TY - JOUR A1 - Krebs, F. A1 - Brück, E. T1 - 3D-Computergrafik und -animation als Instrument der Visualisierung im Bereich Entwurf und Denkmalpflege N2 - Seit mehreren Jahren wird im Fachbereich Gestaltung, Studiengang Innenarchitektur 3D-Computergrafik und -animation in Lehrveranstaltungen ausgebildet und in Projekt- und Diplomarbeiten als Darstellungsmedium angewandt. Eine besondere Herausforderung stellen dabei die 3D-Visualisierungen von historischen Gebäuden dar. Mit den beiden nachfolgenden Beispielen soll der Einsatz und die curricularen Verknüpfung der CA-Technologie mit Studienarbeiten und Projekten zum Thema >Denkmalpflege< aufgezeigt werden. Rekonstruktion und Visualisierung des ehemaligen >Jagdschlosses Platte< bei Wiesbaden. Mit Unterstützung einer Kunsthistorikerin wurde in einer Studienarbeit das im Krieg zerstörte ehemalige Jagdschloß im Computer nachgebildet. Neben der Darstellung des Gebäudeäußeren und des zentralen Innenbereiches wurde eine Animation über die Triangulierung der klassizistischen Geometrie erstellt. Umnutzung historischer Bausubstanz am Beispiel der ehemaligen Klostersanlage >Schiffenberg< bei Gießen. Im Rahmen einer Projektarbeit wurden mehrer Konzepte entwickelt, Entwürfe erstellt und mittels Computeranimationen öffentlich präsentiert. In Kooperation mit dem Studiengang Fernsehtechnik (FH-Wiesbaden) wurde von zwei Studenten eine Videodokumentation über den gesamten Projektverlauf erstellt. Neben dem Aufzeigen der Arbeitsprozesse und dem Vorstellen des Lehrkonzeptes für die curriculare Einbindung der CA-Technologie werden aktuelle Studienergebnisse anhand von Videoprojektionen vorgestellt. KW - Architektur KW - Visualisierung KW - Dreidimensionales Modell KW - Computergraphik Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5235 ER - TY - JOUR A1 - Noh, Jung-Hwi A1 - Park, Jong-Heon T1 - A Calculation of Initial Cable Force for Ko-Ha Grand Bridge N2 - The primary objective of initial shape analysis of a cable stayed bridge is to calculate initial installation cable tension forces and to evaluate fabrication camber of main span and pylon providing the final longitudinal profile of the bridge at the end of construction. In addition, the initial cable forces depending on the alternation of the bridge’s shape can be obtained from the analysis, and will be used to provide construction safety during construction. In this research, we conducted numerical experiments for initial shape of Ko-ha bridge, which will be constructed in the near future, using three different typical methods such as continuous beam method, linear truss method, and IIMF (Introducing Initial Member Force) method KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Hängebrücke KW - cable stayed bridge KW - cable force KW - initial shape KW - initial equilibrium state Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2459 ER - TY - JOUR A1 - Vaarmann, Otu T1 - A class of rapidly convergent interative Methods for Problems in mathematical Modelling N2 - Methods with the convergence order p 2 (Newton`s, tangent hyperbolas, tangent parabolas etc.) and their approximate variants are studied. Conditions are presented under which the approximate variants preserve their convergence rate intrinsic to these methods and some computational aspects (possibilities to organize parallel computation, globalization of a method, the solution of the linear equations versus the matrix inversion at every iteration etc.) are discussed. Polyalgorithmic computational schemes (hybrid methods) combining the best features of various methods are developed and possibilities of their application to numerical solution of two-point boundary-value problem in ordinary differential equations and decomposition-coordination problem in convex programming are analyzed. KW - Mathematisches Modell KW - Dialogsystem Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5223 ER - TY - JOUR A1 - Beer, Daniel G. A1 - Firmenich, Berthold A1 - Richter, Torsten T1 - A Concept for CAD Systems with Persistent Versioned Data Models N2 - The synchronous distributed processing of common source code in the software development process is supported by well proven methods. The planning process has similarities with the software development process. However, there are no consistent and similarly successful methods for applications in construction projects. A new approach is proposed in this contribution. KW - Produktmodell KW - Bautechnik KW - Forschungskooperation KW - Versionsverwaltung KW - CAD Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2046 ER - TY - JOUR A1 - Ma, Zhiliang A1 - Qin, Liang T1 - A Framework of Management Information System for Construction Projects N2 - A comprehensive framework of information management system for construction projects in China has been established through extensive literature survey and field investigation. It utilizes the potential information technologies and covers the practical management patterns as well as the major aspects of construction project management. It can be used to guide and evaluate the design of the information management systems for construction projects in order to make the system to be applicable to a wide variety of construction projects and survive the changes in project management. KW - Mehragentensystem KW - Lernendes System KW - Managementinformationssystem Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2126 ER - TY - JOUR A1 - El-Rayes, Khaled A1 - Hyari, Khalied T1 - A Multi-objective Model for Optimizing Construction Planning of Repetitive Infrastructure Projects N2 - This paper presents the development of a model for optimizing resource utilization in repetitive infrastructure projects. The model provides the capability of simultaneous minimization of both project duration and work interruptions for construction crews. The model provides in a single run, a set of nondominated solutions that represent the tradeoff between these two objectives. The model incorporates a multiobjective genetic algorithm and scheduling algorithm. The model initially generates a randomly selected set of solutions that evolves to a near optimal set of tradeoff solutions in subsequent generations. Each solution represents a unique scheduling solution that is associated with certain project duration and a number of interruption days for utilized construction crews. As such, the model provides project planners with alternative schedules along with their expected duration and resource utilization efficiency. KW - Mehragentensystem KW - Lernendes System KW - Infrastruktur Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2135 ER - TY - JOUR A1 - Foorgber, U. A1 - Müller, Christian T1 - A Planning Process Model for Computer Supported Cooperative Work in Building Construction N2 - Increasing complexity of today's buildings requires a high level of integration in the planning process. Common planning strategies, where individual project partners cooperate mainly to exchange results, are not suitable to jointly develop project goals and objectives. Integrated planning, a more holistic approach to deal with complex problems, is based on a high degree of communication amoung team members and leads to a goal oriented cooperation. Current approaches in the reasearch area of Computer Supported Cooperative Work (CSCW) poorly meet the requirements in planning. A planning process model, based on the principles of integrated planning will be introduced, aimed to provide the background for the implementation of a CSCW-platform. KW - Bauwesen KW - Integrierte Planung KW - Computer Supported Cooperative Work Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4922 ER - TY - JOUR A1 - Mironov, Vadim A1 - Pahl, Peter Jan T1 - A Prismatic Finite Element for Accurate Arch Dam Analysis N2 - The displacements and stresses in arch dams and their abutments are frequently determined with 20-node brick elements. The elements are distorted near the contact plane between the wall and the abutment. A cantilever beam testbed has been developed to investigate the consequences of this distortion. It is shown that the deterioration of the accuracy in the computed stresses is significant. A compatible 18-node wedge element with linear stress variation is developed as an alternative to the brick element. The shape of this element type is readily adapted to the shape of the contact plane. It is shown that the accuracy of the computed stresses in the vicinity of the contact plane is improved significantly by the use of wedge elements. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Dammbau Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2467 ER - TY - JOUR A1 - Rebolj, D. T1 - A Product Model of a Road N2 - Many errors and delays frequently appear when data is exchanged between particular tasks in the lifecycle of the road. Inter-task connections are therefore of great importance for the quality of the final product. The article describes a product model of a road wich is the kernel of an integrated information system intended to support all important stages of the road lifecycle: design, evaluation (through different analysis procedures), construction, and maintainance. Since particular tasks are often executed at different places and in different companies, the interconnections are supported by a special metafile which contains all specific data of the product model. The concept of the integrated system is object and component oriented. Additionally, existing conventional program packages are included to support some common tasks (methods). A conventional relational database system as well as an open spatial database system with the relevant GIS functionality are included to support the data structures of the model. KW - Straße KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4584 ER - TY - JOUR A1 - Yabuki, Nobuyoshi A1 - Kotani, Jun A1 - Shitani, Tomoaki T1 - A Steel Bridge Design System Architecture using VR-CAD and Web Service-based Multi-Agents N2 - This paper presents a new design environment based on Multi-Agents and Virtual Reality (VR). In this research, a design system with a virtual reality function was developed. The virtual world was realized by using GL4Java, liquid crystal shutter glasses, sensor systems, etc. And the Multi-Agent CAD system with product models, which had been developed before, was integrated with the VR design system. A prototype system was developed for highway steel plate girder bridges, and was applied to a design problem. The application verified the effectiveness of the developed system. KW - Mehragentensystem KW - Lernendes System KW - Stahlbrücke KW - Virtuelle Realität Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2146 ER - TY - JOUR A1 - Koike, Hirotaka A1 - Morimoto, Akinori A1 - Imamura, Maki T1 - A Study on the Relationships of Residential Electricity Consumption and Automobile Energy Consumption with Urban Forms Using GIS N2 - In this Paper, we explored the relation between the electricity consumption in residential sector and the automobile energy consumption in transportation sector in accordance with the location of city by employing Geographic Information System (GIS). We found in the study that the electricity consumption per capita has a tendency that is higher in city center and lower in suburbs in Utsunomiya city. It is also noted that there is little difference among total consumption between city center and suburbs, despite the fact that the density of electric appliances tends to increase in a small size house of city center and the amount of automobile energy consumption from residence is lower in city center than in suburbs. KW - Geoinformationssystem KW - Stadtplanung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2690 ER - TY - JOUR A1 - Huhn, Michael T1 - Abstract and Concrete Scenarios in Concurrent Engineering N2 - An architecture of a distributed planning system for the building industry has been developed. The emphasis is on highly collaborative environments in steelwork, timber construction etc. where designers concurrently handle 3D models. The overall system connects local design systems by the so-called Design Framework DFW. This framework consists of the definition of distributed components and protocols which make the collaborative design work. The process of collaborative design has been formalized on an abstract level. This paper describes how this has been done. A sample is given to illustrate the mapping of concrete scenarios of the ‘real design world’ to an abstract scenario level. This work is funded by the Deutsche Forschungsgemeinschaft DFG as part of the project SPP1103 (Meißner et al. 2003). KW - Produktmodell KW - Bautechnik KW - Forschungskooperation KW - Framework Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2068 ER - TY - JOUR A1 - Albert, Andrej A1 - Freischlad, Mark A1 - Pullmann, Torben T1 - Acquisition of Conceptual Design Knowledge in Structural Engineering N2 - Expert systems integrating fuzzy reasoning techniques represent a powerful tool to support practicing engineers during the early stages of structural design. In this context fuzzy models have proved themselves to be very suitable for the representation of complex design knowledge. However their definition is a laborious task. This paper introduces an approach for the design and the optimization of fuzzy systems based upon Genetic Programming. To keep the emerging fuzzy systems transparent a new framework for the definition of linguistic variables is also introduced. KW - Mehragentensystem KW - Lernendes System KW - Wissensverarbeitung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2154 ER - TY - JOUR A1 - Lee, Kangkun A1 - Lee, Kijang T1 - Additional bending moment for shear-lag phenomenon in tube structures N2 - Framed-tube system with multiple internal tubes is analysed using an orthotropic box beam analogy approach in which each tube is individually modelled by a box beam that accounts for the flexural and shear deformations, as well as the shear-lag effects. A simple numerical modeling technique is proposed for estimating the shear-lag phenomenon in tube structures with multiple internal tubes. The proposed method idealizes the framed-tube structures with multiple internal tubes as equivalent multiple tubes, each composed of four equivalent orthotropic plate panels. The numerical analysis is based on the minimum potential energy principle in conjunction with the variational approach. The shear-lag phenomenon of such structures is studied taking into account the additional bending moments in the tubes. A detailed work is carried out through the numerical analysis of the additional bending moment. The moment factor is further introduced to identify the shear lag phenomenon along with the additional moment. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Hochhaus Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2472 ER - TY - JOUR A1 - Berkowski, P. A1 - Boron, Jacek T1 - An Algorithm of compromise structural Optimisation of Bar Structures N2 - Authors' own research in applied unicriterial and multicriterial optimisation of bar structures, and also an analysis of accessible bibliography on structural synthesis allows to present herein an attempt to define a general algorithm for proceeding in formulation of a structural optimisation problem. A practical aspect of such an algorithm consists, in author's opinion, in enabling a designer a correct creation of a mathematical model of synthesis problems, independently of known mathematical methods employed to looking for an unconditional extremum of function of several variables. A proposed algorithm is not a ready-for-use tool for solving all the optimisation problems, but it constitutes an easy-to-expand theoretical basis. This basis should allow a designer to create a proper set of compromises on the way to construct a mathematical model of a specific optimisation problem. The algorithm, presented in the paper, is constructed as a sequence of the one-after-another problem questions, on which the designer answers: yes or no, and a set of selections from the knowledge base consisting of the elements of an optimisation problem components. The order of making questions adopted by the authors in the algorithm is subjective, however it is supported by their experience, both in applied optimisation and in designing of structures like trusses or frames. KW - Stabwerk KW - Optimierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5264 ER - TY - JOUR A1 - Yabuki, Nobuyoshi A1 - Yoshimura, Yutaka T1 - An Evaluation System for Steel Structures of Hydroelectric Power Stations based on Fault Tree Analysis and Performance Maps N2 - This paper presents an evaluation system for steel structures of hydroelectric power stations, including hydraulic gates and penstocks, based on Fault Tree Analyasis (FTA) and performance maps. This system consists of fault tree diagrams of FTA, performance maps, design and analysis systems, and engineerin databases. These four modules are integrated by appropriate hyperlinks so that the user of this system can use it easily and seamlessly. A well developed system was applied to some illustrative example cases, and they showed that the developed methodology and system worked well and the users found the system useful and effective for their maintenance tasks at powerstations. KW - Wissensmanagement KW - Stahlbau KW - Wasserkraftwerk Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2564 ER - TY - JOUR A1 - van Treeck, Christoph A1 - Rank, Ernst T1 - Analysis of building structure and topology based on Graph Theory N2 - Individual views on a building product of people involved in the design process imply different models for planning and calculation. In order to interpret these geometrical, topological and semantical data of a building model we identify a structural component graph, a graph of room faces, a room graph and a relational object graph as aids and we explain algorithms to derive these relations. The application of the technique presented is demonstrated by the analysis and discretization of a sample model in the scope of building energy simulation. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Graphentheorie KW - Ingenieurbau Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2308 ER - TY - JOUR A1 - Misztal, S. A1 - Misztal, G. T1 - Anwendung von Delta-Dirac-Funktion und Heviside-Funktion zur Berechnung der inneren Kräfte und Verschiebungen in gebogenen Balken N2 - Die d - Dirac - Funktion d(x-xi) und Heviside - Funktion wurden vor allem zur Beschreibung diskontinuierlicher Belastungsfunktionen von gebogenen Balken angewendet. Im Referat werden die mathematischen Operationen auf den erwähnten Funktionen dargestellt. Darüber hinaus wird die Möglichkeit eindeutiger Aufschreibung von belibigen Belestungsfunktionen vorgeschlagen, die fast alle Fälle der in der Ingenieurpraxis auftretenden Belastungen umfassen. Die vorgeschlagenen Lösungen geben die Möglichkeit leichter Aufschreibung im Form eines Algorithmus, das die Ausnutzung von Komputertechnik in statischen Berechnungen ermöglicht. Am Ende des Referates werden die Zahlebeispiele dargestellt, die die Möglichkeiten praktischer Anwendungen der besprochenen Funktionen darstellen. KW - Balken KW - Belastung KW - Mathematisches Modell KW - Computerunterstütztes Verfahren Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5308 ER - TY - JOUR A1 - Chang, Chihyuan A1 - Chang, Yuanchu A1 - Huang, Shyhmeng T1 - Application of a Agent Mechanism to the Small-scale Maintenance of School Buildings N2 - This paper presents an agent-based software, Virtual Administrator System (VAS) for the smallscale maintenance of school buildings. VAS is capable of handling a heavy load of routine, lowtech maintenance jobs. It assigns a different priority to each job application according to its significance and urgency, and automatically adjusts schedules for maintenance engineers when on-site supervision is needed. The system can help ease off the burden of routine small-scale maintenance work, making it more cost-effective and efficient in the overall management of school building maintenance. VAS posts jobs on the Web in a multi-media format and classified all applications into four categories: the on-call maintenance contract, the term maintenance contract, the guaranty maintenance contract, and the regular maintenance contract. It then estimates their urgency level and passes the information to maintenance engineers who will decide whether on-site inspection is needed. Based on the engineers’ feedback, VAS automatically implements the scheduling for inspection as well as sends out real-time or batch notifications to contractors. All these activities are recorded in a database to allow continuous research and data mining and the analysis and diagnosis of specific jobs for followup maintenance plans. KW - Mehragentensystem KW - Lernendes System KW - Schulgebäude KW - Facility-Management Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2165 ER - TY - JOUR A1 - Most, Thomas A1 - Eckardt, Stefan T1 - Application of a hybrid parallelization technique to accelerate the numerical simulation of nonlinear mechanical problems N2 - This paper presents the combination of two different parallelization environments, OpenMP and MPI, in one numerical simulation tool. The computation of the system matrices and vectors is parallelized with OpenMP and the solution of the system of equations is done with the MPIbased solver MUMPS. The efficiency of both algorithms is shown on several linear and nonlinear examples using the Finite Element Method and a meshless discretization technique. KW - Framework KW - API KW - Parallelverarbeitung KW - Finite-Elemente-Methode Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2599 ER - TY - JOUR A1 - Melnikov, B. E. A1 - Semenov, Artem T1 - Application of Multimodel Method of Elasto-Plastic Analysis for the Multilevel Computation of Structures N2 - Creation of hierarchical sequence of the plastic and viscoplastic models according to different levels of structure approximations is considered. Developed strategy of multimodel analysis, which consists of creation of the inelastic models library, determination of selection criteria system and caring out of multivariant sequential clarifying computations, is described. Application of the multimodel approach in numerical computations has demonstrated possibility of reliable prediction of stress-strain response under wide variety of combined nonproportional loading. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Elastoplastizität Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2487 ER - TY - JOUR A1 - Kang, Shihchung A1 - Miranda, Eduardo T1 - Automated Simulation of the Erection Activities in Virtual Construction N2 - The goal of the research is the development of a computer system to plan, simulate and visualize erection processes in construction. In the research construction cranes are treated as robots with predefined degrees of freedom and crane-specific motion planning techniques are developed to generate time-optimized and collision-free paths for each piece to be erected in the project. Using inverse kinematics and structural dynamics simulation, the computer system then computes the crane motions and velocities necessary to achieve the previously calculated paths. The main benefits of the research are the accurate planning and scheduling of crane operations leading to optimization of crane usage and project schedules, as well as improving overall crane safety in the project. This research is aimed at the development of systems that will allow computer-assisted erection of civil infrastructure and ultimately to achieve fully-automated erection processes using robotic cranes... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Baukonstruktion KW - Virtuelle Realität Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2310 ER - TY - JOUR A1 - Erlemann, Kai T1 - BABSIM - An object-oriented software framework for microscopic simulation of freeway traffic N2 - A wide variety of behavioural models exist in microscopic traffic simulation. Commercial programms often use closed-source policies and are confined to their respective simulation platforms. Open-source approaches mainly focus on distinctive, highly specialized traffic situations. In the scope of this paper, an open-source framework for developing modular, objectoriented simulation systems is presented, capable of simultaneously accommodating different driving models and enabling the user to modify and extend the catalogue of driving behaviours. The existing driving behaviours and the computational implementation of the simulation are being described. KW - Framework KW - API KW - Verkehrsplanung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2601 ER - TY - JOUR A1 - Peters, F. A1 - Petersen, Michael A1 - Meißner, Udo F. T1 - Bestandsverwaltung und -bewirtschaftung durch integratives Informationsmanagement N2 - Neben der reinen Bauausführung und den damit verbundenen Roh- und Ausbaukosten stellt insbesondere die Bewirtschaftung von Gebäuden einen wesentlichen Kostenfaktor dar, den zu minimieren Ziel der Bestrebungen auf dem Gebiet des Facilities Management ist. Insbesondere die Integration der verteilt vorliegenden Informationen muß hierbei das Ziel sein, um durch effiziente Informationsverarbeitung eine Einsparung von Unterhaltskosten zu erreichen. Bereits in der Planungsphase lassen sich die späteren Kosten für die Bewirtschaftung modellieren. Dies gilt auch für die Modellierung des Energiehaushaltes von Gebäuden. Für die Modellierung des Wärmeschutzes und der damit verbundenen Ermittlung des Heizenergiebedarfs werden z.Zt. starke Vereinfachungen getroffen, die durch die aktuelle Wärmeschutzverordnung vorgegeben sind, so daß die errechneten Werte meist sehr ungenau sind. Für eine DV-gerechte Modellierung eines Gebäudes während seiner Bewirtschaftung reichen herkömmliche CAD-Systeme nicht aus, da das Modell verschiedene Sichten zulassen muß: Neben einer bauteilorientierten Sicht muß auch eine raumorientierte Sicht vorgehalten werden, damit eine Modellierung von flächenbezogenen Parametern wie z.B. Kosten möglich wird. Dieser Beitrag zeigt einen Ansatz, der eine intensive Nutzung heterogener Ressourcen und Informationen auf der Grundlage eines dreidimensionalen Gebäudemodells ermöglicht. Exemplarisch für die Bereiche Raummanagement (im Sinne von kosten- und nutzungsorientierter Bestandsverwaltung) und Bauphysik wird dieser Ansatz erläutert und die Eingliederung dieser Teilgebiete der Bestandsverwaltung und -bewirtschaftung in ein Gesamtsystem aufgezeigt. KW - Bauwerk KW - Langzeitverhalten KW - Facility-Management KW - Informationsmanagement Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4848 ER - TY - JOUR A1 - Ngo, D. Q. A1 - Rüppel, Uwe T1 - BINAS - Ein Entscheidungshilfesystem für die Bestandsanalyse von Bauwerken N2 - Bauwerke sind in ihrer Betriebszeit vielen nutzungseinschränkenden Einflüssen ausgesetzt. Die dadurch erforderliche Instandhaltung dient zur Gewährleistung und zur Erhöhung der geplanten Nutzungsfähigkeit sowie Dauerhaftigkeit von Bauwerken. Sie spielt eine immer größere Rolle im Bauwesen. Die Kosten der Bauwerksinstandhaltung betragen je nach Art des Bauwerkes in Deutschland pro Jahr ca. 1-6% des Wiederbeschaffungswertes. Die Reduzierung des Instandhaltungsaufwandes durch Technik- und Management-Maßnahmen ist daher wirtschaftlich sinnvoll. Der Einsatz moderner Informations- und Kommunikationstechnologie auf dem Gebiet der Bestandsaufnahme und -analyse ist erforderlich, um einerseits die Bearbeitung von multimedialen Informationen über Ist- und Soll-Zustände von Bauwerken effektiver durchzuführen und um andererseits die Analyse von Schäden im Sinne einer Entscheidungshilfe zu unterstützen. Durch den Einsatz der WWW-Technologie kann die Bearbeitung auch verteilt im Datennetz über ferne Rechner hinweg erfolgen. Im Beitrag werden die Konzeptionierung und Implementierung des WWW-fähigen DV-Systems BINAS zur Unterstützung der Bestandsaufnahme und -analyse sowie die dafür erforderlichen Methoden und Werkzeuge vorgestellt. KW - Bauwerk KW - Bauschaden KW - Instandhaltung KW - Entscheidungsunterstützungssystem Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4994 ER - TY - JOUR A1 - Kabath, Meik A1 - Stuyts, Patrick T1 - Building Design towards 5-dimensions N2 - There exists a big gap between the capabilities of current 3D-CAD applications and their actual usage in practice. Many architects and planners still prefer to draft in 2D because the benefits of 3D modeling are difficult to explain. This presentation offers a basis to view the 3D building model not merely as the source for 2D plan generation. By adding extra dimensions like Time and Cost to the 3D building model it becomes possible to generate dynamic information on building construction progress with regards to used material, resources and cost. These additional benefits are key elements to many planners and contractors and may therefore widen the acceptance of 3D building modeling in general. KW - Bauindustrie KW - Baukonstruktion KW - Bauwerksplanung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2712 ER - TY - JOUR A1 - Zavadskas, Edmundas Kazimieras A1 - Kaklauskas, Arturas T1 - Civil Engineering Decision Support Systems in Lithuania N2 - Civil engineering decision support systems (construction, building life cycle, refurbishment, total quality management, innovation, etc.) created in Lithuania are described in this paper. The above decision support systems comprise of the following constituent parts: data (database and its management system), models (model base and its management system) and a user interface. Presentation of information in databases may be in conceptual (digital, textual, graphical, photographic, video) and quantitative forms. Quantitative information presented involves criteria systems and subsystems, units of measurement, values and initial weight fully defining the variants provided. The databases were developed providing a multiple criteria analysis of alternatives from economical, infrastructure, technical, technological, qualitative, legislative, social and other perspectives. This information is provided in a user-oriented way. Since the analysis of alternatives is usually performed by taking into account economical, infrastructure, technical, technological, qualitative and other factors, a model-base include models which enable a decision maker to carry out a comprehensive analysis of the variants available and make a proper choice. These systems, related questions and practical case study were analysed the paper. KW - Wissensmanagement KW - Bautechnik KW - Entscheidungsunterstützungssystem Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2579 ER - TY - JOUR A1 - Skrinar, Matjaz T1 - Computation of Stresses and Settlements under an arbitrary Point in Homogenous, elastic, isotropic Half-Space, under the Load described by a uniform Load over a general quadrilateral N2 - The problem of the computation of stresses and settlements in the half-space under various types of loads is often presented in geotechnical engineering. In 1885 Boussinesq advanced theoretical expressions to determine stresses at a point within an ideal mass. His equation considers a point load on the surface of a semi-infinite, homogeneous, isotropic, weightless, elastic