TY - THES A1 - Karaki, Ghada T1 - Assessment of coupled models of bridges considering time-dependent vehicular loading N2 - Bridge vibration due to traffic loading has been a subject of extensive research in the last decades. The focus of such research has been to develop solution algorithms and investigate responses or behaviors of interest. However, proving the quality and reliability of the model output in structural engineering has become a topic of increasing importance. Therefore, this study is an attempt to extend concepts of uncertainty and sensitivity analyses to assess the dynamic response of a coupled model in bridge engineering considering time-dependent vehicular loading. A setting for the sensitivity analysis is proposed, which enables performing the sensitivity analysis considering random stochastic processes. The classical and proposed sensitivity settings are used to identify the relevant input parameters and models that have the most influence on the variance of the dynamic response. The sensitivity analysis exercises the model itself and extracts results without the need for measurements or reference solutions; however, it does not offer a means of ranking the coupled models studied. Therefore, concepts of total uncertainty are employed to rank the coupled models studied according to their fitness in describing the dynamic problem. The proposed procedures are applied in two examples to assess the output of coupled subsystems and coupled partial models in bridge engineering considering the passage of a heavy vehicle at various speeds. N2 - Brückenschwingungen infolge von Verkehrslasten sind seit mehreren Jahrzehnten Gegenstand intensiver Forschung. Im Fokus stand hierbei im Besonderen die Entwicklung von Lösungsalgorithmen zur Ermittlung des dynamischen Bauwerkverhaltens. Begleitet ist diese Entwicklung von der Frage nach der Qualität und Zuverlässigkeit dieser Modelle für den Gebrauch im konstruktiven Ingenieurbau. In diesem Zusammenhang werden in der vorliegenden Arbeit Konzepte der Unsicherheits- und Sensitivitätsanalyse erweitert, um das dynamische Bauwerkverhalten unter Berücksichtigung transienter Fahrzeuglasten bei gekoppelten Modellen des Brückenbaus zu bewerten. Bestehende Sensitivitätsanalysen werden ergänzt, um diese auch unter Berücksichtigung von stochastischen Prozessen durchführen zu können. Die klassische und die erweiterte Methode werden angewandt, um relevante Eingangsparameter sowie Partialmodelle mit wesentlichem Einfluss auf die Varianz der dynamischen Strukturantwort zu identifizieren. Die mit Hilfe der Sensitivitätsanalyse ermittelbaren Kennzahlen können ohne Bezug zu einer Referenzlösung in die Modellbewertung einfließen, allerdings ist es nicht möglich, die Modelle hinsichtlich der realitätsnahen Abbildung des dynamischen Problems zu bewerten. Um dies zu ermöglichen, wurden Konzepte der Gesamtunsicherheit verwendet. Die vorgestellten Methoden wurden auf zwei Beispiele angewandt, um die Ergebnisse von gekoppelten Subsystemen und gekoppelten Partialmodellen des Brückenbaus zu evaluieren. Hierbei handelt es sich um die Überfahrt von schweren Fahrzeugen mit verschiedenen Geschwindigkeiten. T3 - Schriftenreihe des DFG Graduiertenkollegs 1462 Modellqualitäten // Graduiertenkolleg Modellqualitäten - 5 KW - Ingenieurbau KW - bridge-vehicle interaction KW - random vibrations KW - sensitivity and uncertainty analysis Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120402-15894 ER - TY - THES A1 - Hatahet, Tareq T1 - On the Analysis of the Disproportionate Structural Collapse in RC Buildings N2 - Increasing structural robustness is the goal which is of interest for structural engineering community. The partial collapse of RC buildings is subject of this dissertation. Understanding the robustness of RC buildings will guide the development of safer structures against abnormal loading scenarios such as; explosions, earthquakes, fine, and/or long-term accumulation effects leading to deterioration or fatigue. Any of these may result in local immediate structural damage, that can propagate to the rest of the structure causing what is known by the disproportionate collapse. This work handels collapse propagation through various analytical approaches which simplifies the mechanical description of damaged reinfoced concrete structures due to extreme acidental event. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2018,2 KW - Beton KW - disproportionate collapse KW - buildings KW - reinforced concrete KW - catenary action KW - compressive arching KW - dynamic amplifification KW - structural robustness Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20180329-37405 ER - TY - THES A1 - Gerold, Fabian T1 - Konzepte zur interaktiven Entwurfsraum-Exploration im Tragwerksentwurf N2 - Der Entwurfsraum für den Entwurf eines Tragwerks ist ein n-dimensionaler Raum, der aus allen freien Parametern des Modells aufgespannt wird. Traditionell werden nur wenige Punkte dieses Raumes durch eine numerische (computergestützte) Simulation evaluiert, meist auf Basis der Finite-Elemente-Methode. Mehrere Faktoren führen dazu, dass heute oft viele Revisionen eines Simulationsmodells durchlaufen werden: Zum einen ergeben sich oft Planungsänderungen, zum anderen ist oft die Untersuchung von Planungsalternativen und die Suche nach einem Optimum wünschenswert. In dieser Arbeit soll für ein vorhandenes Finite-Elemente-Framework die sequentielle Datei-Eingabeschnittstelle durch eine Netzwerkschnittstelle ersetzt werden, die den Erfordernissen einer interaktiven Arbeitsweise entspricht. So erlaubt die hier konzipierte Schnittstelle interaktive, inkrementelle Modelländerungen sowie Status- und Berechnungsergebnis-Abfragen durch eine bidirektionale Schnittstelle. Die Kombination aus interaktiver numerischer Simulation und Interoperabilität durch die Anwendung von Konzepten zur Bauwerks-Informations-Modellierung im Tragwerksentwurf ist Ziel dieser Dissertation. Die Beschreibung der Konzeption und prototypischen Umsetzung ist Gegenstand der schriftlichen Arbeit. KW - Interaktive numerische Simulation KW - Industry Foundation Classes (IFC) Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20140408-21532 ER - TY - THES A1 - Keitel, Holger T1 - Bewertungsmethoden für die Prognosequalität von Kriechmodellen des Betons T1 - Evaluation Methods for Prediction Quality of Concrete Creep Models N2 - Ziel dieser Arbeit ist die Entwicklung von Methoden, mit denen die Prognosequalität von Kriechmodellen des Betons bestimmt werden kann. Die Methoden werden in zwei Ausgangsszenarien unterschieden: die Bewertung ohne und die Bewertung mit Verwendung von spezifischen Versuchsdaten zum Kriechverhalten des Betons. Die Modellqualität wird anhand der Gesamtunsicherheit der prognostizierten Kriechnachgiebigkeit quantifiziert. Die Unsicherheit wird für die Kriechprognose ohne Versuchsdaten über eine Unsicherheitsanalyse unter Berücksichtigung korrelierter Eingangsparameter ermittelt. Bei der Verwendung experimenteller Daten werden die stochastischen Eigenschaften der Modellparameter mittels Bayesian Updating bestimmt. Die Bewertung erfolgt erneut basierend auf einer Unsicherheitsanalyse sowie alternativ mittels Modellselektion nach Bayes. Weiterhin wird eine auf Graphentheorie und Sensitivitätsanalysen basierende Methode zur Bewertung von gekoppelten Partialmodellen entwickelt. Damit wird der Einfluss eines Partialmodells auf das Verhalten einer globalen Tragstruktur quantifiziert, Interaktionen von Partialmodellen festgestellt und ein Maß für die Qualität eines Gesamtmodells ermittelt. N2 - The goal of this doctoral thesis is the development of methods for the evaluation of the prediction quality of concrete creep models. The methods are distinguished into two scenarios: the evaluation with and without experimental data about the creep behavior of concrete. The model quality is quantified by the total uncertainty of the predicted creep compliance. The uncertainty of the creep prognosis without using measurement data is quantified by an uncertainty analysis taking into account the parameter correlation. When experimental data is considered the stochastic properties of the creep model parameters are found by means of Bayesian Updating. The evaluation is once more based on an uncertainty analysis or, alternatively, applying Bayesian model selection. Further, an assessment method of coupled partial models based on graph theory and sensitivity analysis is developed. Therewith, the influence of classes of partial models on the global model response is quantified, interactions of partial models are detected, and a measure for the quality of the global model is derived. T3 - Schriftenreihe des DFG Graduiertenkollegs 1462 Modellqualitäten // Graduiertenkolleg Modellqualitäten - 2 KW - Kriechen KW - Bewertung KW - Prognosequalität KW - Bayes-Inferenz KW - Unsicherheitsanalyse KW - Gekoppelte Modelle KW - Coupled models KW - Bewertungsmethode KW - Evaluation methods Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120207-15569 SN - 978-3-86068-466-5 PB - Verlag der Bauhaus-Universität Weimar CY - Weimar ER - TY - THES A1 - Mai, Luu T1 - Structural Control Systems in High-speed Railway Bridges N2 - Structural vibration control of high-speed