TY - JOUR A1 - Mehling, Simon A1 - Schnabel, Tobias A1 - Londong, Jörg T1 - Photocatalytic ozonation in an immersion rotary body reactor for the removal of micro-pollutants from the effluent of wastewater treatment plants JF - Water Science & Technology N2 - Carrier-bound titanium dioxide catalysts were used in a photocatalytic ozonation reactor for the degradation of micro-pollutants in real wastewater. A photocatalytic immersion rotary body reactor with a 36-cm disk diameter was used, and was irradiated using UV-A light-emitting diodes. The rotating disks were covered with catalysts based on stainless steel grids coated with titanium dioxide. The dosing of ozone was carried out through the liquid phase via an external enrichment and a supply system transverse to the flow direction. The influence of irradiation power and ozone dose on the degradation rate for photocatalytic ozonation was investigated. In addition, the performance of the individual processes photocatalysis and ozonation were studied. The degradation kinetics of the parent compounds were determined using liquid chromatography tandem mass spectrometry. First-order kinetics were determined for photocatalysis and photocatalytic ozonation. A maximum reaction rate of the reactor was determined, which could be achieved by both photocatalysis and photocatalytic ozonation. At a dosage of 0.4 mg /mg DOC, the maximum reaction rate could be achieved using 75% of the irradiation power used for sole photocatalysis, allowing increases in the energetic efficiency of photocatalytic wastewater treatment processes. The process of photocatalytic ozonation is suitable to remove a wide spectrum of micro-pollutants from wastewater. KW - Abwasserreinigung KW - Fotokatalyse KW - Mikroverunreinigungen KW - anthropogenic micro-pollutants KW - photocatalysis KW - photocatalytic ozonation KW - wastewater treatment KW - titan dioxide Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220209-45865 UR - https://iwaponline.com/wst/article/85/1/535/85800/Photocatalytic-ozonation-in-an-immersion-rotary VL - 2022 IS - volume 85, issue 1 SP - 535 EP - 548 PB - IWA Publishing CY - London ER - TY - JOUR A1 - Harirchian, Ehsan A1 - Kumari, Vandana A1 - Jadhav, Kirti A1 - Rasulzade, Shahla A1 - Lahmer, Tom A1 - Raj Das, Rohan T1 - A Synthesized Study Based on Machine Learning Approaches for Rapid Classifying Earthquake Damage Grades to RC Buildings JF - Applied Sciences N2 - A vast number of existing buildings were constructed before the development and enforcement of seismic design codes, which run into the risk of being severely damaged under the action of seismic excitations. This poses not only a threat to the life of people but also affects the socio-economic stability in the affected area. Therefore, it is necessary to assess such buildings’ present vulnerability to make an educated decision regarding risk mitigation by seismic strengthening techniques such as retrofitting. However, it is economically and timely manner not feasible to inspect, repair, and augment every old building on an urban scale. As a result, a reliable rapid screening methods, namely Rapid Visual Screening (RVS), have garnered increasing interest among researchers and decision-makers alike. In this study, the effectiveness of five different Machine Learning (ML) techniques in vulnerability prediction applications have been investigated. The damage data of four different earthquakes from Ecuador, Haiti, Nepal, and South Korea, have been utilized to train and test the developed models. Eight performance modifiers have been implemented as variables with a supervised ML. The investigations on this paper illustrate that the assessed vulnerability classes by ML techniques were very close to the actual damage levels observed in the buildings. KW - Maschinelles Lernen KW - Neuronales Netz KW - Machine learning KW - Building safety assessment KW - artificial neural networks KW - supervised learning KW - damaged buildings KW - rapid classification KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210818-44853 UR - https://www.mdpi.com/2076-3417/11/16/7540 VL - 2021 IS - Volume 11, issue 16, article 7540 SP - 1 EP - 33 PB - MDPI CY - Basel ER - TY - JOUR A1 - Legatiuk, Dmitrii T1 - Mathematical Modelling by Help of Category Theory: Models and Relations between Them JF - mathematics N2 - The growing complexity of modern practical problems puts high demand on mathematical modelling. Given that various models can be used for modelling one physical phenomenon, the role of model comparison and model choice is becoming particularly important. Methods for model comparison and model choice typically used in practical applications nowadays are computationbased, and thus time consuming and computationally costly. Therefore, it is necessary to develop other approaches to working abstractly, i.e., without computations, with mathematical models. An abstract description of mathematical models can be achieved by the help of abstract mathematics, implying formalisation of models and relations between them. In this paper, a category theory-based approach to mathematical modelling is proposed. In this way, mathematical models are formalised in the language of categories, relations between the models are formally defined and several practically relevant properties are introduced on the level of categories. Finally, an illustrative example is presented, underlying how the category-theory based approach can be used in practice. Further, all constructions presented in this paper are also discussed from a modelling point of view by making explicit the link to concrete modelling scenarios. KW - Kategorientheorie KW - Modellierung KW - Modellierungsmethode KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210817-44844 UR - https://www.mdpi.com/2227-7390/9/16/1946?type=check_update&version=1 VL - 2021 IS - volume 9, issue 16, article 1946 PB - MDPI CY - Basel ER - TY - JOUR A1 - Ren, Huilong A1 - Zhuang, Xiaoying A1 - Oterkus, Erkan A1 - Zhu, Hehua A1 - Rabczuk, Timon T1 - Nonlocal strong forms of thin plate, gradient elasticity, magneto-electro-elasticity and phase-field fracture by nonlocal operator method JF - Engineering with Computers N2 - The derivation of nonlocal strong forms for many physical problems remains cumbersome in traditional methods. In this paper, we apply the variational principle/weighted residual method based on nonlocal operator method for the derivation of nonlocal forms for elasticity, thin plate, gradient elasticity, electro-magneto-elasticity and phase-field fracture method. The nonlocal governing equations are expressed as an integral form on support and dual-support. The first example shows that the nonlocal elasticity has the same form as dual-horizon non-ordinary state-based peridynamics. The derivation is simple and general and it can convert efficiently many local physical models into their corresponding nonlocal forms. In addition, a criterion based on the instability of the nonlocal gradient is proposed for the fracture modelling in linear elasticity. Several numerical examples are presented to validate nonlocal elasticity and the nonlocal thin plate. KW - Bruchmechanik KW - Elastizität KW - Peridynamik KW - energy form KW - weak form KW - peridynamics KW - variational principle KW - explicit time integration Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211207-45388 UR - https://link.springer.com/article/10.1007/s00366-021-01502-8 VL - 2021 SP - 1 EP - 22 ER - TY - JOUR A1 - Alsaad, Hayder A1 - Völker, Conrad T1 - Qualitative evaluation of the flow supplied by personalized ventilation using schlieren imaging and thermography JF - Building and Environment N2 - Personalized ventilation (PV) is a mean of delivering conditioned outdoor air into the breathing zone of the occupants. This study aims to qualitatively investigate the personalized flows using two methods of visualization: (1) schlieren imaging