TY - CHAP A1 - Hapurne, Tania Mariana T1 - Application of Fuzzy Set Theory in Controlling of Urban Storm Drainage Systems N2 - A fuzzy logic controller - WNC (Water Network Control) was developed for control of urban drainage systems. The objectives are to avoid accidents, flooding, pollutions through combined sewer overflows and excessive operation and maintenance costs. Fuzzy logic was proved to be a promising approach, flexible and easy accepted, because it includes the expert knowledge. Fuzzy control system proposed is robust and also easy to understand and modified. It offers to the operator the possibility to participate directly in the system control, combining the results of the modern optimization techniques with the experience and knowledge accumulated in time by experts. Thus, the control of urban sewer system can be well solved by implementing an intelligent control system, based on available information (fuzzy) and on expert's experience. An important feature of this fuzzy logic system is its capability to elaborate a control decision even in situations that were not considered in the design phase of the urban network. KW - Stadtentwässerung KW - Regenwasser KW - Controlling KW - Fuzzy-Optimierung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5867 ER - TY - CHAP A1 - Halfmann, Ansgar A1 - Rank, Ernst A1 - Glück, M. A1 - Breuer, M. A1 - Durst, F. T1 - A partitioned solution approach for the fluid-structure interaction of wind and thin-walled structures N2 - In many engineering applications two or more different interacting systems require the numer-ical solution of so-called multifield problems. In civil engineering the interaction of fluid and structures plays an important role, i.e. for fabric tensile structures of light and flexible materials often used for large roof systems, capacious umbrellas or canopies. Whereas powerful numerical simulation techniques have been established in structural engineering as well as in fluid mechan-ics, only relatively few approaches to simulate the interaction of fluids with civil engineering constructions have been presented. To determine the wind loads on complex structures, it is still state-of-the-art to apply semi-empirical, strongly simplifying methods or to perform expensive ex-periments in wind tunnels. In this paper an approach of a coupled fluid-structure simulation will be presented for membrane and thin shell structures. The interaction is described by the struc-tural deformation as response to wind forces, resulting in a modification of the fluid flow domain. Besides a realistic determination of the wind loads, information on the structural stability can be obtained. The so-called partitioned solution is based on an iterative frame algorithm, integrating different codes for Computational Fluid Dynamics (CFD) and for Computational Structural Dy-namics (CSD) in an explicit or an implicit time-stepping procedure. All data exchange between the two different applications is performed via a neutral geometric model provided by a coupling interface. A conservative interpolation method is used for the interpolation of the nodal loads. The time-dependent motion of the structure requires a dynamic modification of the different grids and a redefinition of the Navier-Stokes equations in an Arbitrary Langrangian Eulerian (ALE) formulation. As an example for the present implementation, results of a coupled fluid-structure simulation for a textile membrane canopy will be presented. KW - Tragwerk KW - Dünnwandiges Bauelement KW - Windlast KW - Flüssigkeit-Bauwerk-Wechselwirkung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5858 ER - TY - CHAP A1 - Guskov, V. D. A1 - Kabanov, E. N. A1 - Rutman, Y. L. T1 - DEVICE FOR SEISMIC PROTECTION OF BUILDINGS N2 - Seismic insulation is one of the most progressive types of seismic protection. Seismic insulation is understood as applying special devices for reducing of inertial seismic loads acting on a building. The constructions, shown in article, significantly more effectively solve problems of seismic protection, comparing to the existing seismic insulation systems (SIS). The Special Mechanical Engineering Design Office has developed, manufactured and tested a shock-absorber unit (SAU) of large load capacity. The SAU represents a block of number of pneumatic shock-absorbers (PSA), concentrically mounted round the guiding cylinder. The protected object rests upon the upper movable part of the guiding cylinder of the SAU. In its turn, the lower part of the SAU is rested on the foundation plate, mounted on the ground. A set of the SAU is a constructive realization of the SIS. Efficiency of such SIS has been proved as theoretically, so experimentally An effective SIS can also be created on the base of the elasto-plastic shock-absorbers developed by the KBSM. New designing and constructional solutions are based on the use of the original SIS elements, performed on the base of long time existing (in the other field of technical equipment)units, safety and durability of which have been proved by long term service (more than 20 years). KW - Schwingungsdämpfer KW - Erdbebenschutz Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6247 ER - TY - CHAP A1 - Gurtovy, O. G. A1 - Piskunov, V. G. T1 - HIGH-PRECISION MODELING AND FINITE-ELEMENT INVESTIGATION OF ELASTOPLASTIC DEFORMATION OF NON-ISOTROPIC THICK SANDWICH PLATES AND SHELLS N2 - There was suggested a phenomenological