TY - THES A1 - Grosse, Marco T1 - Zur numerischen Simulation des physikalisch nichtlinearen Kurzzeittragverhaltens von Nadelholz am Beispiel von Holz-Beton-Verbundkonstruktionen T1 - On the numerical simulation of the nonlinear short-time carrying behaviour of softwood with application to timber-concrete composite structures N2 - In der Arbeit wird ein räumliches Materialmodell für den anisotropen Werkstoff Holz vorgestellt. Dessen Leistungsfähigkeit wird durch Verifikationsrechnungen und die Simulation eigener Versuche aufgezeigt. In diesen Versuchen wurde das Tragverhalten spezieller Schubverbindungselemente der Brettstapel-Beton-Verbundbauweise untersucht. Die Kombination eines Brettstapels mit einer schubfest angeschlossenen Betonplatte ist eine vorteilhafte Möglichkeit, Schnittholz mit geringem Querschnitt effektiv in biegebeanspruchten Bauteilen einzusetzen. Es werden die Ergebnisse der experimentellen Untersuchungen zu den Schubverbindungselementen Flachstahlschloss und Nutverbindung vorgestellt. Diese zeichnen sich durch eine über die gesamte Plattenbreite kontinuierliche Übertragung der Schubkraft per Kontaktpressung aus. Vor allem in Brettstapel-Beton-Verbunddecken werden somit ein sehr hoher Verschiebungsmodul sowie eine eminente Tragfähigkeit erreicht. Um mit numerischen Strukturanalysen die in den Versuchen beobachteten Versagensmechanismen adäquat abbilden und realistische Prognosen für das Tragverhalten von Bauteilen oder Verbindungen treffen zu können, muss das physikalisch nichtlineare Verhalten aller beteiligter Baustoffe in die Berechnungen einbezogen werden. Im Rahmen der Dissertation wurde ein auf der Plastizitätstheorie basierendes Materialmodell für Nadelholz hergeleitet und in das FE-Programm ANSYS implementiert, welches die Mikrostruktur des Holzes als verschmierendes Ersatzkontinuum erfasst. Anhand des anatomischen Aufbaus des inhomogenen, anisotropen und porigen Werkstoffs werden die holzspezifischen Versagensmechanismen und die daraus abgeleiteten konstitutiven Beziehungen erläutert. Das ausgeprägt anisotrope Tragverhalten von Holz ist vor allem durch erstaunliche Duktilität bei Stauchung, sprödes Versagen bei Zug- und Schubbeanspruchung und enorme Festigkeitsunterschiede in den Wuchsrichtungen gekennzeichnet. Die Auswirkungen der größtenteils unabhängig voneinander auftretenden, mikromechanischen Versagensmechanismen auf die Spannungs-Verformungsbeziehungen wurden durch die Formulierung adäquater Ver- resp. Entfestigungsfunktionen in Abhängigkeit der Beanspruchungsmodi erfasst. Das dem Materialmodell zu Grunde liegende mehrflächige Fließkriterium berücksichtigt die Interaktion aller sechs Komponenten des räumlichen Spannungszustandes. Die durchgeführten Verifikations- und Simulationsberechnungen belegen, dass der erarbeitete Ansatz sowohl zur Bewertung des Tragvermögens als auch zur Beurteilung von Riss- bzw. Schädigungsursachen von Holzbauteilen eingesetzt werden kann. Die numerische Simulation eröffnet neue, bisher wenig beachtete Möglichkeiten zur Untersuchung komplexer Holzstrukturen sowie Anschlussdetails und wird sich auf Grund der Aussagekraft und Flexibilität auch im Ingenieurholzbau mehr und mehr gegenüber ausschließlich experimenteller Untersuchung durchsetzen. N2 - In the dissertation a spatial model for the anisotropic, porous material wood is presented. The efficiency of this numerical approach is pointed out by verifying computations and simulations of own experiments. In these tests the load carrying behaviour of special joining techniques for laminated timber concrete composite constructions have been examined. The combination of a laminated timber element with a shear resistant joined concrete slab is a profitable alternative for effectively using lumber with small cross section in bending stressed members. The results of the experimental investigations of flat-steel-lock and notch connection are presented. These are characterised by a load transmission via contact pressure continuously over the entire slab width. Particularly in laminated timber concrete composite ceilings a very stiff load-deflection relationship as well as an eminent load-carrying capacity is reached. To simulate the structural behaviour of members and to model there failure mechanisms it is necessary to take the mechanically nonlinear behaviour in the critical and post critical range of all involved materials into account. For this reason a constitutive material model for timber based on the plasticity theory was implemented in the finite element code ANSYS. The basic multisurface yield criterion considers the interaction of all six components of the spatial stress state. The proposal is furthermore based on the classic continuum mechanics. Therefore, a crack is not described discretely, but by its effect on the stress deformation behaviour. The numerical model reproduces the wood-specific anisotropic, load dependent strengths as well as predominantly independent proceeding of strain hardening and, respectively, softening. The conducted verifications and simulations prove, that the designed approach can be applied to the evaluation of the load-carrying behaviour as well as crack and damage causes of timber components. The numerical simulation opens new potentialities for investigation of complex wooden structures as well as connection details. Compared with expensive experimental studies this procedure will gain more significance due to its expressiveness and flexibility even in timber engineering. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 7 KW - Holzbau KW - Verbundbauweise KW - Beton KW - Nichtlineare Finite-Elemente-Methode KW - Plastizitätstheorie KW - Numerische Mathematik KW - Simulation KW - Nichtlineare Kon KW - Holz-Beton-Verbund KW - HBV KW - Versagensmechanismen KW - Brettstapel KW - timber concrete composite KW - laminated timber Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20060215-7725 ER - TY - THES A1 - Heidolf, Thorsten T1 - Zeit- und beanspruchungsabhängiges Tragverhalten von polymermodifiziertem Beton unter mehrfach wiederholter Beanspruchung T1 - Time- and Strain-Dependent Behaviour of Polymer-Modified Concrete with Multifariously Repeated Load N2 - In der vorliegenden Arbeit werden die experimentellen Ergebnisse eigener Untersuchungen an unbewehrtem und bewehrtem polymermodifiziertem Beton unter mehrfach wiederholter Druck- und Zugbeanspruchung vorgestellt und mit den Ergebnissen ähnlicher Versuche an Normalbeton und hochfestem Beton verglichen. Besondere Aufmerksamkeit wird dabei dem Formänderungsverhalten, der Steifigkeitsdegradation und der Energiedissipation sowie dem Kriechverhalten und der Mitwirkung des Betons zwischen den Rissen gewidmet. Die beobachtete signifikante Steifigkeitsdegradation sowie der ausgeprägt nichtlineare Zusammenhang zwischen der viskosen Verformung und der elastischen Stauchung zeigen, dass bei der Analyse der Kriech¬aus¬wirkungen des polymermodifizierten Betons auf das Tragverhalten entsprechender Kon¬struktionen neben den Gebrauchslasten auch die während der Lastgeschichte aufgetretenen maximalen Beanspruchungssituationen sowie die damit verbundenen Strukturveränderungen zu berücksichtigen sind. Auf der Basis der Versuchsergebnisse und der visko-elastisch-plastischen Kontinuumsschädigungstheorie werden rheologische Modelle zur Beschreibung des zeit- und beanspruchungsabhängigen Tragverhaltens von Betonbauteile vorgeschlagen. Die numerische Umsetzung der vorgeschlagenen Modelle erfolgt unter Berücksichtigung des zeitabhängigen Materialverhaltens des Betons auf der Basis des HAMILTON-Prinzips unter Vernachlässigung der Trägheitskräfte. Durch eine zeitliche Diskretisierung kann die Problembeschreibung auf das Prinzip von LAGRANGE vom Minimum des Gesamtpotentials zurückgeführt und als nichtlineare Optimierungsaufgabe formuliert werden. Die Simulation des beanspruchungsabhängigen Tragverhaltens von Stahlbetonverbundquerschnitten verdeutlicht die Qualität und Leistungsfähigkeit der vorgeschlagenen Modellbildung. N2 - The experimental results of the investigations into polymer-modified concrete with multifariously repeated compression or tension load are introduced in the provided work and compared to similar experiments in normal- and high-strength concrete. Special attention is dedicated to the stress-strain relation, the degradation of stiffness and the dissipation of energy as well as the non-linear long-term behaviour and tension-stiffening. Stiffness degradation and non-linear creep of polymer-modified concrete show that maximum strain situations have to be taken into consideration of the behaviour analysis of concrete structures under long-term loading. Based on experimental results and the theory of visco-elastic-plastic continuum damage, rheological models are suggested for the description of the time- and damage-dependent behaviour of reinforced concrete. The numerical concept is based on the HAMILTON-principle. Using time discretisation, mechanical modelling simplifies and can be described as a LAGRANGE-principle concerning minimum of total potential energy. The problem is solved by non-linear optimisation. The efficiency of the suggested model was proven for reinforced concrete cross sections by numerical simulation. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 10 KW - Kriechen KW - Kunstharzmodifizierter Zementbeton KW - Beton KW - Tragverhalten KW - Bruchverhalten KW - Experiment KW - Deformationsverhalten KW - Stoffgesetz KW - nichtlineare Optimierung KW - Simulation KW - Formänderungsenergie KW - Steifigkeitsdegradation KW - Creep KW - damage KW - tension-stiffening KW - dissipation of energy KW - non-linear optimisation Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20080102-11753 SN - 978-3-86068-331-2 ER - TY - JOUR A1 - Semenov, Vitaly A1 - Alekseeva, Elena A1 - Tarlapan, Oleg T1 - Virtual Construction using Map-based Approach N2 - The paper presents a general map-based approach to prototyping of products in virtual reality environments. Virtual prototyping of products is considered as a consistent simulation and visualization process mapping the source product model into its target visual representations. The approach enables to interrelate formally the product and visual information models with each other by defining mapping rules, to specify a prototyping scenario as a composition of map instances, and then to explore particular product models in virtual reality environments by interpreting the composed scenario. Having been realized, the proposed approach provides for the strongly formalized method and the common software framework to build virtual prototyping applications. As a result, the applications gain in expressiveness, reusability and reliability, as well as take on additional runtime flexibility... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Virtuelle Realität KW - Bauwerk Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2447 ER - TY - THES A1 - Schneider, Jens T1 - Untersuchungen zum Alterungsverhalten und zur Langzeitstabilität von Y-TZP/Al2O3-Dispersionskeramiken (ATZ) für die Anwendung in der Hüft-Endoprothetik N2 - 6 Zusammenfassung und Ausblick Die hydrothermal induzierte Phasentransformation konnte für ATZ-Keramik mit tiefenge-mittelten und tiefenaufgelösten Methoden charkterisiert und quantifiziert werden. Die zeit- und temperaturabhängige Alterungskinetik von ATZ wurde durch neun Tempera-turstufen in einem Temperaturbereich von 50 °C bis 134 °C untersucht und die kinetischen Parameter nummerisch bestimmt. Für 3Y-TZP wurde diese Prozedur bei drei Temperaturen im Temperaturbereich von 70 °C bis 134 °C angewendet. Aufgrund des ARRHENIUS-Verhaltens der Umwandlungskinetik konnte der zeitliche Verlauf der isotherm stattfinden-den hydrothermal induzierten Phasentransformation bei Körpertemperatur simuliert wer-den. Die Simulation dient zur Bewertung der Langzeitstabilität von medizinischen Implanta-ten aus ATZ bzw. 3Y-TZP. Die Untersuchungen wurden in Wasser und in Wasserdampf bzw. wasserdampfgesättigter Luft durchgeführt. Die Langzeitsimulation für 3Y-TZP wurde an-hand von Explantat-Untersuchungen verifiziert. ATZ zeigt gegenüber 3Y-TZP eine höhere Alterungsstabilität bezogen auf die zeitliche Ent-wicklung der monoklinen Phase. Im Hinblick auf die Oberflächenhärte, die durch die Pha-senumwandlung stark beeinflusst wird, erweist sich ATZ über einen langen Alterungszeit-raum stabiler als 3Y-TZP. Bis zu einem monoklinen Gehalt von 40 % beweist ATZ einen deutlichen Härtevorteil gegenüber 3Y TZP, dieser entspricht in der Langzeitsimulation für die Wasserlagerung ca. 35 Jahre. Das wirkt sich insbesondere bei Verschleißpaarungen wie beim künstlichen Hüftgelenk positiv aus. Verschleißuntersuchungen an einer neu entwickelten Kugel-auf-Scheibe-Geometrie mit li-nearer Kinematik, die dem Hüftgelenk nachempfunden wurde, belegen die vorteilhaften Verschleißeigenschaften von ATZ in Form von sehr geringen Abtragsraten und einer intak-ten Oberfläche nach 720 000 absolvierten Zyklen. Dabei wurde sogar eine Aufhärtung der Oberfläche durch die Verschleißbeanspruchung um bis zu 8 % nachgewiesen. Bei der tiefengemittelten Charakterisierung der hydrothermalen Alterung wurde in beiden Materialtypen festgestellt, dass die Geschwindigkeit der Phasentransformation neben der Temperatur merklich von der Änderung der H2O-Stoffmengenkonzentrantion an der Ober-fläche der Keramik abhängig ist, was sich mit den unterschiedlichen Aktivierungsenergien für Wasser- bzw. Wasserdampflagerung belegen lässt. Die Aktivierungsenergie Ea der hyd-rothermalen Phasentransformation wurde mit Hilfe der ARRHENIUS-Beziehung ermittelt und beträgt für ATZ bei Wasserdampflagerung 102 kJ/mol und bei Wasserlagerung 92 kJ/mol. Für Y-TZP beträgt die Aktivierungsenergie 114 kJ/mol bei Wasserdampflagerung und 102 kJ/mol bei Wasserlagerung. Der resultierende präexponentielle Faktor k0 unterscheidet sich für Wasserlagerung und Wasserdampflagerung um eine Größenordnung, was auf einen leicht andersartigen thermisch aktivierten Gesamtprozess hinweist. Der Avrami-Exponent n, der einen Hinweis auf den Mechanismus der Keimbildung sowie deren geometrische Ordnung geben kann, zeigte keine signifikante Abhängigkeit von der Temperatur und vom Umgebungsmedium. Er ist dagegen zeitabhängig und fällt mit zuneh-mender Alterungszeit, d.h. mit zunehmendem monoklinem Gehalt von ca. 4 auf 0,5 ab, was auf eine abnehmende Keimbildungsrate hindeutet. In Verbindung mit weiteren Untersu-chungen durch unabhängige und zum Teil tiefenauflösende Methoden wie GIXRD, NRA und Knoop-Mikrohärte-Messungen lässt sich der Alterungsmechanismus, bzw. sein zeitlicher und örtlicher Ablauf, durch die drei Stadien A, B und C beschreiben: A 