using a large schlieren mirror and (2) thermography using an infrared camera. While the schlieren imaging was used to render the velocity and mass transport of the supplied flow, thermography was implemented to visualize the air temperature distribution induced by the PV. Both studies were conducted using a thermal manikin to simulate an occupant facing a PV outlet. As a reference, the flow supplied by an axial fan and a cased axial fan was visualized with the schlieren system as well and compared to the flow supplied by PV. Schlieren visualization results indicate that the steady, low-turbulence flow supplied by PV was able to penetrate the thermal convective boundary layer encasing the manikin's body, providing clean air for inhalation. Contrarily, the axial fan diffused the supplied air over a large target area with high turbulence intensity; it only disturbed the convective boundary layer rather than destroying it. The cased fan supplied a flow with a reduced target area which allowed supplying more air into the breathing zone compared to the fan. The results of thermography visualization showed that the supplied cool air from PV penetrated the corona-shaped thermal boundary layer. Furthermore, the supplied air cooled the surface temperature of the face, which indicates the large impact of PV on local thermal sensation and comfort. KW - Bildverarbeitung KW - Photothermische Methode KW - Visualisierung KW - Belüftung KW - Lüftungsanlage KW - Schlieren imaging KW - Thermography KW - Visualization KW - Personalized ventilation KW - Axial fan Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211008-45117 UR - https://www.sciencedirect.com/science/article/abs/pii/S0360132319306602?via%3Dihub N1 - This is the accepted manuscript of the article published by Elsevier in Building and Environment 167 (2020) 106450, which can be found at https://doi.org/10.1016/j.buildenv.2019.106450. VL - 2020 IS - Volume 167, article 106450 PB - Elsevier CY - New York ER - TY - JOUR A1 - Alkam, Feras A1 - Lahmer, Tom T1 - A robust method of the status monitoring of catenary poles installed along high-speed electrified train tracks JF - Results in Engineering N2 - Electric trains are considered one of the most eco-friendly and safest means of transportation. Catenary poles are used worldwide to support overhead power lines for electric trains. The performance of the catenary poles has an extensive influence on the integrity of the train systems and, consequently, the connected human services. It became a must nowadays to develop SHM systems that provide the instantaneous status of catenary poles in- service, making the decision-making processes to keep or repair the damaged poles more feasible. This study develops a data-driven, model-free approach for status monitoring of cantilever structures, focusing on pre-stressed, spun-cast ultrahigh-strength concrete catenary poles installed along high-speed train tracks. The pro-posed approach evaluates multiple damage features in an unfied damage index, which leads to straightforward interpretation and comparison of the output. Besides, it distinguishes between multiple damage scenarios of the poles, either the ones caused by material degradation of the concrete or by the cracks that can be propagated during the life span of the given structure. Moreover, using a logistic function to classify the integrity of structure avoids the expensive learning step in the existing damage detection approaches, namely, using the modern machine and deep learning methods. The findings of this study look very promising when applied to other types of cantilever structures, such as the poles that support the power transmission lines, antenna masts, chimneys, and wind turbines. KW - Fahrleitung KW - Catenary poles KW - SHM KW - Model-free status monitoring KW - Sigmoid function KW - High-speed electric train KW - Schaden KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211011-45212 UR - https://www.sciencedirect.com/science/article/pii/S2590123021000906?via%3Dihub VL - 2021 IS - volume 12, article 100289 SP - 1 EP - 8 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Schwerzmann, Katia T1 - Abolish! Against the Use of Risk Assessment Algorithms at Sentencing in the US Criminal Justice System JF - Philosophy & Technology N2 - In this article, I show why it is necessary to abolish the use of predictive algorithms in the US criminal justice system at sentencing. After presenting the functioning of these algorithms in their context of emergence, I offer three arguments to demonstrate why their abolition is imperative. First, I show that sentencing based on predictive algorithms induces a process of rewriting the temporality of the judged individual, flattening their life into a present inescapably doomed by its past. Second, I demonstrate that recursive processes, comprising predictive algorithms and the decisions based on their predictions, systematically suppress outliers and progressively transform reality to match predictions. In my third and final argument, I show that decisions made on the basis of predictive algorithms actively perform a biopolitical understanding of justice as management and modulation of risks. In such a framework, justice becomes a means to maintain a perverse social homeostasis that systematically exposes disenfranchised Black and Brown populations to risk. KW - Biopolitik KW - Soziale Gerechtigkeit KW - Algorithmus KW - predictive algorithms KW - cybernetics KW - criminal justice KW - social justice KW - biopolitics Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211207-45417 UR - https://link.springer.com/article/10.1007/s13347-021-00491-2 VL - 2021 SP - 1 EP - 22 ER - TY - JOUR A1 - Müller, Matthias A1 - Ludwig, Horst-Michael A1 - Tange Hasholt, Marianne T1 - Salt frost attack on concrete: the combined effect of cryogenic suction and chloride binding on ice formation JF - Materials and Structures N2 - Scaling of concrete due to salt frost attack is an important durability issue in moderate and cold climates. The actual damage mechanism is still not completely understood. Two recent damage theories—the glue spall theory and the cryogenic suction theory—offer plausible, but conflicting explanations for the salt frost scaling mechanism. The present study deals with the cryogenic suction theory, which assumes that freezing concrete can take up unfrozen brine from a partly frozen deicing solution during salt frost attack. According to the model hypothesis, the resulting saturation of the concrete surface layer intensifies the ice formation in this layer and causes salt frost scaling. In this study an experimental technique was developed that makes it possible to quantify to which extent brine uptake can increase ice formation in hardened cement paste (used as a model material for concrete). The experiments were carried out with low temperature differential scanning calorimetry, where specimens were subjected to freeze–thaw cycles while being in contact with NaCl brine. Results showed that the ice content in the specimens increased with subsequent freeze–thaw cycles due to the brine uptake at temperatures below 0 °C. The ability of the hardened cement paste to bind chlorides from the absorbed brine at the same time affected the freezing/melting behavior of the pore solution and the magnitude of the ice content. KW - Beton KW - Frost KW - Beton KW - Frostangriff KW - salt frost attack KW - cryogenic suction KW - chloride binding Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211207-45392 UR - https://link.springer.com/article/10.1617/s11527-021-01779-7 VL - 2021 IS - issue 54, article 189 SP - 1 EP - 16 ER - TY - JOUR A1 - Schmitz, Tonia A1 - Kraft, Eckhard T1 - Pilot scale photobioreactor system for land-based macroalgae cultivation JF - Journal of Applied Phycology N2 - Marine macroalgae such as Ulva intestinalis have promising properties as feedstock for cosmetics and