modified quadratic condition of the beginning of plasticity for plastic and quasifragile orthotropic materials. Limiting surface in the shape of a paraboloid with an axis bend over hydrostatic axis corresponds to the condition. The equations of theory of current with the isotropic and anisotropic hardenings, associated with the suggested yield condition, modified into the version of determining equations of strain theory of plasticity are received. These defining equations formed the basis of highlyprecise non-classic continual (along thickness) theory of non-linear deformation of thick sandwich plates and sloping shells. In the approximations along the cross coordinate the specificity of flexural and non-flexural deformations is taken into account. The necessity of introducing the approximations of higher order, as well as accounting for the cross compression while decreasing of the relatively cross normal and shear layer rigidness is shown. The specifications, obtained in comparison with the known physically nonlinear specified model of the bending of plates with orthotropic layers are distinguished. An effective procedure of linearization of the solving equations and getting the solutions in frames of the discrete-continual scheme of the finite-element method is suggested. The approximations of higher order let to model the appearance of the cracs of layers being split by the introducing of slightly hard thin layers into the finite element, not violating the idea of continuality of theory. Calculation of a threelayer plate with rigid face diaphragms on the contour is considered KW - Platte KW - Schale KW - Sandwichbauteil KW - Elastoplastizität KW - Finite-Elemente-Methode Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5848 ER - TY - CHAP A1 - Gregotti, Vittorio T1 - Identity and crises of European architecture N2 - Wissenschaftliches Kolloquium vom 14. bis 16. Oktober 1999 in Weimar an der Bauhaus-Universität zum Thema: ‚global village - Perspektiven der Architektur' T3 - Thesis // Bauhaus-Universität - 46.2000,4-5/33-36 KW - Europa KW - Architektur KW - Bauhaus-Kolloquium KW - Weimar KW - 1999 Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-12122 ER - TY - CHAP A1 - Gordienko, Boris I. A1 - Zhak, S. V. T1 - Die optimale Projektierung der metallverarbeitenden Betriebe N2 - Es wird das gemeine Schema der Projektierung, die die Analyse des Marktes einschließt, betrachtet, die Einschätzung der Nomenklatur und des Umfanges des Produktionsausstoßes der Erzeugnisse, und die Schlüsselaufgabe der Wahl der Regimes der Bearbeitung. Die letzte Aufgabe wird - konkretisiert es werden die Formeln berichtet und die Algorithmen der Optimierung nach den Kriterien der Produktivität und den Selbstkostenpreisen. Es sind die Formeln für die Produktivität der Systeme mit der flexiblen Verbindung, präzisiert sowie die Abhängigkeiten für die Standhaftigkeit bei den kleinen Geschwindigkeiten des Schneidens. Die Schlüsselwörter: der Markt, die Regimes der Bearbeitung, die Produktivität, der Selbstkostenpreis, die Optimierung KW - Metall verarbeitende Industrie KW - Produktionsplanung KW - Marketing KW - Optimierung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5832 ER - TY - CHAP A1 - Gartung, Thomas T1 - Bewährte Projektsteuerung für ICE-Neubautrassen – Ingenieuraufgaben an der ICE-Strecke Erfurt – Nürnberg N2 - Um die kompexen Randbedingungen des Eisenbahnbaus erfüllen zu können, hat die Planungsgesellschaft Bahnbau Deutsche Einheit (PBDE) neue Methoden für ein effizientes Management von Planung und Bau eingeführt, die in dem Beitrag vorgestellt werden. KW - Baubetriebslehre KW - Baustelle KW - Management KW - Eisenbahnbau KW - Planung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-7018 ER - TY - CHAP A1 - Garrett, James H. A1 - Sunkpho, J. T1 - Issues in delivering it systems to field users N2 - IT support for field personnel is starting to appear on bridge inspection sites, construction sites, and on the manufacturing floor. ENR magazine now regularly advertises palm computing-based systems for recording data on a construction site. This support can, and should, take on many forms and functions and needs to be carefully designed and evaluated like any other important tool used in the field. With careful design and implementation, IT devices for the field should have tremendous impact on the productivity of field personnel. If the devices are not carefully designed to take account of the field context and the abilities and preferences of the field personnel, field workers will not use these tools. KW - Informationssystem KW - Informationstechnik KW - Transportables Gerät Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5651 ER - TY - CHAP A1 - Frerichs, Uwe T1 - Zukunft des Bauens aus der Sicht eines industriellen Baubetriebs N2 - Im Beitrag werden die Merkmale zukünftigen Bauens dargestellt. Sie beruhen auf drei Kernpunkten: Rationalisierung, Standardisierung und Weiterentwicklung der Technik. Betont wird der hohe Einfluss der Planung auf die Qualität der Bauwerke. KW - Baubetriebslehre KW - Planung KW - Prognose Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-7023 ER - TY - CHAP A1 - Ebert, Matthias A1 - Bucher, Christian T1 - Modelling of changing of dynamic and static parameters of damaged R/C N2 - Dynamic testing for damage assessment as non-destructive method has attracted growing in-terest for systematic inspections and maintenance