half-space. Newmark in 1942 performed the integration of Boussinesq's equations for the vertical stress under a corner of a rectangular area loaded with a uniform load. The problem of the determination of vertical stresses under a rectangular shaped footing has been satisfactorily solved with renewal integration of the Boussinesq's equation over the arbitrary rectangle on surface of the half-space, with a non-uniform load represented with piecewise linear interpolation functions. The problem of the determination of stresses in the case when the footing shape is an arbitrary quadrilateral however remains unsolved. The paper discusses an approach to the computation of vertical stresses and settlements in an arbitrary point of the half-space, loaded with a uniform load, which shape in the ground plan can be a general four noded form with straight edges. Since the form is transformed into a biunit square and all integrations are performed over this area, all solutions are valid also for an arbitrary triangle by the implementation of the degeneration rule. KW - Halbraum KW - Isotropie KW - Spannung KW - Setzung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5338 ER - TY - JOUR A1 - Melnikov, B. E. A1 - Kadashevich, I. Y. A1 - Semenov, Artem T1 - Damage of Metalworkses under the Complex Varying Loading N2 - The phenomenological and computational aspects of the various damage models applications for the low and multi cyclic fatigue processes are investigated. Damage is considered as internal state variable, describing macroscopic effects of the progressive material degradation, within the framework of continuum damage mechanics. Present analysis is restricted to the case of isotropic damage, which can be modeled by a scalar variable. The strain, force and power types of kinetic equations for the damage evolution description are considered. The original mixed strain-power type damage model is developed for taking into account the different physical fracture mechanism in monotone and cyclic loading. The constitutive equations of plastic flow theory coupled and uncoupled to damage has been considered. The rational algorithm of implementation into finite element code is considered for developed damage models. Set of the computational experiments has been carried out for the various structures (huge aerials, pipelines, fastening units, vessel of nuclear reactor) and cases of loading. The comparison of the predictions of the developed model with experimental data is performed for 1X18H10T steel tubular specimens for complex paths of loading and for complex profiles beams under cyclic loading. Damage field distribution is the basic information for the prediction of crack initiation in structures. The developed method of structural parameter for stress concentration zones is discussed for correcting of crack location. It allows to describe the crack initiation near surface domain as observe in numerous experiments. KW - Stahlkonstruktion KW - Bruchmechanik KW - Dynamische Belastung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5409 ER - TY - JOUR A1 - Schulz, Thomas A1 - Kirschke, Heiko A1 - Schatter, G. T1 - Das Internet als Basis für die Produktinformation im Bauwesen N2 - Die Gesamtheit der Produktinformationen im Bauwesen stellt sich als sehr inkonsistente und redundante Informationsmenge dar. Die Hersteller stehen vor der Aufgabe, diese Produktinformationen nicht nur in der üblichen Katalogform sondern auch in neuen Medien wie CD-ROM und WWW zu publizieren. Einmal betriebener Erfassungsaufwand muß sich dabei durch eine einfache Mehrfachverwendung der Daten rentieren. Wegen seiner technologischen Eigenschaften eignet sich das WWW sehr gut als primäre Quelle für Produktinformationen. Vor allem wegen der möglichen Aktualität sollte es Grundlage für Publikationen in den anderen Medien sein. Mit verhältnismäßig geringem Aufwand lassen sich die WWW-Präsentation von Produktdaten so strukturieren, daß eine automatisierte Erfassung und Verarbeitung dieser Daten vereinfacht wird. So kann die Datenkonsistenz von der visuellen Präsentation in herkömmlichen Katalogen bis zur automatisch erstellten Produktdatenbank durchgängig gesichert werden. Vor dem Hintergrund der von Schnittstellenproblemen, heterogener Softwarestruktur und unzureichender Ausnutzung der Möglichkeiten der Informatik gekennzeichneten Situation im Bauwesen wird in generalisierter Ansatz mittels SGML vorgestellt. Mit einem derartigen Datenangebot werden neue, verteilte und vernetzte Anwendungen auf Grundlage derselben Produktdaten ermöglicht. KW - Bauwesen KW - Produktinformation KW - Internet Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5468 ER - TY - JOUR A1 - Zavadskas, Edmundas Kazimieras A1 - Kaklauskas, Arturas A1 - Viteikiene, Milda T1 - Database of Best Practices and Decision Support Web-based System for Construction Innovation N2 - Many construction and facilities management Web sites can be found on the Internet. The interested parties on construction and facilities management Web sites can find databases of best practices, calculators, analyzers, software, expert and decision support systems, neural networks, etc. Technological innovation mainly through changes in the availability of information and communication technology inclusive databases of best practices, calculators, analyzers, software, neural networks, decision support and expert systems that have been provided by a variety of new services developed by the construction and facilities management sectors. Most of all calculators, analyzers, software, decision support and expert systems, neural networks and on-line systems seek to find out how to make the most economic decisions and most of all these decisions are intended only for economic objectives. Alternatives under evaluation have to be evaluated not only from the economic position, but take into consideration qualitative, technical, technological and other characteristics as well. Based on the analysis of the existing calculators, analyzers, information, expert and decision support systems, neural networks and in order to determine most efficient versions of best practices a Decision Support Web-Based System for Construction Innovation (IDSS) was developed by Vilnius Gediminas Technical University. KW - Mehragentensystem KW - Lernendes System KW - Wissensverarbeitung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2173 ER - TY - JOUR A1 - Kaklauskas, Gintaris A1 - Cervenka, Vladimir A1 - Cervenka, Jan T1 - Deflection Calculation of RC Beams: Finite Element Software versus Design Code Methods N2 - The paper investigates accuracy of deflection predictions made by the finite element package ATENA and design code methods ACI and EC2. Deflections have been calculated for a large number of experimental reinforced concrete beams reported by three investigators. Statistical parameters have been established for each of the technique at different load levels, separately for the beams with small and moderate reinforcement ratio. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Balken Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2498 ER - TY - JOUR A1 - Êirinhevsky, V. V. A1 - Dîkhnyak, B. M. A1 - Êirichevsky, R. V. A1 - Êîzub, Y. G. T1 - Determination of the Temperature of Dissipative Warming and Parameters of Fracture in Elastomers with using of Singular Finite Elements N2 - For modeling of singular fields of stresses and deformations in elasters with a crack is offered to use of three-dimesional a special finite element. Weak compessible of elasters is taken into account on the basis of threefold approximation of fields of displacements, deformations and function of volume change. At intensive cyclic loading of the elastomer constructions with a crack it is necessary to take into account warming and large deformations at the crack top. The stress-deformed state elasters with a crack is determined from the decision of a nonlinear problem by a modified method Newton-Kantorovich. Account stress intensity factors for a rectangular plate with a various arrangement of a through crack is executed. Process of development of a surface crack and dissipative warming in prismatic a element of shift is investigated. KW - Elastomer KW - Temperatur KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5471 ER - TY - JOUR A1 - Pick, Tobias A1 - Heimsund, Bjoern-Ove A1 - Milbradt, Peter T1 - Development and Analysis of Sparse Matrix Concepts for Finite Element Approximation on general Cells N2 - In engineering and computing, the finite element approximation is one of the most well-known computational solution techniques. It is a great tool to find solutions for mechanic, fluid mechanic and ecological problems. Whoever works with the finite element method will need to solve a large system of linear equations. There are different ways to find a solution. One way is to use a matrix decomposition technique such as LU or QR. The other possibility is to use an iterative solution algorithm like Conjugate Gradients, Gauß-Seidel, Multigrid Methods, etc. This paper will focus on iterative solvers and the needed storage techniques... KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Bandmatrix Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2500 ER - TY - JOUR A1 - Motawa, Ibrahim A1 - Anumba, Chimay A1 - El-Hamalawi, A. T1 - Development of a Fuzzy System for Change Prediction in Construction Projects N2 - Change management has been the focus of different IT systems. These IT systems were developed to represent design information, record design rationale, facilitate design coordination and changes. They are largely based on managing reactive changes, particularly design changes, in which changes are recorded and then propagated to the relevant project members. However, proactive changes are hardly dealt with in IT systems. Proactive changes require estimating the likelihood of occurrence of a change event as well as estimating the degree of change impacts on project parameters. Changes in construction projects often result from the uncertainty associated with the imprecise and vague knowledge of much project information at the early stages of projects. This is a major outcome of the case studies carried out as part of this research. Therefore, the proposed model considers that incomplete knowledge and certain project characteristics are always behind change causes. For proactive changes, predicting a change event is the main task for modelling. The prediction model should strive to integrate these main elements: 1) project characteristics that lead to change 2) causes of change, 3) the likelihood of change occurrence, and 4) the change consequences. It should also define the dependency relationships between these elements. However, limited data (documented) are only available from previous projects for change cases and many of the above elements can only be expressed in linguistic terms. This means that the model will simulate the uncertainty and subjectivity associated with these sets of elements. Therefore, a fuzzy model is proposed in this research to capture these elements. The model analyses the impact of each set of elements on the other by assigning fuzzy values for these elements that express the uncertainty and subjectivity of their impact. The main aim is to predict change events and evaluate change effects on project parameters. The fuzzy model described above was developed in an IT system for operational purposes and was designed as a Java package of components with their supporting classes, beans, and files. This paper describes the development and the architecture of the proposed IT system to achieve these requirements. The system is intended to help project teams in dealing with change causes and then the change consequences in construction projects. KW - Mehragentensystem KW - Lernendes System KW - Fuzzy-Logik Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2180 ER - TY - JOUR A1 - Monobe, Kantaro A1 - Tanaka, Shigenori A1 - Furuta, Hitoshi T1 - Development of a System for Making Guide Maps based on the Idea of the Cognitive Map N2 - Digital maps are very easily applied as route guide maps. Route guide maps are provided through Web or a mobile phone services, and demand for such services is increasing. However, the production of a route guide map requires a great deal of time. Therefore, it is difficult for general users to make route guide maps. The purpose of the present research is the development of a system that can generate a route guide map using the Digital Map 2500 (Spatial Data Framework) published by the Geographical Survey Institute. This system will not require advanced equipment or expert knowledge. Therefore, anyone can produce route guide maps easily and quickly. By using the Digital Map 2500, the time and cost required in order to generate a map are reduced. Moreover, a useful route guide map can be created by simplifying the map form based on the human cognitive map. KW - Geoinformationssystem KW - Straßenkarte Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2688 ER - TY - JOUR A1 - Koike, Hirotaka A1 - Morimoto, Akinori A1 - Nomura, Kazuhiro T1 - Development of Urban Land Use Model to Compare Transit-Oriented and Automobile-Oriented Cities N2 - This study is an attempt to develop a simple simulation model that can compare the differences between automobile-oriented and transit-oriented cities, and clarify the difference between city forms by transportation modes. Following a theoretical model development, a series of simulation runs are tried. The model allocates people who commute to CBD from residential zones along a transportation corridor. As a result of many simulation analyses, it is shown that automobiles need much more traffic space in comparison with the transit as is shown by the proposed traffic space ratio both in CBD and along the corridor. KW - Verkehrsplanung KW - Simulation KW - Stadtplanung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2621 ER - TY - JOUR A1 - Schleicher, W. A1 - Rieche, M. T1 - Die Anwendung der computergestützten Tragwerksplanung von konstruktiven Ingenieurbauwerken im Zuge des Verkehrsprojektes Inter-City-Express 97 N2 - Die Entwicklung Berlins zur neuen Hauptstadt des vereinigten Deutschlands erfordert den umfangreichen Ausbau der innerstädtischen Verkehrswege und eine umfassende Einbindung in das bundesweite Verkehrsnetz. Der Ausbau der Inter-City-Express-Strecke zwischen Hannover und Berlin bedingte eine Umplanung großer Streckenabschnitte der Deutschen Bahn AG. Im Zeitalter der computergestützten Informationsverarbeitung sind gerade auf dem Gebiet der Tragwerksplanung konstruktiver Ingenieurbauten vielfältige Möglichkeiten gegeben. So ist bei der Planung von Brückenneubauten eine durchgehende computergestützte Konstruktion und Tragwerksplanung vom Vorentwurf bis hin zur Fertigung möglich. Weiterhin gestatten besondere Berechnungsmethoden bei speziellen Belastungsarten eine exaktere Schnittkraft- und Spannungsermittlung und dadurch eine dem wirklichen Tragverhalten entsprechende genauere Nachweisführung. An Beispielen aus dem konstruktiven Ingenieurbau im Zuge der Sanierung der Berliner Stadtbahn wird die Anwendung moderner Rechentechnik und computergestützter Konstruktionsmethoden und Berechnungsverfahren diskutiert. Die Berliner Stadtbahn wird in weiten Abschnitten über gemauerte Ziegelsteinviadukte geführt. Das Konzept der Sanierungsmaßnahmen sah neben der Anordnung einer lastverteilenden Platte einen Gleisaufbau als Feste Fahrbahn vor. Zusätzlich wurden die Gleisabstände den heutigen Bundesbahnvorschriften angepaßt. Aus diesem Grund wurde eine genaue Nachrechnung der Stadbahnviadukte unter Berücksichtigung der verschiedensten