pharmaceuticals. However, since the quantity and quality of naturally grown algae vary widely, their exploitability is reduced – especially for producers in high-priced markets. Moreover, the expansion of marine or shore-based cultivation systems is unlikely in Europe, since promising sites either lie in fishing zones, recreational areas, or natural reserves. The aim was therefore to develop a closed photobioreactor system enabling full control of abiotic environmental parameters and an effective reconditioning of the cultivation medium in order to produce marine macroalgae at sites distant from the shore. To assess the feasibility and functionality of the chosen technological concept, a prototypal plant has been implemented in central Germany – a site distant from the sea. Using a newly developed, submersible LED light source, cultivation experiments with Ulva intestinalis led to growth rates of 7.72 ± 0.04 % day−1 in a cultivation cycle of 28 days. Based on the space demand of the production system, this results in fresh mass productivity of 3.0 kg m−2, respectively, of 1.1 kg m−2 per year. Also considering the ratio of biomass to energy input amounting to 2.76 g kWh−1, significant future improvements of the developed photobioreactor system should include the optimization of growth parameters, and the reduction of the system’s overall energy demand. KW - Makroalgen KW - Photobioreaktor KW - macro algae KW - photobioreactor KW - ulva intestinalis KW - LED light source Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211207-45401 UR - https://link.springer.com/article/10.1007/s10811-021-02617-7 VL - 2021 SP - 1 EP - 10 ER - TY - JOUR A1 - Londong, Jörg A1 - Barth, Marcus A1 - Söbke, Heinrich T1 - Modeling and Simulation of Source Separation in Sanitation Systems for Reducing Emissions of Antimicrobial Resistances JF - Water N2 - Antimicrobial resistance (AMR) is identified by the World Health Organization (WHO) as one of the top ten threats to public health worldwide. In addition to public health, AMR also poses a major threat to food security and economic development. Current sanitation systems contribute to the emergence and spread of AMR and lack effective AMR mitigation measures. This study assesses source separation of blackwater as a mitigation measure against AMR. A source-separation-modified combined sanitation system with separate collection of blackwater and graywater is conceptually described. Measures taken at the source, such as the separate collection and discharge of material flows, were not considered so far on a load balance basis, i.e., they have not yet been evaluated for their effectiveness. The sanitation system described is compared with a combined system and a separate system regarding AMR emissions by means of simulation. AMR is represented in the simulation model by one proxy parameter each for antibiotics (sulfamethoxa-zole), antibiotic-resistant bacteria (extended-spectrum beta-lactamase E. Coli), and antibiotic re-sistance genes (blaTEM). The simulation results suggest that the source-separation-based sanitation system reduces emissions of antibiotic-resistant bacteria and antibiotic resistance genes into the aquatic environment by more than six logarithm steps compared to combined systems. Sulfa-methoxazole emissions can be reduced by 75.5% by keeping blackwater separate from graywater and treating it sufficiently. In summary, sanitation systems incorporating source separation are, to date, among the most effective means of preventing the emission of AMR into the aquatic envi-ronment. KW - Abwasser KW - Ressourcen KW - microbial resistances KW - antimicrobial resistance genes KW - source separation KW - resource-oriented sanitation KW - UASB KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211202-45338 UR - www.mdpi.com/2073-4441/13/23/3342 VL - 2021 IS - Volume 13, issue 23, article 3342 SP - 1 EP - 19 PB - MDPI CY - Basel ER - TY - JOUR A1 - Kraus, Matthias A1 - Klaus, Martin A1 - Wittor, Björn T1 - Experimental Analyses on the Resistance of Tapped Blind Holes JF - ce/papers N2 - Bolted connections are commonly used in steel construction. The load-bearing behavior of bolt fittings has extensively been studied in various research activities and the bearing capacity of bolted connections can be assessed well by standard regulations for practical applications. With regard to tensile loading, the nut does not have strong influence on resistances, since the failure occurs in the bolts due to higher material strengths of the nuts. In some applications, so-called “blind holes” are used to connect plated components. In a manner of speaking, the nut is replaced by the “outer” plate with a prefabricated hole and thread, in which the bolt can be screwed and tightened. In such connections, the limit load capacity cannot solely be assessed by the bolt resistance, since the threaded hole in the base material has strong influence on the structural behavior. In this context, the available screw-in depth of the blind hole is of fundamental importance. The German National Annex of EN 1993-1-8 provides information on a necessary depth in order to transfer the full tensile capacity of the bolt. However, some connections do not allow to fabricate such depths. In these cases, the capacity of the connection is unclear and not specified. In this paper, first experiments on corresponding connections with different screw-in depths are presented and compared to limit load capacities according to the standard. KW - Gewinde KW - Bolzen KW - threat KW - bolt KW - tapped blind holes Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220112-45553 UR - https://onlinelibrary.wiley.com/doi/10.1002/cepa.1273 VL - 2021 IS - Volume 4, issue 2-4 SP - 141 EP - 147 PB - Ernst & Sohn, a Wiley brand CY - Berlin ER - TY - JOUR A1 - Alsaad, Hayder A1 - Hartmann, Maria A1 - Voelker, Conrad T1 - The effect of a living wall system designated for greywater treatment on the hygrothermal performance of the facade JF - Energy and Buildings N2 - Besides their multiple known benefits regarding urban microclimate, living walls can be used as decentralized stand-alone systems to treat greywater locally at the buildings. While this offers numerous environmental advantages, it can have a considerable impact on the hygrothermal performance of the facade as such systems involve bringing large quantities of water onto the facade. As it is difficult to represent complex entities such as plants in the typical simulation tools used for heat and moisture transport, this study suggests a new approach to tackle this challenge by coupling two tools: ENVI-Met and Delphin. ENVI-Met was used to simulate the impact of the plants to determine the local environmental parameters at the living wall. Delphin, on the other hand, was used to conduct the hygrothermal simulations using the local parameters calculated by ENVI-Met. Four wall constructions were investigated in this study: an uninsulated brick wall, a precast concrete plate, a sandy limestone wall, and a double-shell wall. The results showed that the living wall improved the U-value, the exterior surface temperature, and the heat flux through the wall. Moreover, the living wall did not increase the risk of moisture in the wall during winter and eliminated the risk of condensation. KW - Feuchteleitung KW - Diffusionswärme KW - Heat transport KW - Moisture transport KW - Living wall KW - Delphin KW - ENVI-Met Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20240116-65299 UR - https://www.sciencedirect.com/science/article/pii/S0378778821009956 VL - 2022 IS - volume 255, article 111711 ER - TY - JOUR A1 - Vakkari, Pertti A1 - Völske, Michael A1 - Potthast, Martin A1 - Hagen, Matthias A1 - Stein, Benno T1 - Predicting essay quality from search and writing behavior JF - Journal of Association for Information Science and Technology N2 - Few studies have investigated how search behavior affects complex writing