based determination of real and complex elastic, dielectric, and piezoelectric moduli in piezoceramic materials JF - IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control N2 - We propose an enhanced iterative scheme for the precise reconstruction of piezoelectric material parameters from electric impedance and mechanical displacement measurements. It is based on finite-element simulations of the full three-dimensional piezoelectric equations, combined with an inexact Newton or nonlinear Landweber iterative inversion scheme. We apply our method to two piezoelectric materials and test its performance. For the first material, the manufacturer provides a full data set; for the second one, no material data set is available. For both cases, our inverse scheme, using electric impedance measurements as input data, performs well. KW - Finite-Elemente-Methode KW - Piezoelectric materials KW - Dielectric materials KW - Computational modeling KW - Frequency KW - Finite element methods KW - Manufacturing KW - Impedance measurement KW - Partial differential equations KW - Resonance KW - Resonanz Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171030-36083 ER - TY - THES A1 - Schrader, Kai T1 - Hybrid 3D simulation methods for the damage analysis of multiphase composites T1 - Hybride 3D Simulationsmethoden zur Abbildung der Schädigungsvorgänge in Mehrphasen-Verbundwerkstoffen N2 - Modern digital material approaches for the visualization and simulation of heterogeneous materials allow to investigate the behavior of complex multiphase materials with their physical nonlinear material response at various scales. However, these computational techniques require extensive hardware resources with respect to computing power and main memory to solve numerically large-scale discretized models in 3D. Due to a very high number of degrees of freedom, which may rapidly be increased to the two-digit million range, the limited hardware ressources are to be utilized in a most efficient way to enable an execution of the numerical algorithms in minimal computation time. Hence, in the field of computational mechanics, various methods and algorithms can lead to an optimized runtime behavior of nonlinear simulation models, where several approaches are proposed and investigated in this thesis. Today, the numerical simulation of damage effects in heterogeneous materials is performed by the adaption of multiscale methods. A consistent modeling in the three-dimensional space with an appropriate discretization resolution on each scale (based on a hierarchical or concurrent multiscale model), however, still contains computational challenges in respect to the convergence behavior, the scale transition or the solver performance of the weak coupled problems. The computational efficiency and the distribution among available hardware resources (often based on a parallel hardware architecture) can significantly be improved. In the past years, high-performance computing (HPC) and graphics processing unit (GPU) based computation techniques were established for the investigationof scientific objectives. Their application results in the modification of existing and the development of new computational methods for the numerical implementation, which enables to take advantage of massively clustered computer hardware resources. In the field of numerical simulation in material science, e.g. within the investigation of damage effects in multiphase composites, the suitability of such models is often restricted by the number of degrees of freedom (d.o.f.s) in the three-dimensional spatial discretization. This proves to be difficult for the type of implementation method used for the nonlinear simulation procedure and, simultaneously has a great influence on memory demand and computational time. In this thesis, a hybrid discretization technique has been developed for the three-dimensional discretization of a three-phase material, which is respecting the numerical efficiency of nonlinear (damage) simulations of these materials. The increase of the computational efficiency is enabled by the improved scalability of the numerical algorithms. Consequently, substructuring methods for partitioning the hybrid mesh were implemented, tested and adapted to the HPC computing framework using several hundred CPU (central processing units) nodes for building the finite element assembly. A memory-efficient iterative and parallelized equation solver combined with a special preconditioning technique for solving the underlying equation system was modified and adapted to enable combined CPU and GPU based computations. Hence, it is recommended by the author to apply the substructuring method for hybrid meshes, which respects different material phases and their mechanical behavior and which enables to split the structure in elastic and inelastic parts. However, the consideration of the nonlinear material behavior, specified for the corresponding phase, is limited to the inelastic domains only, and by that causes a decreased computing time for the nonlinear procedure. Due to the high numerical effort for such simulations, an alternative approach for the nonlinear finite element analysis, based on the sequential linear analysis, was implemented in respect to scalable HPC. The incremental-iterative procedure in finite element analysis (FEA) during the nonlinear step was then replaced by a sequence of linear FE analysis when damage in critical regions occured, known in literature as saw-tooth approach. As a result, qualitative (smeared) crack initiation in 3D multiphase specimens has efficiently been simulated. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2013,2 KW - high-performance computing KW - finite element method KW - heterogeneous material KW - domain decomposition KW - scalable smeared crack analysis KW - FEM KW - multiphase KW - damage KW - HPC KW - solver Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20131021-20595 ER - TY - THES A1 - Nouri, Hamidreza T1 - Mechanical Behavior of two dimensional sheets and polymer compounds based on molecular dynamics and continuum mechanics approach N2 - Compactly, this thesis encompasses two major parts to examine mechanical responses of polymer compounds and two dimensional materials: 1- Molecular dynamics approach is investigated to study transverse impact behavior of polymers, polymer compounds and two dimensional materials. 2- Large deflection of circular and rectangular membranes is examined by employing continuum mechanics approach. Two dimensional materials (2D), including, Graphene and molybdenum disulfide (MoS2), exhibited new and promising physical and chemical properties, opening new opportunities to be utilized alone or to enhance the performance of conventional materials. These 2D materials have attracted tremendous attention owing to their outstanding physical properties, especially concerning transverse impact loading. Polymers, with the backbone of carbon (organic polymers) or do not include carbon atoms in the backbone (inorganic polymers) like polydimethylsiloxane (PDMS), have extraordinary characteristics particularly their flexibility leads to various easy ways of forming and casting. These simple shape processing label polymers as an excellent material often used as a matrix in composites (polymer compounds). In this PhD work, Classical Molecular Dynamics (MD) is implemented to calculate transverse impact loading of 2D materials as well as polymer compounds reinforced with graphene sheets. In particular, MD was adopted to investigate perforation of the target and impact resistance force . By employing MD approach, the minimum velocity of the projectile that could create perforation and passes through the target is obtained. The largest investigation was focused on how graphene could enhance the impact properties of the compound. Also the purpose of this work was to discover the effect of the atomic arrangement of 2D materials on the impact problem. To this aim, the impact properties of two different 2D materials, graphene and MoS2, are studied. The simulation of chemical functionalization was carried out systematically, either with covalently bonded molecules or with non-bonded ones, focusing the following efforts on the covalently bounded species, revealed as the most efficient linkers. To study transverse impact behavior by using classical MD approach , Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) software, that is well-known among most researchers, is employed. The simulation is done through predefined commands in LAMMPS. Generally these commands (atom style, pair style, angle style, dihedral style, improper style, kspace style, read data, fix, run, compute and so on) are used to simulate and run the model for the desired outputs. Depends on the particles and model types, suitable inter-atomic potentials (force fields) are considered. The ensembles, constraints and boundary conditions are applied depends upon the problem definition. To do so, atomic creation is needed. Python codes are developed to generate particles which explain atomic arrangement of each model. Each atomic arrangement introduced separately to LAMMPS for simulation. After applying constraints and boundary conditions, LAMMPS also include integrators like velocity-Verlet integrator or Brownian dynamics or other types of integrator to run the simulation and finally the outputs are emerged. The outputs are inspected carefully to appreciate the natural behavior of the problem. Appreciation of natural properties of the materials assist us to design new applicable materials. In investigation on the large deflection of circular and rectangular membranes, which is related to the second part of this thesis, continuum mechanics approach is implemented. Nonlinear Föppl membrane theory, which carefully release nonlinear governing equations of motion, is considered to establish the non-linear partial differential equilibrium equations of the membranes under distributed and centric point loads. The Galerkin and energy methods are utilized to solve non-linear partial differential equilibrium equations of circular and rectangular plates respectively. Maximum deflection as well as stress through the film region, which are kinds of issue in many industrial applications, are obtained. T2 - Mechanisches Verhalten von zweidimensionalen Schichten