of civil engineering structures. In this con-text the paper presents the Stochastic Finite Element (SFE) Modeling of the static and dy-namic results of own four point bending experiments with R/C beams. The beams are dam-aged by an increasing load. Between the load levels the dynamic properties are determined. Calculated stiffness loss factors for the displacements and the natural frequencies show differ-ent histories. A FE Model for the beams is developed with a discrete crack formulation. Cor-related random fields are used for structural parameters stiffness and tension strength. The idea is to simulate different crack evolutions. The beams have the same design parameters, but because of the stochastic material properties their undamaged state isn't yet the same. As the structure is loaded a stochastic first crack occurs on the weakest place of the structure. The further crack evolution is also stochastic. These is a great advantage compared with de-terministic formulations. To reduce the computational effort of the Monte Carlo simulation of this nonlinear problem the Latin-Hypercube sampling technique is applied. From the results functions of mean value and standard deviation of displacements and frequencies are calcu-lated. Compared with the experimental results some qualitative phenomena are good de-scribed by the model. Differences occurs especially in the dynamic behavior of the higher load levels. Aim of the investigations is to assess the possibilities of dynamic testing under consideration of effects from stochastic material properties KW - Stahlbetonbauteil KW - Bruchmechanik KW - Dynamische Belastung KW - Statische Last KW - Finite-Elemente-Methode KW - Stochastisches Modell Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5825 ER - TY - CHAP A1 - Duft, Mathias T1 - Zusammenwirken der am Prozess Beteiligten bei komplexen Projekten N2 - Eine integrierte Gesamtplanung, ein konzentriertes Planungs- und Freigabesystem, ein konsequentes Baustellenmanagement sowie die Einbeziehung und Bündelung des Know how und der Leistungsfähigkeit solventer Partner sind Grundlage für die Optimierung der Kommunikations- und Entscheidungswege für die systemgeführte Prozesslenkung. Das wird am Beispiel der Errichtung des Innerstädtischen Einkaufszentrums Anger 1 belegt. KW - Baubetriebslehre KW - Planung KW - Management KW - Baustelle KW - Baustelleneinrichtung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-7035 ER - TY - CHAP A1 - Dudek, Mariusz A1 - Rudnicki, Andrzej A1 - Hempel, Lorenz T1 - Zum Zusammenhang zwischen strukturellen und funktionellen Parametern eines Verkehrsnetzes N2 - Im Vortrag wird der Frage nachgegangen, inwieweit zwischen den strukturellen Parametern Dispersion eines Verkehrsnetzes bzw. der Kennziffer der Unterentwicklung eines Verkehrsnetzes und den mittleren Fahrzeiten bzgl. unterschiedlicher Verkehrsbedarfsmatrizen ein Zusammenhang besteht. An Hand von 10 verschiedenen Ring-Radius-Strukturen für den MIV (Motorisierter Individual-Verkehr) und 3 verschiedenen Ring-Radius-Strukturen für den Busverkehr wird bei 5 unterschiedlichen O-D-Bedarfsmatrizen der Nachweiß eines solchen Zusammenhanges geführt. Die Ergebnisse erlauben es, auf Grund struktureller Analysen Aussagen über funktionelle Bewertungen des Verkehrsnetzes zu treffen. Da strukturelle Bewertungen mit wesentlich geringerem Aufwand an Input-Daten und an Rechenzeit als funktionelle Bewertungen bestimmbar sind, bringt dies deutliche Einsparungen in der Planungsphase von Verkehrsnetzen mit sich. KW - Verkehrsplanung KW - Verkehrsnetz KW - Bedarfsermittlung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5985 ER - TY - CHAP A1 - Ducke, M. A1 - Eckstein, U. A1 - Montag, U. T1 - Die Eisenbahnbrücken des Lehrter Bahnhofs in Berlin - Ein ganzheitliches FE-Berechnungskonzept N2 - Der Komplexität moderner Brückenbauwerke scheinen die verwendeten Berechungsmodelle oft nicht angemessen. Tragwerksberechnungen basieren in vielen Fällen noch auf der Vorgehensweise, das Brückenbauwerk in Einzelbauteile zu zerlegen und mit unterschiedlichen Teilmodellen zu behandeln. Das erscheint, auch vor dem Hintergrund ständig wachsender Rechnerleistung, nicht mehr zeitgemäß. Dies gilt zum Beispiel auch für die gängige Praxis, flächenhafte Brückenüberbauten mit Balkenmodellen zu berechnen. Der vorliegende Beitrag stellt ein ganzheitliches Berech-nungskonzept vor, welches auf der Basis eines einzigen FE-Modells die Berechnung des Gesamtbauwerks erlaubt. Damit wird für alle Bauteile neben der Zustandsgrößenberechnung auch die Bemessung von Stahl- und Spannbetonbauteilen bis hin zu Nachweisen wie zur Beschränkung der Rissbreite geführt. Die Anwendung dieses Berechnungskonzeptes wird am Beispiel der Eisenbahnüberführung des neuen Lehrter Bahn-hofs in Berlin gezeigt. Das verwendete FE-Modell umfasst Baugrund, Fundamente, Stahl- bzw. Gußstahlunterkonstruktion sowie den Stahl- bzw. Spannbetonüberbau. Besonderheiten sind unter anderem die Modellierung des plattenbalkenartigen Überbaus durch exzentrische, vorspannbare Schalenelemente und das getrennte Vorhalten von tragwerks- und lastbezogenen Eingabefiles. Damit gelingt die sequentielle Erfassung unterschiedlicher Bettungsmoduli zur Simulation statischer und dynamischer Beanspruchungen, die Berücksichtigung des Anspannens und der Interaktion zwischen vorgespannten Stahlverbänden zur Aufnahme von Horizontallasten sowie die Berücksichtigung unterschiedlicher