TY - CHAP A1 - Miro, Shorash A1 - Hartmann, Dietrich A1 - Schanz, Tom A1 - Zarev, Veselin ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - SYSTEM IDENTIFICATION METHODS FOR GROUND MODELS IN MECHANIZED TUNNELING T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - Due to the complex interactions between the ground, the driving machine, the lining tube and the built environment, the accurate assignment of in-situ system parameters for numerical simulation in mechanized tunneling is always subject to tremendous difficulties. However, the more accurate these parameters are, the more applicable the responses gained from computations will be. In particular, if the entire length of the tunnel lining is examined, then, the appropriate selection of various kinds of ground parameters is accountable for the success of a tunnel project and, more importantly, will prevent potential casualties. In this context, methods of system identification for the adaptation of numerical simulation of ground models are presented. Hereby, both deterministic and probabilistic approaches are considered for typical scenarios representing notable variations or changes in the ground model. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27771 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Scheiber, Frank ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - ROBUSTNESS IN CIVIL ENGINEERING - INFLUENCES OF THE STRUCTURAL MODEL ON THE EVALUATION OF THE STRUCTURAL ROBUSTNESS T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - The topic of structural robustness is covered extensively in current literature in structural engineering. A few evaluation methods already exist. Since these methods are based on different evaluation approaches, the comparison is difficult. But all the approaches have one in common, they need a structural model which represents the structure to be evaluated. As the structural model is the basis of the robustness evaluation, there is the question if the quality of the chosen structural model is influencing the estimation of the structural robustness index. This paper shows what robustness in structural engineering means and gives an overview of existing assessment methods. One is the reliability based robustness index, which uses the reliability indices of a intact and a damaged structure. The second one is the risk based robustness index, which estimates the structural robustness by the usage of direct and indirect risk. The paper describes how these approaches for the evaluation of structural robustness works and which parameters will be used. Since both approaches needs a structural model for the estimation of the structural behavior and the probability of failure, it is necessary to think about the quality of the chosen structural model. Nevertheless, the chosen model has to represent the structure, the input factors and reflect the damages which occur. On the example of two different model qualities, it will be shown, that the model choice is really influencing the quality of the robustness index. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27845 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Nechytailo, Oleksandr A1 - Horokhov, Yevgen A1 - Kushchenko, Vladimir ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - ANALYSIS OF THE MODE OF DEFORMATION OF THE SUB-PULLEY STRUCTURES ON SHAFT SLOPING HEADGEAR STRUCTURES T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - A numerical analysis of the mode of deformation of the main load-bearing components of a typical frame sloping shaft headgear was performed. The analysis was done by a design model consisting of plane and solid finite elements, which were modeled in the program «LIRA». Due to the numerical results, the regularities of local stress distribution under a guide pulley bearing were revealed and parameters of a plane stress under both emergency and normal working loads were determined. In the numerical simulation, the guidelines to improve the construction of the joints of guide pulleys resting on sub-pulley frame-type structures were established. Overall, the results obtained are the basis for improving the engineering procedures of designing steel structures of shaft sloping headgear. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27826 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Lahmer, Tom A1 - Ghorashi, Seyed Shahram ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - XFEM-BASED CRACK IDENTIFICATION APPLYING REGULARIZING METHODS IN A MULTILEVEL APPROACH T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - Many structures in different engineering applications suffer from cracking. In order to make reliable prognosis about the serviceability of those structures it is of utmost importance to identify cracks as precisely as possible by non-destructive testing. A novel approach (XIGA), which combines the Isogeometric Analysis (IGA) and the Extended Finite Element Method (XFEM) is used for the forward problem, namely the analysis of a cracked material, see [1]. Applying the NURBS (Non-Uniform Rational B-Spline) based approach from IGA together with the XFEM