0-5 ma. % m-ZrO2 Quasi-homogene Keimbildung an bevorzugten Orten wie Kornkan-ten und Kornecken (n≈4), Wassertransport wahrscheinlich via Korngrenzendiffusion, Aufhärtung der Oberfläche B 5-40 ma. % m-ZrO2 Keimbildung an den Korngrenzflächen bis zur Keimsättigung (n≈2), monokline Randschicht wächst zeitlich linear, Wassertransport konvektiv über Mikrorisse, deutlicher Härteverlust der Oberfläche C ≥ 40 ma. % m-ZrO2 Wachstum der monoklinen Kristallite von den Korngrenzflächen in die tetragonalen Kristallite unter starker Verzwillingung (n≈0,5), Abnahme der tetragonalen Kristallitgröße, starke Mikrorissbildung, dramatischer Rückgang der Oberflächenhärte Die Kristallitgröße der monoklinen Phase verbleibt im ATZ über alle drei Abschnitte bei 30 ±5 nm. Ein Anwachsen der Kristallite ist mechanische behindert. Kleinere monokline Kristallite sind im ATZ thermodynamisch instabil. Die Kristallitgröße der tetragonalen Phase fällt in den Abschnitten A und B sehr langsam und in C sehr schnell bis auf 25 nm ab. Bei dieser Kristallitgröße ist die tetragonale Phase gegenüber der monoklinen Phase thermody-namisch stabil. Diese residualen tetragonalen Kristallite weisen nach vollständigem Reakti-onsablauf einem Anteil von 7 ma. % auf. Der Sättigungsgehalt der monoklinen Phase betrug in beiden Materialen unabhängig von der Temperatur bzw. dem Umgebungsmedium 75 % der ZrO2-Phase. In Abschnitt C besitzt die residuale tetragonale Phase eine starke Orientierung. Dadurch wird die geometrische Bedingtheit der hydrothermal induzierten Phasenumwandlung ver-deutlicht. Die monokline Phase ist über den gesamten Alterungsprozess stark nach m(1 1  1) orientiert, was mit einer bevorzugten Umklapprichtung der c-Achse zur freien Oberfläche hin verbunden ist. Mit Hilfe der tiefenaufgelösten Phasenanalyse konnte die Wachstumsgeschwindigkeit der monoklinen Randschicht von der Oberfläche in das Volumen untersucht werden. Die Ge-schwindigkeit des Schichtwachstums ist in Abschnitt B nicht zeit- und tiefenabhängig, son-dern konstant mit ausgeprägtem ARRHENIUS-Verhalten (Temperaturabhängigkeit). Die Akti-vierungsenergie der Schichtwachstumsgeschwindigkeit km liegt in der gleichen Größenord-nung wie die der Transformationskonstante k. Die Umwandlungszone schreitet also mit konstanter Geschwindigkeit in das Volumen fort und hinterlässt ein verzweigtes Mikro- und Nanoriss-System. FESEM-Aufnahmen bestätigen das Vorhandensein einer porösen Randschicht, durch die das Wasser nahezu ungehindert eindringen kann. NRA Untersuchungen deuten in Stadium A auf Korngrenzendiffusion hin und bestätigen in Stadium B einen konvektiven Transport des Wassers an die Transformationszone. Eine Dif-fusion über Sauerstoffleerstellen im Gitter konnte anhand von Proben aus 8YSZ nicht nach-gewiesen werden. Dagegen kommt es in dem verzweigten Riss- und Porensystem in der gealterten Randschicht zum Rücktransport des Wassers an die Oberfläche, sobald die Pro-ben aus der hydrothermalen Atmosphäre genommen, an Luft gelagert oder in die Hochva-kuumkammer der NRA-Messapparatur eingeschleust werden. Mikrostrukturelle Untersuchungen an eigens entwickelten Verschleißpaarungen zeigten nach 720000 Zyklen ähnliche Oberflächeneigenschaften wie im Alterungsstadium A. Man kann daher davon ausgehen, dass die Stadien B und C aus Stabilitätsgründen in der tribolo-gischen Kontaktzone nicht existieren können und es dass sich im Falle einer gleichzeitigen, hydrothermalen und tribologischen Beanspruchung um einen stationären Alterungs- und Verschleißprozess handelt. Durch quasiplastische Deformation der monoklinen und tetra-gonalen Kristallite wird die Verschleißrate und die Abriebpartikel bei einer hart /hart Paa-rung aus ATZ deutlich minimiert, so dass ATZ für die Hüftendoprothetik ein durchaus geeig-neten Werkstoff darstellt, der sich auf der Grundlage der in dieser Arbeit gewonnenen Daten über eine Imlantationsdauer von .mehr als 15 Jahre stabil verhalten kann. KW - Dispersionskeramik KW - Hüftgelenkprothese KW - ATZ KW - Alterung KW - Simulation KW - GIXRD KW - NRA KW - Tribologie KW - Knoop Mikrohärte Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20121130-17761 ER - TY - JOUR A1 - Bourikas, Leonidas A1 - James, Patrick A. B. A1 - Bahaj, AbuBakr S. A1 - Jentsch, Mark F. A1 - Shen, Tianfeng A1 - Chow, David H. C. A1 - Darkwa, Jo T1 - Transforming typical hourly simulation weather data files to represent urban locations by using a 3D urban unit representation with micro-climate simulations JF - Future Cities and Environment N2 - Urban and building energy simulation models are usually driven by typical meteorological year (TMY) weather data often in a TMY2 or EPW format. However, the locations where these historical datasets were collected (usually airports) generally do not represent the local, site specific micro-climates that cities develop. In this paper, a humid sub-tropical climate context has been considered. An idealised “urban unit model” of 250 m radius is being presented as a method of adapting commonly available weather data files to the local micro-climate. This idealised “urban unit model” is based on the main thermal and morphological characteristics of nine sites with residential/institutional (university) use in Hangzhou, China. The area of the urban unit was determined by the region of influence on the air temperature signal at the centre of the unit. Air temperature and relative humidity were monitored and the characteristics of the surroundings assessed (eg green-space, blue-space, built form). The “urban unit model” was then implemented into micro-climatic simulations using a Computational Fluid Dynamics – Surface Energy Balance analysis tool (ENVI-met, Version 4). The “urban unit model” approach used here in the simulations delivered results with performance evaluation indices comparable to previously published work (for air temperature; RMSE <1, index of agreement d > 0.9). The micro-climatic simulation results were then used to adapt the air temperature and relative humidity of the TMY file for Hangzhou to represent the local, site specific morphology under three different weather forcing cases, (ie cloudy/rainy weather (Group 1), clear sky, average weather conditions (Group 2) and clear sky, hot weather (Group 3)). Following model validation, two scenarios (domestic and non-domestic building use) were developed to assess building heating and cooling loads against the business as usual case of using typical meteorological year data files. The final “urban weather projections” obtained from the simulations with the “urban unit model” were used to compare the degree days amongst the reference TMY file, the TMY file with a bulk UHI offset and the TMY file adapted for the site-specific micro-climate (TMY-UWP). The comparison shows that Heating Degree Days (HDD) of the TMY file (1598 days) decreased by 6 % in the “TMY + UHI” case and 13 % in the “TMY-UWP” case showing that the local specific micro-climate is attributed with an additional 7 % (ie from 6 to 13 %) reduction in relation to the bulk UHI effect in the city. The Cooling Degree Days (CDD) from the “TMY + UHI” file are 17 % more than the reference TMY (207 days) and the use of the “TMY-UWP” file results to an additional 14 % increase in comparison with the “TMY + UHI” file (ie from 17 to 31 %). This difference between the TMY-UWP and the TMY + UHI files is a reflection of the thermal characteristics of the specific urban morphology of the studied sites compared to the wider city. A dynamic thermal simulation tool (TRNSYS) was used to calculate the heating and cooling load demand change in a domestic and a non-domestic building scenario. The heating and cooling loads calculated with the adapted TMY-UWP file show that in both scenarios there is an increase by approximately 20 % of the cooling load and a 20 % decrease of the heating load. If typical COP values for a reversible air-conditioning system are 2.0 for heating and 3.5 for cooling then the total electricity consumption estimated with the use of the “urbanised” TMY-UWP file will be decreased by 11 % in comparison with the “business as usual” (ie reference TMY) case. Overall, it was found that the proposed method is appropriate for urban and building energy performance simulations in humid sub-tropical climate cities such as Hangzhou, addressing some of the shortfalls of current simulation weather data sets such as the TMY. KW - Mikroklima KW - Simulation KW - Stadt KW - Wetter KW - Idealised urban unit model, Micro-climate simulations, Urban weather projections, Cities Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170418-31348 UR - http://link.springer.com/article/10.1186/s40984-016-0020-4 ER - TY - JOUR A1 - Benz, Alexander A1 - Taraben, Jakob A1 - Lichtenheld, Thomas A1 - Morgenthal, Guido A1 - Völker, Conrad T1 - Thermisch-energetische Gebäudesimulation auf Basis eines Bauwerksinformationsmodells JF - Bauphysik N2 - Für eine Abschätzung des Heizwärmebedarfs von Gebäuden und Quartieren können thermisch-energetische Simulationen eingesetzt werden. Grundlage dieser Simulationen sind geometrische und physikalische Gebäudemodelle. Die Erstellung des geometrischen Modells erfolgt in der Regel auf Basis von Bauplänen oder Vor-Ort-Begehungen, was mit einem großen Recherche- und Modellierungsaufwand verbunden ist. Spätere bauliche Veränderungen des Gebäudes müssen häufig manuell in das Modell eingearbeitet werden, was den Arbeitsaufwand zusätzlich erhöht. Das physikalische Modell stellt die Menge an Parametern und Randbedingungen dar, welche durch Materialeigenschaften, Lage und Umgebungs-einflüsse gegeben sind. Die Verknüpfung beider Modelle wird innerhalb der entsprechenden Simulations-software realisiert und ist meist nicht in andere Softwareprodukte überführbar. Mithilfe des Building Information Modeling (BIM) können Simulationsdaten sowohl konsistent gespeichert als auch über Schnittstellen mit entsprechenden Anwendungen ausgetauscht werden. Hierfür wird eine Methode vorgestellt, die thermisch-energetische Simulationen auf Basis des standardisierten Übergabe-formats Industry Foundation Classes (IFC) inklusive anschließender Auswertungen ermöglicht. Dabei werden geometrische und physikalische Parameter direkt aus einem über den gesamten Lebenszyklus aktuellen Gebäudemodell extrahiert und an die Simulation übergeben. Dies beschleunigt den Simulations-prozess hinsichtlich der Gebäudemodellierung und nach späteren baulichen Veränderungen. Die erarbeite-te Methode beruht hierbei auf einfachen Modellierungskonventionen bei der Erstellung des Bauwerksinformationsmodells und stellt eine vollständige Übertragbarkeit der Eingangs- und Ausgangswerte sicher. Thermal building simulation based on BIM-models. Thermal energetic simulations are used for the estimation of the heating demand of buildings and districts. These simulations are based on building models containing geometrical and physical information. The creation of geometrical models is usually based on existing construction plans or in situ assessments which demand a comparatively big effort of investigation and modeling. Alterations, which are later applied to the structure, request manual changes of the related model, which increases the effort additionally. The physical model represents the total amount of parameters and boundary conditions that are influenced by material properties, location and environmental influences on the building. The link between both models is realized within the correspondent simulation soft-ware and is usually not transferable to other software products. By Applying Building Information Modeling (BIM) simulation data is stored consistently and an exchange to other software is enabled. Therefore, a method which allows a thermal energetic simulation based on the exchange format Industry Foundation Classes (IFC) including an evaluation is presented. All geometrical and physical information are extracted directly from the building model that is kept up-to-date during its life cycle and transferred to the simulation. This accelerates the simulation process regarding the geometrical modeling and adjustments after later changes of the building. The developed method is based on simple conventions for the creation of the building model and ensures a complete transfer of all simulation data. KW - Building Information Modeling KW - Energiebedarf KW - Gebäudehülle KW - Schnittstelle KW - Simulation KW - BIM KW - Gebäudesimulation KW - IFC-basierte Gebäudesimulation KW - thermische Gebäudehülle KW - building simulation Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20181221-38354 N1 - Copyright 2018 Ernst & Sohn. Dieser Artikel kann für den persönlichen Gebrauch heruntergeladen werden. Andere Verwendungen bedürfen der vorherigen Zustimmung der Autoren und des Verlags Ernst & Sohn. Der folgende Artikel erschien in der Bauphysik 40 (2), 2018 und kann unter folgendem Link abgerufen werden. https://www.ernst-und-sohn.de/app/artikelrecherche/artikel.php?lang=de&ID=38470&utm_source=eus&utm_medium=artikel-db&utm_campaign=Bp_2018_2 IS - 40, Heft 2 SP - 61 EP - 67 ER - TY - JOUR A1 - Benz, Alexander A1 - Taraben, Jakob A1 - Lichtenheld, Thomas A1 - Morgenthal, Guido A1 - Völker, Conrad T1 - Thermisch-energetische Gebäudesimulation auf Basis eines Bauwerksinformationsmodells JF - Bauphysik N2 - Für eine Abschätzung des Heizwärmebedarfs von Gebäuden und Quartieren können thermisch-energetische Simulationen eingesetzt werden. Grundlage dieser Simulationen sind geometrische und physikalische Gebäudemodelle. Die Erstellung des geometrischen Modells erfolgt in der Regel auf Basis von Bauplänen oder Vor-Ort-Begehungen, was mit einem großen Recherche- und Modellierungsaufwand verbunden ist. Spätere bauliche Veränderungen des Gebäudes müssen häufig manuell in das Modell eingearbeitet werden, was den Arbeitsaufwand zusätzlich erhöht. Das physikalische Modell stellt die Menge an Parametern und Randbedingungen dar, welche durch Materialeigenschaften, Lage und Umgebungs-einflüsse gegeben sind. Die Verknüpfung beider Modelle wird innerhalb der entsprechenden Simulations-software realisiert und ist meist nicht in andere Softwareprodukte überführbar. Mithilfe des Building Information Modeling (BIM) können Simulationsdaten sowohl konsistent gespeichert als auch über Schnittstellen mit entsprechenden Anwendungen ausgetauscht werden. Hierfür wird eine Methode vorgestellt, die thermisch-energetische Simulationen auf Basis des standardisierten Übergabe-formats Industry Foundation Classes (IFC) inklusive anschließender Auswertungen ermöglicht. Dabei werden geometrische und physikalische Parameter direkt aus einem über den gesamten Lebenszyklus aktuellen Gebäudemodell extrahiert und an