statischer Systeme bei der Herstellung des Spannbetonüberbaus. KW - Berlin KW - Eisenbahnbrücke KW - Berechnung KW - Finite-Elemente-Methode KW - Lehrter Bahnhof KW - Gesamtbauwerk Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5812 ER - TY - CHAP A1 - Duarte, Rodrigo T1 - Kulturware und Volkskunst angesichts der "Globalisierung" N2 - Wissenschaftliches Kolloquium vom 14. bis 16. Oktober 1999 in Weimar an der Bauhaus-Universität zum Thema: ‚global village - Perspektiven der Architektur' T3 - Thesis // Bauhaus-Universität - 46.2000,4-5/65-69 KW - Kulturwirtschaft KW - Volkskunst KW - Globalisierung KW - Bauhaus-Kolloquium KW - Weimar KW - 1999 Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-12048 ER - TY - CHAP A1 - Donath, Dirk A1 - Petzold, Frank A1 - Tscherepanow, Ronald A1 - Thurow, Torsten T1 - Geometrieabbildung in der planungsrelevanten Bauaufnahme N2 - Im Rahmen des Sonderforschungsbereiches 524 “Konstruktionen und Werkstoffe für die Revitalisierung von Bauwerken“1 ist das primäre Anliegen des Teilprojektes D2 „Bauplanungsrelevantes digitales Gebäudeaufnahme- und Informationssystem“ die Entwicklung von Methoden und Techniken zur Aufnahme von Bestandsdaten vor Ort oder durch Auswertung vorhandener Dokumentationen und deren direkte Integration in ein Bauwerksmodell [11]. Das Vorhaben erarbeitet Grundlagen zu Aspekten der fachplanerischen Nutzung und der wissenschaftlichen Auswertungen arbeitsmethodischer Vorgehensweisen in der Bestandsaufnahme unter Einbeziehung softwaretechnischer Methoden. Dabei finden Sachverhalte der Strukturierung, die Herausarbeitung von Systematiken der wesentlichen Informations-/Datenmengen, die Ableitung von Methoden zur zerstörungsfreien Erfassung und die Darstellung planungsrelevanter Gebäudeinformationen in digitalen Systemen Berücksichtigung. In diesem Artikel werden ausgehend von Anforderungen der planungsrelevanten architektonischen Bauaufnahme eine Konzeption und die prototypische Realisierung zur flexiblen geometrischen Erfassung – dem Bauaufmaß – vorgestellt. Planungsrelevante Bauaufnahme Die Bauaufnahme dient der Modellbildung durch Erfassung und Wiedergabe eines real existenten Bauwerkes in seinem zum Zeitpunkt der Aufnahme angetroffenen Zustand. Die quasi vollständige Aufnahme ist aufgrund der großen zu ermittelnden Datenmengen und den hierdurch entstehenden Aufwendungen und Kosten nicht möglich [8]. Vielmehr muß eine Auswahl und Abstrahierung der aufzunehmenden Daten, ihrer Repräsentation und die Wahl ihrer Genauigkeit nach den Erfordernissen des jeweiligen Verwendungszweckes der Bauaufnahme erfolgen. So vielfältig die Erfordernisse einer Bauaufnahme ausfallen, so vielfältig sind auch die jeweiligen Forderungen und Auswahlen der aufzunehmenden Daten. In der überwiegenden Mehrheit aller Fälle ist auch die Wiedergabe der vorgefundenen geometrischen Ausprägung des Bauwerkes gewünscht oder erforderlich. Dabei werden unterschiedliche Genauigkeitsanforderungen an verschiedene Bereiche des Bauwerkes gestellt [9] [10]. So reicht vielleicht im Einzelfall eine skizzenhafte Wiedergabe des Umfeldes eines geplanten Ladenbereiches, während die umzunutzenden Bereiche in Ausführungsgenauigkeit zu erfassen sind. Die exakte geometrische Ausprägung eingebauter Bauelemente ist oft nur teilweise bekannt. In der Bauaufnahme muß ein enger Zusammenhang zwischen Geometrie und bauteilorientierter Konstruktion, sowie den verwendeten Ordnungssystemen bestehen. Um diesen Ansprüchen genüge zu tragen, werden entsprechende Aufnahmetechniken, rechnerinterne Abbildungen und Funktionalität zur Interaktion Nutzer - Modell gesucht. KW - Bauplanung KW - Bauaufnahme KW - Bildverarbeitung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6214 ER - TY - CHAP A1 - Donath, Dirk A1 - Liedtke, Maren A1 - Petzold, Frank T1 - Aktuelle Geräte und IT - Unterstützung in der architektonischen Bestandsaufnahme - Grenzen, Möglichkeiten & Visionen N2 - Im Rahmen des Sonderforschungsbereiches 524 ist das primäre Anliegen des Teilprojektes D2 die Entwicklung von Methoden und Techniken zur Aufnahme von Bestandsdaten vor Ort oder durch Auswertung vorhandener Dokumentationen und deren direkte Integration in ein Bauwerksmodell. [15] Das Vorhaben erarbeitet Grundlagen zu Aspekten der fachplanerischen Nutzung und der wissenschaftlichen Auswertungen arbeitsmethodischer Vorgehensweisen in der Bestandsaufnahme unter Einbeziehung softwaretechnischer Methoden. Dabei finden Sachverhalte der Strukturierung, die Herausarbeitung von Systematiken der wesentlichen Informations-/Datenmengen, die Ableitung von Methoden zur zerstörungsfreien Erfassung und die Darstellung planungsrelevanter Gebäudeinformationen in digitalen Systemen Berücksichtigung. Beim Bauaufmaß werden neben traditionellen Methoden und Techniken längst geodätische Verfahren wie die Tachymetrie, die Photogrammetrie und die Handlaserentfernungsmessung einbezogen. In der Praxis des Bestandsaufmaßes repräsentiert gegenwärtig die Tachymetrie, das am häufigsten zur Innen- und Außenaufnahme von Gebäuden eingesetzte geodätische Vermessungsverfahren. [9] [3] Ausgehend von der heutigen Situation in der Bestandsaufnahme wird aufgezeigt, inwieweit es nach dem gegenwärtigen Stand der Technik möglich ist, die in der Geodäsie verwendeten Tachymeter direkt in der Bestandsaufnahme einzusetzen. In einem weiteren Schwerpunkt wird die Konzeption eines rechnergestützten Bauaufnahmesystems basierend auf reflektorlos messenden