allows to describe effectively arbitrarily shaped cracks and avoids the necessity of remeshing during the crack identification problem. We want to exploit these advantages for the inverse problem of detecting existing cracks by non-destructive testing, see e.g. [2]. The quality of the reconstructed cracks however depends on two major issues, namely the quality of the measured data (measurement error) and the discretization of the crack model. The first one will be taken into account by applying regularizing methods with a posteriori stopping criteria. The second one is critical in the sense that too few degrees of freedom, i.e. the number of control points of the NURBS, do not allow for a precise description of the crack. An increased number of control points, however, increases the number of unknowns in the inverse analysis and intensifies the ill-posedness. The trade-off between accuracy and stability is aimed to be found by applying an inverse multilevel algorithm [3, 4] where the identification is started with short knot vectors which successively will be enlarged during the identification process. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27717 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Keitel, Holger ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - QUANTIFYING THE QUALITY OF PARTIAL MODEL COUPLING AND ITS EFFECT ON THE SIMULATED STRUCTURAL BEHAVIOR T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - The process of analysis and design in structural engineering requires the consideration of different partial models, for example loading, structural materials, structural elements, and analysis types. The various partial models are combined by coupling several of their components. Due to the large number of available partial models describing similar phenomena, many different model combinations are possible to simulate the same aspects of a structure. The challenging task of an engineer is to select a model combination that ensures a sufficient, reliable prognosis. In order to achieve this reliable prognosis of the overall structural behavior, a high individual quality of the partial models and an adequate coupling of the partial models is required. Several methodologies have been proposed to evaluate the quality of partial models for their intended application, but a detailed study of the coupling quality is still lacking. This paper proposes a new approach to assess the coupling quality of partial models in a quantitative manner. The approach is based on the consistency of the coupled data and applies for uni- and bidirectional coupled partial models. Furthermore, the influence of the coupling quality on the output quantities of the partial models is considered. The functionality of the algorithm and the effect of the coupling quality are demonstrated using an example of coupled partial models in structural engineering. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27689 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Kulchytskyy, Artem A1 - Horokhov, Yevgen A1 - Gubanov, Vadim A1 - Golikov, Alexandr ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - THE INFLUENCE OF THE LOCAL CONCAVITY ON THE FUNCTIONING OF BEARING SHELL OF HIGH-RISE CONSTRUCTION T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - Areas with various defects and damages, which reduce carrying capacity, were examined in a study of metal chimneys. In this work, the influence of the local dimples on the function of metal chimneys was considered. Modeling tasks were completed in the software packages LIRA and ANSYS. Parameters were identified, which characterize the local dimples, and a numerical study of the influence of local dimples on the stress-strain state of shells of metal chimneys was conducted. A distribution field of circular and meridional tension was analyzed in a researched area. Zones of influence of dimples on the bearing cover of metal chimneys were investigated. The bearing capacities of high-rise structures with various dimple geometries and various cover parameters were determined with respect to specified areas of the trunk. Dependent relationships are represented graphically for the decrease in bearing capacity of a cover with respect to dimples. Diameter and thickness of covers of metal chimneys were constructed according to the resulting data. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27701 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Wudtke, Idna ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - CONSTITUTIVE MODELING OF CRYSTALLINE MATERIALS WITH TEXTURE CHARACTERISTICS T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - The analysis of the response of complex structural systems requires the description of the material constitutive relations by means of an appropriate material model. The level of abstraction of such model may strongly affect the quality of the prognosis of the whole structure. In context to this fact, it is necessary to describe the material in a convenient sense as exact but as simple as possible. All material phenomena of crystalline materials e.g. steel, affecting the behavior of the