TY - JOUR A1 - Vogl, Joseph T1 - Über Axel Maliks "skripturale Methode" N2 - Vortrag, gehalten am 20.08.2017 zur Eröffnung der Ausstellung "Die Bibliothek der unlesbaren Zeichen" im Audimax der Bauhaus-Universität Weimar T3 - Neue Bauhausvorträge - 3 KW - Kunst KW - Grafik Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171130-36683 ER - TY - THES A1 - Ehrhardt, Dirk T1 - ZUM EINFLUSS DER NACHBEHANDLUNG AUF DIE GEFÜGEAUSBILDUNG UND DEN FROST-TAUMITTELWIDERSTAND DER BETONRANDZONE N2 - Die Festigkeitsentwicklung des Zementbetons basiert auf der chemischen Reaktion des Zementes mit dem Anmachwasser. Durch Nachbehandlungsmaßnahmen muss dafür gesorgt werden, dass dem Zement genügend Wasser für seine Reaktion zur Verfügung steht, da sonst ein Beton mit minderer Qualität entsteht. Die vorliegende Arbeit behandelt die grundsätzlichen Fragen der Betonnachbehandlung bei Anwendung von Straßenbetonen. Im Speziellen wird die Frage des erforderlichen Nachbehandlungsbedarfs von hüttensandhaltigen Kompositzementen betrachtet. Die Wirkung der Nachbehandlung wird anhand des erreichten Frost-Tausalz-Widerstandes und der Gefügeausbildung in der unmittelbaren Betonrandzone bewertet. Der Fokus der Untersuchungen lag auf abgezogenen Betonoberflächen. Es wurde ein Modell zur Austrocknung des jungen Betons erarbeitet. Es konnte gezeigt werden, dass in einer frühen Austrocknung (Kapillarphase) keine kritische Austrocknung der Betonrandzone einsetzt, sondern der Beton annährend gleichmäßig über die Höhe austrocknet. Es wurde ein Nomogramm entwickelt, mit dem die Dauer der Kapillarphase in Abhängigkeit der Witterung für Straßenbetone abgeschätzt werden kann. Eine kritische Austrocknung der wichtigen Randzone setzt nach Ende der Kapillarphase ein. Für Betone unter Verwendung von Zementen mit langsamer Festigkeitsentwicklung ist die Austrocknung der Randzone nach Ende der Kapillarphase besonders ausgeprägt. Im Ergebnis zeigen diese Betone dann einen geringen Frost-Tausalz-Widerstand. Mit Zementen, die eine 2d-Zementdruckfestigkeit ≥ 23,0 N/mm² aufweisen, wurde unabhängig von der Zementart (CEM I oder CEM II/B-S) auch dann ein hoher Frost-Tausalz-Widerstand erreicht, wenn keine oder eine schlechtere Nachbehandlung angewendet wurde. Für die Praxis ergibt sich damit eine einfache Möglichkeit der Vorauswahl von geeigneten Zementen für den Verkehrsflächenbau. Betone, die unter Verwendung von Zementen mit langsamere Festigkeitsentwicklung hergestellt werden, erreichen einen hohen Frost-Tausalz-Widerstand nur mit einer geeigneten Nachbehandlung. Die Anwendung von flüssigen Nachbehandlungsmitteln (NBM gemäß TL NBM-StB) erreicht eine ähnliche Wirksamkeit wie eine 5 tägige Feuchtnachbehandlung. Voraussetzung für die Wirksamkeit der NBM ist, dass sie auf eine Betonoberfläche ohne sichtbaren Feuchtigkeitsfilm (feuchter Glanz) aufgesprüht werden. Besonders wichtig ist die Beachtung des richtigen Auftragszeitpunktes bei kühler Witterung, da hier aufgrund der verlangsamten Zementreaktion der Beton länger Anmachwasser abstößt. Ein zu früher Auftrag des Nachbehandlungsmittels führt zu einer Verschlechterung der Qualität der Betonrandzone. Durch Bereitstellung hydratationsabhängiger Transportkenngrößen (Feuchtetransport im Beton) konnten numerische Berechnungen zum Zusammenspiel zwischen der Austrocknung, der Nachbehandlung und der Gefügeentwicklung durchgeführt werden. Mit dem erstellten Berechnungsmodell wurden Parameterstudien durchgeführt. Die Berechnungen bestätigen die wesentlichen Erkenntnisse der Laboruntersuchungen. Darüber hinaus lässt sich mit dem Berechnungsmodell zeigen, dass gerade bei langsam reagierenden Zementen und kühler Witterung ohne eine Nachbehandlung eine sehr dünne Randzone (ca. 500 µm – 1000 µm) mit stark erhöhter Kapillarporosität entsteht. N2 - The hardening of cement concrete is based on the chemical reaction of cement and water. Therefore, the ensuring of sufficient amount of water in concrete is essential. All these measures are referred as curing of concrete. This dissertation provides a basic consideration of curing of concrete for concrete pavements. In this regard the using of cements with slow strength development, e.g. cements with blast furnace slag is the main topic. The effectiveness of curing was evaluated on