tasks. We analyze a dataset of 150 long essays whose authors searched the ClueWeb09 corpus for source material, while all querying, clicking, and writing activity was meticulously recorded. We model the effect of search and writing behavior on essay quality using path analysis. Since the boil-down and build-up writing strategies identified in previous research have been found to affect search behavior, we model each writing strategy separately. Our analysis shows that the search process contributes significantly to essay quality through both direct and mediated effects, while the author's writing strategy moderates this relationship. Our models explain 25–35% of the variation in essay quality through rather simple search and writing process characteristics alone, a fact that has implications on how search engines could personalize result pages for writing tasks. Authors' writing strategies and associated searching patterns differ, producing differences in essay quality. In a nutshell: essay quality improves if search and writing strategies harmonize—build-up writers benefit from focused, in-depth querying, while boil-down writers fare better with a broader and shallower querying strategy. KW - Information Retrieval KW - Textproduktion KW - Suchverfahren KW - Aufsatz KW - Suchverhalten KW - Pfadanalyse KW - Suchmaschine Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210804-44692 UR - https://asistdl.onlinelibrary.wiley.com/doi/10.1002/asi.24451 VL - 2021 IS - volume 72, issue 7 SP - 839 EP - 852 PB - Wiley CY - Hoboken, NJ ER - TY - JOUR A1 - Legatiuk, Dmitrii A1 - Weisz-Patrault, Daniel T1 - Coupling of Complex Function Theory and Finite Element Method for Crack Propagation Through Energetic Formulation: Conformal Mapping Approach and Reduction to a Riemann–Hilbert Problem JF - Computational Methods and Function Theory N2 - In this paper we present a theoretical background for a coupled analytical–numerical approach to model a crack propagation process in two-dimensional bounded domains. The goal of the coupled analytical–numerical approach is to obtain the correct solution behaviour near the crack tip by help of the analytical solution constructed by using tools of complex function theory and couple it continuously with the finite element solution in the region far from the singularity. In this way, crack propagation could be modelled without using remeshing. Possible directions of crack growth can be calculated through the minimization of the total energy composed of the potential energy and the dissipated energy based on the energy release rate. Within this setting, an analytical solution of a mixed boundary value problem based on complex analysis and conformal mapping techniques is presented in a circular region containing an arbitrary crack path. More precisely, the linear elastic problem is transformed into a Riemann–Hilbert problem in the unit disk for holomorphic functions. Utilising advantages of the analytical solution in the region near the crack tip, the total energy could be evaluated within short computation times for various crack kink angles and lengths leading to a potentially efficient way of computing the minimization procedure. To this end, the paper presents a general strategy of the new coupled approach for crack propagation modelling. Additionally, we also discuss obstacles in the way of practical realisation of this strategy. KW - Angewandte Mathematik KW - Finite-Elemente-Methode KW - Rissausbreitung KW - Modellierung KW - Bruchmechanik KW - fracture mechanics KW - crack propagation KW - coupling KW - energetic approach Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210805-44763 UR - https://link.springer.com/article/10.1007/s40315-021-00403-7 VL - 2021 SP - 1 EP - 23 PB - Springer CY - Heidelberg ER - TY - JOUR A1 - Noori, Hamidreza A1 - Mortazavi, Bohayra A1 - Keshtkari, Leila A1 - Zhuang, Xiaoying A1 - Rabczuk, Timon T1 - Nanopore creation in MoS2 and graphene monolayers by nanoparticles impact: a reactive molecular dynamics study JF - Applied Physics A N2 - In this work, extensive reactive molecular dynamics simulations are conducted to analyze the nanopore creation by nano-particles impact over single-layer molybdenum disulfide (MoS2) with 1T and 2H phases. We also compare the results with graphene monolayer. In our simulations, nanosheets are exposed to a spherical rigid carbon projectile with high initial velocities ranging from 2 to 23 km/s. Results for three different structures are compared to examine the most critical factors in the perforation and resistance force during the impact. To analyze the perforation and impact resistance, kinetic energy and displacement time history of the projectile as well as perforation resistance force of the projectile are investigated. Interestingly, although the elasticity module and tensile strength of the graphene are by almost five times higher than those of MoS2, the results demonstrate that 1T and 2H-MoS2 phases are more resistive to the impact loading and perforation than graphene. For the MoS2nanosheets, we realize that the 2H phase is more resistant to impact loading than the 1T counterpart. Our reactive molecular dynamics results highlight that in addition to the strength and toughness, atomic structure is another crucial factor that can contribute substantially to impact resistance of 2D materials. The obtained results can be useful to guide the experimental setups for the nanopore creation in MoS2or other 2D lattices. KW - Nanomechanik KW - Molekülstruktur KW - Nanoporöser Stoff KW - MoS2 KW - molecular dynamics KW - Nanopore KW - Graphene Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210804-44756 UR - https://link.springer.com/article/10.1007/s00339-021-04693-5 VL - 2021 IS - volume 127, article 541 SP - 1 EP - 13 PB - Springer CY - Heidelberg ER - TY - JOUR A1 - Seichter, Cosima Zita A1 - Neßler, Miriam A1 - Knopf, Paul T1 - Der Refugee District in Belgrad. Ein Raum der Nicht-Bewegung zwischen neoliberaler Stadtentwicklung, serbischem Migrationsmanagement und EU-Grenzregime JF - sub\urban. Zeitschrift für Kritische Stadtforschung N2 - Durch internationale Fluchtbewegungen über die sogenannte Balkanroute bildete sich in Serbiens Hauptstadt Belgrad in den letzten Jahren ein sogenannter Refugee District heraus. Im Kontext von Migration und Flucht werden dabei zahlreiche Spannungsfelder auf unterschiedlichen räumlichen und politischen Ebenen sichtbar. Für Flüchtende kreieren diese eine Situation, die von Stillstand, Ausweglosigkeit, Kontrolle, Gefahr und Verdrängung geprägt ist. Allerdings führen die Vielschichtigkeit und die Diversität unterschiedlicher Akteur*innen, die bezüglich der Situation von Flüchtenden auf der Balkanroute wirkmächtig sind, auch zu Nischen, Widerständigkeiten und der Möglichkeit (neuer) Allianzen. Auf diese Weise entsteht eine kollektive Praktik der Nicht-Bewegung im Widerstand gegen die Unterdrückung und für globale Bewegungsfreiheit. KW - Belgrad KW - Europäische Union KW - Flüchtling KW - Flüchtlingspolitik KW - Balkanroute KW - Grenzregime KW - refugee district KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210805-44776 UR - https://zeitschrift-suburban.de/sys/index.php/suburban/article/view/622 VL - 2021 IS - Band 9, Heft 1/2 SP - 225 EP - 234 PB - sub\urban e.V. CY - Berlin ER - TY - JOUR A1 - Kraus, Matthias A1 - Crişan, Nicolae-Andrei A1 - Wittor, Björn T1 - Stability Study of Cantilever-Beams – Numerical Analysis and Analytical Calculation (LTB) JF - ce/papers N2 - According to Eurocode, the computation of bending strength for steel cantilever beams is a straightforward process. The approach is based on an Ayrton-Perry formula adaptation of buckling curves for steel members in compression, which involves the computation of an elastic critical buckling load for considering the instability. NCCI documents offer a simplified formula to determine the critical bending moment for cantilevers