Parameter (z.B. Fugen in der lastverteilenden Platte, Rißbildung im Mauerwerk, Schubverformungen in Fugen zwischen Beton und Mauerwerk bei Überschreitung von Grenzwerten) erforderlich. Die zwischen dem Berliner Hauptbahnhof und dem Bahnhof Jannowitzbrücke befindliche Eisenbahnüberführung über die Holzmarktstraße wurden abgebrochen. Das neue Bauwerk besteht aus einer zweifeldrigen, schiefwinkligen Deckbrücke für 4 Gleise. Auf Grund der komplizierten geometrischen Randbedingungen erfolgte eine durchgängige computergestützte Erstellung der Ausführungsunterlagen. Die Hauptabmessungen der Konstruktion wurden mit Hilfe von Vermessungsdaten bestimmt, die im CAD-Programm verarbeitet wurden. Die CAD-Daten bildeten die geometrischen Eingangsgrößen für das Berechnungsprogramm. Die Querschnittsdimensionierung der Berechnung ging dann in die CAD-Bearbeitung ein. Die Koordinaten für die Werkstattfertigung sowie für die Montage auf der Baustelle ergaben sich ebenfalls aus den Berechnungsergebnissen. KW - Ingenieurbau KW - CAD Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4989 ER - TY - JOUR A1 - Kirchheim, Alfred A1 - Rudnicki, Andrzej T1 - Die Darstellung des Fahrgästeflusses im Nahverkehr als ein stochastischer Prozess N2 - Das Eintreffen der Passagiere einer Haltestelle eines öffentlichen Nahverkehrsmittel wird als stochastischer Prozeß beschrieben . Die Ankünfte der Nahverkehrsmittel stellen einen Erneuerungsprozeß dar , wohingegen die Ankünfte der Personen innerhalb einer Erneuerungsperiode als instationärer Poissonprozeß aufgefaßt wird. Über die Intensitätsfunktion liegen Messungen vor. Betrachtet wird die Gesamt- wartezeit der Personen an einer Haltestelle . KW - Öffentlicher Personennahverkehr KW - Wartezeit KW - Stochastisches Modell Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4653 ER - TY - JOUR A1 - Kaiser, Wolfgang T1 - Die unbegrenzten Einsatzmöglichkeiten von 3D-Modellierern N2 - Der Funktionsumfang von 3D-Modellierern und die Leistung allgemein zur Verfügung stehender Rechnersysteme gestatten die Modellierung beliebiger Objekte in jeder nur denkbaren Fachdisziplin. Das potentielle Leistungsvermögen von 3D-Modellierern sollte Anreiz sein, sie so alltäglich einzusetzen, wie die etablierten Standardapplikationen. Die im Vortrag gezeigten Modelle umfassen ein kleines Spektrum der möglichen Anwendungsgebiete. Weder vom (Daten)Umfang noch von ihrem Kompliziertheitsgrad stellen sie etwas Besonderes dar. Sie sollen nur das Interesse für einen alltäglichen Einsatz von 3D-Modellierern wecken und eventuell vorhandenen Einsatzschwellen abbauen helfen. Die im Vortrag gezeigten Bildfolgen sind unter http://www.uni-weimar.de/animationen zu finden. KW - Dreidimensionales Modell KW - Anwendung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5257 ER - TY - JOUR A1 - Wiedemann, A. T1 - Digital Architectural Photogrammetry for Building Registration N2 - For many purposes geometric information about existing buildings is necessary, e.g. planing of conservation or reconstruction. Architectural photogrammetry is a technique to acquire 3D geometric data of buildings for a CAD model from images. In this paper the state of the art in architectural photogrammetry and some developments towards automation are described. The photogrammetric process consists of image acquisition, orientation and restitution. Special attention is put on digital methods, from digital image acquisition to restitution methods, supported by digital image processing. There are a few field of development towards automation, e.g. feature extraction, extraction of edges and lines and the detection of corresponding points. The acquired data may be used in a CAD environment or for visualization in Virtual Reality Models, using digital orthoimages for texture mapping. KW - Bauwerk KW - Projektdokumentation KW - Photogrammetrie Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4892 ER - TY - JOUR A1 - Kicinger, Rafal A1 - Arciszewski, Tomasz A1 - De Jong, Kenneth T1 - Distributed Evolutionary Design: Island-Model-based Optimization of Steel Skeleton Structures in Tall Buildings N2 - This paper presents results of a study on distributed, or parallel, evolutionary computation in the topological design of steel structural systems in tall buildings. It describes results of extensive experimental research on various parallel evolutionary architectures applied to a complex structural design problem. The experiments were conducted using Inventor 2003, a networkbased evolutionary design support tool developed at George Mason University. First, a general introduction to evolutionary computation is provided with an emphasis on recent developments in parallel evolutionary architectures. Next, a discussion of conceptual design of steel structural systems in tall buildings is presented. Further, Inventor 2003 is briefly introduced as well as its design representation and evolutionary computation characteristics. Next, the results obtained from systematic design experiments conducted with Inventor 2003 are discussed. The objective of these experiments was to qualitatively and quantitatively investigate evolution of steel structural systems in tall buildings during a distributed evolutionary design process as well as to compare efficiency and effectiveness of various parallel evolutionary architectures with the traditional evolutionary design approaches. Two connectivity topologies (ring topology and fully-connected topology) have been investigated for four populations of structural designs evolving in parallel and using various migration strategies. Also, results of the initial sensitivity studies are reported in which two ways of initializing distributed evolutionary design processes were investigated, using either arbitrarily selected designs as initial parents or randomly generated ones. Finally, initial research conclusions are presented. KW - Mehragentensystem KW - Lernendes System KW - Stahlbau KW - Skelettbau KW - Optimierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2195 ER - TY - JOUR A1 - Semenov, Vitaly A1 - Bazhan, Andrew A1 - Morozov, Sergey T1 - Distributed STEP-Compliant Platform for Multimodal Collaboration in Architecture, Engineering, and Construction N2 - This paper presents an innovative software platform OpenSTEP intended to build advanced distributed integrated systems and to conduct multidisciplinary collaborative projects in both academy and industry. The paper discusses an open system architecture, methodology, component library and CASE toolkit enabling the developers to build a wide range of interoperable applications and systems compliant with STEP and, particularly, with IFC becoming the increasingly important standard for information integration in architecture, engineering and construction. KW - Framework KW - API KW - STEP KW - Verteiltes System Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2616 ER - TY - JOUR A1 - Lizounov, P. P. T1 - Dynamics of solid and deformable Bodies Systems at complex Movements N2 - Analytical models, describing oscillations of systems of interconnected solid and deformable bodies,making a complex movement in fields of inertia forces and gravitation forces, are resulted. Method of numerical investigation of dynamics of the specified systems, based on sharing of parameter prolongation method, Newton-Kantorovich algorithm, Flocke and Liapunov hteories, is developed. On the basis of constructed analytical models and numerical techniques a new, practically important problems of dynamics of systems, consisting of solid bodies, flexible rods, membranes and soft shells, which make a complex movement in fields of forces of inertia and gravity are solved. The received results are used during designing of responsible elements of structures, making a complex movement, which find application in construction and mechanical engineering. KW - Festkörpermechanik KW - Dynamische Belastung KW - Numerisches Verfahren Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5410 ER - TY - JOUR A1 - Kwak, Hyo-Gyoung A1 - Kim, Jin-Kook T1 - Efficient Shoring System in RC Frame Structures N2 - In this paper, systematic analyses for the shoring systems installed to support the applied loads during construction are performed on the basis of the numerical approach. On the basis of a rigorous time-dependent analysis, structural behaviors of reinforced concrete (RC) frame structures according to the changes in design variables such as the types of shoring systems, shore stiffness and shore spacing are analyzed and discussed. The time-dependent deformations of concrete such as creep and shrinkage and construction sequences of frame structures are also taken into account to minimize the structural instability and to reach to an improved design of shoring system because these effects may increase the axial forces delivered to the shores. In advance, the influence of the column shortening effect, generally mentioned in a tall building structure, is analyzed. From many parametric studies, it has been finally concluded that the most effective shoring system in RC frame structures is 2S1R (two shores and one reshore) regardless of the changes in design variables. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Skelettbau KW - Construction Sequence KW - Shoring System KW - Shore Stiffness KW - Shore Spacing Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2511 ER - TY - JOUR A1 - Caetano, A. M. T1 - Eigenvalue Distribution for the Stokes Operator N2 - The aim of this talk is to show that the methods used by Métivier and Lapidus to study the eigenvalue distribution of elliptic operators (e.g., of the Dirichlet Laplacian) can be adapted to the study of the similar problem for the Stokes operator. In this way we get asymptotic formulae for the eigenvalues of the latter operator even in the case when the underlying domain has an extremely irregular (fractal) boundary. In the case the boundary is not that irregular (e.g., when it is Lipschitz) the estimates we obtain are much better than the ones we can find in the current literature. KW - Stokes-Problem KW - Eigenwert Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5005 ER - TY - JOUR A1 - Sellerhoff, F. A1 - Milbradt, Peter A1 - Lippert, C. T1 - Ein dimensionsunabhängiges topologisches Modell auf der Basis von Simplexen N2 - Die geometrische Modellierung hat in den Ingenieurwissenschaften eine große Bedeutung erlangt. Die Visualisierung von zwei- oder dreidimensionalen Problemstellungen ist aus heutigen Anwendungen nicht mehr wegzudenken. Zunehmend rücken Aufgabenstellungen aus dem Bereich der geometrischen Modellierung in den Vordergrund, die über die etablierten Dimensionen 1-3 hinausgehen und die nicht mehr rein geometrischer Natur sind. Hierzu zählen Aufgabenstellungen aus den Bereichen numerische Simulation, Parameteridentifikation und Strukturanalyse. Auf diese nicht-geometrischen Aufgabenstellungen sollen geometrische Verfahren, wie z.B. Triangulation, konvexe Hülle, geometrischer Schnitt und Interpolation angewendet werden. Hierzu werden diese Algorithmen, die alle auf der klassischen Geometrie des euklidischen Raumes beruhen, auf ihre Übertragbarkeit hin analysiert und überarbeitet. Am Beispiel einer Parameteridentifikation wird eine systematische Vorgehensweise vorgestellt, die es ermöglicht, trotz weniger Versuchsrechnungen den Bereich der in Frage kommenden Parameter umfassend zu beschreiben. Dies ermöglicht ein besseres Verständnis der Zusammenhänge der Parameter untereinander. Häufig existieren mehr als eine Parameterkombination, so daß diese eine Isolinie formen, die ihrerseits unendlich viele Lösungen des gestellten Problemes im Untersuchungsgebiet beschreibt. KW - Parameteridentifikation KW - Strukturanalyse KW - Visualisierung KW - Mehrdimensionalität Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4616 ER - TY - JOUR A1 - Fischer, A. A1 - Steinhage, V. T1 - Ein modellbasiertes Konzept zur städteplanerischen Kartierung durch digitale Bildanalyse N2 - There is an increasing need for 3D building extraction from aerial images for various applications such astown planning, environmental- and property-related studies. Aerial images usually reveal on one hand a certain amount of information not relevant for the given task of building extraction like vegetation, cars etc. On the other hand there is a loss of relevant information due to occlusions, low contrasts or disadvantageous perspectives. Therefore a promising concept for automated building reconstruction must incorporate a suffciantly complete model of the objects of interest. We propose a model-based approach to 3D building extraction from aerial images which reveals a tight coupling between a generic 3D object model and an explicit 2D image model. The generic object model employes domain specific volumetric primitives (i. e. building part models) and combination schemes. To cover the gap between 3D object models and 2D image data the image model is employed to predict the projective building appearences in aerial images. We present a strategy for a model-based building extraction based on the recognition-by-components principle and show first experimental results derived from international test sets KW - Stadtplanung KW - Kartierung KW - Bildanalyse KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4870 ER - TY - JOUR A1 - Kämmerer, Lutz A1 - Hempel, Lorenz T1 - Eine Heuristik zur Lösung von Stapelproblemen N2 - Bei der Betrachtung von Stapelproblemen ergibt sich unter anderem folgendes Problem: Ein gegebener Stapel - bestehend aus den Elementen v i der Menge V - soll an anderer Stelle in einer vorgeschriebenen, veränderten Struktur wieder aufgebaut werden. Dazu stehen Hilfsstapelplätze zur Verfügung. Die Optimierung dieses Problems hinsichtlich der Anzahl der benötigten Hilfsstapelplätze ist NP-vollständig. Es werden Erfahrungen mit einem Branch-and-Bound Algorithmus zur Lösung des Problems vorgestellt sowie ein heuristischer Algorithmus diskutiert KW - Stapelproblem KW - Heuristik Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5207 ER - TY - JOUR A1 - Abdalla, Jamal T1 - Elements of an Agent-based Mediative Communication Protocol for Design Objects N2 - Integrated structural engineering system usually consists of large number of design objects that may be distributed across different platforms. These design objects need to communicate data and information among each other. For efficient communication among design objects a common communication protocol need to be defined. This paper presents the elements of a communication protocol that uses a mediator agent to facilitate communication among design objects. This protocol is termed the Mediative Communication Protocol (MCP). The protocol uses certain design communication performatives and the semantics of an Agent Communication language (ACL) mainly the Knowledge and Query Manipulation Language (KQML) to implement its steps. Details of a Mediator Agent, that will facilitate the communication among design objects, is presented. The Unified Modeling Language (UML) is used to present the Meditative protocol and show how the mediator agent can be use to execute the steps of the meditative communication protocol. An example from structural engineering application is presented to demonstrate and validate the protocol. It is concluded that the meditative protocol is a viable protocol to facilitate object-to-object communication and also has potential to facilitate communication among the different project participants at the higher level of integrated structural engineering systems. KW - Mehragentensystem KW - Lernendes System KW - Kommunikationsprotokoll Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2207 ER -