the basis of the freeze-thaw de-icing resistance and the microstructure of hardened outer concrete surface. Concrete surfaces with textured mortar are on the focus. The results were used to develope a model of the drying of young concrete. It could be shown, that the outer concrete surface does not dry during the first drying phase (called capillary phase). Instead the concrete is drying evenly over the high of the concrete sample during the capillary drying phase. A fast drying of the outer concrete surface only takes place after the capillary drying phase. Based on all results a nomogram (for road concrete) was created for an estimation of the duration of the capillary drying phase. If there is no curing after the capillary drying phase the concrete with use of slowly reacting cement has a great risk for a harmful drying of outer concrete surface. In this case such a concrete shows a very poor freeze thaw de-icing resistance. By using cements with a 2 day-compressive strength ≥ 23,0 N/mm² a good freeze thaw de-icing resistance could assure, despite no or a poor curing was applied. This criterion can be used to estimate the usability of cements with granulated blast furnace slag when a great freeze thaw de-icing resistance is essential. There could also be used a cement with lower 2 day-compressive strength. In this case a good curing has to be assured. Spraying of liquid curing compounds according to TL NBM-StB is suitable for curing concrete pavements. The curing compound should not be sprayed on a concrete surface with any visible water film. The effectiveness of curing compounds is equal to a five days long wet curing in consideration of applying the curing compound at the right time. Otherwise there is some negative influence when the spraying of curing compounds starts too early. Consideration about the right application time of curing compounds is more important for low temperatures because the concrete bleeds much longer due to the slower cement reaction at low temperatures. It was possible to create a numerical model which accounts the interaction between drying, curing and development of microstructure by providing hydration dependent transport parameters (water transport in concrete). The model was used for a parameter study. It could be shown that the combination of cements with slow strength development and low ambient temperatures leads to a thin surface zone (500 µm – 1000 µm) with very high capillary porosity. KW - Beton KW - Zement KW - Nachbehandlung KW - Modellbildung KW - Nachbehandlungsmittel KW - Straßenbeton KW - Frost-Tausalz-Widerstand KW - curing compounds KW - concrete pavements Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171120-36889 ER - TY - JOUR A1 - Assmann, Aleida T1 - Welche Zukünfte? N2 - Vortrag, gehalten am 20.04.2017 zur Einführung von Prof. Dr. Winfried Speitkamp in das Amt des Präsidenten der Bauhaus-Universität Weimar T3 - Neue Bauhausvorträge - 1 KW - Fortschritt KW - Ungewissheit KW - Nachhaltigkeit Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171130-36136 ER - TY - JOUR A1 - Pervyshin, G.N. A1 - Yakovlev, G.I. A1 - Gordina, A.F. A1 - Keriene, J. A1 - Polyanskikh, I.S. A1 - Fischer, Hans-Bertram A1 - Rachimova, N.R. A1 - Buryanov, A.F. T1 - Water-resistant Gypsum Compositions with Man-made Modifiers JF - Procedia Engineering N2 - The work has studied the structure and properties of gypsum compositions modified with the manmade modifier based on metallurgical dust and multi-walled carbon nanotubes. The results show that changing the structure of solid gypsum leads to the increase in bending and compressive strength by 70,5% and 138% correspondingly, the water resistance increasing and the softening factor reaching 0,85. Modifying gypsum composition with complex additive leads to the formation of amorphous structures based on calcium hydrosilicates on the surface of primary gypsum crystallohydrates that bond gypsum crystals and reduce the access of water. KW - Gips KW - Wasserbeständigkeit KW - Mikrostruktur KW - gypsum, metallurgical dust, multi-walled carbon nanotubes, water resistance, calcium hydrosilicates, X-ray analyze, microstructure. Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170425-31580 SP - 867 EP - 874 ER - TY - THES A1 - Heidenreich, Manuel T1 - Untersuchungen zur Sauerstoffbereitstellung mit Perowskit- Keramik-Schüttungen in einem Festbett-Reaktor N2 - Diese Arbeit belegt, dass die Belastungen auf reversibel arbeitende keramische Materialien sehr gering ausfallen. Die regenerative Sauerstoffbereitstellung stellt damit grundsätzlich niedrigere Anforderungen an die keramischen Perowskit-Materialien zur Sauerstofferzeugung als die Membrantechnologie. Das Absinken der Diffusionskoeffizienten bei niedrigen Temperaturen ist deutlich weniger nachteilig als bei den Membranen die vergleichbare Materialien nutzen. Dies konnte gezeigt werde, indem mit der die O 2 -Entladetechnik und -Beladetechnik im Vergleich zur O 2 -Abtrennung durch keramische Membranen bei vergleichsweise niedrigen Temperaturen bereits große O 2 -Mengen erzeugt werden können. Infolge der niedrigen Temperaturen bestehen keine Probleme mit Reaktionen zwischen dem sauerstoffbereitstellenden Material und den Reaktorwerkstoffen. Dadurch gestaltet sich die Einbindung und Nutzung von Festbett-Schüttungen denkbar einfach. Im Vergleich dazu sind die Anbindung und der Betrieb von dünnen keramischen Membranen in einem Reaktor deutlich aufwendiger. Es ist weniger Peripherie und verfahrenstechnischer Aufwand zur Sauerstoffabtrennung durch reversibel arbeitende Materialien nötig als bei der kryogenen Luftzerlegung, der Druckwechseladsorption oder den Membrantechnologien. Die regenerative Sauerstoffbereitstellung kann sowohl bei neuen als auch bestehenden Anlagen, die Sauerstoff benötigen implementiert werden. Damit ist es möglich den Transport des Sauerstoffs entfallen zu lassen. Eine partielle Phasenumwandlung des BSCF8020 bei erhöhter Temperatur und hohem Sauerstoffangebot spielt für die regenerative Sauerstoffbereitstellung eine untergeordnete Rolle, da die nötigen Zieltemperaturen (450 ggf. bis 650 °C) zur O 2 -Beladung und -Entladung niedriger sind, als der Temperaturbereich in dem die Zersetzung auftreten kann (750 bis 800 °C). Des Weiteren ist die Zeitspanne (O 2 -Beladungsteilzyklus) in der das BSCF8020 ausreichend hohen Sauerstoffgehalten (p O2 > 10 -3 bar) ausgesetzt ist, zu kurz um diese Umwandlungen zu vollziehen. Der O 2 -Entladungsteilzyklus sorgt zusätzlich immer dafür, dass sich u. U. beginnende Zersetzung zurückbildet, da die kubische Phase in Richtung niedrigerer p O2 stabilisiert wird. Es konnte belegt werden, dass die elektronische Steuerung des zyklischen Sauerstoffausbaus und -einbaus beherrschbar ist. Der hohe Abtrenngrad der keramischen Materialien führt dazu, dass der Sauerstoff elektrolytisch rein zu Verfügung gestellt wird. Grundsätzlich sind weitere Forschungen zur Steigerung der Sauerstoffmengen, die pro eingesetzter Masseeinheit an Keramik gewonnen werden können, immer anzustreben, da damit u. U. der Materialeinsatz weiter gesenkt oder auch die energetischen Aufwendungen weiter reduziert werden können. Bei dem, für die multizyklischen Untersuchungen dieser Arbeit ausgewählten BSCF8020(SVT) hat die Cobalt-Komponente mit ca. 80 % den überwiegenden Kostenanteil am Sauerstoff bereitstellenden Material. BSCF-Keramiken mit höherem Eisen-Anteil sollten für multizyklische Anwendungen in Festbett-Reaktoren einer vertiefenden Charakterisierung unterzogen werden, um weitere geeignete Perowskite mit niedrigen Materialkosten zu erschließen. KW - Perowskit KW - Sauerstoff KW - Keramik KW - Festbett KW - Schüttung KW - BSCF KW - LSCF KW - SrMnO3 KW - CSMF KW - Dynamische Messungen Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171027-36077 ER - TY - JOUR A1 - Zander, Steffi A1 - Wetzel, Stefanie A1 - Kühl, Tim A1 - Bertel, Sven T1 - Underlying Processes of an Inverted Personalization Effect in Multimedia Learning – An Eye-Tracking Study JF - Frontiers in Psychology N2 - One of the frequently examined design principles recommendations in multimedia learning is the personalization principle. Based on empirical evidence this principle states that using personalised messages in multimedia learning is more beneficial than using formal language (e.g. using ‘you’ instead of ‘the’). Although there is evidence that these slight changes in regard to the language style affect learning, motivation and the perceived cognitive load, it remains unclear, (1) whether the positive effects