tachymetrischen Geräten beschrieben. Das Konzept berücksichtigt nicht nur das Bauaufmaß, sondern unterstützt adäquat den gesamten Prozeß der Bauaufnahme – von der Erstbegehung bis hin zur konstruktiven Gliederung. Abschließend werden tendenzielle Möglichkeiten in der Bauaufnahme diskutiert. KW - Bauaufnahme KW - Datenerfassung KW - Dateneingabegerät Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6220 ER - TY - CHAP A1 - De Michelis, Marco T1 - Fin-de-Siècle N2 - Wissenschaftliches Kolloquium vom 14. bis 16. Oktober 1999 in Weimar an der Bauhaus-Universität zum Thema: ‚global village - Perspektiven der Architektur' T3 - Thesis // Bauhaus-Universität - 46.2000,4-5/161-167 KW - Architekturtheorie KW - Bauhaus-Kolloquium KW - Weimar KW - 1999 Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-12016 ER - TY - CHAP A1 - Dannecker, Lutz T1 - Bauschäden im Wohn- und Gewerbebau – eine Thüringer Bestandsaufnahme und Ansätze zur Problemlösung N2 - Der Verfasser gibt einen Überblick über die aktuelle Bauschadensforschung an Wohn-, Gewerbe- und Industriebauten (Schadensanfälligkeit, zeitliche Verteilung von Bauschäden, Verteiliung der Verursachung und des Verschuldens, Schadensintensität in Abhängigkeit von den Vertragsstrukturen, Mängel- und Schadensbeseitigungskosten). Es werden Schlussfolgerungen auf notwendige Maßnahmen zur Reduzierung der Schadensintensität gezogen. KW - Baubetriebslehre KW - Qualität KW - Prozessfähigkeit KW - Bauschaden KW - Wohnungsbau Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-7057 ER - TY - CHAP A1 - Daniunas, A. A1 - Komka, A. A1 - Werner, F. T1 - ANALYSIS AND DETERMINATION OF STRENGTH IN PLASTIC STAGE OF FREE FORM STEEL SHAPES N2 - The steel structure design codes require to check up the member strength when evaluating plastic deformations. The model of perfectly plastic material is accepted. The strength criteria for simple cross-sections (I section, etc.) of steel members are given in design codes. The analytical strength criteria for steel cross-sections and numerical approaches based on stepwise procedure are investigated in many articles. Another way for checking the carrying capacity of cross-sections is the use of methods that are applied for defining strain-deformed state of elastic perfectly plastic systems. In this paper non-iterative methods are suggested for checking strength of cross-sections. Carrying capacity of cross section is verified according to extremum principle of plastic fail under monotonically loading and the strain-deformed state of cross-section is defined according to extremum energy principals of elastic potential of residual stresses and complementary work of residual displacements. The mathematical expressions of these principals for discrete cross-section are formulated as problems of convex mathematical programming. The cross-section of steel member using finite element method is divided into free form plane elements. The constant distribution of stresses along the finite element is accepted. The relationships of finite elements for static formulation of the problem are formed so, that kinematics formulation relationships could be obtained in a formal way using the theory of duality. Numerical examples of determination of cross-section strength, composition of interactive curves and composition of moment-curvature curves for different axial force levels are presented. KW - Stahlkonstruktion KW - Plastische Deformation KW - Mathematisches Modell KW - Finite-Elemente-Methode Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5803 ER - TY - CHAP A1 - Counsell, John T1 - Spatial Database Management and Generation of VRML Models N2 - The cost of keeping large area urban computer aided architectural design (CAAD) models up to date justifies wider use and access. This paper reviews the potential for collaborative groupwork creation and maintenance of such models and suggests an approach to data entry, data management and generation of appropriate levels of detail models from a Geographic Information System (GIS). Staff at the University of the West of England (UWE) modelled a large area of Bristol to demonstrate millennium landmark proposals. It became swiftly apparent that continued amendment of the model to keep it an accurate reflection of changes on the ground was a major data management problem. Piecing in new CAAD models received from Architectural Practices to visualise them in context as part of the planning negotiation process has often taken staff several days of work for each instance. The model is so complex and proprietary that Bristol City operates a specialist visualisation bureau service. UWE later modelled the environs of the Tower of London to support bids for funding and to provide the context for judging the visual impact of iterative design development. Further research continued to develop more effective approaches to. Data conversion and amalgamation from all the diverse sources was the major impediment to effective group working to create the models. It became apparent that a GIS would assist retrieving all the appropriate data that described the part of the model under creation. It was possible to predict that management of many historic part models stepping back through time, allowing for different expert interpretations to co-exist would be in itself a major task requiring a spatial database/GIS. UWE started afresh from the original source data, to explore the