die Simulation übergeben. Dies beschleunigt den Simulations-prozess hinsichtlich der Gebäudemodellierung und nach späteren baulichen Veränderungen. Die erarbeite-te Methode beruht hierbei auf einfachen Modellierungskonventionen bei der Erstellung des Bauwerksinformationsmodells und stellt eine vollständige Übertragbarkeit der Eingangs- und Ausgangswerte sicher. Thermal building simulation based on BIM-models. Thermal energetic simulations are used for the estimation of the heating demand of buildings and districts. These simulations are based on building models containing geometrical and physical information. The creation of geometrical models is usually based on existing construction plans or in situ assessments which demand a comparatively big effort of investigation and modeling. Alterations, which are later applied to the structure, request manual changes of the related model, which increases the effort additionally. The physical model represents the total amount of parameters and boundary conditions that are influenced by material properties, location and environmental influences on the building. The link between both models is realized within the correspondent simulation soft-ware and is usually not transferable to other software products. By Applying Building Information Modeling (BIM) simulation data is stored consistently and an exchange to other software is enabled. Therefore, a method which allows a thermal energetic simulation based on the exchange format Industry Foundation Classes (IFC) including an evaluation is presented. All geometrical and physical information are extracted directly from the building model that is kept up-to-date during its life cycle and transferred to the simulation. This accelerates the simulation process regarding the geometrical modeling and adjustments after later changes of the building. The developed method is based on simple conventions for the creation of the building model and ensures a complete transfer of all simulation data. KW - Gebäudehülle KW - Energiebedarf KW - Simulation KW - Schnittstelle KW - Building Information Modeling KW - Gebäudesimulation KW - BIM KW - IFC-basierte Gebäudesimulation KW - thermische Gebäudehülle KW - building simulation Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20181102-38190 UR - https://e-pub.uni-weimar.de/opus4/frontdoor/index/index/docId/3835 N1 - Copyright 2018 Ernst & Sohn. Dieser Artikel kann für den persönlichen Gebrauch heruntergeladen werden. Andere Verwendungen bedürfen der vorherigen Zustimmung der Autoren und des Verlags Ernst & Sohn. Der folgende Artikel erschien in der Bauphysik 40 (2), 2018 und kann unter folgendem Link abgerufen werden. https://www.ernst-und-sohn.de/app/artikelrecherche/artikel.php?lang=de&ID=38470&utm_source=eus&utm_medium=artikel-db&utm_campaign=Bp_2018_2. IS - 40, Heft 2 SP - 61 EP - 67 ER - TY - JOUR A1 - Volkova, Viktorija T1 - The analysis of dynamic behaviour of pre-stressed systems under polyharmonic excitations N2 - Pre-stressed structural elements are widely used in large-span structures. As a rule, they have higher stiffness characteristics. Pre-stressed rods can be applied as girders of different purpose, and as their separate parts, e.g. rods of trusses and frames. Among numerous ways of prestressing the compression of girders, trusses, and frames by tightenings from high-strength materials is under common application. KW - Verkehrsplanung KW - Simulation KW - Baukonstruktion KW - Dynamische Belastung KW - Tragwerk / Vorspannung KW - Vorgespannte Konstruktion Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2656 ER - TY - JOUR A1 - Romberg, Richard A1 - Niggl, Andreas A1 - van Treeck, Christoph T1 - Structural Analysis based on the Product Model Standard IFC N2 - In this paper we present a computer aided method supporting co-operation between different project partners, such as architects and engineers, on the basis of strictly three-dimensional models. The center of our software architecture is a product model, described by the Industry Foundation Classes (IFC) of the International Alliance for Interoperability (IAI). From this a geometrical model is extracted and automatically transferred to a computational model serving as a basis for various simulation tasks. In this paper the focus is set on the advantage of the fully three-dimensional structural analysis performed by p-version of the finite element analysis. Other simulation methods are discussed in a separate contribution of this Volume (Treeck 2004). The validity of this approach will be shown in a complex example. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Statik KW - Standard Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2433 ER - TY - CHAP A1 - Fedior, Marco A1 - Hamel, Wido ED - Steiner, Maria ED - Theiler, Michael ED - Mirboland, Mahsa T1 - Simulationsumgebung zur Evaluation von umweltorientierten Verkehrsmanagement-Strategien T2 - 30. Forum Bauinformatik N2 - Der vorliegende Beitrag beschreibt die Problematik bei der Prognose verkehrsbedingter Schadstoff-Immissionen. Im Mittelpunkt steht die Entwicklung und der Aufbau einer Simulationsumgebung zur Evaluation von umweltorientierten Verkehrsmanagement-Strategien. Die Simulationsumgebung wird über die drei Felder Verkehr, Emission, Immission entwickelt und findet zunächst Anwendung in der Evaluation verkehrlicher Maßnahmen für die Friedberger Landstraße in Frankfurt am Main. KW - Verkehr KW - Simulation KW - Emission KW - Luftverunreinigender Stoff Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20190328-38678 ER - TY - BOOK ED - Hildebrand, Jörg ED - Loose, Tobias ED - Sakkiettibutra, Jens ED - Brand, Marcus T1 - Simulationsforum 2013 - Schweißen und Wärmebehandlung N2 - Das Buch veröffentlicht 22 Fachbeiträge der Konferenz "Simulationsforum 2013 - Schweißen und Wärmebehandlung". KW - Schweißen KW - Wärmebehandlung KW - Simulation KW - Stahl KW - Modellierung Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20140512-21820 SN - 978-3-00-045902-3 PB - Förderverein Wärmebehandlung und Schweißen e.V. CY - Weimar ER - TY - THES A1 - Rahm, Tobias T1 - Simulation von Kernprozessen eines Erddruckschildes T1 - Process simulation of an Earth Pressure Balanced Shield Machine N2 - In dieser Arbeit wird der Vortriebsprozess einer Erddruckschildmaschine in einem Simulationsmodell mit Hilfe der System Dynamics modelliert. Nach einer Einführung in den maschinellen Tunnelbau werden die Besonderheiten der Erddruckschildmaschine herausgestellt. Anschließend wird das betrachtete System mit dem Simulationskonzept der System Dynamics modelliert und in einem geeigneten Simulationstool implementiert. N2 - Within this paper the heading of an Earth Pressure Balanced Shield Machine is modelled with the help of System Dynamics. The first chapter gives a short introduction to mechanized tunnelling. Then the characteristics of the Earth Pressure Balanced Shield Machine are discussed in more detail. After that, the system is modelled with the concept of System Dynamics and finally implemented in a simulation tool. KW - Simulation KW - Kontinuierliche Simulation KW - Computersimulation KW - System Dynamics KW - Modellierung KW - Tunnelbau KW - Schildmaschinen KW - Erddruckschildmaschine KW - Earth Pressure Balanced Shield Machine Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20110909-15599 ER - TY - THES A1 - Ansari, Meisam T1 - Simulation methods for functional and microstructured composite materials T1 - Simulationsmethoden für funktionalisierte und mikrostrukturierte Verbundwerkstoffe N2 - In this thesis, a generic model for the post-failure behavior of concrete in tension is proposed. A mesoscale model of concrete representing the heterogeneous nature of concrete is formulated. The mesoscale model is composed of three phases: aggregate, mortar matrix, and the Interfacial Transition Zone between them. Both local and non-local formulations of the damage are implemented and the results are compared. Three homogenization schemes from the literature are employed to obtain the homogenized constitutive relationship for the macroscale model. Three groups of numerical examples are provided. N2 - In dieser Arbeit wird ein generisches Modell für das nichtlineare Materialverhalten des Betons unter Spannung vorgeschlagen. Ein Mesoskalenmodell wird aufgebildet, welches die heterogene Materialstruktur des Betons darstellt. Das Mesoskalenmodell besteht aus drei Phasen: groben Zuschlägen, Mörtelmatrix und Übergangszone zwischen Zuschlag und Matrix. Es werden sowohl die lokale als auch die nichtlokale Formulierung des Schädigungsgrades implementiert und die Ergebnisse verglichen. Drei Homogenisierungsmethoden aus der Literatur werden verwendet, um die homogenisierte konstitutive Beziehung für das Makroskalenmodell zu erhalten. Drei Gruppen von numerischen Beispielen werden angeführt. KW - Simulation KW - Verbundwerkstoff KW - Beton KW - Meso-Scale KW - Composite KW - Concrete Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20201103-42783 ER - TY - THES A1 - Rauch, Kristin T1 - Simulation - Termincontrolling beim Bau einer Brückenkappe T1 - Simulation - critical path monitoring for the construction of a bridge curb N2 - Die Simulation ist vor allem in der Forschung und Wissenschaft ein bekanntes Ver-fahren zur Untersuchung von dynamischen Prozessen. Fachgebiete wie u.a. die Medizin und Biologie, das Verkehrswesen, die Automobilindustrie, die Meteorologie und die Fertigungstechnik gewinnen neue Erkenntnisse aus dem Einsatz derartiger Analyseverfahren. Gründe für die Anwendung von Computersimulationen erstrecken sich von finanziellen und zeitlichen Aspekten über eine Risikoverringerung bis hin zu einer vereinfachten Vorgehensweise. Nicht in allen Bereichen aber werden die viel-seitigen Vorteile von Simulationsmethoden genutzt. In der Baubranche wird Simulation derzeit nur ansatzweise eingesetzt. Doch vor al-lem Baustellen bieten durch den zunehmenden Kosten- und Termindruck sowie viel-seitige andere Einflüsse eine gute Basis für die Anwendung von Simulationsmetho-den. Der Bauablauf kann dadurch besser kontrolliert und gesteuert werden. In der Planungsphase von Bauprojekten wird Simulation bereits in Grundzügen für die Op-timierung von Bauablauf- und Logistikprozessen genutzt. Allerdings ist besonders die Ausführungsphase durch Störungen und Änderungen geprägt, sodass hier Simu-lationsmethoden noch effektiver eingesetzt werden können. Im Rahmen dieser Arbeit sollen die Einsatzmöglichkeiten von Simulationsmethoden für die Optimierung des Termincontrollings untersucht werden. Durch das Aufzeigen verschiedener Methoden sowie einem Vergleich über ihre Vor- und Nachteile wird herausgefiltert, welches Simulationswerkzeug am effektivsten im Termincontrolling eingesetzt werden kann. Ein weiteres Ziel dieser Arbeit ist die Modellierung eines Beispielprozesses anhand eines ausgewählten Simulationsverfahrens. Die Herstellung einer Brückenkappe wird in diesem Zusammenhang umfangreich dargestellt und analysiert. Eventuelle Zwangspunkte bei der Umsetzung und verschiedene Lösungsmöglichkeiten werden aufgezeigt. N2 - Simulation as supporting method to analyse difficult processes is already successful implemented in different domains, but it is also increasingly used in the construction industry. Above all infrastructure construction sites are characterised by enormous pressure of time and costs. For solving these problems and controlling the construction progress, simulation tools can be used more intensively. Up to now these tools are applied only in the start-up phase of a project for the optimisation of construction and logistic processes. But especially the construction phase is characterised by disturbances and changes. The topic of this master thesis “Simulation – critical path monitoring for the construction of a bridge curb” deals with developments to optimise the controlling of the construction progress by using simulation. At first different modelling methods are showed and analysed, how they can be used to simulate construction processes. Then a detailed investigation of the building of a bridge curb follows. Subsequent this construction progress is simulated with the computer program “Plant Simulation”. Finally limits of simulation tools are analysed and future lines of development are demonstrated. KW - Simulation KW - Termincontrolling KW - Bauablauf KW - Prozessoptimierung KW - Brückenkappe KW - simulation KW - critical path monitoring KW - construction progress KW - process optimisation KW - bridge curb Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20081111-14414 ER - TY - CHAP A1 - König, Reinhard A1 - Müller, Daniela T1 - Simulating the development of residential areas of the city of Vienna from 1888 to 2001 T2 - Compendium of Abstracts of the 8th International Conference on Urban Planning and Environment (UPE8) N2 - The structure and development of cities can be seen and evaluated from different points of view. By replicating the growth or shrinkage of a city using historical maps depicting different time states, we can obtain momentary snapshots of the dynamic mechanisms of the city. An examination of how these snapshots change over the course of time and a comparison of the different static time states reveals the various interdependencies of population density, technical infrastructure and the availability of public transport facilities. Urban infrastructure and facilities are not distributed evenly across the city – rather they are subject to different patterns and speeds of spread over the course of time and follow different spatial and temporal regularities. The reasons and underlying processes that cause the transition from one state to another result from the same recurring but varyingly pronounced hidden forces and their complex interactions. Such forces encompass a variety of economic, social, cultural and ecological conditions whose respective weighting defines the development of a city in general. Urban development is, however, not solely a product of the different spatial distribution of economic, legal or social indicators but also of the distribution of infrastructure. But to what extent is the development of a city affected by the changing provision of infrastructure? As KW - urban simulation KW - Simulation Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20160622-26066 CY - Kaiserslautern, Germany ER - TY - CHAP A1 - Kath, Thilo T1 - Sicher arbeiten mit Kränen durch Simulation und Visualisierung N2 - Bestimmungen und Anforderungen an den Entwurf von Baustelleneinrichtungen (BE), Kraneinsatzplan als Bestandteil der BE, planungstechnische Aspekte, Untersuchung von CAD-Anwendungen für die Planung von