beams with symmetric cross-section. Besides the NCCI recommendations, other approaches, e.g. research literature or Finite-Element-Analysis, may be employed to determine critical buckling loads. However, in certain cases they render different results. Present paper summarizes and compares the abovementioned analytical and numerical approaches for determining critical loads and it exemplarily analyses corresponding cantilever beam capacities using numerical approaches based on plastic zones theory (GMNIA). KW - Träger KW - Stahl KW - Biegefestigkeit KW - Finite-Elemente-Methode KW - Stahlträger KW - Knicklast KW - Freiträgerkapazität KW - Eurocode Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220112-45637 UR - https://onlinelibrary.wiley.com/doi/full/10.1002/cepa.1539 VL - 2021 IS - Volume 4, issue 2-4 SP - 2199 EP - 2206 PB - Ernst & Sohn, a Wiley brand CY - Berlin ER - TY - JOUR A1 - Becher, Lia A1 - Gena, Amayu Wakoya A1 - Alsaad, Hayder A1 - Richter, Bernhard A1 - Spahn, Claudia A1 - Völker, Conrad T1 - The spread of breathing air from wind instruments and singers using schlieren techniques JF - Indoor Air N2 - The spread of breathing air when playing wind instruments and singing was investigated and visualized using two methods: (1) schlieren imaging with a schlieren mirror and (2) background-oriented schlieren (BOS). These methods visualize airflow by visualizing density gradients in transparent media. The playing of professional woodwind and brass instrument players, as well as professional classical trained singers were investigated to estimate the spread distances of the breathing air. For a better comparison and consistent measurement series, a single high note, a single low note, and an extract of a musical piece were investigated. Additionally, anemometry was used to determine the velocity of the spreading breathing air and the extent to which it was quantifiable. The results showed that the ejected airflow from the examined instruments and singers did not exceed a spreading range of 1.2 m into the room. However, differences in the various instruments have to be considered to assess properly the spread of the breathing air. The findings discussed below help to estimate the risk of cross-infection for wind instrument players and singers and to develop efficacious safety precautions, which is essential during critical health periods such as the current COVID-19 pandemic. KW - Covid-19 KW - Pandemie KW - Blasinstrument KW - Gesang KW - Schlierenmethode KW - airborne infection KW - background-oriented schlieren KW - schlieren imaging Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220209-45817 UR - https://onlinelibrary.wiley.com/doi/full/10.1111/ina.12869 VL - 2021 IS - volume 31, issue 6 SP - 1798 EP - 1814 PB - Wiley Blackwell CY - Oxford ER - TY - JOUR A1 - Legatiuk, Anastasiia A1 - Gürlebeck, Klaus A1 - Hommel, Angela T1 - Estimates for the discrete fundamental solution of the discrete Laplace operator on a rectangular lattice JF - Mathematical Methods in the Applied Sciences N2 - This paper presents numerical analysis of the discrete fundamental solution of the discrete Laplace operator on a rectangular lattice. Additionally, to provide estimates in interior and exterior domains, two different regularisations of the discrete fundamental solution are considered. Estimates for the absolute difference and lp-estimates are constructed for both regularisations. Thus, this work extends the classical results in the discrete potential theory to the case of a rectangular lattice and serves as a basis for future convergence analysis of the method of discrete potentials on rectangular lattices. KW - diskrete Fourier-Transformation KW - Laplace-Operator KW - discrete fourier transform KW - discrete fundamental solution KW - laplace operator KW - rectangular lattice Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220209-45829 UR - https://onlinelibrary.wiley.com/doi/full/10.1002/mma.7747 VL - 2021 SP - 1 EP - 23 PB - Wiley CY - Chichester ER - TY - JOUR A1 - Ibanez, Stalin A1 - Kraus, Matthias T1 - A Numerical Approach for Plastic Cross Cross-Sectional Analyses of Steel Members JF - ce/papers N2 - Global structural analyses in civil engineering are usually performed considering linear-elastic material behavior. However, for steel structures, a certain degree of plasticization depending on the member classification may be considered. Corresponding plastic analyses taking material nonlinearities into account are effectively realized using numerical methods. Frequently applied finite elements of two and three-dimensional models evaluate the plasticity at defined nodes using a yield surface, i.e. by a yield condition, hardening rule, and flow rule. Corresponding calculations are connected to a large numerical as well as time-consuming effort and they do not rely on the theoretical background of beam theory, to which the regulations of standards mainly correspond. For that reason, methods using beam elements (one-dimensional) combined with cross-sectional analyses are commonly applied for steel members in terms of plastic zones theories. In these approaches, plasticization is in general assessed by means of axial stress only. In this paper, more precise numerical representation of the combined stress states, i.e. axial and shear stresses, is presented and results of the proposed approach are validated and discussed. KW - Stahlkonstruktion KW - Plastizität KW - Strukturanalyse KW - Stahlbauteil KW - Axialspannung KW - Finite-Elemente-Methode Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220112-45622 UR - https://onlinelibrary.wiley.com/doi/full/10.1002/cepa.1527 VL - 2021 IS - Volume 4, issue 2-4 SP - 2098 EP - 2106 PB - Ernst & Sohn, a Wiley brand CY - Berlin ER - TY - JOUR A1 - Meiabadi, Mohammad Saleh A1 - Moradi, Mahmoud A1 - Karamimoghadam, Mojtaba A1 - Ardabili, Sina A1 - Bodaghi, Mahdi A1 - Shokri, Manouchehr A1 - Mosavi, Amir Hosein T1 - Modeling the Producibility of 3D Printing in Polylactic Acid Using Artificial Neural Networks and Fused Filament Fabrication JF - polymers N2 - Polylactic acid (PLA) is a highly applicable material that is used in 3D printers due to some significant features such as its deformation property and affordable cost. For improvement of the end-use quality, it is of significant importance to enhance the quality of fused filament fabrication (FFF)-printed objects in PLA. The purpose of this investigation was to boost toughness and to reduce the production cost of the FFF-printed tensile test samples with the desired part thickness. To remove the need for numerous and idle printing samples, the response surface method (RSM) was used. Statistical analysis was performed to deal with this concern by considering extruder temperature (ET), infill percentage (IP), and layer thickness (LT) as controlled factors. The artificial intelligence method of artificial neural network (ANN) and ANN-genetic algorithm (ANN-GA) were further developed to estimate the toughness, part thickness, and production-cost-dependent variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid machine learning (ML) technique could enhance the accuracy of modeling by about 7.5, 11.5, and 4.5% for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. On the other hand, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which enables the usability of printed PLA objects. KW - 3D-Druck KW - Polymere KW - Maschinelles Lernen KW - 3D printing KW - machine learning KW - fused filament fabrication KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220110-45518 UR - https://www.mdpi.com/2073-4360/13/19/3219 VL - 2021 IS - Volume 13, issue 19, article 3219 SP - 1 EP - 21 PB - MDPI CY - Basel ER - TY - JOUR A1 - Jiang, Mingze A1 - Rößler, Christiane A1 - Wellmann, Eva A1 - Klaver, Jop A1 - Kleiner, Florian A1 - Schmatz, Joyce T1 - Workflow for high-resolution phase segmentation of cement clinker fromcombined BSE