TY - THES A1 - Schrader, Kai T1 - Hybrid 3D simulation methods for the damage analysis of multiphase composites T1 - Hybride 3D Simulationsmethoden zur Abbildung der Schädigungsvorgänge in Mehrphasen-Verbundwerkstoffen N2 - Modern digital material approaches for the visualization and simulation of heterogeneous materials allow to investigate the behavior of complex multiphase materials with their physical nonlinear material response at various scales. However, these computational techniques require extensive hardware resources with respect to computing power and main memory to solve numerically large-scale discretized models in 3D. Due to a very high number of degrees of freedom, which may rapidly be increased to the two-digit million range, the limited hardware ressources are to be utilized in a most efficient way to enable an execution of the numerical algorithms in minimal computation time. Hence, in the field of computational mechanics, various methods and algorithms can lead to an optimized runtime behavior of nonlinear simulation models, where several approaches are proposed and investigated in this thesis. Today, the numerical simulation of damage effects in heterogeneous materials is performed by the adaption of multiscale methods. A consistent modeling in the three-dimensional space with an appropriate discretization resolution on each scale (based on a hierarchical or concurrent multiscale model), however, still contains computational challenges in respect to the convergence behavior, the scale transition or the solver performance of the weak coupled problems. The computational efficiency and the distribution among available hardware resources (often based on a parallel hardware architecture) can significantly be improved. In the past years, high-performance computing (HPC) and graphics processing unit (GPU) based computation techniques were established for the investigationof scientific objectives. Their application results in the modification of existing and the development of new computational methods for the numerical implementation, which enables to take advantage of massively clustered computer hardware resources. In the field of numerical simulation in material science, e.g. within the investigation of damage effects in multiphase composites, the suitability of such models is often restricted by the number of degrees of freedom (d.o.f.s) in the three-dimensional spatial discretization. This proves to be difficult for the type of implementation method used for the nonlinear simulation procedure and, simultaneously has a great influence on memory demand and computational time. In this thesis, a hybrid discretization technique has been developed for the three-dimensional discretization of a three-phase material, which is respecting the numerical efficiency of nonlinear (damage) simulations of these materials. The increase of the computational efficiency is enabled by the improved scalability of the numerical algorithms. Consequently, substructuring methods for partitioning the hybrid mesh were implemented, tested and adapted to the HPC computing framework using several hundred CPU (central processing units) nodes for building the finite element assembly. A memory-efficient iterative and parallelized equation solver combined with a special preconditioning technique for solving the underlying equation system was modified and adapted to enable combined CPU and GPU based computations. Hence, it is recommended by the author to apply the substructuring method for hybrid meshes, which respects different material phases and their mechanical behavior and which enables to split the structure in elastic and inelastic parts. However, the consideration of the nonlinear material behavior, specified for the corresponding phase, is limited to the inelastic domains only, and by that causes a decreased computing time for the nonlinear procedure. Due to the high numerical effort for such simulations, an alternative approach for the nonlinear finite element analysis, based on the sequential linear analysis, was implemented in respect to scalable HPC. The incremental-iterative procedure in finite element analysis (FEA) during the nonlinear step was then replaced by a sequence of linear FE analysis when damage in critical regions occured, known in literature as saw-tooth approach. As a result, qualitative (smeared) crack initiation in 3D multiphase specimens has efficiently been simulated. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2013,2 KW - high-performance computing KW - finite element method KW - heterogeneous material KW - domain decomposition KW - scalable smeared crack analysis KW - FEM KW - multiphase KW - damage KW - HPC KW - solver Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20131021-20595 ER - TY - JOUR A1 - Ghazvinei, Pezhman Taherei A1 - Darvishi, Hossein Hassanpour A1 - Mosavi, Amir A1 - Yusof, Khamaruzaman bin Wan A1 - Alizamir, Meysam A1 - Shamshirband, Shahaboddin A1 - Chau, Kwok-Wing T1 - Sugarcane growth prediction based on meteorological parameters using extreme learning machine and artificial neural network JF - Engineering Applications of Computational Fluid Mechanics N2 - Management strategies for sustainable sugarcane production need to deal with the increasing complexity and variability of the whole sugar system. Moreover, they need to accommodate the multiple goals of different industry sectors and the wider community. Traditional disciplinary approaches are unable to provide integrated management solutions, and an approach based on whole systems analysis is essential to bring about beneficial change to industry and the community. The application of this approach to water management, environmental management and cane supply management is outlined, where the literature indicates that the application of extreme learning machine (ELM) has never been explored in this realm. Consequently, the leading objective of the current research was set to filling this gap by applying ELM to launch swift and accurate model for crop production data-driven. The key learning has been the need for innovation both in the technical aspects of system function underpinned by modelling of sugarcane growth. Therefore, the current study is an attempt to establish an integrate model using ELM to predict the concluding growth amount of sugarcane. Prediction results were evaluated and further compared with artificial neural network (ANN) and genetic programming models. Accuracy of the ELM model is calculated using the statistics indicators of Root Means Square Error (RMSE), Pearson Coefficient (r), and Coefficient of Determination (R2) with promising results of 0.8, 0.47, and 0.89, respectively. The results also show better generalization ability in addition to faster learning curve. Thus, proficiency of the ELM for supplementary work on advancement of prediction model for sugarcane growth was approved with promising results. KW - Künstliche Intelligenz KW - Sustainable production KW - ELM KW - prediction KW - machine learning KW - sugarcane KW - estimation KW - growth mode KW - extreme learning machine KW - OA-Publikationsfonds2018 Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20181017-38129 UR - https://www.tandfonline.com/doi/full/10.1080/19942060.2018.1526119 VL - 2018 IS - 12,1 SP - 738 EP - 749 PB - Taylor & Francis ER - TY - JOUR A1 - Faizollahzadeh Ardabili, Sina A1 - Najafi, Bahman A1 - Alizamir, Meysam A1 - Mosavi, Amir A1 - Shamshirband, Shahaboddin A1 - Rabczuk, Timon T1 - Using SVM-RSM and ELM-RSM Approaches for Optimizing the Production Process of Methyl and Ethyl Esters JF - Energies N2 - The production of a desired product needs an effective use of the experimental model. The present study proposes an extreme learning machine (ELM) and a support vector machine (SVM) integrated with the response surface methodology (RSM) to solve the complexity in optimization and prediction of the ethyl ester and methyl ester production process. The novel hybrid models of ELM-RSM and ELM-SVM are further used as a case study to estimate the yield of methyl and ethyl esters through a trans-esterification process from waste cooking oil (WCO) based on American Society for Testing and Materials (ASTM) standards. The results of the prediction phase were also compared with artificial neural networks (ANNs) and adaptive neuro-fuzzy inference system (ANFIS), which were recently developed by the second author of this study. Based on the results, an ELM with a correlation coefficient of 0.9815 and 0.9863 for methyl and ethyl esters, respectively, had a high estimation capability compared with that for SVM, ANNs, and ANFIS. Accordingly, the maximum production yield was obtained in the case of using ELM-RSM of 96.86% for ethyl ester at a temperature of 68.48 °C, a catalyst value of 1.15 wt. %, mixing intensity of 650.07 rpm, and an alcohol to oil molar ratio (A/O) of 5.77; for methyl ester, the production yield was 98.46% at a temperature of 67.62 °C, a catalyst value of 1.1 wt. %, mixing intensity of 709.42 rpm, and an A/O of 6.09. Therefore, ELM-RSM increased the production yield by 3.6% for ethyl ester and 3.1% for methyl ester, compared with those for the experimental data. KW - Biodiesel KW - Optimierung KW - extreme learning machine KW - machine learning KW - response surface methodology KW - support vector machine KW - OA-Publikationsfonds2018 Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20181025-38170 UR - https://www.mdpi.com/1996-1073/11/11/2889 IS - 11, 2889 SP - 1 EP - 20 PB - MDPI CY - Basel ER - TY - JOUR A1 - Ouaer, Hocine A1 - Hosseini, Amir Hossein A1 - Amar, Menad Nait A1 - Ben Seghier, Mohamed El Amine A1 - Ghriga, Mohammed Abdelfetah A1 - Nabipour, Narjes A1 - Andersen, Pål Østebø A1 - Mosavi, Amir A1 - Shamshirband, Shahaboddin T1 - Rigorous Connectionist Models to Predict Carbon Dioxide Solubility in Various Ionic Liquids JF - Applied Sciences N2 - Estimating the solubility of carbon dioxide in ionic liquids, using reliable models, is of paramount importance from both environmental and economic points of view. In this regard, the current research aims at evaluating the performance of two data-driven techniques, namely multilayer perceptron (MLP) and gene expression programming (GEP), for predicting the solubility of carbon dioxide (CO2) in ionic liquids (ILs) as the function of pressure, temperature, and four thermodynamical parameters of the ionic liquid. To develop the above techniques, 744 experimental data points derived from the literature including 13 ILs were used (80% of the points for training and 20% for validation). Two backpropagation-based methods, namely Levenberg–Marquardt (LM) and Bayesian Regularization (BR), were applied to optimize the MLP algorithm. Various statistical and graphical assessments were applied to check the credibility of the developed techniques. The results were then compared with those calculated using Peng–Robinson (PR) or Soave–Redlich–Kwong (SRK) equations of state (EoS). The highest coefficient of determination (R2 = 0.9965) and the lowest root mean square error (RMSE = 0.0116) were recorded for the MLP-LMA model on the full dataset (with a negligible difference to the MLP-BR model). The comparison of results from this model with the vastly applied thermodynamic equation of state models revealed slightly better performance, but the EoS approaches also performed well with R2 from 0.984 up to 0.996. Lastly, the newly established correlation based on the GEP model exhibited very satisfactory results with overall values of R2 = 0.9896 and RMSE = 0.0201. KW - Maschinelles Lernen KW - Machine learning KW - OA-Publikationsfonds2020 Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200107-40558 UR - https://www.mdpi.com/2076-3417/10/1/304 VL - 2020 IS - Volume 10, Issue 1, 304 PB - MDPI ER - TY - JOUR A1 - Meiabadi, Mohammad Saleh A1 - Moradi, Mahmoud A1 - Karamimoghadam, Mojtaba A1 - Ardabili, Sina A1 - Bodaghi, Mahdi A1 - Shokri, Manouchehr A1 - Mosavi, Amir Hosein T1 - Modeling the Producibility of 3D Printing in Polylactic Acid Using Artificial Neural Networks and Fused Filament Fabrication JF - polymers N2 - Polylactic acid (PLA) is a highly applicable material that is used in 3D printers due to some significant features such as its deformation property and affordable cost. For improvement of the end-use quality, it is of significant importance to enhance the quality of fused filament fabrication (FFF)-printed objects in PLA. The purpose of this investigation was to boost toughness and to reduce the production cost of the FFF-printed tensile test samples with the desired part thickness. To remove the need for numerous and idle printing samples, the response surface method (RSM) was used. Statistical analysis was performed to deal with this concern by considering extruder temperature (ET), infill percentage (IP), and layer thickness (LT) as controlled factors. The artificial intelligence method of artificial neural network (ANN) and ANN-genetic algorithm (ANN-GA) were further developed to estimate the toughness, part thickness, and production-cost-dependent variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid machine learning (ML) technique could enhance the accuracy of modeling by about 7.5, 11.5, and 4.5% for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. On the other hand, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which enables the usability of printed PLA objects. KW - 3D-Druck KW - Polymere KW - Maschinelles Lernen KW - 3D printing KW - machine learning KW - fused filament fabrication KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220110-45518 UR - https://www.mdpi.com/2073-4360/13/19/3219 VL - 2021 IS - Volume 13, issue 19, article 3219 SP - 1 EP - 21 PB - MDPI CY - Basel ER - TY - JOUR A1 - Ahmadi, Mohammad Hossein A1 - Baghban, Alireza A1 - Sadeghzadeh, Milad A1 - Zamen, Mohammad A1 - Mosavi, Amir A1 - Shamshirband, Shahaboddin A1 - Kumar, Ravinder A1 - Mohammadi-Khanaposhtani, Mohammad T1 - Evaluation of electrical efficiency of photovoltaic thermal solar collector JF - Engineering Applications of Computational Fluid Mechanics N2 - In this study, machine learning methods of artificial neural networks (ANNs), least squares support vector machines (LSSVM), and neuro-fuzzy are used for advancing prediction models for thermal performance of a