und Polymerverbindungen basierend auf molekulardynamischer und kontinuumsmechanischem Ansatz KW - Molekulardynamik KW - Polymerverbindung KW - Auswirkung KW - Molecular Dynamics Simulation KW - Continuum Mechnics KW - Polymer compound KW - Impact Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220713-46700 ER - TY - THES A1 - Jenabidehkordi, Ali T1 - An Efficient Adaptive PD Formulation for Complex Microstructures N2 - The computational costs of newly developed numerical simulation play a critical role in their acceptance within both academic use and industrial employment. Normally, the refinement of a method in the area of interest reduces the computational cost. This is unfortunately not true for most nonlocal simulation, since refinement typically increases the size of the material point neighborhood. Reducing the discretization size while keep- ing the neighborhood size will often require extra consideration. Peridy- namic (PD) is a newly developed numerical method with nonlocal nature. Its straightforward integral form equation of motion allows simulating dy- namic problems without any extra consideration required. The formation of crack and its propagation is known as natural to peridynamic. This means that discontinuity is a result of the simulation and does not demand any post-processing. As with other nonlocal methods, PD is considered an expensive method. The refinement of the nodal spacing while keeping the neighborhood size (i.e., horizon radius) constant, emerges to several nonphysical phenomena. This research aims to reduce the peridynamic computational and imple- mentation costs. A novel refinement approach is introduced. The pro- posed approach takes advantage of the PD flexibility in choosing the shape of the horizon by introducing multiple domains (with no intersections) to the nodes of the refinement zone. It will be shown that no ghost forces will be created when changing the horizon sizes in both subdomains. The approach is applied to both bond-based and state-based peridynamic and verified for a simple wave propagation refinement problem illustrating the efficiency of the method. Further development of the method for higher dimensions proves to have a direct relationship with the mesh sensitivity of the PD. A method for solving the mesh sensitivity of the PD is intro- duced. The application of the method will be examined by solving a crack propagation problem similar to those reported in the literature. New software architecture is proposed considering both academic and in- dustrial use. The available simulation tools for employing PD will be collected, and their advantages and drawbacks will be addressed. The challenges of implementing any node base nonlocal methods while max- imizing the software flexibility to further development and modification will be discussed and addressed. A software named Relation-Based Sim- ulator (RBS) is developed for examining the proposed architecture. The exceptional capabilities of RBS will be explored by simulating three dis- tinguished models. RBS is available publicly and open to further develop- ment. The industrial acceptance of the RBS will be tested by targeting its performance on one Mac and two Linux distributions. KW - Peridynamik KW - Numerical Simulations KW - Peridynamics KW - Numerical Simulations Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20221124-47422 ER - TY - THES A1 - Vogler, Verena T1 - A framework for artificial coral reef design: Integrating computational modelling and high precision monitoring strategies for artificial coral reefs – an Ecosystem-aware design approach in times of climate change N2 - Tropical coral reefs, one of the world’s oldest ecosystems which support some of the highest levels of biodiversity on the planet, are currently facing an unprecedented ecological crisis during this massive human-activity-induced period of extinction. Hence, tropical reefs symbolically stand for the destructive effects of human activities on nature [4], [5]. Artificial reefs are excellent examples of how architectural design can be combined with ecosystem regeneration [6], [7], [8]. However, to work at the interface between the artificial and the complex and temporal nature of natural systems presents a challenge, i.a. in respect to the B-rep modelling legacy of computational modelling. The presented doctorate investigates strategies on how to apply digital practice to realise what is an essential bulwark to retain reefs in impossibly challenging times. Beyond the main question of integrating computational modelling and high precision monitoring strategies in artificial coral reef design, this doctorate explores techniques, methods, and linking frameworks to support future research and practice in ecology led design contexts. Considering the many existing approaches for artificial coral reefs design, one finds they often fall short in precisely understanding the relationships between architectural and ecological aspects (e.g. how a surface design and material composition can foster coral larvae settlement, or structural three-dimensionality enhance biodiversity) and lack an integrated underwater (UW) monitoring process. Such