structure, rely on physical effects which are interacting over spatial scales from subatomic to macroscopic range. Nevertheless, if the material is microscopically heterogenic, it might be appropriate to use phenomenological models for the purpose of civil engineering. Although constantly applied, these models are insufficient for steel materials with microscopic characteristics such as texture, typically occurring in hot rolled steel members or heat affected zones of welded joints. Hence, texture is manifested in crystalline materials as a regular crystallographic structure and crystallite orientation, influencing macroscopic material properties. The analysis of structural response of material with texture (e.g. rolled steel or heat affected zone of a welded joint) obliges the extension of the phenomenological material description of macroscopic scale by means of microscopic information. This paper introduces an enrichment approach for material models based on a hierarchical multiscale methodology. This has been done by describing the grain texture on a mesoscopic scale and coupling it with macroscopic constitutive relations by means of homogenization. Due to a variety of available homogenization methods, the question of an assessment of coupling quality arises. The applicability of the method and the effect of the coupling method on the reliability of the response are presented on an example. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27910 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Schmeikal, Bernd Anton ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - BAUHAUS ISOMETRY AND FIELDS T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - While integration increases by networking, segregation strides ahead too. Most of us fixate our mind on special topics. Yet we are relying on our intuition too. We are sometimes waiting for the inflow of new ideas or valuable information that we hold in high esteem, although we are not entirely conscious of its origin. We may even say the most precious intuitions are rooting in deep subconscious, collective layers of the mind. Take as a simple example the emergence of orientation in paleolithic events and its relation to the dihedral symmetry of the compass. Consider also the extension of this algebraic matter into the operational structures of the mind on the one hand and into the algebra of geometry, Clifford algebra as we use to call it today, on the other. Culture and mind, and even the individual act of creation may be connected with transient events that are subconscious and inaccessible to cognition in principle. Other events causative for our work may be merely invisible too us, though in principle they should turn out attainable. In this case we are just ignorant of the whole creative process. Sometimes we begin to use unusual tools or turn into handicraft enthusiasts. Then our small institutes turn into workshops and factories. All this is indeed joining with the Bauhaus and its spirit. We shall go together into this, and we shall present a record of this session. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27859 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Castillo-Pérez, Raúl A1 - Cedillo - Díaz, A. del C. A1 - Kravchenko, Vladislav A1 - Oviedo - Galdeano, H. ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - COMPUTATION OF THE REFLECTANCE AND TRANSMITTANCE FOR AN INHOMOGENEOUS LAYERED MEDIUM WITH TURNING POINT S USING THE WKB AND SPPS METHODS T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - Electromagnetic wave propagation is currently present in the vast majority of situations which occur in veryday life, whether in mobile communications, DTV, satellite tracking, broadcasting, etc. Because of this the study of increasingly complex means of propagation of lectromagnetic waves has become necessary in order to optimize resources and increase the capabilities of the devices as required by the growing demand for such services. Within the electromagnetic wave propagation different parameters are considered that characterize it under various circumstances and of particular importance are the reflectance and transmittance. There are several methods or the analysis of the reflectance and transmittance such as the method of approximation by boundary condition, the plane wave expansion method (PWE), etc., but this work focuses on the WKB and SPPS methods. The implementation of the WKB method is relatively simple but is found to be relatively efficient only when working at high frequencies. The SPPS method (Spectral Parameter Powers Series) based on the theory of pseudoanalytic functions, is used to solve this problem through a new representation for solutions of Sturm Liouville equations and has recently proven to be a powerful tool to solve different boundary value and eigenvalue problems. Moreover, it has a very suitable structure for numerical implementation, which in this case took place in the Matlab software for the valuation of both conventional and turning points profiles. The comparison between the two methods allows us to obtain valuable information about their perfor mance which is useful for determining the validity and propriety of their application for solving problems where these parameters are calculated in real life applications. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170306-27598 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - THES A1 - Karaki, Ghada T1 - Assessment of coupled models of bridges considering time-dependent vehicular loading N2 - Bridge vibration due to traffic loading has been a subject of extensive research in the last decades. The focus of such research has been to develop solution algorithms and investigate responses or behaviors of interest. However, proving the quality and reliability of the model output in structural engineering has become a topic of increasing importance. Therefore, this study is an attempt to extend concepts of uncertainty and sensitivity analyses to assess the dynamic response of a coupled model in bridge engineering considering time-dependent vehicular loading. A setting for the sensitivity analysis is proposed, which enables performing the sensitivity analysis considering random stochastic processes. The classical and proposed sensitivity settings are used to identify the relevant input parameters and models that have the most influence on the variance of the dynamic response. The sensitivity analysis exercises the model itself and extracts results without the need for measurements or reference solutions; however, it does not offer a means of ranking the coupled models studied. Therefore, concepts of total uncertainty are employed to rank the coupled models studied according to their fitness in describing the dynamic problem. The proposed procedures are applied in two examples to assess the output of coupled subsystems and coupled partial models in bridge engineering considering the passage of a heavy vehicle at various speeds. N2 - Brückenschwingungen infolge von Verkehrslasten sind seit mehreren Jahrzehnten Gegenstand intensiver Forschung. Im Fokus stand hierbei im Besonderen die Entwicklung von Lösungsalgorithmen zur Ermittlung des dynamischen Bauwerkverhaltens. Begleitet ist diese Entwicklung von der Frage nach der Qualität und Zuverlässigkeit dieser Modelle für den Gebrauch im konstruktiven Ingenieurbau. In diesem Zusammenhang werden in der vorliegenden Arbeit Konzepte der Unsicherheits- und Sensitivitätsanalyse erweitert, um das dynamische Bauwerkverhalten unter Berücksichtigung transienter Fahrzeuglasten bei gekoppelten Modellen des Brückenbaus zu bewerten. Bestehende Sensitivitätsanalysen werden ergänzt, um diese auch unter Berücksichtigung von stochastischen Prozessen durchführen zu können. Die klassische und die erweiterte Methode werden angewandt, um relevante Eingangsparameter sowie Partialmodelle mit wesentlichem Einfluss auf die Varianz der dynamischen Strukturantwort zu identifizieren. Die mit Hilfe der Sensitivitätsanalyse ermittelbaren Kennzahlen können ohne Bezug zu einer Referenzlösung in die Modellbewertung einfließen, allerdings ist es nicht möglich, die Modelle hinsichtlich der realitätsnahen Abbildung des dynamischen Problems zu bewerten. Um dies zu ermöglichen, wurden Konzepte der Gesamtunsicherheit verwendet. Die vorgestellten Methoden wurden auf zwei Beispiele angewandt, um die Ergebnisse von gekoppelten Subsystemen und gekoppelten Partialmodellen des Brückenbaus zu evaluieren. Hierbei handelt es sich um die Überfahrt von schweren Fahrzeugen mit verschiedenen Geschwindigkeiten. T3 - Schriftenreihe des DFG Graduiertenkollegs 1462 Modellqualitäten // Graduiertenkolleg Modellqualitäten - 5 KW - Ingenieurbau KW - bridge-vehicle interaction KW - random vibrations KW - sensitivity and uncertainty analysis Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120402-15894 ER - TY - CHAP A1 - Mirallas Hernandez, Catherine T1 - E-Books : Interessenkonflikte zwischen Bibliotheken, Nutzern und Verlagen T2 - Alles digital? : E-Books in Studium und Lehre N2 - Beitrag während der Weimarer EDOC-Tage 2011 KW - Bibliothek KW - Verlag KW - Benutzer KW - Elektronische Buch KW - Buchmarkt Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120404-15941 SP - 54 EP - 63 PB - Verlag der Bauhaus-Universität CY - Weimar ER - TY - CHAP A1 - Mumenthaler, Rudolf T1 - E-Books und E-Reader als Herausforderung für Bibliotheken T2 - Alles digital? : E-Books in Studium und Lehre N2 - Beitrag während der Weimarer EDOC-Tage 2011 KW - Elektronisches Buch KW - E-Book-Reader KW - Elektronische Formate KW - Bibliothek Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120403-15913 SP - 44 EP - 51 PB - Verlag der Bauhaus-Universität CY - Weimar ER - TY - THES A1 - Posern, Konrad T1 - Untersuchungen von Magnesiumsulfat-Hydraten und Sulfat/Chlorid-Mischungen für die Eignung als Aktivstoff in Kompositmaterialien für die thermochemische Wärmespeicherung N2 - Die thermochemische Wärmespeicherung über reversible Salzhydratation stellt einen aussichtsreichen Weg zur Speicherung von Niedertemperaturwärme, wie z.B. solarer Energie, dar. Untersuchungen an Magnesiumsulfat-Hydraten zeigen, dass das bei 130°C entwässerte Magnesiumsulfat-Heptahydrat seinen thermodynamisch stabilen Endzustand