of personalised language can be transferred to all kinds of content of learning materials (e.g. specific potentially aversive health issues) and (2) which are the underlying processes (e.g. attention allocation) of the personalization effect. German university students (N= 37) learned symptoms and causes of cerebral haemorrhages either with a formal or a personalised version of the learning material. Analysis revealed comparable results to the few existing previous studies, indicating an inverted personalization effect for potentially aversive learning material. This effect was specifically revealed in regard to decreased average fixation duration and the number of fixations exclusively on the images in the personalised compared to the formal version. This result can be seen as indicators for an inverted effect of personalization on the level of visual attention. KW - Lernen KW - multimedia learning KW - Computerunterstütztes Lernen KW - Multimedia KW - personalization effect KW - eye-tracking KW - cognitive load KW - multimedia design principles KW - OA-Publikationsfonds2017 Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20180312-37342 UR - https://www.frontiersin.org/articles/10.3389/fpsyg.2017.02202/full VL - 2017 IS - Volume 8, Article 2202 SP - 1 EP - 16 ER - TY - JOUR A1 - Zhang, Chao A1 - Hao, Xiao-Li A1 - Wang, Cuixia A1 - Wei, Ning A1 - Rabczuk, Timon T1 - Thermal conductivity of graphene nanoribbons under shear deformation: A molecular dynamics simulation JF - Scientific Reports N2 - Tensile strain and compress strain can greatly affect the thermal conductivity of graphene nanoribbons (GNRs). However, the effect of GNRs under shear strain, which is also one of the main strain effect, has not been studied systematically yet. In this work, we employ reverse nonequilibrium molecular dynamics (RNEMD) to the systematical study of the thermal conductivity of GNRs (with model size of 4 nm × 15 nm) under the shear strain. Our studies show that the thermal conductivity of GNRs is not sensitive to the shear strain, and the thermal conductivity decreases only 12–16% before the pristine structure is broken. Furthermore, the phonon frequency and the change of the micro-structure of GNRs, such as band angel and bond length, are analyzed to explore the tendency of thermal conductivity. The results show that the main influence of shear strain is on the in-plane phonon density of states (PDOS), whose G band (higher frequency peaks) moved to the low frequency, thus the thermal conductivity is decreased. The unique thermal properties of GNRs under shear strains suggest their great potentials for graphene nanodevices and great potentials in the thermal managements and thermoelectric applications. KW - Wärmeleitfähigkeit KW - Graphen KW - Schubspannung Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170428-31718 ER - TY - THES A1 - Yuli, Nensi Golda T1 - The Spatial Concept at Moslem Settlements in Current Context of Modern Indonesia Using Phenomenology Method . Case Study: Pathok Negoro Area in Yogyakarta, Indonesia N2 - Settlement is human place to live and do various activities (Finch, 1980). Concept of settlement layout is closely associated with human and a set of thoughts and behaviors. In this case, idea of pattern of activities in a society that is core of a culture becomes main factor in process of formation of houses and environment in a settlement. Factors which affecting form (physical) of architecture in a settlement environment are socio-cultural, economic, and religious determinant factor that manifested architectural realization (Rapoport, 1969). Yogyakarta as the continuation of kingdom city in the Java Island finally exists as an Islamic kingdom that still remain to survive up to now. Impacts of this issue is appearance of various Moslem settlements to support typical character of an Islamic Kingdom. Mlangi is an area of oldest Moslem settlements in Yogyakarta has not been explored in details for progress especially in physical glasses recently. Everything basic group and individual who arrange houses and residences, starts from how it has spatial concept alone. Although concept is a very abstract thing to explain in details, but its existence can be detected by how they created their