photovoltaic-thermal solar collector (PV/T). In the proposed models, the inlet temperature, flow rate, heat, solar radiation, and the sun heat have been considered as the input variables. Data set has been extracted through experimental measurements from a novel solar collector system. Different analyses are performed to examine the credibility of the introduced models and evaluate their performances. The proposed LSSVM model outperformed the ANFIS and ANNs models. LSSVM model is reported suitable when the laboratory measurements are costly and time-consuming, or achieving such values requires sophisticated interpretations. KW - Fotovoltaik KW - Erneuerbare Energien KW - Solar KW - Deep learning KW - Machine learning KW - Renewable energy KW - neural networks (NNs) KW - adaptive neuro-fuzzy inference system (ANFIS) KW - least square support vector machine (LSSVM) KW - photovoltaic-thermal (PV/T) KW - hybrid machine learning model KW - OA-Publikationsfonds2020 Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200304-41049 UR - https://www.tandfonline.com/doi/full/10.1080/19942060.2020.1734094 VL - 2020 IS - volume 14, issue 1 SP - 545 EP - 565 PB - Taylor & Francis ER - TY - JOUR A1 - Mosavi, Amir A1 - Shamshirband, Shahaboddin A1 - Esmaeilbeiki, Fatemeh A1 - Zarehaghi, Davoud A1 - Neyshabouri, Mohammadreza A1 - Samadianfard, Saeed A1 - Ghorbani, Mohammad Ali A1 - Nabipour, Narjes A1 - Chau, Kwok-Wing T1 - Comparative analysis of hybrid models of firefly optimization algorithm with support vector machines and multilayer perceptron for predicting soil temperature at different depths JF - Engineering Applications of Computational Fluid Mechanics N2 - This research aims to model soil temperature (ST) using machine learning models of multilayer perceptron (MLP) algorithm and support vector machine (SVM) in hybrid form with the Firefly optimization algorithm, i.e. MLP-FFA and SVM-FFA. In the current study, measured ST and meteorological parameters of Tabriz and Ahar weather stations in a period of 2013–2015 are used for training and testing of the studied models with one and two days as a delay. To ascertain conclusive results for validation of the proposed hybrid models, the error metrics are benchmarked in an independent testing period. Moreover, Taylor diagrams utilized for that purpose. Obtained results showed that, in a case of one day delay, except in predicting ST at 5 cm below the soil surface (ST5cm) at Tabriz station, MLP-FFA produced superior results compared with MLP, SVM, and SVM-FFA models. However, for two days delay, MLP-FFA indicated increased accuracy in predicting ST5cm and ST 20cm of Tabriz station and ST10cm of Ahar station in comparison with SVM-FFA. Additionally, for all of the prescribed models, the performance of the MLP-FFA and SVM-FFA hybrid models in the testing phase was found to be meaningfully superior to the classical MLP and SVM models. KW - Bodentemperatur KW - Algorithmus KW - Maschinelles Lernen KW - Neuronales Netz KW - firefly optimization algorithm KW - soil temperature KW - artificial neural networks KW - hybrid machine learning KW - OA-Publikationsfonds2019 Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200911-42347 UR - https://www.tandfonline.com/doi/full/10.1080/19942060.2020.1788644 VL - 2020 IS - Volume 14, Issue 1 SP - 939 EP - 953 ER - TY - JOUR A1 - Homaei, Mohammad Hossein A1 - Soleimani, Faezeh A1 - Shamshirband, Shahaboddin A1 - Mosavi, Amir A1 - Nabipour, Narjes A1 - Varkonyi-Koczy, Annamaria R. T1 - An Enhanced Distributed Congestion Control Method for Classical 6LowPAN Protocols Using Fuzzy Decision System JF - IEEE Access N2 - The classical Internet of things routing and wireless sensor networks can provide more precise monitoring of the covered area due to the higher number of utilized nodes. Because of the limitations in shared transfer media, many nodes in the network are prone to the collision in simultaneous transmissions. Medium access control protocols are usually more practical in networks with low traffic, which are not subjected to external noise from adjacent frequencies. There are preventive, detection and control solutions to congestion management in the network which are all the focus of this study. In the congestion prevention phase, the proposed method chooses the next step of the path using the Fuzzy decision-making system to distribute network traffic via optimal paths. In the congestion detection phase, a dynamic approach to queue management was designed to detect congestion in the least amount of time and prevent the collision. In the congestion control phase, the back-pressure method was used based on the quality of the queue to decrease the probability of linking in the pathway from the pre-congested node. The main goals of this study are to