Baustelleneinrichtungen, Entwicklung eines Kraneinsatzplaners, Sicherheitsaspekte bei der Planung von Baukraneinsätzen. Es zeigte sich, dass gerade die Forderung der Betrachtung kausaler und räumlicher Abhängigkeiten mit den in der Praxis angewandten Planungswerkzeugen nicht oder nur eingeschränkt realisierbar ist. Mit dem Programm >EasyCrane TK< wird eine Möglichkeit aufgezeigt, die Erstellung von Kraneinsatzplänen effizienter und für die Umsetzung auf der Baustelle sicherer zu gestalten. KW - Arbeitsschutz KW - Baustelle KW - Baubetriebslehre KW - Simulation KW - Visualisierung KW - Kran KW - Arbeitsstättenverordnung KW - Baustelleneinrichtung Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-6901 ER - TY - JOUR A1 - Osada, Teppei A1 - Koike, Hirotaka A1 - Morimoto, Akinori T1 - Research on Establishment of a Standard of Traffic Impact Assessment with Integrated Database System N2 - Planning support systems, such as geographical information system (GIS) and traffic flow simulation models, are widely in use in recent urban planning research. In this paper we propose a method to apply traffic impact assessment (TIA) to large-scale, commercial developments. In TIA research we often encounter the problem of increasing amount of data that is necessary for detailed investigation and analysis, as the scale of commercial developments become larger and more complex. As a result, TIA presents two problems. The first problem is the difficulty of data acquisition. The second problem is the reliability of data. As a solution, we developed an integrated database system. KW - Verkehrsplanung KW - Simulation KW - Datenbanksystem Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2647 ER - TY - JOUR A1 - Kiviniemi, Arto A1 - Fischer, Martin T1 - Requirements Management Interface to Building Product Models N2 - In current AEC practice client requirements are typically recorded in a building program, which, depending on the building type, covers various aspects from the overall goals, activities and spatial needs to very detailed material and condition requirements. This documentation is used as the starting point of the design process, but as the design progresses, it is usually left aside and changes are made incrementally based on the previous design solution. These incremental small changes can lead to a solution that may no longer meet the original requirements. In addition, design is by nature an iterative process and the proposed solutions often also cause evolution in the client requirements. However, the requirements documentation is usually not updated accordingly. Finding the latest updates and evolution of the requirements from the documentation is very difficult, if not impossible. This process can lead to an end result, which is significantly different from the documented requirements. Some important requirements may not be satisfied, and even if the design process was based on agreed-upon changes in the scope and requirements, differences in the requirements documents and in the completed building can lead to well-justified doubts about the quality of the design and construction process... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Bauwerk KW - Modellierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2427 ER - TY - JOUR A1 - Holtzhauer, Eric A1 - Saal, Helmut T1 - Product modelling in the steel construction domain N2 - The complexity of the relationships between the actors of a building project requires high efficiency in communication. Among other things, data sharing is crucial. The exchange of data is made possible by interfaces between expert programs, which rely on product models. The latter are neutral standards with formal definitions of building objects and their attributes. This paper deals with the state of the art and the research activities concerning product models in the steel construction domain and the advantages provided by this technology for the sector. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Stahlbau Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2415 ER - TY - JOUR A1 - Kang, Shihchung A1 - Miranda, Eduardo T1 - Physics Based Model for Simulating the Dynamics of Tower Cranes N2 - The goal of the research is to increase the understanding of dynamic behaviors during the crane operation, and develops computer-aided methods to improve the training of crane operators. There are approximately 125,000 cranes in operation today in the construction industry, responsible for major portion of erection activities. Unfortunately, many accidents occur every year in the U.S. and other countries related to the operation of cranes in construction sites. For example on November 28, 1989 a tower crane collapse during the construction of a building in San Francisco killing four construction workers, one civilian and injuring 28. According to the statistics from Occupational Safety Health Administration (OSHA), there were 137 crane-related fatalities from 1992 to 2001 in the US. A well-known internet website that keeps track of crane-related accidents (craneaccidents.com), reports 516 accidents and 277 fatalities from 2000 to 2002. These statistics show that even though many measures have been taken to decrease the number of crane-related accidents (Braam, 2002), the number of crane related accidents is still very large. It is important to recognize that each construction related fatality is not only a great human loss but also increases the costs of insurance, lawsuits, and the construction budget due to delay of a project (Paulson 1992)... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Turmdrehkran KW - Dynamische Belastung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2409 ER - TY - JOUR A1 - Gao, Zuoren A1 - Wu, Weiyu A1 - Ren, Aizhu T1 - Physically Based Modeling and Multi-Physical Simulation System for Wood Structure Fire Performance N2 - This research is devoted to promoting the performance-based engineering in wood structure fire. It looks into the characteristic of the material, structural composing and collapse detecting to find out the main factors in the wood structure collapse in fire. The aim of the research is to provide an automatic simulation platform for the complicated circulation. A physically based model for slim member for beams and columns and a frame of multi-physical simulation are provided to implement the system. The physically based model contains material model, structural mechanics model, material mechanics model, as well as geometry model for the compositive simulation. The multi-physical simulation is built on the model and has the capacity to carry out a simulation combining structural, fire (thermal, CFD) and material degradation simulation. The structural and fire simulation rely on two sophisticated software respectively, ANSYS (an FEA software) and FDS (with a core of CFD). Researchers of the paper develop system by themselves to combine the two existing ones. The system has the capability to calculate the wood char to find out the loss of cross-section and to detect the collapse caused in different ways. The paper gives a sample of Chinese traditional house to show how this simulation system works. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Holzbau KW - Brandschutz Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2381 ER - TY - JOUR A1 - Shih, Naai-Jung A1 - Lee, Wen-Pang T1 - Particle Simulation and Evaluation of Personal Exposure to Contaminant Sources in an Elevation Space N2 - An elevator, which figures a small volume, is normally used by everyone for a short period of time and equipped with simple ventilation system..Any contaminant released within it may cause serious problem. This research adapt a fire and smoke simulation software (FDS) into non-fire indoor airflow scario. Differently from previous research, particles are chosen as a risk evalution unit. A personal and multi-personal exposure model is proposed. The model takes the influence of the human thermal boundary, coughing, inhalation, exhalation, standing position, and the fan factor into account. The model is easy-to-use and suitable for the design of elevator system in practice. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Luft KW - Schadstoffkonzentration Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2376 ER - TY - THES A1 - Schemmann, Christoph T1 - Optimierung von radialen Verdichterlaufrädern unter Berücksichtigung empirischer und analytischer Vorinformationen mittels eines mehrstufigen Sampling Verfahrens T1 - Optimization of Centrifugal Compressor Impellers by a Multi-fidelity Sampling Method Taking Analytical and Empirical Information into Account N2 - Turbomachinery plays an important role in many cases of energy generation or conversion. Therefore, turbomachinery is a promising approaching point for optimization in order to increase the efficiency of energy use. In recent years, the use of automated optimization strategies in combination with numerical simulation has become increasingly popular in many fields of engineering. The complex interactions between fluid and solid mechanics encountered in turbomachines on the one hand and the high computational expense needed to calculate the performance on the other hand, have, however, prevented a widespread use of these techniques in this field of engineering. The objective of this work was the development of a strategy for efficient metamodel based optimization of centrifugal compressor impellers. In this context, the main focus is the reduction of the required numerical expense. The central idea followed in this research was the incorporation of preliminary information acquired from low-fidelity computation methods and empirical correlations into the sampling process to identify promising regions of the parameter space. This information was then used to concentrate the numerically expensive high-fidelity computations of the fluid dynamic and structure mechanic performance of the impeller in these regions while still maintaining a good coverage of the whole parameter space. The development of the optimization strategy can be divided into three main tasks. Firstly, the available preliminary information had to be researched and rated. This research identified loss models based on one dimensional flow physics and empirical correlations as the best suited method to predict the aerodynamic performance. The loss models were calibrated using available performance data to obtain a high prediction quality. As no sufficiently exact models for the prediction of the mechanical loading of the impellercould be identified, a metamodel based on finite element computations was chosen for this estimation. The second task was the development of a sampling method which concentrates samples in regions of the parameter space where high quality designs are predicted by the preliminary information while maintaining a good overall coverage. As available methods like rejection sampling or Markov-chain Monte-Carlo methods did not meet the requirements in terms of sample distribution and input correlation, a new multi-fidelity sampling method called “Filtered Sampling“has been developed. The last task was the development of an automated computational workflow. This workflow encompasses geometry parametrization, geometry generation, grid generation and computation of the aerodynamic performance and the structure mechanic loading. Special emphasis was put into the development of a geometry parametrization strategy based on fluid mechanic considerations to prevent the generation of physically inexpedient designs. Finally, the optimization strategy, which utilizes the previously developed tools, was successfully employed to carry out three optimization tasks. The efficiency of the method was proven by the first and second testcase where an existing compressor design was optimized by the presented method. The results were comparable to optimizations which did not take preliminary information into account, while the required computational expense cloud be halved. In the third testcase, the method was applied to generate a new impeller design. In contrast to the previous examples, this optimization featuredlargervariationsoftheimpellerdesigns. Therefore, theapplicability of the method to parameter spaces with significantly varying designs could be proven, too. N2 - Turbomaschinen sind eine entscheidende Komponente in vielen Energiewandlungs- oder Energieerzeugungsprozessen und daher als vielversprechender Ansatzpunkt für eine Effizienzsteigerung der Energie-und Ressourcennutzung anzusehen. Im Laufe des letzten Jahrzehnts haben automatisierte Optimierungsmethoden in Verbindung mit numerischer Simulation zunehmend breitere Verwendung als Mittel zur Effizienzsteigerung in vielen Bereichen der Ingenieurwissenschaften gefunden. Allerdings standen die komplexen Interaktionen zwischen Strömungs- und Strukturmechanik sowie der hohe nummerische Aufwand einem weitverbreiteten Einsatz dieser Methoden im Turbomaschinenbereich bisher entgegen. Das Ziel dieser Forschungsaktivität ist die Entwicklung einer effizienten Strategie zur metamodellbasierten Optimierung von radialen Verdichterlaufrädern. Dabei liegt der Schwerpunkt auf einer Reduktion des benötigten numerischen Aufwandes. Der in diesem Vorhaben gewählte Ansatz ist das Einbeziehen analytischer und empirischer Vorinformationen (“lowfidelity“) in den Sampling Prozess, um vielversprechende Bereiche des Parameterraumes zu identifizieren. Diese Informationen werden genutzt um die aufwendigen numerischen Berechnungen (“high-fidelity“) des strömungs- und strukturmechanischen Verhaltens der Laufräder in diesen Bereichen zu konzentrieren, während gleichzeitig eine ausreichende Abdeckung des gesamten Parameterraumes sichergestellt wird. Die Entwicklung der Optimierungsstrategie ist in drei zentrale Arbeitspakete aufgeteilt. In einem ersten Schritt werden die verfügbaren empirischen und analytischen Methoden gesichtet und bewertet. In dieser Recherche sind Verlustmodelle basierend auf eindimensionaler Strömungsmechanik und empirischen Korrelationen als bestgeeignete Methode zur Vorhersage des aerodynamischen Verhaltens der Verdichter identifiziert worden. Um eine hohe Vorhersagegüte sicherzustellen, sind diese Modelle anhand verfügbarer Leistungsdaten kalibriert worden. Da zur Vorhersage der mechanischen Belastung des Laufrades keine brauchbaren analytischen oder empirischen Modelle ermittelt werden konnten, ist hier ein Metamodel basierend auf Finite-Element Berechnungen gewählt worden. Das zweite Arbeitspaket beinhaltet die Entwicklung der angepassten Samplingmethode, welche Samples in Bereichen des Parameterraumes konzentriert, die auf Basis der Vorinformationen als vielversrechend angesehen werden können. Gleichzeitig müssen eine gleichmäßige Abdeckung des gesamten Parameterraumes und ein niedriges Niveau an Eingangskorrelationen sichergestellt sein. Da etablierte Methoden wie Markov-Ketten-Monte-Carlo-Methoden oder die Verwerfungsmethode diese Voraussetzungen nicht erfüllen, ist ein neues, mehrstufiges Samplingverfahren (“Filtered Sampling“) entwickelt worden. Das letzte Arbeitspaket umfasst die Entwicklung eines automatisiertenSimulations-Workflows. Dieser Workflow umfasst Geometrieparametrisierung, Geometrieerzeugung, Netzerzeugung sowie die Berechnung des aerodynamischen Betriebsverhaltens und der strukturmechanischen Belastung. Dabei liegt ein Schwerpunkt auf der Entwicklung eines Parametrisierungskonzeptes, welches auf strömungsmechanischen Zusammenhängen beruht, um so physikalisch nicht zielführende Parameterkombinationen zu vermeiden. Abschließend ist die auf den zuvor entwickelten Werkzeugen aufbauende Optimierungsstrategie erfolgreich eingesetzt worden, um drei Optimierungsfragestellungen zu bearbeiten. Im ersten und zweiten Testcase sind bestehende Verdichterlaufräder mit der vorgestellten Methode optimiert worden. Die erzielten Optimierungsergebnisse sind von ähnlicher Güte wie die solcher Optimierungen, die keine Vorinformationen berücksichtigen, allerdingswirdnurdieHälfteannumerischemAufwandbenötigt. IneinemdrittenTestcase ist die Methode eingesetzt worden, um ein neues Laufraddesign zu erzeugen. Im Gegensatz zu den vorherigen Beispielen werden im Rahmen dieser Optimierung stark unterschiedliche Designs untersucht. Dadurch kann an diesem dritten Beispiel aufgezeigt werden, dass die Methode auch für Parameterräume mit stakt variierenden Designs funktioniert. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2019,3 KW - Simulation KW - Maschinenbau KW - Optimierung KW - Strömungsmechanik KW - Strukturmechanik Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20190910-39748 ER - TY - JOUR A1 - Vogel, Manfred A1 - Breit, Manfred A1 - Märki, Fabian T1 - Optimization of 4D Process Planning using Genetic Algorithms N2 - The presented work focuses on the presentation of a discrete event simulator which can be used for automated sequencing and optimization of building processes. The sequencing is based on the commonly used component–activity–resource relations taking structural and process constraints into account. For the optimization a genetic algorithm approach was developed, implemented and successfully applied to several real life steel constructions. In this contribution we discuss the application of the discrete event simulator including its optimization capabilities on a 4D process model of a steel structure of an automobile recycling facility. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Genetischer Algorithmus Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2360 ER - TY - THES A1 - Hildebrand, Jörg T1 - Numerische Schweißsimulation - Bestimmung von Temperatur, Gefüge und Eigenspannung an Schweißverbindungen aus Stahl- und Glaswerkstoffen T1 - Numerical welding simulation - determination of temperature, microstructure and residual stress for steel and glass materials in welded joints N2 - Die Komplexität des Schweißprozesses und das Verhalten der Werkstoffe infolge des Energieeintrages erfordern eine umfassende Betrachtungsweise. Die Entwicklung von numerischen Modellen und Methoden in den letzten 50 Jahren ermöglicht die Simulation, Analyse und Optimierung von Schweißverbindungen hinsichtlich Temperatur, Gefügestruktur und Eigenspannungen. Eine Differenzierung der Schweißsimulation in Prozess-, Werkstoff- und Struktursimulation gestattet eine gezielte Untersuchung von einzelnen Aspekten. Diese Unterteilung erfordert zum Teil eine starke Abstraktion und Idealisierung der Realität durch geeignete Annahmen und Randbedingungen, die von der zu untersuchenden Fragestellung abhängen. Dadurch wird eine Kalibrierung und Verifikation der Modelle mit Versuchsergebnissen notwendig. Die in dieser Arbeit durchgeführten Untersuchungen beschäftigen sich mit wichtigen Fragestellungen hinsichtlich der numerischen Simulation und experimentellen Untersuchung des Temperaturfeldes sowie des Gefüge- und Eigenspannungszustandes von MAG-Schweißverfahren an den Werkstoffen Feinkornbaustahl und Duplex-Stahl, CO2-Laserstrahlschweißverfahren am Werkstoff Quarzglas, Trennprozessen von Proben, WIG-Nachbehandlungsverfahren. Hinsichtlich der Naht- und Stoßarten orientierte sich die Arbeit an baupraktisch relevanten Schweißverbindungen sowie Besonderheiten, die sich aus Schweißprozessen und unterschiedlichen Werkstoffen ergeben. Eine Interpretation der numerisch und experimentell ermittelten Ergebnisse ermöglicht die Ableitung von allgemeingültigen Erkenntnissen zur Ausbildung des Temperaturfeldes, Entstehung von Gefügestrukturen und Eigenspannungen. Voraussetzungen für eine realitätsnahe Schweißsimulation zur Bestimmung von Temperatur, Gefügeanteil und Eigenspannung sind neben den Geometriemodellen geeignete numerische Modelle für die Einkopplung der Energie aus dem Schweißprozess und für die Abgabe der Energie durch Konvektion und Strahlung an die Umgebung, zur Beschreibung des thermischen und mechanischen Werkstoffverhaltens im Bereich von Raumtemperatur bis zur Schmelztemperatur. N2 - In the last 50 years simulation, analysis and optimization of welded joints makes the development possible of numerical models and methods for determination of temperature, microstructure and residual stress. A differentiation of welding simulation in process, material and structural simulation is possible for a purposeful investigation of individual aspects. This partitioning requires a strong abstraction and idealization of the reality with boundary conditions. Calibrations and verifications of the models with test results are necessary. The investigations concern with important questions in regard to the numerical simulation and experimental investigation of temperature field as well as microstructure and residual stresses of MAG-welding at the materials fine-grain structural steel and duplex steel, CO2-laser welding at the material quartz glass, separation processes of samples, post welding process with TIG. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 18 KW - MAG-Schweißen KW - Schweißen KW - Simulation KW - Eigenspannung KW - Feinkornbaustahl KW - Quarzglas KW - Schweißverbindung KW - Wärmeeinflusszone KW - Laserschweißen KW - Ferri KW - welding KW - numerical simulation KW - residual stress KW - joints KW - steel Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20090617-14753 ER - TY - THES A1 - Unger, Jörg F. T1 - Neural networks in a multiscale approach for concrete N2 - From a macroscopic point of view, failure within concrete structures is characterized by the initiation and propagation of cracks. In the first part of the thesis, a methodology for macroscopic crack growth simulations for concrete structures using a cohesive discrete crack approach based on the extended finite element method is introduced. Particular attention is turned to the investigation of criteria for crack initiation and crack growth. A drawback of the macroscopic simulation is that the real physical phenomena leading to the nonlinear behavior are only modeled phenomenologically. For concrete, the nonlinear behavior is characterized by the initiation of microcracks which coalesce into macroscopic cracks. In order to obtain a higher resolution of this failure zones, a mesoscale model for concrete is developed that models particles, mortar matrix and the interfacial transition zone (ITZ) explicitly. The essential features are a representation of particles using a prescribed grading curve, a material formulation based on a cohesive approach for the ITZ and a combined model with damage and plasticity for the mortar matrix. Compared to numerical simulations, the response of real structures exhibits a stochastic scatter. This is e.g. due to the intrinsic heterogeneities of the structure. For mesoscale models, these intrinsic heterogeneities are simulated by using a random distribution of particles and by a simulation of spatially variable material parameters using random fields. There are two major problems related to numerical simulations on the mesoscale. First of all, the material parameters for the constitutive description of the materials are often difficult to measure directly. In order to estimate material parameters from macroscopic experiments, a parameter identification procedure based on Bayesian neural networks is developed which is universally applicable to any parameter identification problem in numerical simulations based on experimental results. This approach offers information about the most probable set of material parameters based on experimental data and information about the accuracy of the estimate. Consequently, this approach can be used a priori to determine a set of experiments to be carried out in order to fit the parameters of a numerical model to experimental data. The second problem is the computational effort required for mesoscale simulations of a full macroscopic structure. For this purpose, a coupling between mesoscale and macroscale model is developed. Representative mesoscale simulations are used to train a metamodel that is finally used as a constitutive model in a macroscopic simulation. Special focus is placed on the ability of appropriately simulating unloading. N2 - Makroskopisch betrachtet kann das Versagen von Beton durch die Entstehung und das Wachstum von Rissen beschrieben werden. Im ersten Teil der Arbeit wird eine Methode zur Simulation der makroskopischen Rissentwicklung von Beton unter Verwendung von kohäsiven diskreten Rissen basierend auf der erweiterten Finiten Elemente Methode vorgestellt. Besondere Bedeutung liegt dabei auf der Untersuchung von Kriterien zur Rissentstehung und zum Risswachstum. Ein Nachteil von makroskopischen Simulationen liegt in der nur phänomenologischen Berücksichtigung der tatsächlichen Vorgänge. Nichtlineares Verhalten von Beton ist durch die Entstehung von Mikrorissen gekennzeichnet, die bei weiterer Belastung zu makroskopischen Rissen zusammenwachsen. Um die Versagenszone realitätsnah abbilden zu können, wurde ein Mesoskalenmodell von Beton entwickelt, welches Zuschläge, Matrix und Übergangszone zwischen beiden Materialien (ITZ) direkt abbildet. Hauptmerkmal sind die Simulation der Zuschläge nach einer Sieblinie, eine kohäsive Materialformulierung der ITZ und ein kombiniertes Model aus Schädigung und Plastizität für das Matrixmaterial. Im Gegensatz zu numerischen Simulationen ist die Systemantwort reeller Strukturen eine unscharfe Größe. Dies liegt u.a. an Heterogenitäten innerhalb der Struktur, die im Rahmen der Arbeit durch eine zufällige Verteilung der Zuschläge und über räumlich variierende Materialparameter unter Verwendung von Zufallsfeldern simuliert werden. Zwei Hauptprobleme sind bei den Mesoskalensimulationen aufgetreten. Einerseits sind Materialparameter auf der Mesoskala oft schwer zu bestimmen. Deswegen wurde eine Methode basierend auf Bayes neuronalen Netzen entwickelt, die eine Parameteridentifikation unter Verwendung von makroskopischen Versuchen erlaubt. Diese Methode ist aber universell anwendbar auf alle Parameteridentifikationsprobleme in numerischen Simulationen basierend auf experimentellen Daten. Der Ansatz liefert sowohl Informationen über den wahrscheinlichsten Parametersatz des Models zur numerischen Simulation eines Experiments als auch eine Einschätzung der Genauigkeit dieses Schätzers. Die Methode kann auch verwendet werden, um a priori einen Satz von Experimenten auszuwählen der notwendig ist, um die Parameter eines numerischen Modells zu bestimmen. Ein zweites Problem ist der numerische Aufwand von Mesoskalensimulationen für makroskopische Strukturen. Aus diesem Grund wurde eine Kopplungsstrategie zwischen Meso- und Makromodell entwickelt, bei dem repräsentative Simulationen auf der Mesoebene verwendet werden, um ein Metamodell zu generieren, welches dann die Materialformulierung in einer makroskopischen Simulation darstellt. Ein Fokus liegt dabei auf der korrekten Abbildung von Entlastungen. T2 - Neuronale Netze in einem Multiskalenansatz für Beton T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2009,1 KW - Beton KW - Mehrskalenmodell KW - Mehrskalenanalyse KW - Neuronales Netz KW - Monte-Carlo-Simulation KW - Simulation KW - Monte-Carlo-Integration KW - Kontinuierliche Simul KW - Bayes neuronale Netze KW - Parameteridentification KW - Bayesian neural networks KW - parameter identification Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20090626-14763 ER - TY - JOUR A1 - Rose, Martin T1 - Modeling of Freeway Traffic N2 - An integrated modeling of freeway traffic is developed, whose implementation in an uniform computer –aided simulation model facilitate comparative evaluation and systematic coupling of several traffic simulations, traffic controls, traffic measurements and traffic scenarios. The integrated modeling of freeway traffic is a basic mapping of freeway networks, control methods, measurements and different simulations of traffic flow... KW - Verkehrsplanung KW - Simulation KW - Autobahn Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2639 ER - TY - CHAP ED - Abrahamczyk, Lars ED - Schwarz, Jochen ED - Werner, Frank T1 - Model Validation and Simulation N2 - The Bauhaus Summer School series provides an international forum for an exchange of methods and skills related to the interaction between different disciplines of modern engineering science. The 2012 civil engineering course was held in August over two weeks at Bauhaus-Universität Weimar. The overall aim was the exchange of research and modern scientific approaches in the field of model validation and simulation between well-known experts acting as lecturers and active students. Besides these educational intentions the social and cultural component of the meeting has been in the focus. 48 graduate and doctoral students from 20 different countries and 22 lecturers from 12 countries attended this summer school. Among other aspects, this activity can be considered successful as it raised the sensitivity towards both the significance of research in civil engineering and the role of intercultural exchange. This volume summarizes and publishes some of the results: abstracts of key note papers presented by the experts and selected student research works. The overview reflects the quality of this summer school. Furthermore the individual contributions confirm that for active students this event has been a research forum and a special opportunity to learn from the experiences of the researchers in terms of methodology and strategies for research implementation in their current work. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 23 KW - Modeling KW - Validation KW - Simulation KW - Summer School Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20130805-19969 SN - 978-3-86068-502-0 PB - Verlag der Bauhaus-Universität Weimar CY - Weimar ER - TY - CHAP A1 - Zaneldin, Essam T1 - Investigate the Impact of Different Resource Allocation Strategies on the Design of Building Projects Using Simulation N2 - The design of building projects involves several types of resources such as architects, structural engineers, mechanical engineers, electrical engineers, and draftsmen, among others. For design firms to stay in business in this very competitive market, they need to manage their resources in a way that improves productivity and cost effectiveness. This task, however, is not simple and requires thorough analysis of process-level operations, resource use, and productivity. Typically, these operational aspects are the responsibility of the design office manager who assigns available resources to the different design projects to save time and lower design expenses. It is noted that limited studies have been carried out in the literature to model overall organizational operations and behavioral aspects, particularly in firms specialized in the design of building projects. In an effort to simplify the modeling process, a simplified modeling and simulation tool is used in this research. A simulation model representing an actual design office was developed assuming that the office performs designs for small, medium, and large size building projects. The developed model was used to simulate several alternatives and examine various resource assignment strategies. The simulation was conducted over ten years and the resulting productivity and income was measured. KW - Baubetrieb KW - Computerunterstütztes Verfahren KW - Simulation KW - Bauvorhaben Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1658 ER - TY - JOUR A1 - Neuberg, Frank A1 - Fank, Ernst A1 - Ekkerlein, Christian T1 - Integrated Life Cycle Simulation and Assessment of Buildings N2 - Buildings require both for construction and, due to their comparatively long life cycle for maintenance, significant raw material and energy resources. So far available knowledge about resource consumption during an entire life cycle of a building is still quite rare, because various criteria affect each other and/or overlay mutually. In this contribution a model based software concept is presented using an integrated approach for life cycle simulation and assessment of buildings. The essential point of the development consists of connecting an IFC compliant product model of a building via the Internet with data bases for the resource and energy requirement of building materials. Furthermore, numerical simulations allow calculating and minimizing the energy consumption, the resource requirement, the waste streams and also the noxious emissions. In the context of this paper we present the first release of software programs for architects and engineers, which help them to evaluate their design decisions objectively in early planning steps. Additionally the usage of the software is demonstrated by a test case study for a real world building. By applying this software in practice a substantial contribution for saving energy and natural resources can be provided in the sense of sustainable and ecological building design. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Lebenszyklus Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2351 ER - TY - CHAP A1 - Gebbeken, Norbert A1 - Baumhauer, Andreas A1 - Ionita, Mihai T1 - Increasing the Reliability and Performance through Automatization and Parallel Working N2 - Re-examination of the behaviour of structures can be necessary due to deterioration or changes in the traffic situation during their lifetime. The Finite Element Method (FEM) is widely used in order to accomplish numerical analysis. Considering the development of computer performance, more detailed FEM models can be analyzed, even on site, with mobile computers. To compensate the increasing amount of data needed for the model input, measures need to be taken to save time, by distributing the work. In order to provide consistency to the model, fedback data must be checked upon reception. A local wireless computer network of ultra-portable devices linked together with a computer can provide the coordination necessary for efficient parallel working. Based on a digital model consisting of all data gathered, structural modelling and numerical analysis are performed automatically. Thus, the user is released from the work that can be automatized and the time needed for the overall analysis of a structure is decreased. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Parallelverarbeitung KW - Simulation Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1397 ER - TY - JOUR A1 - Makanae, Koji T1 - Highway Sequence Editor based on the Length-based Highway Product Model N2 - The highway product model based on the length information of the centerline, and the application system is developed. This paper shows the schema and the modeling process of the product model, which includes geometric elements such as an alignment, lanes, sidewalks, shoulders and sprits, and accessories such as guard fences, plantings and signs. Furthermore, The Highway Sequence Editor (HSE) is developed as an application system to verify the model. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Straßenbau Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2347 ER - TY - JOUR A1 - Staub-French, Sheryl T1 - Feature-based Product Modeling for Building Construction N2 - Current building product models explicitly represent components, attributes of components, and relationships between components. These designer-focused product models, however, do not represent many of the design conditions that are important for construction, such as component similarity, uniformity, and penetrations. Current design and construction tools offer limited support for detecting these construction-specific design conditions. This paper describes the ontology we developed using the manufacturing concept of features to represent the design conditions that are important for construction. The feature ontology provides the blueprint for the additions and changes needed to transform a standard product model into a constructionspecific product model. The ontology formalizes three classes of features, defines the attributes and functions of each feature type, and represents the relationships between features explicitly. The descriptive semantics of the ontology allows practitioners to represent their varied preferences for naming features, specifying features that result from component intersections and the similarity of components, and grouping features that affect a specific construction domain. A software prototype that implements the ontology enables practitioners to transform designer-focused product models into feature-based product models that represent the construction perspective. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Baukonstruktion KW - Modellierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2331 ER - TY - THES A1 - Ailland, Karin T1 - Ereignisbasierte Abbildung von Bau-Ist-Zuständen N2 - Der Komplexität einer großen Baumaßnahme steht meist ein relativ unpräzises Termincontrolling gegenüber. Die Gründe dafür liegen in unzureichenden Baufortschrittsinformationen und der Schwierigkeit, eine geeignete Steuerungsmaßnahme auszuwählen. In der Folge kommt es häufig zu Terminverzügen und Mehrkosten. Ziel der Arbeit war es, die realen Bau-Ist-Zustände eines Bauprojektes so genau zu erfassen, dass es möglich wird, täglich ein zutreffendes Abbild des Baufortschrittes und der Randbedingungen des Bauablaufes zu schaffen und mit Hilfe eines Simulationswerkzeuges nachzubilden. Zu diesem Zweck sollte ein Erfassungskonzept ausgearbeitet werden, mit dessen Hilfe unter Verwendung von Erfassungstechniken aussagekräftige sowie belastbare Daten zu einer auf die Anforderungen der Simulation abgestimmten Datenbasis zusammengeführt werden. Um der Zielstellung gerecht zu werden, wurde anhand eines Beispiels ein Prozessmodell aufgebaut und definiert, welche Informationen zum Aufbau eines Simulationsmodells, das die reaktive Ablaufplanung unterstützt, erfasst werden müssen. Die einzelnen Prozessgrößen wurden detailliert beschrieben und die Erfassungsgrößen daraus abgeleitet. Weiterhin wurden Aussagen zur Prozessstrukturierung erarbeitet. Somit wurden Informationsstützstellen definiert. Es wurden Methoden zur Erfassung des Bau-Ist-Zustandes hinsichtlich ihrer Eignung sowie Anwendungsmöglichkeiten analysiert und ausgewählte Anwendungsbeispiele für RFID, Barcodes und Bautagebücher dargestellt. Außerdem wurde betrachtet, welche Daten der baustelleneigenen Bauablaufdokumentation zur Belegung der Informationsstützstellen genutzt werden können. Diese Betrachtung stellte Dokumente in den Fokus, welche aufgrund von Vorschriften oder Vertragsbedingungen ohnehin auf Baustellen erfasst werden müssen. Schließlich wurden die vorangegangenen Betrachtungen hinsichtlich der Erfassungsgrößen und der Erfassungsmethoden in einem Erfassungskonzept zusammengeführt und eine geeignete Kombination von Erfassungsmethoden entwickelt. Der Baufortschritt soll anhand der Beschreibung, welchen Status die einzelnen Vorgänge angenommen haben, mit Hilfe eines digitalen Bautagebuchs erfasst werden. Die Randbedingungen, wie die Verfügbarkeit von Personal-, Material- und Geräteressourcen, werden mit Hilfe von RFID-Tags identifiziert, auf denen alle weiteren benötigten Informationen hinterlegt sind. Informationen über Ressourcen, welche geplante Termine wiedergeben, müssen ebenfalls im digitalen Bautagebuch hinterlegt und aktuell gehalten werden. Traditionelle Lieferscheine in Papierform müssen durch digitale Lieferscheine ersetzt werden. Abgeschlossen wurde die Ausarbeitung des Erfassungskonzeptes durch Ansätze, mit deren Hilfe der Erfassungsaufwand reduziert werden kann. Zu diesem Zweck wurde eine hierarchische Ordnung des Erfassungskonzeptes eingeführt. Im Ergebnis ist somit ein Erfassungskonzept entstanden, mit dessen Hilfe die realen Bau-Ist-Zustände einer Baumaßnahme so genau erfasst werden können, dass täglich ein zutreffendes Abbild des Baufortschrittes und der Randbedingungen des Bauablaufes in einer Simulations¬umgebung generiert werden kann. Die Erfassungskonzeption liefert eine Datenbasis, die auf die Anforderungen der Simulation abgestimmt ist. T3 - Schriften der Professur Baubetrieb und Bauverfahren - 29 KW - Simulation KW - Bauprozess KW - ereignisbasiert KW - Bau-Ist Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20131029-20651 SN - 978-3-86068-508-2 PB - Verlag der Bauhaus-Universität Weimar CY - Weimar ER - TY - JOUR A1 - Alsaad, Hayder A1 - Hartmann, Maria A1 - Hilbel, Rebecca A1 - Völker, Conrad T1 - ENVI-met validation data accompanied with simulation data of the impact of facade greening on the urban microclimate JF - Data in Brief N2 - This dataset consists mainly of two subsets. The first subset includes measurements and simulation data conducted to validate the simulation tool ENVI-met. The measurements were conducted at the campus of the Bauhaus-University Weimar in Weimar, Germany and consisted of recording exterior air temperature, globe temperature, relative humidity, and wind velocity at 1.5 m at four points on four different days. After the measurements, the geometry of the campus was modelled and meshed; the simulations were conducted using the weather data of the measurements days with the aim of investigating the accuracy of the model. The second data subset consists of ENVI-met simulation data of the potential of facade greening in improving the outdoor environment and the indoor air temperature during heatwaves in Central European cities. The data consist of the boundary conditions and the simulation output of two simulation models: with and without facade greening. The geometry of the models corresponded to a residential buildings district in Stuttgart, Germany. The simulation output consisted of exterior air temperature, mean radiant temperature, relative humidity, and wind velocity at 12 different probe points in the model in addition to the indoor air temperature of an exemplary building. The dataset presents both vertical profiles of the probed parameters as well as the time series output of the five-day simulation duration. Both data subsets correspond to the investigations presented in the co-submitted article [1]. KW - Messung KW - Measurements KW - Simulations KW - ENVI-met KW - Living wall KW - Green facade KW - Simulation KW - OA-Publikationsfonds2022 Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220511-46455 UR - https://www.sciencedirect.com/science/article/pii/S2352340922004048#! VL - 2022 IS - Volume 42, article 108200 SP - 1 EP - 13 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Jentsch, Mark F. ED - Kornadt, Oliver T1 - Entwicklung eines Sommerreferenzjahres zur Bestimmung der sommerlichen Überhitzung von Gebäuden T2 - Bauphysiktage Kaiserslautern 2015, Kaiserslautern, 21-22 Oktober 2015 N2 - Die Ableitung von sommer-fokussierten warmen Referenzjahren aus langjährigen Klimadaten erfolgt in Europa bisher nach unterschiedlichen, länderspezifischen Methoden, die sich in der Regel allein auf die Trockentemperatur beziehen und in der Auswahl eines zusammenhängenden realen Sommerhalbjahres resultieren. Simulationsergebnisse zur sommerlichen Überhitzung von natürlich belüfteten Gebäuden in Deutschland und Großbritannien zeigen jedoch für einige Wetterstationen weniger Überhitzung für Simulationen mit dem sommer-fokussierten Referenzjahr als für solche mit dem entsprechenden Testreferenzjahr (TRY) für den gleichen Ort. Dies gilt insbesondere dann, wenn einzelne Monate miteinander verglichen werden. Neben der Wahl eines kompletten Halbjahres, das sowohl extrem warme als auch vergleichsweise kühle Monate beinhalten kann, liegt dies vor allem begründet in der fehlenden Berücksichtigung der Solarstrahlung bei der Auswahl eines warmen Referenzjahres, die jedoch eine wichtige Rolle für sommerliche Überhitzungserscheinungen in Gebäuden spielt. Eine verlässliche, allgemein anerkannte Methode zur Erstellung von sommer-fokussierten Referenzjahren erscheint daher auch im Hinblick auf die rechtlichen Rahmenbedingungen in der Europäischen Union, die Strategien zur natürlichen Belüftung von Neubauten und Sanierungen begünstigen, erforderlich. Diese Arbeit präsentiert