a process is necessary in order to gather knowledge about the ecosystem and make it available for design, and to learn whether artificial structures contribute to reef regeneration or rather harm the coral reef ecosystem. For the research, empirical experimental methods were applied: Algorithmic coral reef design, high precision UW monitoring, computational modelling and simulation, and validated through parallel real-world physical experimentation – two Artificial Reef Prototypes (ARPs) in Gili Trawangan, Indonesia (2012–today). Multiple discrete methods and sub techniques were developed in seventeen computational experiments and applied in a way in which many are cross valid and integrated in an overall framework that is offered as a significant contribution to the field. Other main contributions include the Ecosystem-aware design approach, Key Performance Indicators (KPIs) for coral reef design, algorithmic design and fabrication of Biorock cathodes, new high precision UW monitoring strategies, long-term real-world constructed experiments, new digital analysis methods and two new front-end web-based tools for reef design and monitoring reefs. The methodological framework is a finding of the research that has many technical components that were tested and combined in this way for the very first time. In summary, the thesis responds to the urgency and relevance in preserving marine species in tropical reefs during this massive extinction period by offering a differentiated approach towards artificial coral reefs – demonstrating the feasibility of digitally designing such ‘living architecture’ according to multiple context and performance parameters. It also provides an in-depth critical discussion of computational design and architecture in the context of ecosystem regeneration and Planetary Thinking. In that respect, the thesis functions as both theoretical and practical background for computational design, ecology and marine conservation – not only to foster the design of artificial coral reefs technically but also to provide essential criteria and techniques for conceiving them. Keywords: Artificial coral reefs, computational modelling, high precision underwater monitoring, ecology in design. N2 - Charakteristisch für das Zeitalter des Klimawandels sind die durch den Menschen verursachte Meeresverschmutzung sowie ein massiver Rückgang der Artenvielfalt in den Weltmeeren. Tropische Korallenriffe sind als eines der ältesten und artenreichsten Ökosysteme der Erde besonders stark gefährdet und stehen somit symbolisch für die zerstörerischen Auswirkungen menschlicher Aktivitäten auf die Natur [4], [5]. Um dem massiven Rückgang der Korallenriffe entgegenzuwirken, wurden von Menschen künstliche Riffsysteme entwickelt [6], [7]. Sie sind Beispiele dafür, wie Architektur und die Regenerierung von Ökosystemen miteinander verbunden werden können [8]. Eine Verknüpfung von einerseits künstlichen und andererseits komplexen, sich verändernden natürlichen Systemen, stellt jedoch eine Herausforderung dar, u.a. in Bezug auf die Computermodellierung (B-Rep Modellierung). Zum Erhalt der Korallenriffe werden in der vorliegende Doktorarbeit Strategien aus der digitalen Praxis neuartig auf das Entwerfen von künstlichen Korallenriffen angewendet. Die Hauptfrage befasst sich damit, wie der Entwurfsprozess von künstlichen Korallenriffen unter Einbeziehung von Computermodellierung und hochpräzisen Überwachungsstrategien optimiert werden kann. In diesem Zusammenhang werden Techniken, Methoden sowie ein übergeordnetes Framework erforscht, welche zukünftige Forschung und Praxis in Bezug auf Ökologie-geleitete Entwurfsprozesse fördern soll. In Anbetracht der vielen vorhandenen künstlichen Riffsysteme, kann man feststellen, dass die Zusammenhänge zwischen Architektur- und Ökosystem-Anforderungen nicht genau untersucht und dadurch bei der Umsetzung nicht entsprechend berücksichtigt werden. Zum Beispiel wie Oberflächenbeschaffenheit und Materialität eine Ansiedlung von Korallenlarven begünstigt oder wie eine räumlich vielseitige Struktur die Artenvielfalt verbessern kann. Zudem fehlt ein integrierter Unterwasser-Überwachungsprozess, welcher Informationen über das Ökosystem liefert und diese dem Entwurf bereitstellt. Zusätzlich ist eine Unterwasser-Überwachung notwendig, um herauszufinden, ob die künstlichen Riffstrukturen zur Regenerierung beitragen oder dem Ökosystem gänzlich schaden. In dieser Forschungsarbeit werden empirische und experimentelle Methoden angewendet: Algorithmisches Entwerfen für Korallenriffe, hochpräzise Unterwasser-Überwachung, Computermodellierung und -simulation. Die Forschung wird seit 2012 bis heute durch zwei Riffprototypen (Artificial Reef Prototypes – ARPs) in Gili Trawangan, Indonesien validiert. Zusätzlich wurden weitere separate Methoden und Techniken in insgesamt siebzehn computergestützten Experimenten entwickelt und so angewendet, dass viele kreuzvalidiert und in ein Framework integriert sind, welches dann als bedeutender Beitrag dem Forschungsgebiet zur Verfügung steht. Weitere Hauptbeiträge sind der Ökosystem-bewusste Entwurfsansatz (Ecosystem-aware design approach), Key Performance Indicators (KPIs) für das Gestalten von Korallenriffen, algorithmisches Entwerfen und die Herstellung von Biorock-Kathoden, neue hochpräzise Unterwasser-Überwachungsstrategien, reale Langzeitexperimente, neue digitale Analysemethoden, sowie zwei webbasierte Softwareanwendungen für die Gestaltung und die Überwachung von künstlichen Korallenriffen. Das methodische Framework ist das Hauptergebnis der Forschung, da die vielen technischen Komponenten in dieser Weise zum ersten Mal getestet und kombiniert wurden. Zusammenfassend reagiert die vorliegende Doktorarbeit sowohl auf die Dringlichkeit als auch auf die Relevanz der Erhaltung von Artenvielfalt in tropischen Korallenriffen in Zeiten eines massiven Aussterbens, indem sie einen differenzierten Entwurfsansatz für künstliche Korallenriffe offeriert. Die Arbeit zeigt auf, dass ein digitales Entwerfen einer solchen „lebendigen Architektur“ unter Berücksichtigung vielfältiger Anforderungen und Leistungsparametern machbar ist. Zusätzlich bietet sie eine ausführliche kritische Diskussion über die Rolle von computergestützten Entwerfen und Architektur im Zusammenhang mit Regenerierung von Ökosystemen und “Planetary Thinking”. In dieser Hinsicht fungiert die Doktorarbeit als theoretischer und praktischer Hintergrund für computergestütztes Entwerfen, Ökologie und Meeresschutz. Eine Verbesserung des Entwerfens von künstlichen Korallenriffen wird nicht nur auf technischer Ebene aufgezeigt, sondern es werden auch die wesentlichen Kriterien und Techniken für deren Umsetzung benannt. Schlüsselwörter: Künstliche Korallenriffe, Computermodellierung, hochpräzise Unterwasser-Überwachung, Ökologie im Architekturentwurf. KW - Korallenriff KW - Algorithmus KW - Architektur KW - Meeresökologie KW - Software KW - Artificial coral reefs KW - Computational modelling KW - High precision underwater monitoring KW - Ecology in design KW - Künstliche Korallenriffe KW - Unterwasserarchitektur Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220322-46115 UR - https://artificialreefdesign.com/ SN - 978-3-00-074495-2 N1 - Die URL führt zu 3D Modelle von echten Korallenriffen. ER - TY - THES A1 - Stäudel, Jürgen T1 - Development, Implementation and Operation of Integrated Sanitation Systems Based on Material-Flows – Integrated Sanitation in the City of Darkhan, Mongolia - A Practicable Example N2 - The world society faces a huge challenge to implement the human right of “access to sanitation”. More and more it is accepted that the conventional approach towards providing sanitation services is not suitable to solve this problem. This dissertation examines the possibility to enhance “access to sanitation” for people who are living in areas with underdeveloped water and wastewater infrastructure systems. The idea hereby is to follow an integrated approach for sanitation, which allows for a mutual completion of existing infrastructure with resource-based sanitation systems. The notion “integrated sanitation system (iSaS)” is defined in this work and guiding principles for iSaS are formulated. Further on the implementation of iSaS is assessed at the example of a case study in the city of Darkhan in Mongolia. More than half of Mongolia’s population live in settlements where yurts (tents of Nomadic people) are predominant. In these settlements (or “ger areas”) sanitation systems are not existent and the hygienic situation is precarious. An iSaS has been developed for the ger areas in Darkhan and tested over more than two years. Further on a software-based model has been developed with the goal to describe and assess different variations of the iSaS. The results of the assessment of material-flows, monetary-flows and communication-flows within the iSaS are presented in this dissertation. The iSaS model is adaptable and transferable to the socio-economic conditions in other regions and climate zones. N2 - Die Weltgesellschaft steht der großen Herausforderung gegenüber das Menschrecht auf Zugang zu Sanitärversorgung umzusetzen. Es wird zunehmend akzeptiert, dass konventionelle Ansätze der Abwasserwirtschaft dieses Problem nicht lösen können. Die vorliegende Dissertation untersucht die Möglichkeit eines integrierten Ansatzes, welcher Stoffflüsse, Geldflüsse und Kommunikationsflüsse gemeinsam betrachtet und komplementär zu existierenden Infrastruktursystemen angewendet werden kann. Der Begriff „integriertes Sanitärsystem (iSaS)“ wird definiert und anhand eines Fallbeispiels in der Stadt Darkhan in der Mongolei untersucht. Hierbei wurde ein Sanitärsystem für Jurtensiedlungen erarbeitet, pilothaft umgesetzt und über 2 Jahre betrieben. Weiterhin wurde ein software- basiertes Modell anhand der Prinzipien von iSaS entwickelt und verschiedene Variationen des Systems untersucht und diskutiert. Das Modell kann an die klimatischen und sozioökonomischen Rahmenbedingungen in anderen Regionen der Welt angepasst werden und damit die potentielle Umsetzung von iSaS unterstützen. KW - Abwasser KW - Infrastruktur KW - Entwicklungsländer KW - Abfall KW - iPiT® KW - Mongolia KW - integrated sanitation system KW - new alternative sanitation systems NASS KW - UDDT Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170512-31794 ER -