railway bridges using tuned mass dampers, semi-active tuned mass dampers, fluid viscous dampers and magnetorheological dampers to reduce resonant structural vibrations is studied. In this work, the addressed main issues include modeling of the dynamic interaction of the structures, optimization of the parameters of the dampers and comparison of their efficiency. A new approach to optimize multiple tuned mass damper systems on an uncertain model is proposed based on the H-infinity optimization criteria and the DK iteration procedure with norm-bounded uncertainties in frequency domain. The parameters of tuned mass dampers are optimized directly and simultaneously on different modes contributing significantly to the multi-resonant peaks to explore the different possible combinations of parameters. The effectiveness of the present method is also evaluated through comparison with a previous method. In the case of semi-active tuned mass dampers, an optimization algorithm is derived to control the magnetorheological damper in these semi-active damping systems. The use of the proposed algorithm can generate various combinations of control gains and state variables. This can lead to the improvement of the ability of MR dampers to track the desired control forces. An uncertain model to reduce detuning effects is also considered in this work. Next, for fluid viscous dampers, in order to tune the optimal parameters of fluid viscous dampers to the vicinity of the exact values, analytical formulae which can include structural damping are developed based on the perturbation method. The proposed formulae can also be considered as an improvement of the previous analytical formulae, especially for bridge beams with large structural damping. Finally, a new combination of magnetorheological dampers and a double-beam system to improve the performance of the primary structure vibration is proposed. An algorithm to control magnetorheological dampers in this system is developed by using standard linear matrix inequality techniques. Weight functions as a loop shaping procedure are also introduced in the feedback controllers to improve the tracking ability of magnetorheological damping forces. To this end, the effectiveness of magnetorheological dampers controlled by the proposed scheme, along with the effects of the uncertain and time-delay parameters on the models, are evaluated through numerical simulations. Additionally, a comparison of the dampers based on their performance is also considered in this work. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2014,3 KW - High-speed railway bridge KW - Control system KW - Passive damper KW - Semi-active damper KW - Railway bridges Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20141223-23391 SN - 1610-7381 ER - TY - THES A1 - Janke, Lars T1 - Tragverhalten von Betondruckgliedern mit vorgespannter Umschnürung aus Formgedächtnislegierungen, Stahl oder faserverstärkten Kunststoffen N2 - Druckbeanspruchte Bauteile aus Beton können mit zugfesten Umschnürungen von außen verstärkt werden. Mit dieser etablierten Methode konnten axiale Traglast und Duktilität von unzureichend bewehrten Stützen bereits verbessert werden. Es wurde jedoch festgestellt, dass der umschnürte Betonkern dennoch an Festigkeit verliert. Um die Wirksamkeit der Umschnürung zu erhöhen, wird deshalb vorgeschlagen, das umschnürende Material vorzuspannen. Dieser Vorschlag wird insbesondere von der neuen Materialgruppe der Formgedächtnislegierungen inspiriert, die thermisch vorspannbar sind. Bisher sind die Auswirkungen der Vorspannung einer Umschnürung auf das Tragverhalten von Betondruckgliedern kaum untersucht worden. Diese Lücke wird durch systematische Versuche an Betonzylindern mit vorgespannter Umschnürung aus Stahl und kohlenstofffaserverstärktem Kunststoff geschlossen. Die Abbildung der Versuchsergebnisse durch geeignete Modelle ermöglicht auch Aussagen zum Verhalten von Betondruckgliedern mit Umschnürungen aus anderen Materialien, beispielsweise Formgedächtnislegierungen. Um diese in den Berechnungen zu simulieren, wird eine für das Bauwesen infrage kommende eisenbasierte Legierung in separaten axialen Versuchen charakterisiert und thermisch vorgespannt. Die in der vorliegenden Arbeit entwickelten neuen Modelle orientieren sich im Wesentlichen an zwei Zielen: dem Abbilden des mehraxialen Spannungs-Dehnungs-Verhaltens des vorgespannt umschnürten Betons und dem Berechnen der Restfestigkeit des Betons. Die durchgeführten Versuche und Parameterstudien auf Basis der Modelle zeigen: Die Vorspannung der Umschnürung beeinflusst vor allem die Restfestigkeit des