während der Reaktion mit gasförmigem Wasser nicht wieder erreicht. Um diese kinetische Hemmung zu überwinden und den Einfluss von unterschiedlichen Porenräumen auf die Hydratation bzw. Sorption des Magnesiumsulfates zu charakterisieren, wurde das Magnesiumsulfat in Trägermaterialien auf Basis offenporiger Gläser mit durchschnittlichen Porendurchmessern von 4 nm bis 1,4 µm eingebracht und diese Kompositmaterialien untersucht. Dabei ist festgestellt worden, dass jede salzbezogene Sorptionswärme im Porenraum höher ist, als die des ungeträgerten Salzes und mit kleiner werdendem Porenradius weiter zunimmt. Weiterhin wurden Teile des Magnesiumsulfates mit niedrig deliqueszierenden Salzen substituiert, um die Wasseraufnahme und somit die Wärmespeicherkapazität zu erhöhen. Dies stellt einen neuen Weg zur Herstellung von Kompositmaterialien dar, über den man Eigenschaften wie Deliqueszenzfeuchte und Desorptionstemperatur einstellen und an die Sorptionsbedingungen eines Speichers anpassen kann. Als niedrig deliqueszierende Salze wurden Magnesiumchlorid und Lithiumchlorid als Zusätze untersucht, wobei ein Ansteigen der Sorptionswärme und Wasseraufnahme mit steigendem Chloridanteil festgestellt wurde. Aufgrund der geringeren Deliqueszenzfeuchte des Lithiumchlorides gegenüber dem Magnesiumchlorid wurden bei gleichen Massenverhältnissen höhere Sorptionswärmen erzielt. Untersuchungen zu Zinksulfat in Verbindung mit Chloriden bescheinigen diesem Salz -speziell bei tieferen Entwässerungstemperaturen- eine gute Eignung als Aktivstoff zur Wärmespeicherung. Zusammenfassend konnte festgestellt werden, dass sich die Wärmespeicherkapazitäten über die Porengröße, in die das Salz eingebracht wird, und die gewählte Mischungszusammensetzung steuern lassen. Die gemessenen Sorptionswärmen ermöglichen insbesondere bei niedrigen Sorptionstemperaturen und hohen Luftfeuchtigkeiten den Schluss, dass die Verwendung von Salzmischungen als Aktivkomponente in Kompositmaterialien einen geeigneten Weg zur thermochemischen Speicherung solarer Wärme (≤130 °C) darstellt. N2 - Thermochemical heat storage based on reversible salt hydration is a promising way for low temperature storage, like solar energy. Investigations on magnesium sulfate hydrates, which were dehydrated at 130 °C show, that the thermodynamic stable product of the reaction with gaseous water is not reached. To overcome this kinetic hindrance different host materials were impregnated with magnesium sulfate and the composite materials were characterized. The sorption behavior of the dehydrated sulfate within host materials with different pore sizes (4 nm – 1.4 µm) was investigated. It could be found, that the heat of sorption of magnesium sulfate increases with decreasing pore sizes and correlates with the water sorption. Additionally different parts of magnesium sulfate were substituted with low deliquescent salts to improve the water uptake and the heat storage capacity. The using of such salt mixtures is a new way to set parameters like deliquescence relative humidity and temperature of desorption on the performance of a heat storage system. Magnesium chloride and lithium chloride were used as low deliquescent salts. The heat of sorption and the water uptake increase with an increasing amount of the chloride. Due to the lower deliquescence relative humidity of lithium chloride compared to the magnesium chloride, higher heats of sorption could be measured at the same mass ratios. Mixtures of zinc sulfate with chlorides are suitable for thermochemical heat storage applications, in particular at low temperatures of desorption. In summary, it was found that the heat storage capacities are influenced by the pore size of the host material and the chosen salt mixture. At low sorption temperatures and high relative humidities the using of salt mixtures is an appropriate way for the thermochemical storage of solar heat (≤130 °C). KW - Thermische Energiespeicherung KW - Anorganische Salze KW - Thermochemische Wärmespeicherung KW - Sorptionswärme KW - poröse Trägermaterialien KW - Salzmischungen KW - Magnesiumsulfat Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120704-16784 ER - TY - THES A1 - Nerlich, Luise T1 - KLANG tektonik _ Entwurfsgrammatik in Architektur und Musik im Werk des Architekten und Komponisten Iannis Xenakis N2 - klang_tektonik Design by grammar in architecture and music Architectural design is a creative process. Its emergence requires a creative component and it cannot be systematized. But while teaching architecture, work with a method to design is an essential aspect. In addition to the intuitive methods of design, however, also exist grammars, which explicit rules postulated for form finding and can be taught as such. In consideration of formative architectural and musical design, parameters will be presented, to design a transformation of music into architecture. Two revolutionary works are created in the 1950s, the composition Metastaseis and the Philips Pavilion for the World Exhibition in Brussels by the architect and composer Iannis Xenakis. Based on these works, there will be presented the method, how to replace musical