einen Ansatz zur Erstellung eines Sommerreferenzjahres (Summer Reference Year – SRY) aus dem TRY eines gegebenen Ortes und langjährigen Klimadaten. Die existierenden TRY-Daten werden hierbei skaliert, um den Bedingungen für Trockentemperatur und Solarstrahlung von nah-extremen Kandidatenjahren zu entsprechen, die separat über einen statistischen Ansatz ausgewählt werden. Anschließend werden Feuchttemperatur, Windgeschwindigkeit und Luftdruck des TRY durch lineare Korrelationen mit der Trockentemperatur angepasst, um die entsprechenden SRY-Daten zu erhalten. Der Vorteil dieser Methode liegt darin, dass das grundlegende Wettermuster des TRY erhalten bleibt und somit eine klare Relation zwischen SRY und TRY besteht, die eine Vergleichbarkeit von Simulationsergebnissen gewährleistet. Über vergleichende Gebäudesimulationen mit dem zugrundeliegenden TRY und langjährigen Klimadatensätzen kann nachgewiesen werden, dass sich das SRY zur Ermittlung sommerlicher Überhitzungserscheinungen in natürlich belüfteten Gebäuden eignet. Weiterhin kann gezeigt werden, dass das SRY im Gegensatz zur direkten Nutzung eines Kandidatenjahres für einen nah-extremen Sommer die Möglichkeit eines monatsscharfen Vergleichs mit dem TRY erlaubt und frei von wenig repräsentativen Besonderheiten ist, die in den entsprechenden Kandidatenjahren vorhanden sein können. KW - Bauphysik KW - Gebäude KW - Simulation KW - Überhitzung Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170516-31058 PB - Eigenverlag der Technischen Universität Kaiserslautern CY - Kaiserslautern ER - TY - JOUR A1 - Bargstädt, Hans-Joachim A1 - Blickling, Arno T1 - Effective cost estimate and construction processes with 3D interactive technologies: Towards a virtual world of construction sites N2 - The development of 3D technologies during the last decades in many different areas, leads us towards the complete 3D representation of planet earth on a high level of detail. On the lowest level we have geographical information systems (GIS) representing the outer layer of our planet as a 3D model. In the meantime these systems do not only give a geographical model but also present additional information like ownership, infrastructure and others that might be of interest for the construction business. In future these systems will serve as basis for virtual environments for planning and simulation of construction sites. In addition to this work is done on the integration of GIS systems with 3D city models in the area of urban planning and thus integration of different levels of detail. This article presents research work on the use of 3D models in construction on the next level of detail below the level of urban planning. The 3D city model is taken as basis for the 3D model of the construction site. In this virtual nD-world a contractor can organize and plan his resources, simulate different variants of construction processes and thus find out the most effective solution for the consideration of costs and time. On the basis of former researches the authors present a new approach for cost estimation and simulation using development technologies from game software. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Baubetrieb KW - Baustelle KW - Virtuelle Realität Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2320 ER - TY - JOUR A1 - Koike, Hirotaka A1 - Morimoto, Akinori A1 - Nomura, Kazuhiro T1 - Development of Urban Land Use Model to Compare Transit-Oriented and Automobile-Oriented Cities N2 - This study is an attempt to develop a simple simulation model that can compare the differences between automobile-oriented and transit-oriented cities, and clarify the difference between city forms by transportation modes. Following a theoretical model development, a series of simulation runs are tried. The model allocates people who commute to CBD from residential zones along a transportation corridor. As a result of many simulation analyses, it is shown that automobiles need much more traffic space in comparison with the transit as is shown by the proposed traffic space ratio both in CBD and along the corridor. KW - Verkehrsplanung KW - Simulation KW - Stadtplanung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2621 ER - TY - CHAP A1 - Hoyano, Akira A1 - Nakaohkubo, Kazuaki A1 - Asawa, Takashi T1 - Development of Thermal Simulation Tool for Urban Block Design - Based on Numerical Simulation System using 3D N2 - A simulation system has been developed as a computer aided design tool to evaluate the effect of proposed design on the thermal environment during the designing process. This system calculates outdoor surface temperatures in order to evaluate the thermal impact of a design factor in outdoor space. In this study, the previous heat balance simulation system was improved to predict the surface temperature of a proposed design using 3D-CAD. This system is able to input the complicated outdoor spatial forms efficiently and also to evaluate the surface temperature distribution from any viewpoint. KW - Stadtplanung KW - Wärme KW - Simulation Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-973 ER - TY - THES A1 - Zierold, Sabine T1 - Der mediale Raum der Architektur T1 - The medial space of architecture N2 - Der architektonische Raum wird als ein Medium der Kommunikation im Kontext der >neuen< Medien begriffen, aus der Erkenntnis, dass er schon immer ein Medium war und aus einer komplexen Medienstruktur in Abhängigkeit von anderen Medien besteht. Im Prozess von Handlung und Kommunikation ist der architektonische Raum das Medium, das räumliche Nähe von Individuen über alle Sinne und das Bewusstsein gleichzeitig intensiv ermöglicht. Der architektonische Raum als immersives Kommunikationsmedium erreicht im Zeitalter der >neuen< Medien eine neue Dimension, indem mehr und andere Wirklichkeitsalternativen der Kommunikation zur Verfügung stehen. N. Luhmann folgend, wird die Architektur aus der Sicht der Form/Medium-Differenz systemtheoretisch als strukturierter Möglichkeitsraum betrachtet. Der Raum ist das Medium für Formen des architektonischen Raumes, in dem Architektur überhaupt erst wirksam wird. Umgekehrt sind die Formen des architektonischen Raumes Medien für die Wahrnehmung einer Vielzahl von räumlichen Wirklichkeiten. Eine Fassade aus Stein oder Glas ist gebaute Form und kann als Medium Information kommunizieren. Medien werden ihrer Bestimmung um so besser gerecht, je mehr sie sich der Aufmerksamkeit entziehen und wie transparente Fenster hinter der Oberfläche der sinnlichen Wahrnehmung zurücktreten. Als >unwahrnehmbares< Medium ist der architektonische Raum damit eine hintergründige >Wirkungsmacht<, eine Bühne für die Entfaltung von Wirkung, Atmosphäre und Bewegung. Seine physische Wirklichkeit war schon immer durch virtuelle Wirklichkeiten oder Realitäten entgrenzt, die durch Techniken und Technologien der Simulation als künstliche Welten wahrnehmbar und kommunizierbar werden. Dies kann an tradierten Beispielen der gotischen Kathedrale, dem Panorama, den panoptischen Räumen, dem Theater, Kino oder den kontinuierlichen Räumen von der Moderne bis heute aufgezeigt weren. Virtuelle Räume gotischer Glasbilder oder barocker Decken- und Wandbilder im Medium des architektonischen Raumes sind uns geläufig. Die Immersion, das Eintauchen in diese virtuellen Wirklichkeitsspären löst die Wahrnehmung der eigenen körperlichen Präsenz in ihnen aus. Das Potential des virtuellen Raumes der Architektur besteht im Vergleich zu anderen virtuellen Realitäten von Text, Bild oder digitalen Medien in seiner Gebundenheit an die physische, räumliche Reizstruktur, der er die Eindringlichkeit und Komplexität seiner Wirkung verdankt. Es werden unterschiedliche Wechselwirkungen und gemeinsame Entwicklungen von zeitgenössischen Beispielen der Architektur mit den >neuen< Medien aufgezeigt. In der »sensitiven Wand« wird die physische Raumgrenze durch die Integration neuer Techniken und Technologien digitaler, elektronischer Medien etwas extrem Flexibles und Formbares in Interaktion mit dem Benutzer. Der H2O Pavillon (Oosterhuis und NOX, 1997) ist ein Beispiel dafür. Der ausgeprägt polysensorische Immersionsraum steht für die Einheit von digitaler und architektonischer Simulation. Die metaphorische Welt von Höhle und Quelle des Thermalbades Vals (P.Zumthor, 1996) ist die räumliche Reflexion auf die metaphorische Struktur virtueller Räume der >neuen< Medien. Die simulierte Wirklichkeit in den Medien Wasser, Stein und architektonischer Raum produziert schöpferisch den polysensorischen immersiven Zugang in die virtuellen Welten >authentischer< physischer Umgebung. Das >Sichtbare< im Medium Raum der Architektur ist ohne das >Unsichtbare< nicht zu begreifen bzw. das sinnlich Wahrnehmbare nicht ohne das Unwahrnehmbare. Das Erkennen dieser Relation von Form und Medium ermöglicht die Formulierung des neuen Begriffes des medialen Raumes der Architektur, der zur Basis für eine Medientheorie der Architektur wird, als Sichtweise der Entgrenzung des physischen Raumes durch den virtuellen Raum für die subjektive Wahrnehmung, Handlung und Kommunikation. N2 - Within the context of the >new< media, architectonic space must be understood as a medium of communication. This is because it was always a medium, coexisting with other media within a complex media structure. Ensconced as it is within a process of activity and communication, architectonic space is the one medium that facilitates such a close proximity of individuals whose senses and consciousness thus experience a simultaneity of intensity. The architectonic space as an immersive communication medium attained a new dimension in the age of the >new< media, interactive communication availing itself of an increased number of alternative realities. Following the work of N. Luhmann, architecture may be viewed from the perspective of form/medium-difference as a structured space of possibilities within a theory of systems. The space is the medium for forms of architectonic space in the sense that only then does the architecture itself become apparent. The contrary is the case where forms of architectonic space act as media for the apperception of numerous spatial realities. A façade made of stone or glass is built form and as a medium can impart information. The more media abandon their advertence, the better they fulfil their appropriateness and recede like transparent windows behind the surface of animal consciousness. Thus, architectonic space as a >non-perceptible< medium becomes an >agent of power<, a stage for the evolvement of agency, atmosphere and movement/action. Its physical reality was always borderless, not bounded by virtual actualities or realities which are themselves perceivable and communicable as artificial worlds via the techniques and technologies of simulation. Right up to the present day, this is exemplified by artifices such as the Gothic cathedral, the panorama and panoramic spaces, the theatre, the cinema, or the continuous spaces of modernism. Virtual spaces defined by Gothic stained glass or ceiling and wall murals of the Baroque – within the medium of the architectonic space lest we forget – are all familiar to us. Immersion, in the sense of submerging in these virtual sanctums of reality, releases the apperception of each corporeal presence. In comparison to other virtual realities such as text, image or digital media, the potential of the virtual space in architecture arises out of its bondage to the physical and spatial structure of stimuli on which the forcefulness and complexity of its effectiveness depends. Citing examples of contemporary architecture points up various interdependencies between and common evolutions among the >new< media. As new techniques and technologies of digital and electronic media are introduced, the physical spatial border of the >sensitive wall< becomes in terms of interaction increasingly pliable and ductile for the user. The H2O Pavilion (Oosterhuis and NOX, 1997) is just one example. The highly polysensoric immersion space stands for the unity of digital and architectonic simulation. The metaphoric world of caverns and wells of the hot springs at Vals (P. Zumthor, 1996) is the spatial reflexion on the metaphoric structure of virtual spaces as exemplified by the >new< media. The simulated reality in the media water, stone, and architectonic space, enables in an inventive way the polysensoric and immersive access to the virtual worlds of the >authentic< physical environment. That which is >visible< in the medium of architectural space is not understandable without the >invisible<; in other words, the state of sensory perceptibility depends on the existence of the non-perceptible. The recognition of this relation between form and medium allows a new term to be formulated: the >medial space of architecture<. This in turn becomes the basis for a new media theory of architecture itself, a premise defined as a perspective on the debordering of physical space through the virtual one and existing to provide subjective apperception, activity and communication. KW - Architektur KW - Medium KW - Form KW - Bauform KW - Raumwahrnehmung KW - Simulation KW - Imagination KW - Kommunikation KW - Immersion KW - Illusion KW - architektonischer Raum KW - Virtualität KW - architectural space KW - virtuality Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20060806-8106 ER - TY - JOUR A1 - Alsaad, Hayder A1 - Völker, Conrad T1 - Der Kühlungseffekt der personalisierten Lüftung T1 - The cooling effect of personalized ventilation systems JF - Bauphysik N2 - Personalisierte Lüftung (PL) kann die thermische Behaglichkeit sowie die Qualität der eingeatmeten Atemluft verbessern, in dem jedem Arbeitsplatz Frischluft separat zugeführt wird. In diesem Beitrag wird die Wirkung der PL auf die thermische Behaglichkeit der Nutzer unter sommerlichen Randbedingungen untersucht. Hierfür wurden zwei Ansätze zur Bewertung des Kühlungseffekts der PL untersucht: basierend auf (1) der äquivalenten Temperatur und (2) dem thermischen Empfinden. Grundlage der Auswertung sind in einer Klimakammer gemessene sowie numerisch simulierte Daten. Vor der Durchführung der Simulationen wurde das numerische Modell zunächst anhand der gemessenen Daten validiert. Die Ergebnisse zeigen, dass der Ansatz basierend auf dem thermischen Empfinden zur Evaluierung des Kühlungseffekts der PL sinnvoller sein kann, da bei diesem die komplexen physiologischen Faktoren besser berücksichtigt werden. N2 - Personalized ventilation (PV) can improve thermal comfort and inhaled air quality by supplying air to each workstation separately. This study investigates the impact of PV on the thermal state of the users under summer boundary conditions. Two