TY - CHAP A1 - Ducke, M. A1 - Eckstein, U. A1 - Montag, U. T1 - Die Eisenbahnbrücken des Lehrter Bahnhofs in Berlin - Ein ganzheitliches FE-Berechnungskonzept N2 - Der Komplexität moderner Brückenbauwerke scheinen die verwendeten Berechungsmodelle oft nicht angemessen. Tragwerksberechnungen basieren in vielen Fällen noch auf der Vorgehensweise, das Brückenbauwerk in Einzelbauteile zu zerlegen und mit unterschiedlichen Teilmodellen zu behandeln. Das erscheint, auch vor dem Hintergrund ständig wachsender Rechnerleistung, nicht mehr zeitgemäß. Dies gilt zum Beispiel auch für die gängige Praxis, flächenhafte Brückenüberbauten mit Balkenmodellen zu berechnen. Der vorliegende Beitrag stellt ein ganzheitliches Berech-nungskonzept vor, welches auf der Basis eines einzigen FE-Modells die Berechnung des Gesamtbauwerks erlaubt. Damit wird für alle Bauteile neben der Zustandsgrößenberechnung auch die Bemessung von Stahl- und Spannbetonbauteilen bis hin zu Nachweisen wie zur Beschränkung der Rissbreite geführt. Die Anwendung dieses Berechnungskonzeptes wird am Beispiel der Eisenbahnüberführung des neuen Lehrter Bahn-hofs in Berlin gezeigt. Das verwendete FE-Modell umfasst Baugrund, Fundamente, Stahl- bzw. Gußstahlunterkonstruktion sowie den Stahl- bzw. Spannbetonüberbau. Besonderheiten sind unter anderem die Modellierung des plattenbalkenartigen Überbaus durch exzentrische, vorspannbare Schalenelemente und das getrennte Vorhalten von tragwerks- und lastbezogenen Eingabefiles. Damit gelingt die sequentielle Erfassung unterschiedlicher Bettungsmoduli zur Simulation statischer und dynamischer Beanspruchungen, die Berücksichtigung des Anspannens und der Interaktion zwischen vorgespannten Stahlverbänden zur Aufnahme von Horizontallasten sowie die Berücksichtigung unterschiedlicher statischer Systeme bei der Herstellung des Spannbetonüberbaus. KW - Berlin KW - Eisenbahnbrücke KW - Berechnung KW - Finite-Elemente-Methode KW - Lehrter Bahnhof KW - Gesamtbauwerk Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5812 ER - TY - THES A1 - Kurukuri, Srihari T1 - Homogenization of Damaged Concrete Mesostructures using Representative Volume Elements - Implementation and Application to SLang N2 - This master thesis explores an important and under-researched topic on the so-called bridging of length scales (from >meso< to >macro<), with the concept of homogenization in which the careful characterization of mechanical response requires that the developed material model >bridge< the representations of events that occur at two different scales. The underlying objective here is to efficiently incorporate material length scales in the classical continuum plasticity/damage theories through the concept of homogenization theory. The present thesis is devoted to computational modeling of heterogeneous materials, primarily to matrix-inclusion type of materials. Considerations are focused predominantly on the elastic and damage behavior as a response to quasistatic mechanical loading. Mainly this thesis focuses to elaborate a sound numerical homogenization model which accounts for the prediction of overall properties with the application of different types of boundary conditions namely: periodic, homogeneous and mixed type of boundary conditions over two-dimensional periodic and non-periodic RVEs and three-dimensional non-periodic RVEs. Identification of the governing mechanisms and assessing their effect on the material behavior leads one step further. Bringing together this knowledge with service requirements allows for functional oriented materials design. First, this thesis gives attention on providing the theoretical basic mechanisms involved in homogenization techniques and a survey will be made on existing analytical methods available in literature. Second, the proposed frameworks are implemented in the well known finite element software programs ANSYS and SLang. Simple and efficient algorithms in FORTRAN are developed for automated microstructure generation using RSA algorithm in order to perform a systematic numerical testing of microstructures of composites. Algorithms are developed to generate constraint equations in periodic boundary conditions and different displacements applied spatially over the boundaries of the RVE in homogeneous boundary conditions. Finally, nonlinear simulations are performed at mesolevel, by considering continuum scalar damage behavior of matrix material with the linear elastic behavior of aggregates with the assumption of rigid bond between constituents. KW - Schadensmechanik KW - Finite-Elemente-Methode KW - Beton KW - Homogenisierung KW - Repräsentative Volumen Elemente KW - Mesoskala KW - Homogenization KW - Representative Volume Elements KW - Mesoscale Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6670 N1 - Der Volltext-Zugang wurde im Zusammenhang mit der Klärung urheberrechtlicher Fragen mit sofortiger Wirkung gesperrt. ER - TY - CHAP A1 - van Rooyen, G.C. A1 - Olivier, A. H. T1 - Notes on structural analysis in a distributed collaboratory N2 - The worldwide growth of communication networks and associated technologies provide the basic infrastructure for new ways of executing the engineering process. Collaboration amongst team members seperated in time and location is of particular importance. Two broad themes can be recognized in research pertaining to distributed collaboration. One theme focusses on the technical and technological aspects of distributed work, while the other emphasises human aspects thereof. The case of finite element structural analysis in a distributed collaboratory is examined in this paper. An approach is taken which has its roots in human aspects of the structural analysis task. Based on experience of how structural engineers currently approach and execute this task while utilising standard software designed for use on local workstations only, criteria are stated for a software architechture that could support collaborative structural analysis. Aspects of a pilot application and the results of qualitative performance measurements are discussed. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Finite-Elemente-Methode Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1451 ER - TY - CHAP A1 - Köppler, H. A1 - Roos, Dirk A1 - Burkhardt, Gerhard T1 - Zur Berechnung vielschichtiger Schalen mit orthotropen Schichten N2 - Wirklichkeitsnahe Erfassung und Beschreibung des Trag- und Verformungsverhaltens von Strukturen baulicher Anlagen hat in den letzten Jahrzehnten ständig an Bedeutung gewonnen. Konstruktionen im Hoch- und Industriebau werden zunehmend multifunktional genutzt - die >Grenzen< zwischen Bauwerk und Tragwerk, zwischen Hüll- und Tragkonstruktion lösen sich auf. Werden raumabschließende Elemente (Wände, Decken, Dächer) gleichzeitig als Tragelemente und wärme- und schalldämmende Konstruktionen ausgeführt, so entstehen beispielsweise Sandwichplatten, deren Schichten sehr stark differierende Materialeigenschaften aufweisen. Beim Aufbau des FEM-Modells für vielschichtige Schalen können die Formänderungshypothesen für jede Schicht einzeln als auch für die Schale insgesamt gegeben werden. Im ersten Fall ist der Knotenfreiheitsgrad von der Schichtenzahl abhängig, im zweiten Fall nicht. Im weiteren wird eine Formänderungshypothese für das Schichtenpaket angenommen. Ausgegangen wird von den Gleichungen der 3D-Elastizitätstheorie. Die Berücksichtigung der Querkraftschubverformungen ergibt die Möglichkeit einer adäquaten Beschreibung der Verformungen sowohl dünner Schalen als auch von Schalen mittlerer Dicke; die Berechnung der Krümmungen und der LAMEschen Parameter der Bezugsfläche zu umgehen, was für komplizierte Schalenformen eine selbständige Aufgabe ist; eines natürlichen Übergangs von homogenen zu geschichteten Schalen. Das vielschichtige isoparametrische Schalen-FE wird vorgestellt, seine Implementierung in das in Entwicklung befindliche Programmsystem SLANG wird vorbereitet. KW - Schale KW - Sandwichbauweise KW - Orthotropes Bauteil KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4379 ER - TY - CHAP A1 - Berger, Hans A1 - Graeff-Weinberg, K. T1 - FEM-Detailuntersuchungen an Tragwerken unter Einsatz von pNh-Übergangselementen N2 - Detailuntersuchungen an Tragwerken führen bei FE-Berechnungen immer wieder auf das Problem einer geeigneten Netzgestaltung. Während in weiten Bereichen ein grobes Netz ausreicht, muß an kritischen Stellen ein sehr feines Netz gewählt werden, um gerade dort hinreichend genaue Ergebnisse zu erhalten. Bei der Realisierung lokaler Netzverdichtungen stellt die Gestaltung des Übergangs vom groben zum feinen Netz das Hauptproblem dar. Im Beitrag wird hierzu eine Familie von FE-Übergangselementen vorgestellt, mit denen sich eine voll-kompatible Kopplung von wenigen großen Elementen mit vielen kleinen Elementen bereits über nur eine Stufe erzielen läßt. Diese neu entwickelten sogenannten pNh-Elemente ermöglichen an einer oder mehreren Seiten den Anschluß von N kleineren Elementen (Elementseiten für h-Verfeinerung). Das wird durch N stückweise