parameters in to architectural parameters. This process provides the basis for an accurate spatial transformation model, which is designed on the basis of mathematical functions and has a strong similarity in language between the shape of the composition Metastaseis and architecture of the pavilion. N2 - Architektonisches Entwerfen ist ein kreativer Prozess, der eine Lösung hervorbringt, die in ihrer Form und ihrer Funktionalität so noch nicht bestand. Resultat eines architektonischen Entwurfes ist ein Original, dessen Entstehen eine schöpferische Komponente erfordert. Dieser kreative Prozess ist nicht systematisierbar und kann auch nicht als Methode wiederholbar gemacht werden. Im Rahmen der architektonischen Lehre ist die Vermittlung von Methoden zur Entwurfsfindung jedoch ein wesentlicher Aspekt. Der hier vorgestellte Entwurf möchte zeigen, dass der Auffassung, allein intuitive Methoden als Entwurfsgrundlage zu nutzen, die Auffassung entgegen steht, eine reglementierte Methode zur Entwurfs- und Formfindung anzuwenden. Eine solche reglementierte Methode wird hierbei als Entwurfsgrammatik bezeichnet. In den 1950er Jahren entstehen zwei revolutionäre Werke des Komponisten und Architekten Iannis Xenakis: die Komposition Metastaseis und der Philips-Pavillon für die Weltausstellung in Brüssel. Basierend auf diesen Arbeiten wird eine Methode vorgestellt, welche musikalische Parameter in architektonischen Parameter transformiert. Diese Methode bildet die Grundlage für ein exaktes räumliches Transformation-Modell, welches aus mathematischen Funktionen abgeleitet ist. Dabei weißt das Transformations-Modell eine starke Ähnlichkeit mit der Architektur des Pavillons auf. KW - Architektur KW - Musik KW - architektonischer Entwurf KW - Systementwurf KW - architektonischer Entwurf KW - Musik und Architektur KW - Philips Pavillon KW - Iannis Xenakis KW - Metastaseis Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120607-16689 ER - TY - CHAP A1 - Lucius, Wulf D. von T1 - Perspektiven für Verlage im digitalen Zeitalter T2 - Alles digital? : E-Books in Studium und Lehre N2 - Beitrag während der Weimarer EDOC-Tage 2011 KW - Verlag KW - Digital Rights Management KW - Urheberrecht KW - Vertriebsweg KW - Freemium KW - Preispolitik Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120327-15813 SP - 32 EP - 41 PB - Verlag der Bauhaus-Universität CY - Weimar ER - TY - BOOK ED - Maier, Matthias ED - Simon-Ritz, Frank T1 - Alles digital? E-Books in Studium und Forschung : Weimarer EDOC-Tage 2011 N2 - Es ist ein Bild aus alten Tagen: ein wissbegieriger Student, auf der Suche nach fundierter wissenschaftlicher Information, begibt sich an den heiligsten Ort aller Bücher – die Universitätsbibliothek. Doch seit einiger Zeit tummeln sich Studierende nicht mehr nur in Bibliotheken, sondern auch immer häufiger im Internet. Sie suchen und finden dort digitale Bücher, sogenannte E-Books. Wie lässt sich der Wandel durch den Einzug des E-Books in das etablierte Forschungssystem beschreiben, welche Konsequenzen lassen sich daraus ablesen und wird schließlich alles digital, sogar die Bibliothek? Diesen Fragen geht ein elfköpfiges Expertenteam aus Deutschland und der Schweiz während der zweitägigen Konferenz auf den Grund. Bei den Weimarer E-DOC-Tagen geht es nun um die Veränderung des institutionellen Gefüges rund um das digitale Buch. Denn traditionell sind Verlage und Bibliotheken wichtige Bestandteile der Wissensversorgung in Studium und Lehre. Doch mit dem Aufkommen des E-Books verlagert sich die Recherche mehr und mehr ins Internet. Die Suchmaschine Google tritt als neuer Konkurrent der klassischen Bibliotheksrecherche auf. Aber auch Verlage müssen verstärkt auf die neuen Herausforderungen eines digitalen Buchmarktes reagieren. In Kooperation mit der Universitätsbibliothek und dem Master-Studiengang Medienmanagement diskutieren Studierende, Wissenschaftler, Bibliothekare und Verleger, wie das E-Book unseren Umgang mit Literatur verändert. Der Tagungsband stellt alle Perspektiven und Ergebnisse zum Nachlesen zusammen. KW - Elektronisches Buch KW - Studium KW - Lehre KW - Forschung KW - EDOC-Tage Weimar 2011 KW - E-Book KW - Digitaler Buchmarkt Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120223-15699 SN - 978-3-86068-454-2 N1 - Die Tagung fand am 27. - 28. Mai 2011 an der Bauhaus-Univesität Weimar im Audimax statt. PB - Verlag der Bauhaus-Universität CY - Weimar ER - TY - JOUR A1 - Hildebrand, Jörg A1 - Hecht, Kerstin A1 - Bliedtner, Jens A1 - Müller, Hartmut T1 - Advanced Analysis of Laser Beam Polishing of Quartz Glass Surfaces JF - Physics Procedia N2 - The laser beam is a small, flexible and fast polishing tool. With laser radiation it is possible to finish many outlines or geometries on quartz glass surfaces in the shortest possible time. It’s a fact that the temperature developing while polishing determines the reachable surface smoothing and, as a negative result, causes material tensions. To find out which parameters are important for the laser polishing process and the surface roughness respectively and to estimate material tensions, temperature simulations and extensive polishing