image and EDX spectral data JF - Journal of Microscopy N2 - Burning of clinker is the most influencing step of cement quality during the production process. Appropriate characterisation for quality control and decision-making is therefore the critical point to maintain a stable production but also for the development of alternative cements. Scanning electron microscopy (SEM) in combination with energy dispersive X-ray spectroscopy (EDX) delivers spatially resolved phase and chemical information for cement clinker. This data can be used to quantify phase fractions and chemical composition of identified phases. The contribution aims to provide an overview of phase fraction quantification by semi-automatic phase segmentation using high-resolution backscattered electron (BSE) images and lower-resolved EDX element maps. Therefore, a tool for image analysis was developed that uses state-of-the-art algorithms for pixel-wise image segmentation and labelling in combination with a decision tree that allows searching for specific clinker phases. Results show that this tool can be applied to segment sub-micron scale clinker phases and to get a quantification of all phase fractions. In addition, statistical evaluation of the data is implemented within the tool to reveal whether the imaged area is representative for all clinker phases. KW - Zementklinker KW - Bildsegmentierung KW - Rasterelektronenmikroskopie KW - cement clinker KW - image segmentation KW - EDX KW - superpixel Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211215-45449 UR - https://onlinelibrary.wiley.com/doi/epdf/10.1111/jmi.13072 VL - 2021 SP - 1 EP - 7 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Kleiner, Florian A1 - Rößler, Christiane A1 - Vogt, Franziska A1 - Osburg, Andrea A1 - Ludwig, Horst-Michael T1 - Reconstruction of calcium silicate hydrates using multiple 2D and 3D imaging techniques: Light microscopy, μ-CT, SEM, FIB-nT combined with EDX JF - Journal of Microscopy N2 - This study demonstrates the application and combination of multiple imaging techniques [light microscopy, micro-X-ray computer tomography (μ-CT), scanning electron microscopy (SEM) and focussed ion beam – nano-tomography (FIB-nT)] to the analysis of the microstructure of hydrated alite across multiple scales. However, by comparing findings with mercury intrusion porosimetry (MIP), it becomes obvious that the imaged 3D volumes and 2D images do not sufficiently overlap at certain scales to allow a continuous quantification of the pore size distribution (PSD). This can be overcome by improving the resolution and increasing the measured volume. Furthermore, results show that the fibrous morphology of calcium-silicate-hydrates (C-S-H) phases is preserved during FIB-nT. This is a requirement for characterisation of nano-scale porosity. Finally, it was proven that the combination of FIB-nT with energy-dispersive X-ray spectroscopy (EDX) data facilitates the phase segmentation of a 11 × 11 × 7.7 μm3 volume of hydrated alite. KW - Zementklinker KW - Bildsegmentierung KW - Rasterelektronenmikroskopie KW - Computertomographie KW - tomography KW - focussed ion beam KW - cement microstructure KW - micro-CT Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220106-45458 UR - https://onlinelibrary.wiley.com/doi/10.1111/jmi.13081 VL - 2021 SP - 1 EP - 6 PB - John Wiley & Sons Ltd CY - Oxford ER - TY - JOUR A1 - Anic, Filip A1 - Penava, Davorin A1 - Sarhosis, Vasilis A1 - Abrahamczyk, Lars T1 - Development and Calibration of a 3D Micromodel for Evaluation of Masonry Infilled RC Frame Structural Vulnerability to Earthquakes JF - Geosciences N2 - Within the scope of literature, the influence of openings within the infill walls that are bounded by a reinforced concrete frame and excited by seismic drift forces in both in- and out-of-plane direction is still uncharted. Therefore, a 3D micromodel was developed and calibrated thereafter, to gain more insight in the topic. The micromodels were calibrated against their equivalent physical test specimens of in-plane, out-of-plane drift driven tests on frames with and without infill walls and openings, as well as out-of-plane bend test of masonry walls. Micromodels were rectified based on their behavior and damage states. As a result of the calibration process, it was found that micromodels were sensitive and insensitive to various parameters, regarding the model’s behavior and computational stability. It was found that, even within the same material model, some parameters had more effects when attributed to concrete rather than on masonry. Generally, the in-plane behavior of infilled frames was found to be largely governed by the interface material model. The out-of-plane masonry wall simulations were governed by the tensile strength of both the interface and masonry material model. Yet, the out-of-plane drift driven test was governed by the concrete material properties. KW - Verwundbarkeit KW - Ausfachung KW - Stahlbeton KW - RC frames KW - unreinforced masonry infill walls KW - openings KW - structural vulnerability KW - out-of-plane seismic load KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211202-45370 UR - https://www.mdpi.com/2076-3263/11/11/468 VL - 2021 IS - Voume 11, issue 11, article 468 PB - MDPI CY - Basel ER - TY - JOUR A1 - Schmidt, Albrecht A1 - Lahmer, Tom T1 - Efficient domain decomposition based reliability analysis for polymorphic uncertain material parameters JF - Proceedings in Applied Mathematics & Mechanics N2 - Realistic uncertainty description incorporating aleatoric and epistemic uncertainties can be described within the framework of polymorphic uncertainty, which is computationally demanding. Utilizing a domain decomposition approach for random field based uncertainty models the proposed level-based sampling method can reduce these computational costs significantly and shows good agreement with a standard sampling technique. While 2-level configurations tend to get unstable with decreasing sampling density 3-level setups show encouraging results for the investigated reliability analysis of a structural unit square. KW - Polymorphie KW - Stoffeigenschaft KW - Stochastik KW - polymorphe Unschärfemodellierung KW - Materialverhalten KW - hybride Werkstoffe Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220112-45563 UR - https://onlinelibrary.wiley.com/doi/full/10.1002/pamm.202100014 VL - 2021 IS - Volume 21, issue 1 SP - 1 EP - 4 PB - Wiley-VHC CY - Weinheim ER - TY - JOUR A1 - Wenzel, Mirjam T1 - Das partikulare Gedächtnis jüdischer Museen N2 - Bauhaus-Gastprofessorin Mirjam Wenzel referierte am 30. Juni 2021 im Audimax der Bauhaus-Universität Weimar zur Entstehungsgeschichte und Konzeption Jüdischer Museen. Dabei ging sie darauf ein, inwiefern diese Museen besonders relevant für aktuelle gesellschaftliche und politische Fragestellungen sind. Prof. Wenzels zweiter öffentlicher Vortrag an der Bauhaus-Universität Weimar skizzierte die Potentiale von Kultureinrichtungen in Zeiten gesellschaftspolitischer Veränderungen im Allgemeinen und die Bedeutung Jüdischer Museen angesichts verbaler und tätlicher Gewalt gegen Jüdinnen und Juden im Besonderen. T3 - Neue Bauhausvorträge - 7 KW - Gedächtnis Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20211129-45355 UR - https://www.uni-weimar.de/de/universitaet/profil/mensch-macht-moderne/juedische-museen/ ER - TY - JOUR A1 - Wiegmann, Matti A1 - Kersten, Jens A1 - Senaratne, Hansi A1 - Potthast, Martin A1 - Klan, Friederike A1 - Stein, Benno T1 - Opportunities and risks of disaster data from social media: a systematic review of incident information JF - Natural Hazards and Earth System Sciences N2 - Compiling and disseminating information about incidents and disasters are key to disaster management and relief. But due to inherent limitations of the acquisition process, the required information is often incomplete or missing altogether. To fill these gaps, citizen observations