physical environment. This research conducted by these research questions: (1) What are spatial concepts owned by people in Mlangi and (2) How do spatial concepts owned by the people affect the settlements pattern? Process to search spatial concept owned by the people in Moslem residence, making Mlangi as study area, was approached by using phenomenological research method. The researcher have to self-involved directly in unstructured interviews, but remained in guideline framework of in interviews to make research process effective. Fistly, the researcher interviewed the key person, they are the head of Mlangi administration (pak Dukuh) in Mlangi and Sawahan. They were then give advices to who was capable person that could draw the spatial concept and had many story and knew the history of the settlements. Step by step of interview guided from one informant to next informant when the information had been told repeatedly. The next informant based on the last informant advice or who had close relationship with the last theme appeared. To complete the narration and draw the result of interview, researcher have to add additional information with photograph and descriptive picture that can be draw the settlement empirically. In process, 17 information units which found in field were consistent with sequence of interview events and flowing of theme to theme associated with Moslem residence of residence. Finally the interviews succeeded in abstracting 16 themes that may be classified into historic, socio-cultural, and spatial-concept dimensions in Mlangi. Process of analysis to find spatial concept owned by the people in Moslem settlements was carried out by dialogue of themes to find available substantive relationship. Four concepts successfully analyzed consist of concepts of personage, concept of religious implementation, concept of Jero-Jaba and concept of Interest. The four concepts are really associated with one and others in understanding how spatial concept owned by the people affects residence they occupy. Yet, concept of Jero-Jaba bases all concepts of people in Mlangi . This concept can be used to draw red yarn on how they utilize communal spaces in residence and layout rooms of their individual houses. This concept also eternalize residence patterns existing in Mlangi now where residence does not experience many changes from starting of this residence existence (from detection of generation currently still living), namely residence patterns concentrate on orientation to Masjid Pathok Negoro of Mlangi. This research was opening the potential research area, at least for the sociology, anthropology and demography research interest. So many unique character in Mlangi if looked at from how they maintain their spatial concept and manifested in their daily activities. How the people will concern only for the religious activities and the economic concern only for survival aspect in live. Keywords: spatial concept, moslem settlements, phenomenology method, Indonesia, KW - Siedlung KW - spatial concept KW - Muslim KW - moslem settlements KW - phenomenology method KW - Indonesia Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170419-31257 ER - TY - THES A1 - Podlaszewska, Rizky Suci Ammalia T1 - The Placemaking of Destination. Localization and Commoditization process of Urban Tourism. Study case Palembang Indonesia N2 - This research addresses the discourse of tourism as a tool for place-making of urban destination. Relevant to the study of place-making is the analysis of the commoditization and localization process dependent upon the appropriation of urban landscape and local cultures. In the research, localization is interpreted as the act of determining the attributes of locality, while commoditization is defined as the process by which local attributes that have commercial potential end up in becoming tourism commodity. Following this, the commoditization of intrinsic cultural value is disseminated within a branding strategy and intervention reflecting social and political relations. Therefore, the research suggests that tourism place-making has not only been constructed through the top-down regulatory body, but has been also generated through the attributes of its locality. By utilizing the critical and