experiments took place. During these experiments starting and machining parameters were changed and temperatures were measured contact-free. The accuracy of thermal and mechanical simulation was improved in the case of advanced FE-analysis. KW - Laser KW - Berührungslose Messung KW - Polieren KW - Empfindlichkeit KW - Quarzglas KW - laser; contactless measurement; quartz glass; polishing; temperature; residual stress; simulation; sensitivity Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170418-31372 UR - http://www.sciencedirect.com/science/article/pii/S1875389212025667 SP - 277 EP - 285 ER - TY - THES A1 - Nikulla, Susanne T1 - Quality assessment of kinematical models by means of global and goal-oriented error estimation techniques T1 - Anwendung globaler und zielorientierter Fehlerschätzer zur Beurteilung der Notwendigkeit einer geometrisch nicht-linearen Berechnung N2 - Methods for model quality assessment are aiming to find the most appropriate model with respect to accuracy and computational effort for a structural system under investigation. Model error estimation techniques can be applied for this purpose when kinematical models are investigated. They are counted among the class of white box models, which means that the model hierarchy and therewith the best model is known. This thesis gives an overview of discretisation error estimators. Deduced from these, methods for model error estimation are presented. Their general goal is to make a prediction of the inaccuracies that are introduced using the simpler model without knowing the solution of a more complex model. This information can be used to steer an adaptive process. Techniques for linear and non-linear problems as well as global and goal-oriented errors are introduced. The estimation of the error in local quantities is realised by solving a dual problem, which serves as a weight for the primal error. So far, such techniques have mainly been applied in material modelling and for dimensional adaptivity. Within the scope of this thesis, available model error estimators are adapted for an application to kinematical models. Their applicability is tested regarding the question of whether a geometrical non-linear calculation is necessary or not. The analysis is limited to non-linear estimators due to the structure of the underlying differential equations. These methods often involve simplification, e.g linearisations. It is investigated to which extent such assumptions lead to meaningful results, when applied to kinematical models. N2 - Die verschiedenen Methoden zur Bewertung der Modellqualität haben ein Ziel: Das passende Modell in Bezug auf Genauigkeit und Berechnungsaufwand für eine konkrete Struktur zu finden. Steht dabei die Untersuchung eines Kinematik-Modells im Vordergrund, können Modellfehlerschätzer zur Modellbewertung verwendet werden. Dieser Zusammenhang gilt, solange es sich um mechanisch motivierte Modelle handelt, bei denen die Modellhierarchie und damit das beste Modell bekannt sind. Die vorliegende Arbeit beschreibt den Weg von den einfachen Fehlerschätzern für Diskretisierungsfehler bis zu den daraus abgeleiteten Modellfehlerschätzern. Das Ziel der letztgenannten besteht in der Vorhersage von Ungenauigkeit, die durch die Verwendung eines vereinfachten anstatt des komplexen Modells entstehen. Aus den gewonnenen Informationen wird eine adaptive Modellanpassung entwickelt. Die Methoden lassen sich dabei nach verschiedenen Kriterien unterscheiden. Diese diffenzieren zwischen den verschiedenen Anwendungsbereichen, zwischen linearen und nicht-linearen Modellen sowie zwischen globalen und ziel-orientierten Fehlern. Die bislang in der Literatur hauptsächlich zu findenden Anwendungsgebiete sind die Materialmodellierung und die Dimensionsadaptivität. Im Rahmen dieser Arbeit werden nun die bekannten Methoden zur Abschätzung des Modellfehlers auf kinematische Modelle erweitert. Zudem wird die Frage, ob eine geometrisch nicht-lineare Berechnung notwendig ist oder nicht, untersucht. Aufgrund der Struktur der zugrunde liegenden Differentialgleichungen beschränken sich die Analysen auf nicht-lineare Fehlerschätzer. Da diese Methoden oft auf Vereinfachungen wie z.B. die Linearisierung der Grundgleichungen zurückgreifen, wird in der vorliegenden Arbeit untersucht, inwieweit diese Annahmen zu verwertbaren Ergebnissen führen. T3 - Schriftenreihe des DFG Graduiertenkollegs 1462 Modellqualitäten // Graduiertenkolleg Modellqualitäten - 4 KW - Model quality, Model error estimation, Kinematical model, Geometric non-linearity, Finite Element method KW - Modellqualität, Modellfehlerschätzer, Geometrisch nicht-lineare Berechnung, Kinematik Modell, Finite Elemente Methode Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120419-16161 PB - Verlag der Bauhaus-Universität Weimar CY - Weimar ER - TY - THES A1 - Krause, Haie-Jann T1 - Kallmeyer und Facilides. Eine Architektengemeinschaft im Kontext ihrer Entwicklung von konservativen Gestaltungstendenzen zur Baukunst der Moderne. N2 - Die Vorstellung des Gesamtwerkes der halleschen Architekten Julius Kallmeyer und Wilhelm Facilides, die sich Anfang der 1920er