collaborative use of GIS and Virtual Reality Modelling Language (VRML) to integrate models and interventions from various sources and to generate an overall navigable interactive whole. Current exploration of the combination of event driven behaviours and Structured Query Language is seeking to define how appropriately to modify objects in the VRML model on demand. This is beginning to realise the potential for use of this process for: asynchronous group modelling on the lines of a collaborative virtual design studio; historic building maintenance management; visitor management; interpretation of historic sites to visitors and public planning information. KW - Raumordnung KW - Visualisierung KW - CAD / Architektur KW - Geographic Information System Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5791 ER - TY - CHAP A1 - Christov, Christo T. A1 - Petrova, Lyllia B. T1 - COMPARISON OF SOME VARIANTS OF THE FINITE STRIP METHOD FOR ANALYSIS OF COMPLEX SHELL STRUCTURES N2 - The subject of this paper is to explore and evaluate the semi-analytical, analytical and numerical versions of the finite strip method (FSM) for static, dynamic and stability analyses of complex thin-walled structures. Many of bridge superstructures, some roof and floor structures, reservoirs, channels, tunnels, subways, layered shells and plates etc. can be analysed by this method. In both semi-analytical and analytical variants beam eigenvalue vibration or stability functions, orthogonal polynomials, products of these functions are used as longitudinal functions of the unknowns. In the numerical FSM spline longitudinal displacement functions are implemented. In the semi-analytical and numerical FSM conventional transverse shape functions for displacements are used. In the analytical FSM the accurate function of the strip normal displacement and the plane stress function are applied. These three basic variants of the FSM are compared in quality and quantity in view to the following: basic ideas, modelling, unknowns, DOF, a kind and order of the strips, longitudinal and transverse displacement and stress functions, compatibility requirements, boundary conditions, ways for obtaining of the strip stiffness and load matrices, a kind and size of the structure stiffness matrix and its band width, mesh density, necessary number of terms in length, accuracy and convergence of the stresses and displacements, approaches for refining results, input and output data, computer resources used, application area, closeness to other methods, options for future development. Numerical example is presented. Advantages and shortcomings are pointed. Conclusions are given. KW - Schale KW - Finite-Streifen-Methode KW - Variantenvergleich Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5760 ER - TY - CHAP A1 - Christov, Christo T. A1 - Petkov, Zdravko B. T1 - DETERMINATION OF THE DYNAMIC STRESS INTENSITY FACTOR USING ADVANCED ENERGY RELEASE EVALUATION N2 - In this study a simple effective procedure practically based upon the FEM for determination of the dynamic stress intensity factor (DSIF) depending on the input frequency and using an advanced strain energy release evaluation by the simultaneous release of a set of fictitious nodal spring links near the crack tip is developed and applied. The DSIF is expressed in terms of the released energy per unit crack length. The formulations of the linear fracture mechanics are accepted. This technique is theoretically based upon the eigenvalue problem for assessment of the spring stiffnesses and on the modal decomposition of the crack shape. The inertial effects are included into the released energy. A linear elastic material, time-dependent loading of sine type and steady state response of the structure are assumed. The procedure allows the opening, sliding and mixed modes of the structure fracture to be studied. This rational and powerful technique requires a mesh refinement near the crack tip. A numerical test example of a square notched steel plate under tension is given. Opening mode of fracture is studied only. The DSIF is calculated using a coarse mesh and a single node release for the released energy computation as well a fine mesh and simultaneous release of four links for more accurate values. The results are analyzed. Comparisons with the known exact results from a static loading are presented. Conclusions are derived. The values of the DSIF are significantly larger than the values of the corresponding static SIF. Significant peaks of the DSIF are observed near the natural frequences. This approach is general, practicable, reliable and versatile. KW - Bruchmechanik KW - Dynamische Belastung KW - Spannungsintensitätsfaktor KW - Eigenwertproblem Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5770 ER - TY - CHAP A1 - Bücker, Joachim T1 - Qualitätssicherung durch baubegleitende Prüfung N2 - Darstellung der aktuellen Situation der Qualitätssicherung im Bauwesen, der Aufgaben und der Vorgehensweise des TÜV Bautechnik bei der Qualitätsüberwachung am Bau. KW - Baubetriebslehre KW - Qualität KW - Prozessfähigkeit Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-7046 ER - TY - CHAP A1 - Burghardt, Michael A1 - Meißner, Udo F. T1 - Dreidimensionale Finite-Element-Baugrundmodelle für Ingeniuerprobleme N2 - Bei komplexen Gründungskonstruktionen sind Planungsfehler durch eine konsistente Modellierung vermeidbar. Manuelle Berechnungsmethoden ermöglichen im