definierte Ansatzfunktionen an den entsprechenden Seiten erreicht, wobei die Teilung nicht äquidistant sein braucht. Darüber hinaus ist es möglich, Elemente unterschiedlichen Polynomgrades p an den Standardseiten und den Verfeinerungsseiten anzuschließen. Der praktische Einsatz der Übergangselemente setzt geeignete automatische oder halbautomatische Netzgeneratoren voraus, die diese Elemente einbeziehen. Im Rahmen einer substrukturorientierten Modellierung läßt sich dies besonders günstig realisieren. Im Beitrag wird gezeigt, wie durch Zerlegung des Gesamtmodells in Bereiche mit grobem Netz, mit Übergangsnetz und mit feinem Netz, eine effektive Generierung der Netzverdichtungen zu erreichen ist. An einem praktischen Beispiel aus dem Bauingenieurwesen werden die Vorteile des vorgestellten Übergangselementkonzeptes umfassend demonstriert. KW - Tragwerk KW - Modellierung KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4267 ER - TY - JOUR A1 - Milbradt, Peter A1 - Schierbaum, Jochen A1 - Schwöppe, Axel T1 - Finite Cell-Elements of Higher Order N2 - The method of the finite elements is an adaptable numerical procedure for interpolation as well as for the numerical approximation of solutions of partial differential equations. The basis of these procedure is the formulation of suitable finite elements and element decompositions of the solution space. Classical finite elements are based on triangles or quadrangles in the two-dimensional space and tetrahedron or hexahedron in the threedimensional space. The use of arbitrary-dimensional convex and non-convex polyhedrons as the geometrical basis of finite elements increases the flexibility of generating finite element decompositions substantially and is sometimes the only way to get a clear decomposition... KW - Finite-Elemente-Methode KW - Physikalisches Verfahren Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2524 ER - TY - JOUR A1 - Kaklauskas, Gintaris A1 - Cervenka, Vladimir A1 - Cervenka, Jan T1 - Deflection Calculation of RC Beams: Finite Element Software versus Design Code Methods N2 - The paper investigates accuracy of deflection predictions made by the finite element package ATENA and design code methods ACI and EC2. Deflections have been calculated for a large number of experimental reinforced concrete beams reported by three investigators. Statistical parameters have been established for each of the technique at different load levels, separately for the beams with small and moderate reinforcement ratio. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Balken Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2498 ER - TY - CHAP A1 - Schutte, Gerrit T1 - Zur Ermittlung von Spannungen am Rand eines elastischen Kontinuums N2 - Für den Entwurf von Ingenieurbauten ist eine zuverlässige Prognose über den Spannungsverlauf im Bauwerk und auf dessen Rand von großer Bedeutung. Eine geschlossene Lösung der elastischen Bestimmungsgleichungen des Bauwerks ist in der Regel nicht verfügbar. Es wird daher unter Verwendung der Methode der gewichteten Reste eine schwache Form der Gleichungen abgeleitet, die zu einem gemischten Arbeitsprinzip führt. Das zugehörige Finite-Elemente-Modell erlaubt es Spannungen am Rand des Bauwerks zu ermitteln, die im Gleichgewicht zu den angreifenden Lasten stehen. KW - Kontinuum KW - Elastizitätstheorie KW - Randspannung KW - Finite-Elemente-Methode Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6135 ER - TY - JOUR A1 - Êirinhevsky, V. V. A1 - Dîkhnyak, B. M. A1 - Êirichevsky, R. V. A1 - Êîzub, Y. G. T1 - Determination of the Temperature of Dissipative Warming and Parameters of Fracture in Elastomers with using of Singular Finite Elements N2 - For modeling of singular fields of stresses and deformations in elasters with a crack is offered to use of three-dimesional a special finite element. Weak compessible of elasters is taken into account on the basis of threefold approximation of fields of displacements, deformations and function of volume change. At intensive cyclic loading of the elastomer constructions with a crack it is necessary to take into account warming and large deformations at the crack top. The stress-deformed state elasters with a crack is determined from the decision of a nonlinear problem by a modified method Newton-Kantorovich. Account stress intensity factors for a rectangular plate with a various arrangement of a through crack is executed. Process of development of a surface crack and dissipative warming in prismatic a element of shift is investigated. KW - Elastomer KW - Temperatur KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5471 ER - TY - CHAP A1 - Daniunas, A. A1 - Komka, A. A1 - Werner, F. T1 - ANALYSIS AND DETERMINATION OF STRENGTH IN PLASTIC STAGE OF FREE FORM STEEL SHAPES N2 - The steel structure design codes require to check up the member strength when evaluating plastic deformations. The model of perfectly plastic material is accepted. The strength criteria for simple cross-sections (I section, etc.) of steel members are given in design codes. The analytical strength criteria for steel cross-sections and numerical approaches based on stepwise procedure are investigated in many articles. Another way for checking the carrying capacity of cross-sections is the use of methods that are applied for defining strain-deformed state of elastic perfectly plastic systems. In this paper non-iterative methods are suggested for checking strength of cross-sections. Carrying capacity of cross section is verified according to extremum principle of plastic fail under monotonically loading and the strain-deformed state of cross-section is defined according to extremum energy principals of elastic potential of residual stresses and complementary work of residual displacements. The mathematical expressions of these principals for discrete cross-section are formulated as problems of convex mathematical programming. The cross-section of steel member using finite element method is divided into free form plane elements. The constant distribution of stresses along the finite element is accepted. The relationships of finite elements for static formulation of the problem are formed so, that kinematics formulation relationships could be obtained in a formal way using the theory of duality. Numerical examples of determination of cross-section strength, composition of interactive curves and composition of moment-curvature curves for different axial force levels are presented. KW - Stahlkonstruktion KW - Plastische Deformation KW - Mathematisches Modell KW - Finite-Elemente-Methode Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5803 ER - TY - CHAP A1 - Gurtovy, O. G. A1 - Piskunov, V. G. T1 - HIGH-PRECISION MODELING AND FINITE-ELEMENT INVESTIGATION OF ELASTOPLASTIC DEFORMATION OF NON-ISOTROPIC THICK SANDWICH PLATES AND SHELLS N2 - There was suggested a phenomenological modified quadratic condition of the beginning of plasticity for plastic and quasifragile orthotropic materials. Limiting surface in the shape of a paraboloid with an axis bend over hydrostatic axis corresponds to the condition. The equations of theory of current with the isotropic and anisotropic hardenings, associated with the suggested yield condition, modified into the version of determining equations of strain theory of plasticity are received. These defining equations formed the basis of highlyprecise non-classic continual (along thickness) theory of non-linear deformation of thick sandwich plates and sloping shells. In the approximations along the cross coordinate the specificity of flexural and non-flexural deformations is taken into account. The necessity of introducing the approximations of higher order, as well as accounting for the cross compression while decreasing of the relatively cross normal and shear layer rigidness is shown. The specifications, obtained in comparison with the known physically nonlinear specified model of the bending of plates with orthotropic layers are distinguished. An effective procedure of linearization of the solving equations and getting the solutions in frames of the discrete-continual scheme of the finite-element method is suggested. The approximations of higher order let to model the appearance of the cracs of layers being split by the introducing of slightly hard thin layers into the finite element, not violating the idea of continuality of theory. Calculation of a threelayer plate with rigid face diaphragms on the contour is considered KW - Platte KW - Schale KW - Sandwichbauteil KW - Elastoplastizität KW - Finite-Elemente-Methode Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5848 ER - TY - CHAP A1 - Kirichuk, A. A1 - Köppler, H. T1 - Numerical Algorithms and Computer Modeling for nonlinear Analysis of Shell Structures N2 - The dynamic behaviour of shells, which are widely used in construction and mechanical engineering as critical components of machinery and 3-D structures, under static and dynamic loadings is described by system of deep nonlinear differential equations. Solution of these equations