Jahre zu einer Zusammenarbeit entschlossen und eine Vielzahl interessanter Gebäude für die Saalestadt schufen, ist in der Fokussierung der Gesamtthematik der Lebens- und Werksdarstellung das Grundanliegen dieser Ausarbeitung. Dieses bisher nicht in Angriff genommene architekturgeschichtliche Anliegen beschäftigt sich mit den Ergebnissen der Bürogeschichte einer- und der Lebensgeschichte der Persönlichkeiten andererseits. Bis heute gelten die klassisch modernen Architekturen Kallmeyers & Facilides ́, gerade für den gehobenen Wohnhausbau in Halle an der Saale, als herausragende Leistungen. KW - Kallmeyer KW - Facilides KW - Moderne KW - Halle KW - Architektur KW - BDA KW - 56.62 Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20120114-15140 ER - TY - THES A1 - Stein, Peter T1 - Procedurally generated models for Isogeometric Analysis N2 - Increasingly powerful hard- and software allows for the numerical simulation of complex physical phenomena with high levels of detail. In light of this development the definition of numerical models for the Finite Element Method (FEM) has become the bottleneck in the simulation process. Characteristic features of the model generation are large manual efforts and a de-coupling of geometric and numerical model. In the highly probable case of design revisions all steps of model preprocessing and mesh generation have to be repeated. This includes the idealization and approximation of a geometric model as well as the definition of boundary conditions and model parameters. Design variants leading to more resource-efficient structures might hence be disregarded due to limited budgets and constrained time frames. A potential solution to above problem is given with the concept of Isogeometric Analysis (IGA). Core idea of this method is to directly employ a geometric model for numerical simulations, which allows to circumvent model transformations and the accompanying data losses. Basis for this method are geometric models described in terms of Non-uniform rational B-Splines (NURBS). This class of piecewise continuous rational polynomial functions is ubiquitous in computer graphics and Computer-Aided Design (CAD). It allows the description of a wide range of geometries using a compact mathematical representation. The shape of an object thereby results from the interpolation of a set of control points by means of the NURBS functions, allowing efficient representations for curves, surfaces and solid bodies alike. Existing software applications, however, only support the modeling and manipulation of the former two. The description of three-dimensional solid bodies consequently requires significant manual effort, thus essentially forbidding the setup of complex models. This thesis proposes a procedural approach for the generation of volumetric NURBS models. That is, a model is not described in terms of its data structures but as a sequence of modeling operations applied to a simple initial shape. In a sense this describes the "evolution" of the geometric model under the sequence of operations. In order to adapt this concept to NURBS geometries, only a compact set of commands is necessary which, in turn, can be adapted from existing algorithms. A model then can be treated in terms of interpretable model parameters. This leads to an abstraction from its data structures and model variants can be set up by variation of the governing parameters. The proposed concept complements existing template modeling approaches: templates can not only be defined in terms of modeling commands but can also serve as input geometry for said operations. Such templates, arranged in a nested hierarchy, provide an elegant model representation. They offer adaptivity on each tier of the model hierarchy and allow to create complex models from only few model parameters. This is demonstrated for volumetric fluid domains used in the simulation of vertical-axis wind turbines. Starting from a template representation of airfoil cross-sections, the complete "negative space" around the rotor blades can be described by a small set of model parameters, and model variants can be set up in a fraction of a second. NURBS models offer a high geometric flexibility, allowing to represent a given shape in different ways. Different model instances can exhibit varying suitability for numerical analyses. For their assessment, Finite Element mesh quality metrics are regarded. The considered metrics are based on purely geometric criteria and allow to identify model degenerations commonly used to achieve certain geometric features. They can be used to decide upon model adaptions and provide a measure for their efficacy. Unfortunately, they do not reveal a relation between mesh distortion and ill-conditioning of the equation systems resulting from the numerical model. T3 - Schriftenreihe des DFG Graduiertenkollegs 1462 Modellqualitäten // Graduiertenkolleg Modellqualitäten - 7 KW - NURBS KW - Isogeometric Analysis KW - Procedural modeling KW - Templates KW - Mesh quality Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20130212-18483 SN - 978-3-86068-488-7 PB - Universitätsverlag CY - Weimar ER -