balance energy consumption in network nodes, reducing the rate of lost packets and increasing quality of service in routing. Simulation results proved the proposed Congestion Control Fuzzy Decision Making (CCFDM) method was more capable in improving routing parameters as compared to recent algorithms. KW - Internet der dinge KW - IOT KW - Internet of things KW - wireless sensor network KW - congestion control KW - fuzzy decision making KW - back-pressure Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200213-40805 UR - https://ieeexplore.ieee.org/document/8967114 IS - volume 8 SP - 20628 EP - 20645 PB - IEEE ER - TY - JOUR A1 - Hassannataj Joloudari, Javad A1 - Hassannataj Joloudari, Edris A1 - Saadatfar, Hamid A1 - GhasemiGol, Mohammad A1 - Razavi, Seyyed Mohammad A1 - Mosavi, Amir A1 - Nabipour, Narjes A1 - Shamshirband, Shahaboddin A1 - Nadai, Laszlo T1 - Coronary Artery Disease Diagnosis: Ranking the Significant Features Using a Random Trees Model JF - International Journal of Environmental Research and Public Health, IJERPH N2 - Heart disease is one of the most common diseases in middle-aged citizens. Among the vast number of heart diseases, coronary artery disease (CAD) is considered as a common cardiovascular disease with a high death rate. The most popular tool for diagnosing CAD is the use of medical imaging, e.g., angiography. However, angiography is known for being costly and also associated with a number of side effects. Hence, the purpose of this study is to increase the accuracy of coronary heart disease diagnosis through selecting significant predictive features in order of their ranking. In this study, we propose an integrated method using machine learning. The machine learning methods of random trees (RTs), decision tree of C5.0, support vector machine (SVM), and decision tree of Chi-squared automatic interaction detection (CHAID) are used in this study. The proposed method shows promising results and the study confirms that the RTs model outperforms other models. KW - Maschinelles Lernen KW - Machine learning KW - Deep learning KW - coronary artery disease KW - heart disease diagnosis KW - health informatics KW - data science KW - big data KW - predictive model KW - ensemble model KW - random forest KW - industry 4.0 Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200213-40819 UR - https://www.mdpi.com/1660-4601/17/3/731 VL - 2020 IS - Volume 17, Issue 3, 731 PB - MDPI ER - TY - JOUR A1 - Kargar, Katayoun A1 - Samadianfard, Saeed A1 - Parsa, Javad A1 - Nabipour, Narjes A1 - Shamshirband, Shahaboddin A1 - Mosavi, Amir A1 - Chau, Kwok-Wing T1 - Estimating longitudinal dispersion coefficient in natural streams using empirical models and machine learning algorithms JF - Engineering Applications of Computational Fluid Mechanics N2 - The longitudinal dispersion coefficient (LDC) plays an important role in modeling the transport of pollutants and sediment in natural rivers. As a result of transportation processes, the concentration of pollutants changes along the river. Various studies have been conducted to provide simple equations for estimating LDC. In this study, machine learning methods, namely support vector regression, Gaussian process regression, M5 model tree (M5P) and random forest, and multiple linear regression were examined in predicting the LDC in natural streams. Data sets from 60 rivers around the world with different hydraulic and geometric features were gathered to develop models for LDC estimation. Statistical criteria, including correlation coefficient (CC), root mean squared error (RMSE) and mean absolute error (MAE), were used to scrutinize the models. The LDC values estimated by these models were compared with the corresponding results of common empirical models. The Taylor chart was used to evaluate the models and the results showed that among the machine learning models, M5P had superior performance, with CC of 0.823, RMSE of 454.9 and MAE of 380.9. The model of Sahay and Dutta, with CC of 0.795, RMSE of 460.7 and MAE of 306.1, gave more precise results than the other empirical models. The main advantage of M5P models is their ability to provide practical formulae. In conclusion, the results proved that the developed M5P model with simple formulations was superior to other machine learning models and empirical models; therefore, it can be used as a proper tool for estimating the LDC in rivers. KW - Maschinelles Lernen KW - Gaussian process regression KW - longitudinal dispersion coefficient KW - M5 model tree KW - random forest KW - support vector regression KW - rivers Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200128-40775 UR - https://www.tandfonline.com/doi/full/10.1080/19942060.2020.1712260 VL - 2020 IS - Volume 14, No. 1 SP - 311 EP - 322 PB - Taylor & Francis ER -