Betons wesentlich. Die gewonnenen Erkenntnisse und neuen Methoden können eingesetzt werden, um das Tragverhalten von Betondruckgliedern mit Umschnürungen aus Stahl, faserverstärktem Kunststoff oder Formgedächtnislegierungen zu bewerten. KW - Beton KW - Vorspannung KW - Formgedächtnis KW - Restfestigkeit KW - Stütze KW - Formänderungsenergie KW - Umschnürung KW - Modellierung KW - Verstärkung KW - faserverstärkt Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20141023-23262 ER - TY - THES A1 - Jaouadi, Zouhour T1 - Pareto and Reliability-Oriented Aeroelastic Shape Optimization of Bridge Decks N2 - Due to the development of new technologies and materials, optimized bridge design has recently gained more attention. The aim is to reduce the bridge components materials and the CO2 emission from the cement manufacturing process. Thus, most long-span bridges are designed to be with high flexibility, low structural damping, and longer and slender spans. Such designs lead, however, to aeroelastic challenges. Moreover, the consideration of both the structural and aeroelastic behavior in bridges leads to contradictory solutions as the structural constraints lead to deck prototypes with high depth which provide high inertia to material volume ratios. On the other hand, considering solely the aerodynamic requirements, slender airfoil-shaped bridge box girders are recommended since they prevent vortex shedding and exhibit minimum drag. Within this framework comes this study which provides approaches to find optimal bridge deck cross-sections while considering the aerodynamic effects. Shape optimization of deck cross-section is usually formulated to minimize the amount of material by finding adequate parameters such as the depth, the height, and the thickness and while ensuring the overall stability of the structure by the application of some constraints. Codes and studies have been implemented to analyze the wind phenomena and the structural responses towards bridge deck cross-sections where simplifications have been adopted due to the complexity and the uniqueness of such components besides the difficulty of obtaining a final model of the aerodynamic behavior. In this thesis, two main perspectives have been studied; the first is fully deterministic and presents a novel framework on generating optimal aerodynamic shapes for streamlined and trapezoidal cross-sections based on the meta-modeling approach. Single and multi-objective optimizations were both carried out and a Pareto Front is generated. The performance of the optimal designs is checked afterwards. In the second part, a new strategy based on Reliability-Based Design Optimization (RBDO) to mitigate the vortex-induced vibration (VIV) on the Trans-Tokyo Bay bridge is proposed. Small changes in the leading and trailing edges are presented and uncertainties are considered in the structural system. Probabilistic constraints based on polynomial regression are evaluated and the problem is solved while applying the Reliability Index Approach (RIA) and the Performance Measure Approach (PMA). The results obtained in the first part showed that the aspect ratio has a significant effect on the aerodynamic behavior where deeper cross-sections have lower resistance against flutter and should be avoided. In the second part, the adopted RBDO approach succeeded to mitigate the VIV, and it is proven that designs with narrow or prolonged bottom-base length and featuring an abrupt surface change in the leading and trailing edges can lead to high vertical vibration amplitude. It is expected that this research will help engineers with the selections of the adequate deck cross-section layout, and encourage researchers to apply concepts of optimization regarding this field and develop the presented approaches for further studies. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,10 KW - Gestaltoptimierung KW - Vibration KW - Deck cross-sections KW - Reliability-based design optimization KW - Shape optimization KW - Pareto Front KW - Vortex-induced vibration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230303-49352 ER - TY - THES A1 - Bendalla, Abdulmagid Sedig Khalafallah T1 - Nonlinear Numerical Modelling of Cable Elements in Bridges for Dynamic Analysis N2 - Identifying cable force with vibration-based methods has become widely used in engineering practice due to simplicity of application. The string taut theory provides a simple definition of the relationship between natural frequencies and the tension force of a cable. However, this theory assumes a perfectly flexible non-sagging cable pinned at its ends. These assumptions