can be received with assistance of technique basing on a modern numerical algorithms and computer modeling.. The system of nonlinear differential equations of vibration of the shells is proposed taking into account the inertia forces in the tangential and normal directions. Its solution is based on combination of parameter prolongation method, finite-difference method and the Newton-Kantorovich iterative algorithm that allows plotting the loading trajectories and determination of bifurcation points on them. Package of Applied Programs >SEVSOR< is a computation means to be used in research of deformation, stability and vibration in thin axically-symmetric shells of complicated shape Input data include information on shell geometry, physical and mechanical properties, bearing conditions, types of loadings and load application. Frame output of motion forms in real time or either in decelerated or accelerated time scales for creating cartoons or video films is used for analysis of the compound dynamic processes in shell-type structures. KW - Schale KW - Nichtlineares Phänomen KW - Modellierung KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4382 ER - TY - CHAP A1 - Popova, E. D. A1 - Datcheva, Maria A1 - Iankov, Roumen T1 - Mechanical Models with Interval Parameters N2 - In this paper we consider modelling of composite material with inclusions where the elastic material properties of both matrix and inclusions are uncertain and vary within prescribed bounds. Such mechanical systems, involving interval uncertainties and modelled by finite element method, can be described by parameter dependent systems of linear interval equations and process variables depending on the system solution. A newly developed hybrid interval approach for solving parametric interval linear systems is applied to the considered model and the results are compared to other interval methods. The hybrid approach provides very sharp bounds for the process variables - element strains and stresses. The sources for overestimation when dealing with interval computations are demonstrated. Based on the element strains and stresses, we introduce a definition for the values of nodal strains and stresses by using a set-theoretic approach. KW - Verbundwerkstoff KW - Modellierung KW - Finite-Elemente-Methode Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-3482 ER - TY - JOUR A1 - Ganev, T. A1 - Marinov, M. T1 - Towards Optimal Designing of thin elastic Plates with a specific free Oscillations Frequency N2 - Thin elastic plates are the basic constructional elements and are very often subjected to dynamic effects especially in the machine-building structures. Their saving design of resonance conditions of operation is an extremely complicated task which cannot be solved analytically. In the present report an efficient and sufficiently general method for optimal design of thin plates is worked out on the basis of energy resonance method of Wilder, the method of the finite elements for dynamic research and the methods of parameter optimization. By means of these methods various limitations and requirements put by the designer to the plates can be taken into account. A programme module for numerical investigation of the weight variation of the plate depending on the taken variable of the designed thickness at different supporting conditions is developed. The reasons for the considerable quantity and quality difference between the obtained optimal designs are also analysed. KW - Platte KW - Optimierung KW - Freie Schwingung KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5375 ER - TY - JOUR A1 - Pick, Tobias A1 - Heimsund, Bjoern-Ove A1 - Milbradt, Peter T1 - Development and Analysis of Sparse Matrix Concepts for Finite Element Approximation on general Cells N2 - In engineering and computing, the finite element approximation is one of the most well-known computational solution techniques. It is a great tool to find solutions for mechanic, fluid mechanic and ecological problems. Whoever works with the finite element method will need to solve a large system of linear equations. There are different ways to find a solution. One way is to use a matrix decomposition technique such as LU or QR. The other possibility is to use an iterative solution algorithm like Conjugate Gradients, Gauß-Seidel, Multigrid Methods, etc. This paper will focus on iterative solvers and the needed storage techniques... KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Bandmatrix Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2500 