TY - JOUR A1 - Wiegand, Torben A1 - Osburg, Andrea T1 - Synthesis, Curing and Thermal Behavior of Amine Hardeners from Potentially Renewable Sources JF - Polymers N2 - Research into bio-based epoxy resins has intensified in recent decades. Here, it is of great importance to use raw materials whose use does not compete with food production. In addition, the performance of the newly developed materials should be comparable to that of conventional products. Possible starting materials are lignin degradation products, such as vanillin and syringaldehyde, for which new synthesis routes to the desired products must be found and their properties determined. In this article, the first synthesis of two amine hardeners, starting with vanillin and syringaldehyde, using the Smiles rearrangement reaction is reported. The amine hardeners were mixed with bisphenol A diglycidyl ether, and the curing was compared to isophorone diamine, 4-4′-diaminodiphenyl sulfone, and 4-Aminonbenzylamine by means of differential scanning calorimetry. It was found that the two amines prepared are cold-curing. As TG-MS studies showed, the thermal stability of at least one of the polymers prepared with the potentially bio-based amines is comparable to that of the polymer prepared with isophorone diamine, and similar degradation products are formed during pyrolysis. KW - Epoxide KW - Epoxidharz KW - Polymere KW - epoxy KW - amine hardener KW - curing agent KW - bio-based KW - vanillin KW - OA-Publikationsfonds2023 Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230524-63745 UR - https://www.mdpi.com/2073-4360/15/4/990 VL - 2023 IS - volume 15, issue 4, article 990 SP - 1 EP - 12 PB - MDPI CY - Basel ER - TY - JOUR A1 - Partschefeld, Stephan A1 - Wiegand, Torben A1 - Bellmann, Frank A1 - Osburg, Andrea T1 - Formation of Geopolymers Using Sodium Silicate Solution and Aluminum Orthophosphate JF - Materials N2 - This paper reports the formation and structure of fast setting geopolymers activated by using three sodium silicate solutions with different modules (1.6, 2.0 and 2.4) and a berlinite-type aluminum orthophosphate. By varying the concentration of the aluminum orthophosphate, different Si/Al-ratios were established (6, 3 and 2). Reaction kinetics of binders were determined by isothermal calorimetric measurements at 20 °C. X-ray diffraction analysis as well as nuclear magnetic resonance (NMR) measurements were performed on binders to determine differences in structure by varying the alkalinity of the sodium silicate solutions and the Si/Al-ratio. The calorimetric results indicated that the higher the alkalinity of the sodium silicate solution, the higher the solubility and degree of conversion of the aluminum orthophosphate. The results of X-ray diffraction and Rietveldt analysis, as well as the NMR measurements, confirmed the assumption of the calorimetric experiments that first the aluminum orthophosphate was dissolved and then a polycondensation to an amorphous aluminosilicate network occurred. The different amounts of amorphous phases formed as a function of the alkalinity of the sodium silicate solution, indicate that tetrahydroxoaluminate species were formed during the dissolution of the aluminum orthophosphate, which reduce the pH value. This led to no further dissolution of the aluminum orthophosphate, which remained unreacted. KW - Geopolymere KW - geopolymer KW - berlinite KW - sodium silicate solution KW - alumosilicate KW - OA-Publikationsfonds2020 Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210122-43378 UR - https://www.mdpi.com/1996-1944/13/18/4202 VL - 2020 IS - Volume 13, issue 18, article 4202 SP - 1 EP - 16 PB - MDPI CY - Basel ER - TY - CHAP A1 - Kleiner, Florian A1 - Wiegand, Torben A1 - Osburg, Andrea T1 - Eigenschaftsentwicklung epoxidharzmodifizierter Mörtel auf Zementbasis bei unterschiedlichen klimatischen Bedingungen T2 - Tagung Bauchemie der GDCh-Fachgruppe Bauchemie, 18.-20. September 2017 in Weimar N2 - Zur Erstellung von dekorativen Plastiken sollten Mörtel entwickelt werden, die eine hohe Biegezugfestigkeit aufweisen und eine breite Palette von Konsistenzen für verschiedene Anwendungsarten, wie Gießen, Spachteln oder Stampfen abdecken. Als Basis für die Rezepturen wurde ein niedrigviskoses Epoxidharzsystem gewählt, dessen Aminhärter einen Wasseranteil von 44 % beinhaltet. Dies ermöglichte es, durch Wasserzugabe verschiedene Viskositäten einzustellen. Um dieses Wasser in massiveren Bauteilen zu binden, wurde neben Sand auch Zement als Füllstoff eingesetzt. Die erstellten Rezepturen zeigten nach 56 Tagen hohe Druckfestigkeiten von über 50 N/mm². Mit zunehmendem Epoxidharzgehalt ergaben sich zwar steigende Biegezugfestigkeiten, jedoch unter Laborlagerung auch größere Längenänderungen. Diese konnten durch den Einsatz eines PCE-Fließmittels, PVA-Kurzfasern und einer optimierten Sieblinie verringert werden. Das Fließmittel verlängerte die Erhärtungszeiten jedoch auf bis zu 1,5 Tage. Zur Ermittlung der Dauerhaftigkeit des Materials wurde es für drei Wochen Temperaturen von -20 bis +60 °C, einer künstlichen Sonnenbestrahlung sowie künstlicher Beregnung ausgesetzt. Im Vergleich zur Laborlagerung ergab sich bei steigendem Epoxidharzanteil ein geringerer Schwund, während die Biegezugfestigkeit der Probeköper nur geringfügig abnahm. Rasterelektronenmikroskopische Untersuchungen zeigten, dass auch bei geringeren Epoxidharzzusätzen Störungen der Zementhydratation auftraten. Weiterhin zeigen sich bei geringen Epoxidharzzusätzen in der Matrix kugelförmige Einschlüsse, die von dispergierten Epoxidharzpartikeln stammen. KW - Bauchemie KW - Mörtel KW - Epoxidharz KW - Dauerhaftigkeit Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211004-45067 SN - 978-3-947197-02-6 PB - Gesellschaft Deutscher Chemiker ER -