allgemeinen ein dreidimensionales Vorgehen nicht. Numerische Berechnungsmethoden, wie z.B. die Finite-Element-Methode, sind ein optimales Werkzeug zur ganzheitlichen Simulation des Problems. Die für die Finite-Element-Analyse notwendige Diskretisierung komplexer Bau- grundstrukturen ist manuell nicht zu bewältigen. Der vorliegende Beitrag zeigt wie ein Finite-Element-Modell automatisch aus einem geotechnischen Modell unter Berücksichtigung der spezifischen Anforderungen der Baugrund-Tragwerk-Struktur und des Bauablaufes erzeugt werden kann. Hierbei wird die Berücksichtigung der geometrischen und der mechanischen Besonderheiten bei der Netzgenerierung dargestellt. KW - Baugrund KW - Mathematisches Modell KW - Dreidimensionales Modell KW - Finite-Elemente-Methode Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5750 ER - TY - CHAP A1 - Bubner, Andre A1 - Thierfelder, Jan T1 - Austausch von planungsrelevanten Daten im Stahlbau N2 - Datenaustausch, Daten resp. Produktdatenmodelle sind seit mehreren Jahren Themen in der Forschung. Verschiedene Forschungsprojekte und Initiativen diverser Firmen führten zu bereichsübergreifenden Ansätzen wie IFC und verschiedenen STEP-AP´s. Speziell im Stahlbau sind die Projekte >Produktschnittstelle Stahlbau< und >CIMsteel< entwickelt, weiterentwickelt und überarbeitet worden. Als Weiterentwicklung der bisher existierenden Austauschformate versuchen neuere Ansätze den Nutzen über die reine Datenübermittlung hinaus zu erweitern. So integrieren diese Lösungsvorschläge Aspekte der Kommunikation, der Zusammenarbeit und des Managements. Des weiteren übernehmen sie Aufgaben der Daten- und Modellverwaltung. Somit erfolgt eine digitale Abbildung unter Einbezug sämtlicher ermittelter Daten. Resultierend aus den besonderen Randbedingungen im Bauwesen, wird ein Bauwerksmodell aus untereinander in Beziehung gesetzten Domänenmodellen aufgebaut KW - Datenaustausch KW - CAD KW - Stahlbau Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6146 ER - TY - CHAP A1 - Boyko, Igor P. A1 - Köppler, H. A1 - Kirichuk, A. T1 - INTERACTION OF SPATIAL THIN-WALLED STRUCTURES WITH FLUID-SATURATED SOIL N2 - Thin-walled spatial structures are broadly used in the modern technician and building. In fuel industry for long-term keeping of oil and gas are used reservoirs of various capacity, which on technological reasons can be shipped under the soil. Shells of reservoirs combine in itself high toughness and low specific consumption of materials. At the same time, being under the soil, they feel steady-state and dynamic loads from ambiance, which particularly in the event, when reservoir is empty, can bring about the loss of stability of its form. On the other hand contact interactions of shell and soil greatly depend on features of ambiance and its saturating of liquid. For building generalized porous springy ambiance models, saturated by the liquid, it is possible to use Bio equations of motion for displacement of hard and fluid phases. Elaboration of mathematical specified interaction models and theirs realization by means of modern computing software allows to study behaviour of spatial thin-walled designs on base of geometric nonlinear theory of shells KW - Raumtragwerk KW - Dünnwandiges Bauelement KW - Boden-Bauwerk-Wechselwirkung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5748 ER - TY - CHAP A1 - Bonev, Z. A1 - Hristov, H. T1 - BEHAVIOR FACTOR EVALUATION BASED ON SDOF SYSTEM PRESENTATION AND ENERGY APPROACH N2 - Rectangular steel frames are considered and subjected to strong ground motion. Their behavior factor is numerically evaluated using nonlinear time history analysis and different ground acceleration records. The behavior factor is determined assuming severe collapse mechanism occurs throughout the time history. The system of equations is transformed into single equation end then the energy balance concept is applied. The expression for the behavior factor is derived and its application to four story two bays steel frame is illustrated and the corresponding results are discussed. KW - Rahmentragwerk KW - Stahlkonstruktion KW - Erdbebenbelastung KW - Bewertung KW - SDOF Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5702 ER - TY - CHAP A1 - Bittrich, Daniel T1 - Verbunddokumente als Nutzeroberfläche von Software für die Tragwerksplanung N2 - Der Schwerpunkt von Forschung und Entwicklung auf dem Gebiet der Tragwerksplanungs-Software lag in den letzten Jahren auf der Erweiterung des funktionalen Umfangs. In der Folge ist es notwendig, den gestiegenen Funktionsumfang einem möglichst breiten Anwenderkreis durch ingenieurgemäß gestaltete Arbeitsumgebungen zugänglich zu machen, so dass ein möglichst effizientes und fehlerarmes Arbeiten ermöglicht wird. Aus der Sicht der Tragwerksplaner muss eine ingenieurgemäß gestaltete Software eine dem spezifischen Arbeitsablauf angepasste Nutzer-Software-Interaktion aufweisen. Dabei sind die benötigten Funktionalitäten in ein einheitliches System zu integrieren und eine Anpassbarkeit durch den Anwender sicherzustellen. Die Berücksichtigung dieser Anforderungen mit herkömmlichen Mitteln würde einen unverhältnismäßig hohen Entwicklungsaufwand erfordern. Infolgedessen muss aus der Sicht der Software-Entwickler eine moderne Software-Architektur für die Tragwerksplanung eine Erhöhung des Wiederverwendungsgrades und eine unabhängige Erweiterbarkeit als zusätzliche Anforderungen erfüllen. In diesem Beitrag wird