ER - TY - CHAP A1 - Baitsch, Matthias A1 - Hartmann, Dietrich T1 - Object Oriented Finite Element Analysis for Structural Optimization using p-Elements N2 - The optimization of continuous structures requires careful attention to discretization errors. Compared to ordinary low order formulation (h-elements) in conjunction with an adaptive mesh refinement in each optimization step, the use of high order finite elements (so called p-elements) has several advantages. However, compared to the h-method a higher order finite element analysis program poses higher demands from a software engineering point of view. In this article the basics of an object oriented higher order finite element system especially tailored to the use in structural optimization is presented. Besides the design of the system, aspects related to the employed implementation language Java are discussed. KW - Konzipieren KW - Bauwerk KW - Finite-Elemente-Methode Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1089 ER - TY - JOUR A1 - Galffy, Mozes A1 - Wellmann Jelic, Andres A1 - Hartmann, Dietrich T1 - Lifetime-oriented modelling of vortex-induced across-wind vibrations on bridge tie rods N2 - The influence of vortex-induces vibrations on vertical tie rods has been proved as a determinant load factor in the lifetime-oriented dimensioning of arched steel bridges. Particularly, the welded connection plates between the suspenders and the arches often exhibit cracks induced primarily rods. In this context, the synchronization of the vortex-shedding to the rod motion in a critical wind velocity range, the so-called lock-in effect, is of essential interest. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Brückenbau KW - Schwingung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2536 ER - TY - CHAP A1 - Montag, U. T1 - A New Efficient Concept for Elasto-plastic Simulations of Shell Responses N2 - For the analysis of arbitrary, by Finite Elements discretized shell structures, an efficient numerical simulation strategy with quadratic convergence including geometrically and physically nonlinear effects will be presented. In the beginning, a Finite-Rotation shell theory allowing constant shear deformations across the shell thickness is given in an isoparametric formulation. The assumed-strain concept enables the derivation of a locking-free finite element. The Layered Approach will be applied to ensure a sufficiently precise prediction of the propagation of plastic zones even throughout the shell thickness. The Riks-Wempner-Wessels global iteration scheme will be enhanced by a Line-Search procedure to ensure the tracing of nonlinear deformation paths with rather great load steps even in the post-peak range. The elastic-plastic material model includes isotropic hardening. A new Operator-Split return algorithm ensures considerably exact solution of the initial-value problem even for greater load steps. The combination with consistently linearized constitutive equations ensures quadratic convergence in a close neighbourhood to the exact solution. Finally, several examples will demonstrate accuracy and numerical efficiency of the developed algorithm. KW - Schale KW - Elastoplastizität KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4364 ER - TY - THES A1 - Lehmkuhl, Hansjörg T1 - Zur praktischen Anwendung numerischer Analysemethoden für Stabilitätsprobleme T1 - The application of numerical methods to stability problems in practice N2 - In der täglichen Ingenieurpraxis werden in zunehmenden Maße numerische Analysen im Rahmen der Finite-Elemente-Methode auch zur Untersuchung stabilitätsgefährdeter Strukturen eingesetzt. Für die aktuelle Praxis, insbesondere im konstruktiven Stahlbau, ist jedoch festzustellen, dass zwischen der fortgeschrittenen Theorie und dem Niveau der praktischen Anwendung numerischer Stabilitätsanalysen eine große Kluft besteht. Aus praktischer Sicht erscheint es unumgänglich, die weiter wachsende Diskrepanz zwischen den umfangreichen theoretischen Möglichkeiten und der gegenwärtigen Praxis abzubauen. Damit steht der praktisch tätige Ingenieur vor der Aufgabe, sein Wissen auf dem Gebiet numerischer Stabilitätsanalysen zu vertiefen und bereits vorhandene FE-Programme um Berechnungsalgorithmen für umfassende numerische Stabilitätsanalysen zu erweitern. Dafür werden in der Arbeit die Grundlagen einer FEM- orientierten modernen Stabilitätstheorie einheitlich und aus Sicht einer praktischen Anwendung aufbereitet. Die Darstellung von realisierten