approaches to evaluating the cooling effect of PV were investigated, based on equivalent temperature and based on thermal sensation. Both approaches implemented measured and simulated values of the cooling effect of PV. Before conducting the simulations, the numerical model was first validated against measured data collected in a climate chamber equipped with a thermal manikin. Results indicated that the thermal sensation approach can be more suitable for evaluating the cooling effect of PV due to the complex physiological factors it considers. KW - Lüftung KW - Strömung KW - Raumklima KW - Temperatur KW - personalized ventilation KW - computational fluid dynamics KW - Simulation KW - personalisierte Lüftung KW - äquivalente Temperatur KW - thermisches Empfinden Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20201020-42723 UR - https://onlinelibrary.wiley.com/doi/abs/10.1002/bapi.202000018 N1 - © 2020 Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG, Berlin. Dieser Artikel kann für den persönlichen Gebrauch heruntergeladen werden. Andere Verwendungen bedürfen der vorherigen Zustimmung der Autoren und des Verlags Ernst & Sohn. Der folgende Artikel erschien in der Bauphysik 42 (2020), Heft 5, 218-225, DOI: 10.1002/bapi.202000018 VL - 2020 IS - volume 42, issue 5 SP - 218 EP - 225 PB - Ernst & Sohn bei John Wiley & Sons CY - Hoboken ER - TY - CHAP A1 - Bargstädt, Hans-Joachim A1 - Ailland, Karin T1 - CONVR 2011 : Proceedings of the 11th International Conference on Construction Applications of Virtual Reality N2 - Proceedings of the 11th International Conference on Construction Applications of Virtual Reality T3 - Schriften der Professur Baubetrieb und Bauverfahren - 21 KW - Plant Simulation KW - Simulation KW - Virtuelle Realität KW - Visualisierung KW - Informationssystem KW - Design visualization KW - Construction visualization KW - Building information modelling KW - Simulation in construction KW - Virtual reality Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111102-15603 SN - 978-3-86068-458-0 ER - TY - THES A1 - Salzmann, Holger T1 - Collaboration in Co-located Automotive Applications N2 - Virtual reality systems offer substantial potential in supporting decision processes based purely on computer-based representations and simulations. The automotive industry is a prime application domain for such technology, since almost all product parts are available as three-dimensional models. The consideration of ergonomic aspects during assembly tasks, the evaluation of humanmachine interfaces in the car interior, design decision meetings as well as customer presentations serve as but a few examples, wherein the benefit of virtual reality technology is obvious. All these tasks require the involvement of a group of people with different expertises. However, current stereoscopic display systems only provide correct 3D-images for a single user, while other users see a more or less distorted virtual model. This is a major reason why these systems still face limited acceptance in the automotive industry. They need to be operated by experts, who have an advanced understanding of the particular interaction techniques and are aware of the limitations and shortcomings of virtual reality technology. The central idea of this thesis is to investigate the utility of stereoscopic multi-user systems for various stages of the car development process. Such systems provide multiple users with individual and perspectively correct stereoscopic images, which are key features and serve as the premise for the appropriate support of collaborative group processes. The focus of the research is on questions related to various aspects of collaboration in multi-viewer systems such as verbal communication, deictic reference, embodiments and collaborative interaction techniques. The results of this endeavor provide scientific evidence that multi-viewer systems improve the usability of VR-applications for various automotive scenarios, wherein co-located group discussions are necessary. The thesis identifies and discusses the requirements for these scenarios as well as the limitations of applying multi-viewer technology in this context. A particularly important gesture in real-world group discussions is referencing an object by pointing with the hand and the accuracy which can be expected in VR is made evident. A novel two-user seating buck is introduced for the evaluation of ergonomics in a car interior and the requirements on avatar representations for users sitting in a car are identified. Collaborative assembly tasks require high precision. The novel concept of a two-user prop significantly increases the quality of such a simulation in a virtual environment and allows ergonomists to study the strain on workers during an assembly sequence. These findings contribute toward an increased acceptance of VR-technology for collaborative development meetings in the automotive industry and other domains. N2 - Virtual-Reality-Systeme sind ein innovatives Instrument, um mit Hilfe computerbasierter Simulationen Entscheidungsprozesse zu unterstützen. Insbesondere in der Automobilbranche spielt diese Technologie eine wichtige Rolle, da heutzutage nahezu alle Fahrzeugteile in 3D konstruiert werden. Im Entwicklungsbereich der Automobilindustrie werden Visualisierungssysteme darüber hinaus bei der Untersuchung ergonomischer Aspekte von Montagevorgängen, bei der Bewertung der Mensch-Maschine-Schnittstelle im Fahrzeuginterieur, bei Designentscheidungen sowie bei Kundenpräsentationen eingesetzt. Diese Entscheidungsrunden bedürfen der Einbindung mehrerer Experten verschiedener Fachbereiche. Derzeit verfügbare stereoskopische Visualisierungssysteme ermöglichen aber nur einem Nutzer eine korrekte Stereosicht, während sich für die anderen Teilnehmer das 3D-Modell verzerrt darstellt. Dieser Nachteil ist ein wesentlicher Grund dafür, dass derartige Systeme bisher nur begrenzt im Automobilbereich anwendbar sind. Der Fokus dieser Dissertation liegt auf der Untersuchung der Anwendbarkeit stereoskopischer Mehrbenutzer-Systeme in verschiedenen Stadien des automobilen Entwicklungsprozesses. Derartige Systeme ermöglichen mehreren Nutzern gleichzeitig eine korrekte Stereosicht, was eine wesentliche Voraussetzung für die Zusammenarbeit in einer Gruppe darstellt. Die zentralen Forschungsfragen beziehen sich dabei auf die Anforderungen von kooperativen Entscheidungsprozessen sowie den daraus resultierenden Aspekten der Interaktion wie verbale Kommunikation, Gesten sowie virtuelle Menschmodelle und Interaktionstechniken zwischen den Nutzern. Die Arbeit belegt, dass stereoskopische Mehrbenutzersysteme die Anwendbarkeit virtueller Techniken im Automobilbereich entscheidend verbessern, da sie eine natürliche Kommunikation zwischen den Nutzern fördern. So ist die Unterstützung natürlicher Gesten beispielsweise ein wichtiger Faktor und es wird dargelegt, welche Genauigkeit beim Zeigen mit der realen Hand auf virtuelle Objekte erwartet werden kann. Darüber hinaus werden Anforderungen an virtuelle Menschmodelle anhand einer Zweibenutzer-Sitzkiste identifiziert und untersucht. Diese Form der Simulation, bei der die Nutzer nebeneinander in einem Fahrzeugmodell sitzen, dient vor allem der Bewertung von Mensch-Maschine-Schnittstellen im Fahrzeuginterieur. Des Weiteren wird das neue Konzept eines Mehrbenutzer-Werkzeugs in die Arbeit mit einbezogen, da hier verdeutlicht wird wie die Simulation von Montagevorgängen in virtuellen Umgebungen mit passivem haptischem Feedback zu ergonomischen Verbesserungen entsprechender Arbeitsvorgänge in der Realität beitragen kann. Diese Konzepte veranschaulichen wie VR-Systeme zur Unterstützung kollaborativer Prozesse in der Automobilbranche und darüber hinaus eingesetzt werden können. T2 - Zusammenarbeit in virtuellen Gruppenszenarien in der automobilen Entwicklung KW - Virtuelle Realität KW - Immersion KW - Simulation KW - Computergraphik KW - Virtual Reality KW - Computer Graphics KW - Interaction Techniques KW - Collaboration Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20100712-15102 ER - TY - JOUR A1 - Kang, Shihchung A1 - Miranda, Eduardo T1 - Automated Simulation of the Erection Activities in Virtual Construction N2 - The goal of the research is the development of a computer system to plan, simulate and visualize erection processes in construction. In the research construction cranes are treated as robots with predefined degrees of freedom and crane-specific motion planning techniques are developed to generate time-optimized and collision-free paths for each piece to be erected in the project. Using inverse kinematics and structural dynamics simulation, the computer system then computes the crane motions and velocities necessary to achieve the previously calculated paths. The main benefits of the research are the accurate planning and scheduling of crane operations leading to optimization of crane usage and project schedules, as well as improving overall crane safety in the project. This research is aimed at the development of systems that will allow computer-assisted erection of civil infrastructure and ultimately to achieve fully-automated erection processes using robotic cranes... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Baukonstruktion KW - Virtuelle Realität Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2310 ER - TY - THES A1 - Dang, Trang T1 - Automated Detailing of 4D Schedules N2 - The increasing success of BIM (Building Information Model) and the emergence of its implementation in 3D construction models have paved a way for improving scheduling process. The recent research on application of BIM in scheduling has focused on quantity take-off, duration estimation for individual trades, schedule visualization, and clash detection. Several experiments indicated that the lack of detailed planning causes about 30% non-productive time and stacking of trades. However, detailed planning still has not been implemented in practice despite receiving a lot of interest from researchers. The reason is associated with the huge amount and complexity of input data. In order to create a detailed planning, it is time consuming to manually decompose activities, collect and calculate the detailed information in relevant. Moreover, the coordination of detailed activities requires much effort for dealing with their complex constraints. This dissertation aims to support the generation of detailed schedules from a rough schedule. It proposes a model for automated detailing of 4D schedules by integrating BIM, simulation and Pareto-based optimization. T3 - Schriften der Professur Baubetrieb und Bauverfahren - 32 KW - BIM KW - Simulation KW - Pareto optimization KW - multi-objective optimization KW - scheduling Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20141006-23103 ER - TY - INPR A1 - Rezakazemi, Mashallah A1 - Mosavi, Amir A1 - Shirazian, Saeed T1 - ANFIS pattern for molecular membranes separation optimization N2 - In this work, molecular separation of aqueous-organic was simulated by using combined soft computing-mechanistic approaches. The considered separation system was a microporous membrane contactor for separation of benzoic acid from water by contacting with an organic phase containing extractor molecules. Indeed, extractive separation is carried out using membrane technology where complex of solute-organic is formed at the interface. The main focus was to develop a simulation methodology for prediction of concentration distribution of solute (benzoic acid) in the feed side of the membrane system, as the removal efficiency of the system is determined by concentration distribution of the solute in the feed channel. The pattern of Adaptive Neuro-Fuzzy Inference System (ANFIS) was optimized by finding the optimum membership function, learning percentage, and a number of rules. The ANFIS was trained using the extracted data from the CFD simulation of the membrane system. The comparisons between the predicted concentration distribution by ANFIS and CFD data revealed that the optimized ANFIS pattern can be used as a predictive tool for simulation of the process. The R2 of higher than 0.99 was obtained for the optimized ANFIS model. The main privilege of the developed methodology is its very low computational time for simulation of the system and can be used as a rigorous simulation tool for understanding and design of membrane-based systems. Highlights are, Molecular separation using microporous membranes. Developing hybrid model based on ANFIS-CFD for the separation process, Optimization of ANFIS structure for prediction of separation process KW - Fluid KW - Simulation KW - Molecular Liquids KW - optimization KW - machine learning KW - Membrane contactors KW - CFD Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20181122-38212 N1 - This is the pre-peer reviewed version of the following article: https://www.sciencedirect.com/science/article/pii/S0167732218345008, which has been published in final form at https://doi.org/10.1016/j.molliq.2018.11.017. VL - 2018 SP - 1 EP - 20 ER - TY - JOUR A1 - van Treeck, Christoph A1 - Rank, Ernst T1 - Analysis of building structure and topology based on Graph Theory N2 - Individual views on a building product of people involved in the design process imply different models for planning and calculation. In order to interpret these geometrical, topological and semantical data of a building model we identify a structural component graph, a graph of room faces, a room graph and a relational object graph as aids and we explain algorithms to derive these relations. The application of the technique presented is demonstrated by the analysis and discretization of a sample model in the scope of building energy simulation. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Graphentheorie KW - Ingenieurbau Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2308 ER - TY - CHAP A1 - Fahrig, Torsten A1 - Nachtwey, Björn A1 - Gellert, Sebastian T1 - A Product Model based Approach to Interactive CAE Design Optimization N2 - We present a software prototype for fluid flow problems in civil engineering, which combines essential features of Computational Steering approaches with efficient methods for model transfer and high performance computing. The main components of the system are described: - The modeler with a focus on the data management of the product model - The pre-processing and the post-processing toolkit - The simulation kernel based on the Lattice Boltzmann method - The required hardware for real-time computing KW - Produktmodell KW - Simulation KW - Bautechnik KW - Entwurf KW - Optimierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1901 ER -