do not reflect all cases, especially when the cable is short, under low tension forces or the supports are partially flexible. Extradosed bridges, which are distinguished from cable-stayed bridges by their low pylon height, have shorter cables. Therefore the application of the conventional string taut theory to identify cable forces on extradosed bridge cables might be inadequate to identify cable forces. In this work, numerical modelling of an extradosed bridge cable saddled on a circular deviator at pylon is conducted. The model is validated with the catenary analytical solution and its static and dynamic behaviours are studied. The effect of a saddle support is found to positively affect the cable stiffness by geometric means; longer saddle radius increases the cable stiffness by suppressing the deformations near the saddle. Further, accounting the effects of bending stiffness in the numerical model by using beam elements show considerable deviation from models with truss elements (i.e. zero bending stiffness). This deviation is manifested when comparing the static and dynamic properties. This motivates a more thorough study of bending stiffness effects on short cables. Bending stiffness effects are studied using two rods connected with several springs along their length. Under bending moments, the springs resist the rods' relative axial displacement by the springs' transverse component. This concept is used to identify bending stiffness values by utilizing the parallel axis theorem to quantify ratios of the second moment of area. These ratios are calculated based on the setup of the springs (e.g. number of springs per unit length, transverse stiffness, etc...). The numerical model based on this concept agrees well with the theoretical values computed using upper and lower bounds of the parallel axis theorem. The proposed concept of quantifying ratios of the second moment of area using springs as connection between cable rods is applied on an actual extradosed bridge geometry. The model is examined by comparison to the previously validated global numerical model. The two models showed good correlation under various changing parameters. This allowed further study of the effects of stick/slip behaviour between cable rods on an actual bridge geometry. KW - Kabel KW - Nonlinear Cable Analysis KW - Bending Stiffness of cable elements KW - Biegesteifigkeit Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20191007-39940 ER - TY - THES A1 - Kavrakov, Igor T1 - Structural Optimization of Composite Cross-Sections and Elements using Energy Methods N2 - Structural optimization has gained considerable attention in the design of structural engineering structures, especially in the preliminary phase. This study introduces an unconventional approach for structural optimization by utilizing the Energy method with Integral Material Behavior (EIM), based on the Lagrange’s principle of minimum potential energy. An automated two-level optimization search process is proposed, which integrates the EIM, as an alternative method for nonlinear structural analysis, and the bilevel optimization. The proposed procedure secures the equilibrium through minimizing the potential energy on one level, and on a higher level, a design objective function. For this, the most robust strategy of bilevel optimization, the nested method is used. The function of the potential energy is investigated along with its instabilities for physical nonlinear analysis through principle examples, by which the advantages and limitations using this method are reviewed. Furthermore, optimization algorithms are discussed. A numerical fully functional code is developed for nonlinear cross section, element and 2D frame analysis, utilizing different finite elements and is verified against existing EIM programs. As a proof of concept, the method is applied on selected examples using this code on cross section and element level. For the former one a comparison is made with standard procedure, by employing the equilibrium equations within the constrains. The validation of the element level was proven by a theoretical solution of an arch bridge and finally, a truss bridge is optimized. Most of the principle examples are chosen to be adequate for the everyday engineering practice, to demonstrate the effectiveness of the proposed method. This study implies that with further development, this method could become just as competitive as the conventional structural optimization techniques using the Finite Element Method. KW - Strukturoptimierung Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20190815-39593 ER -