programmtechnischen Umsetzungen für erweiterte Analysenmethoden wie Nachbeulanalysen, Pfadwechsel und Approximationen imperfekter Pfade ermöglicht eine Erweiterung des Methodenvorrates. Die innerhalb der Arbeit untersuchten Beispiele zeigen, dass durch die Anwendung der behandelten Verfahren das Tragverhalten einer stabilitätsgefährdeten Struktur wesentlich besser eingeschätzt werden kann als bei Beschränkung auf die herkömmlichen Analysemethoden. N2 - The daily engineering practice is characterized by an increasing use of numerical analyses also for structures influenced by stability problems. However it must be noticed that in practice, especially in steel construction, exists a large gap between the advanced stability theory and the level of practical applications of numerical stability analyses. From a practical point of view it seems be absolutely necessary to break up the continual growing discrepancy between comprehensive theoretical possibilities and current practice. Therefore practical engineers have to deepen their knowledge on the field of numerical stability analyses and have to expand existing finite element programs with special algorithms. For this purpose basics of a finite element orientated modern stability theory are presented from the view of practical application. Furthermore steps are shown for programming special methods like post-buckling analyses, path switching and approximations for load-deformation pathes including imperfections. The importance of the additional methods for a better understanding of the structures stability behaviour clearly comes out by the presentation of different examples of practical relevance. KW - Nichtlineare Stabilitätstheorie KW - Finite-Elemente-Methode KW - Stabilität KW - Stahlbau KW - Imperfektion KW - Nachbeulverhalten KW - Schale KW - Non-linear buckling KW - Finite Element Method KW - stability theory KW - post-buckling analysis KW - koiter approximation Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20051013-7102 ER - TY - THES A1 - Gundermann, Ralf T1 - 3D-Simulation des Temperaturfeldes und der Gefügeumwandlung bei einer Laserstrahlschweißung T1 - 3D-simulation the temperature field and the material transformation at a laser beam welding N2 - Das FEM-Programmsystem „SYSWELD“ kommt für die Berechnung des Temperaturfeldes bei einer Laserstrahlschweißung zum Einsatz. Insbesondere sollen der Einfluss des Energieeintrages und die damit verbundene Gefügeumwandlung eines Feinkornbaustahles untersucht und Aussagen zur notwendigen Modellierungsgenauigkeit der Nahtgeometrie bzw. Netzverfeinerung getroffen werden. Im Einzelnen sind folgende Teilaufgaben zu lösen: - ausführliche Literaturrecherche zur numerischen Analyse von Schweißverbindungen insbesondere zu temperaturabhängigen Materialeigenschaften von Feinkornbaustählen, - Darstellung der Wärmequelle für das Laserstrahlschweißen, - Erprobung unterschiedlicher Netzvarianten für die FE-Analyse von instationären Temperaturfeldern, - Untersuchung zur Modellierungsgenauigkeit der Nahtgeometrie, - Parameterstudien zum Einfluss der Materialkennwerte und Gefügekinetik auf das Temperaturfeld sowie das Gefüge. N2 - The FEM-program "SYSWELD" comes for the calculation the temperature field at a laser beam welding to the employment. Particularly the influence of the energy deposit should explored and the with it joined material transformation of a fine grained steel and are met statements to the necessary modelling precision the weld geometry and mesh refinement. In the single following tasks are to be solved: - Comprehensive literature investigation to the numerical analysis of welding joints particularly to temperature dependent material properties of fine grained steels, - Display the heat source for the laser beam welding, - Test different mesh variants for the Fe-analysis of non-stationary temperature fields, - Investigation to the modelling precision on the weld geometry, - Investigation to the influence the material properties and material transformation on the temperature field as well as the material structure. KW - Laserschweißen KW - Finite-Elemente-Methode KW - Direkte numerische Simulation KW - Gefügeumwandlung KW - Feinkornbaustahl KW - Temperaturfeld KW - Laserstrahlschweißen KW - Aufheizraten KW - ZTU-Schaubild KW - laser beam KW - joint weld KW - fine grained steel Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6680 N1 - Der Volltext-Zugang wurde im Zusammenhang mit der Klärung urheberrechtlicher Fragen mit sofortiger Wirkung gesperrt. ER -