ein auf Verbunddokumenten basierendes Konzept vorgestellt, mit dem eine Zusammenführung von Standard-Software und fachspezifischen Software-Komponenten zu einer ingenieurgemäßen Arbeitsumgebung ermöglicht wird. Damit kann die Analyse und die Dokumentation eines Tragelementes einschließlich der zugehörigen Datenhaltung innerhalb eines Verbunddokumentes erfolgen. Gleichzeitig kann der software-technische Wiederverwendungsgrad durch die Definition eines Component Frameworks als unabhängig erweiterbare Software-Architektur und durch den Einsatz von Software-Komponenten mit eigener Nutzeroberfläche über das bisher erreichte Niveau hinaus gesteigert werden. Die Umsetzbarkeit des Konzeptes wird durch eine Pilotimplementierung demonstriert. KW - Tragwerk KW - Baustatik KW - CAE KW - Softwareengineering Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5739 ER - TY - CHAP A1 - Biehounek, Josef A1 - Grolik, Helmut T1 - Zur voll-probabilistischen Verallgemeinerung des Kraftgrößenverfahrens N2 - Die Versagenswahrscheinlichkeit nach einem Grenzzustand wird gewöhnlich mit dem Integral I der Basisvariablen-Verteilungsdichte über den Versagensbereich bestimmt. Dabei ist eine geschlossene Lösung nur im Spezialfall normalverteilter Basisvariablen bei Linearität der Grenzzustandsgleichung möglich. In anderen Fällen sind verschiedene Näherungsverfahren gebräuchlich, die auf den Momenten der Basisvariablen und geeignet gewählten Indizes als Sicherheitskenngrößen beruhen. Eine größere Genauigkeit bieten die Zuverlässigkeitstheorien erster bzw. zweiter Ordnung, die ebenfalls von I ausgehen. Im Beitrag wird ein neuartiges Verfahren vorgestellt, dessen Ausgangspunkt nicht I, sondern das Kraftgrößenverfahren als einem Standardalgorithmus des konstruktiven Ingenieurbaus ist. Die Einbeziehung der maßgebenden Zufallsgrößen in die Matrix der Vorzahlen und die Belastungszahlen führt zur Verallgemeinerung des Systems der Elastizitätsgleichungen zum zufälligen System der Elastizitätsgleichungen. Dessen Lösung, die durch den Übergang zu einem deterministischen Ersatzsystem gewonnen wird, liefert die statisch Unbestimmten als Funktionen der im System wirkenden Zufallsgrößen (z.B. E-Modul der Stäbe und Belastung). Da dieser Zusammenhang analytisch vorliegt, kann die Wirkung einzelner Zufallseinflüsse auf die statisch Unbestimmten und die daraus folgenden sicherheitsrelevanten Zustandsgrößen beurteilt werden. Die Dichtefunktion der Grenzzustandsgleichung kann berechnet oder durch Simulation ermittelt werden. Daraus folgt . Nicht normalverteilte Zufallsgrößen werden durch Entwicklung in orthogonale Polynome Gaußscher Zufallsgrößen berücksichtigt. KW - Kraftmethode KW - Versagen KW - Wahrscheinlichkeitsrechnung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5728 ER - TY - CHAP A1 - Bargstädt, Hans-Joachim T1 - Vorwort und Begrüßung zum Tag des Baubetriebs 2000 N2 - Richtung baubetrieblicher Forschung, Überblick über das Tagungsprogramm KW - Begrüßung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6980 ER - TY - CHAP A1 - Althöfer, Ingo T1 - Multiple Choice Systems for Decision Support N2 - Humans are able to think, to feel, and to sense. We are also able to compute but not very well. In contrast, computers are giants in computing. Yet, they can not do anything else besides computing. Appropriate combinations of the different gifts and strengths of human and computer may result in impressive performances. In the 3-Hirn approach one human and two computers are involved. On the computers different programs are running. The human starts the machines and inspects the solutions they propose. He compares these candidate solutions and finally decides for one of the alternatives. So, the human makes the final choice from a small number of computer proposals. In performance-oriented chess, 3-Hirn combinations consisting of an amateur player and commer-cial software have reached world class level. 3-Hirn is a Decision Support System with Multiple Choice Structure. Such Multiple Choice Systems will be exhibited and discussed. KW - Entscheidung bei mehrfacher Zielsetzung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5685 ER - TY - CHAP A1 - Abramian, A. K. A1 - Litvin, S.S. T1 - AUTOPARAMETRIC STABILIZER OF OSCILLATION AMPLITUDE N2 - A method of automatic maintenance of vibration amplitude of a number of mechanisms at given level, when exiting force amplitude is varied greatly is given. For this purpose a pendulum is attached to a mechanism through a viscoelastic hinge. Load of a pendulum can move along an arm and it is viscoelastic connected to it. KW - Schwingung KW - Amplitude KW - Stabilisierung KW - Automatisiertes System KW - Viskoelastisches Gelenk Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5674 ER - TY - CHAP ED - Professur Baubetrieb und Bauverfahren, T1 - Tag des Baubetriebs 2000 : Tagungsbeiträge "Prozesssteuerung - Projektleitung - Dienstleistung" N2 - Beiträge zum Tag des Baubetriebs „Prozesssteuerung - Projektleitung - Dienstleistung“ am Freitag, dem 7. Juli 2000 in Weimar aus Anlass des 45-jährigen Bestehens der Professur für Baubetrieb und Bauverfahren an der Bauhaus-Universität Weimar T3 - Schriften der Professur Baubetrieb und Bauverfahren - 02 KW - Weimar / Bauhaus-Universität / Professur Baubetrieb und Bauverfahren KW - Prozesssteuerung KW - Dienstleistung Y1 - 2000 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20081111-14433 SN - 3-86068-142-7 ER -