spread through social media are widely considered to be a promising source of relevant information, and many studies propose new methods to tap this resource. Yet, the overarching question of whether and under which circumstances social media can supply relevant information (both qualitatively and quantitatively) still remains unanswered. To shed some light on this question, we review 37 disaster and incident databases covering 27 incident types, compile a unified overview of the contained data and their collection processes, and identify the missing or incomplete information. The resulting data collection reveals six major use cases for social media analysis in incident data collection: (1) impact assessment and verification of model predictions, (2) narrative generation, (3) recruiting citizen volunteers, (4) supporting weakly institutionalized areas, (5) narrowing surveillance areas, and (6) reporting triggers for periodical surveillance. Furthermore, we discuss the benefits and shortcomings of using social media data for closing information gaps related to incidents and disasters. KW - Katastrophe KW - Social Media KW - Datenbank KW - Information KW - Katastrophenmanagement KW - Soziale Medien KW - Datensammlung Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210804-44634 UR - https://nhess.copernicus.org/articles/21/1431/2021/nhess-21-1431-2021.html VL - 2021 IS - Volume 21, Issue 5 SP - 1431 EP - 1444 PB - European Geophysical Society CY - Katlenburg-Lindau ER - TY - JOUR A1 - Kleiner, Florian T1 - Optimization and semi-automatic evaluation of a frosting process for a soda lime silicate glass based on phosphoric acid JF - International Journal of Applied Glass Science N2 - Chemical glass frosting processes are widely used to create visual attractive glass surfaces. A commonly used frosting bath mainly contains ammonium bifluoride (NH4HF2) mixed with hydrochloric acid (HCl). The frosting process consists of several baths. Firstly, the preliminary bath to clean the object. Secondly, the frosting bath which etches the rough light scattering structure into the glass surface. Finally, the washing baths to clean the frosted object. This is where the constituents of the preceding steps accumulate and have to be filtered from the sewage. In the present contribution, phosphoric acid (H3PO4) was used as a substitute for HCl to reduce the amount of ammonium (NH4+) and chloride (Cl−) dissolved in the waste water. In combination with magnesium carbonate (MgCO3), it allows the precipitation of ammonium within the sewage as ammonium magnesium phosphate (MgNH4PO4). However, a trivial replacement of HCl by H3PO4 within the frosting process causes extensive frosting errors, such as inhomogeneous size distributions of the structures or domains that are not fully covered by these structures. By modifying the preliminary bath composition, it was possible to improve the frosting result considerably. To determine the optimal composition of the preliminary bath, a semi-automatic evaluation method has been developed. This method renders the objective comparison of the resulting surface quality possible. KW - Silicatglas KW - Mattieren KW - Ätzen KW - automated quality control KW - etching KW - glass frosting KW - phosphoric acid Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210701-44548 UR - https://ceramics.onlinelibrary.wiley.com/doi/10.1111/ijag.15866 SP - 1 EP - 8 PB - John Wiley & Sons ER - TY - JOUR A1 - Buschow, Christopher A1 - Possler, Daniel A1 - Scheper, Jule T1 - Teaching Media Entrepreneurship: How A Start-up Simulation Can Increase Students’ Knowledge and Encourage Them to Work in Entrepreneurial Contexts JF - Teaching Journalism and Mass Communication N2 - Entrepreneurship and start-up activities are seen as a key response to recent upheavals in the media industry: Newly founded ventures can act as important drivers for industry transformation and renewal, pioneering new products, business models, and organizational designs (e.g. Achtenhagen, 2017; Buschow & Laugemann, 2020). In principle, media students represent a crucial population of nascent entrepreneurs: individuals who will likely become founders of start-ups (Casero-Ripollés et al., 2016). However, their willingness to start a new business is generally considered to be rather low (Goyanes, 2015), and for journalism students, the idea of innovation tends to be conservative, following traditional norms and professional standards (Singer & Broersma, 2020). In a sample of Spanish journalism students, López-Meri et al. (2020) found that one of the main barriers to entrepreneurial intentions is that students feel they lack knowledge and training in entrepreneurship. In the last 10 years, a wide variety of entrepreneurship education courses have been set up in media departments of colleges and universities worldwide. These programs have been designed to sensitize and prepare communications, media and journalism students to think and act entrepreneurially (e.g. Caplan et al., 2020; Ferrier, 2013; Ferrier & Mays, 2017; Hunter & Nel, 2011). Entrepreneurial competencies and practices not only play a crucial role for start-ups, but, in imes of digital transformation, are increasingly sought after by legacy media companies as well (Küng, 2015). At the Department of Journalism and Communication Research, Hanover University of Music, Drama and Media, Germany, we have been addressing these developments with the “Media Entrepreneurship” program. The course, established in 2013, aims to provide fundamental knowledge of entrepreneurship, as well as promoting students‘ entrepreneurial thinking and behavior. This article presents the pedagogical approach of the program and investigates learning outcomes. By outlining and evaluating the Media Entrepreneurship program, this article aims to promote good practices of entrepreneurship education in communications, media and journalism, and to reflect on the limitations of such programs. KW - Medienwirtschaft KW - Entrepreneurship KW - Journalismus KW - Studium KW - Medienwissenschaft KW - Start-up-Simulation Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210729-44628 UR - https://aejmc.us/wp-content/uploads/sites/9/2021/07/TJMC-11.1-Buschow-et-al.pdf VL - 2021 IS - Volume 11, Nr. 1 SP - 65 EP - 69 PB - Small Programs Interest Group ER - TY - JOUR A1 - Cappachione, Clotilde A1 - Partschefeld, Stephan A1 - Osburg, Andrea A1 - Gliubizzi, Rocco A1 - Gaeta, Carmine T1 - Modified Carboxymethylcellulose-Based Scaffolds as New Potential Ecofriendly Superplasticizers with a Retardant Effect for Mortar: From the Synthesis to the Application JF - Materials N2 - This article is focused on the research and development of new cellulose ether derivatives as innovative superplasticizers for mortar systems. Several synthetic strategies have been pursued to obtain new compounds to study their properties on cementitious systems as new bio-based additives. The new water-soluble admixtures were synthesized using a complex carboxymethylcellulose-based backbone that was first hydrolyzed and then sulfo-ethylated in the presence of sodium vinyl sulphonate. Starting with a complex biopolymer that is widely known as a thickening agent was very challenging. Only by varying the hydrolysis times and temperatures of the reactions was achieved the aimed goal. The obtained derivatives showed different molecular weight (Mw) and anionic charges on their backbones. An improvement in shear stress and dynamic viscosity values of CEM II 42.5R cement was observed with the samples obtained with a longer time of higher temperature hydrolysis and sulfo-ethylation. Investigations into the chemical nature of the pore solution, calorimetric studies and adsorption experiments clearly showed the ability of carboxymethyl cellulose superplasticizer (CMC SP) to interact with cement grains and influence hydration processes within a 48-h time window, causing a delay in hydration reactions in the samples. The fluidity of the cementitious matrices was ascertained through slump test and preliminary studies of mechanical and flexural strength of the hardened mortar formulated with the new ecological additives yielded values in terms of mechanical properties. Finally, the computed tomography (CT) images completed the investigation of the pore network structure of hardened specimens, highlighting their promising structure porosity. KW - Mörtel KW - Verflüssigung KW - superplasticizers KW - carboxymethylcellulose KW - mortar KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210804-44689 UR - https://www.mdpi.com/1996-1944/14/13/3569 VL - 2021 IS - volume 14, issue 13, article 3569 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Staubach, Patrick A1 - Machacek, Jan A1 - Skowronek, Josefine A1 - Wichtmann, Torsten T1 - Vibratory pile driving in water-saturated sand: Back-analysis of model tests using a hydro-mechanically coupled CEL method JF - Soils and Foundations N2 - The development of a hydro-mechanically coupled Coupled-Eulerian–Lagrangian (CEL) method and its application to the back-analysisof vibratory pile driving model tests in water-saturated sand is presented. The predicted pile penetration using this approachis in good agreement with the results of the model tests as well as with fully Lagrangian simulations. In terms of pore water pressure, however, the results of the CEL simulation show a slightly worse accordance with the model tests compared to the Lagrangian simulation. Some shortcomings of the hydro-mechanically coupled CEL method in case of frictional contact problems and pore fluids with high bulk modulus are discussed. Lastly, the CEL method is applied to the simulation of vibratory driving of open-profile piles under partially drained conditions to study installation-induced changes in the soil state. It is concluded that the proposed method is capable of realistically reproducing the most important mechanisms in the soil during the driving process despite its addressed shortcomings. KW - Plastische Deformation KW - Vibratory pile driving KW - Coupled-Eulerian–Lagrangian KW - Hydro-mechanically coupled KW - Hypoplasticity KW - Relative acceleration KW - Large deformation KW - Deformationsverhalten KW - Plastizität KW - OA-Publikationsfonds2020 Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210203-43571 UR - https://www.sciencedirect.com/science/article/pii/S0038080620337586?via%3Dihub VL - 2021 IS - Volume 61, Issue 1 SP - 144 EP - 159 PB - Elsevier, Science Direct CY - Amsterdam ER - TY - JOUR A1 - Lashkar-Ara, Babak A1 - Kalantari, Niloofar A1 - Sheikh Khozani, Zohreh A1 - Mosavi, Amir T1 - Assessing Machine Learning versus a Mathematical Model to Estimate the Transverse Shear Stress Distribution in a Rectangular Channel JF - Mathematics N2 - One of the most important subjects of hydraulic engineering is the reliable estimation of the transverse distribution in the rectangular channel of bed and wall shear stresses. This study makes use of the Tsallis entropy, genetic programming (GP) and adaptive neuro-fuzzy inference system (ANFIS) methods to assess the shear stress distribution (SSD) in the rectangular channel. To evaluate the results of the Tsallis entropy, GP and ANFIS models, laboratory observations were used in which shear stress was measured using an optimized Preston tube. This is then used to measure the SSD in various aspect ratios in the rectangular channel. To investigate the shear stress percentage, 10 data series with a total of 112 different data for were used. The results of the sensitivity analysis show that the most influential parameter for the SSD in smooth rectangular channel is the dimensionless parameter B/H, Where the transverse coordinate is B, and the flow depth is H. With the parameters (b/B), (B/H) for the bed and (z/H), (B/H) for the wall as inputs, the modeling of the GP was better than the other one. Based on the analysis, it can be concluded that the use of GP and ANFIS algorithms is more effective in estimating shear stress in smooth rectangular channels than the Tsallis entropy-based equations. KW - Maschinelles Lernen KW - smooth rectangular channel KW - Tsallis entropy KW - genetic programming KW - artificial intelligence KW - machine learning KW - big data KW - computational hydraulics Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210504-44197 UR - https://www.mdpi.com/2227-7390/9/6/596 VL - 2021 IS - Volume 9, Issue 6, Article 596 PB - MDPI CY - Basel ER - TY - JOUR A1 - Alkam, Feras A1 - Lahmer, Tom T1 - Eigenfrequency-Based Bayesian Approach for Damage Identification in Catenary Poles JF - Infrastructures N2 - This study proposes an efficient Bayesian, frequency-based damage identification approach to identify damages in cantilever structures with an acceptable error rate, even at high noise levels. The catenary poles of electric high-speed train systems were selected as a realistic case study to cover the objectives of this study. Compared to other frequency-based damage detection approaches described in the literature, the proposed approach is efficiently able to detect damages in cantilever structures to higher levels of damage detection, namely identifying both the damage location and severity using a low-cost structural health monitoring (SHM) system with a limited number of sensors; for example, accelerometers. The integration of Bayesian inference, as a stochastic framework, in the proposed approach, makes it possible to utilize the benefit of data fusion in merging the informative data from multiple damage features, which increases the quality and accuracy of the results. The findings provide the decision-maker with the information required to manage the maintenance, repair, or replacement procedures. KW - Fahrleitung KW - Schaden KW - Fahrleitungsmast KW - Schadenserkennung KW - vibration-based damage identification KW - Bayesian inference Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210510-44256 UR - https://www.mdpi.com/2412-3811/6/4/57 VL - 2021 IS - Volume 6, issue 4, article 57 SP - 1 EP - 19 PB - MDPI CY - Basel ER - TY - JOUR A1 - Ehlers, Jan A1 - Grimmer, Janine A1 - Strack, Veronika A1 - Huckauf, Anke T1 - The influence of sham feedback on physiological processing during fear-driven stimulation JF - PLOS ONE N2 - Biofeedback constitutes a well-established, non-invasive method to voluntary interfere in emotional processing by means of cognitive strategies. However, treatment durations exhibit strong inter-individual variations and first successes can often be achieved only after a large number of sessions. Sham feedback constitutes a rather untapped approach by providing feedback that does not correspond to the participant’s actual state. The current study aims to gain insights into mechanisms of sham feedback processing in order to support new techniques in biofeedback therapy. We carried out two experiments and applied different types of sham feedback on skin conductance responses and pupil size changes during affective processing. Results indicate that standardized but context-sensitive sham signals based on skin conductance responses exert a stronger influence on emotional regulation compared to individual sham feedback from ongoing pupil dynamics. Also, sham feedback should forego unnatural signal behavior to avoid irritation and skepticism among participants. Altogether, a reasonable combination of stimulus features and sham feedback characteristics enables to considerably reduce the actual bodily responsiveness already within a single session. KW - Biofeedback KW - Biofeedback KW - Sham Feedback KW - Affective Processing KW - OA-Publikationsfonds2021 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210510-44249 UR - https://journals.plos.org/plosone/article?id=10.1371/journal.pone.0251211 IS - Volume 16, issue 5, article e0251211 SP - 1 EP - 17 PB - PLOS CY - San Francisco, Calif. ER -