constructivist paradigm, the research depicts the conditions of the localization and commoditization process in establishing the base line of its realization within the symbolic economy. Thus, a qualitative case study approach was adopted. The study area of this dissertation is Palembang, as one of the capital cities in Indonesia advancing in its overall urban development. To investigate urban tourism as a tool for development strategy, it is useful to investigate the role of tourism which embodies (1) spatial transformation; how tourism gives significant impacts on urban form, and (2) the socio-cultural aspect; how neighbourhood is related to tourism industry. The findings suggest that tourism place-making involves the reciprocity of urban dynamics: cities take on tourism as a reference model of development, and tourist areas adopt the proliferation of cultural lifestyle to meet the industry’s demands. KW - Urbanistik Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171201-36995 ER - TY - THES A1 - Peters, Simone T1 - The Influence of Power Ultrasound on Setting and Strength Development of Cement Suspensions N2 - Ein aktuelles Thema in der Forschung der Betonindustrie ist die gezielte Steuerung des Erstarrens und der Entwicklung der (Früh)Festigkeit von Betonen und Mörteln. Aus ökonomischer Sicht sind außerdem die Reduktion der CO2-Emission und die Schonung von Ressourcen und Energie wichtige Forschungsschwerpunkte. Eine Möglichkeit zum Erreichen dieser Ziele ist es, die Reaktivität/Hydratation der silikatischen Klinkerphasen gezielt anzuregen. Neben den bereits bekannten Möglichkeiten der Hydratationsbeschleunigung (u.a. Wärmebehandlung, Zugabe von Salzen) bietet die Anwendung von Power-Ultraschall (PUS) eine weitere Alternative zur Beschleunigung der Zementhydratation. Da bis zum jetzigen Zeitpunkt noch keine Erfahrungen zum Einsatz von PUS in der Zementchemie vorliegen, sollen mit der vorliegenden Arbeit grundlegende Kenntnisse zum Einfluss von PUS auf das Fließ- und Erstarrungsverhalten von Zementsuspensionen erarbeitet werden. Dazu wurde die Arbeit in fünf Hauptuntersuchungsabschnitte aufgeteilt. Im ersten Teil wurden optimale PUS-Parameter wie Amplitude und Energieeintrag ermittelt, die eine effiziente Beschleunigung der Portlandzement(CEM I)hydratation bei kurzen Beschallzeiten und begrenzter Zementleimtemperaturerhöhung erlauben. Mit Hilfe unabhängiger Untersuchungsmethoden (Bestimmung des Erstarrungsbeginns, der Festigkeitsentwicklung, zerstörungsfreier Ultraschallprüfung, isothermer Wärmeflusskalorimetrie, hochauflösender Rasterelektronmikroskopie (REM) wurde die Wirkung von PUS auf den Hydratationsverlauf von CEM I-Suspensionen charakterisiert. Die Ergebnisse zeigen, dass die Behandlung von CEM I-Suspensionen mit PUS grundsätzlich ein beschleunigtes Erstarren und eine beschleunigte (Früh)Festigkeitsentwicklung hervorruft. Anhand von REM-Untersuchungen konnte eindeutig nachgewiesen werden, dass die Beschleunigung der CEM I-Hydratation mit einer beschleunigten Hydratation der Hauptklinkerphase Alit korreliert. Auf Grundlage dieser Erkenntnisse wurden die Ursachen der Aktivierung der Alithydratation untersucht. Dazu wurden Untersuchungen an Einzelsystemen des CEM I (silikatische Klinkerphase) durchgeführt. Es ist bekannt, das die Hydratation der Hauptklinkerphase Alit (in der reinen Form Tricalciumsilikat 3CaO*SiO2; C3S) durch Lösungs-/Fällungsreaktionen (Bildung von Calcium-Silikat-Hydrat Phasen, C-S-H Phasen) bestimmt wird. Mit Hilfe von Untersuchungen zur Auflösung (C3S) und Kristallbildung (C-S-H Phasen) in Lösungen und Suspensionen (Aufzeichnung der elektrischen Leitfähigkeit sowie Bestimmung der Ionenkonzentrationen der wässrigen Phase, REM-Charakterisierung der Präzipitate) wurde die Beeinflussung dieser durch eine PUS-Behandlung charakterisiert. Die Ergebnisse zeigen, dass in partikelfreien Lösungen (primäre Keimbildung) eine PUS-Behandlung keinen Einfluss auf die Kinetik der Kristallisation von C-S-H Phasen hervorruft. Das heißt, auch die durch PUS eingetragene Energie reicht offensichtlich nicht aus, um in Abwesenheit von Oberflächen die C-S-H Phasen Bildung zu beschleunigen. Das weist darauf hin, dass die Bildung von C-S-H Phasen nicht durch eine Beschleunigung von Ionen in der Lösung (erhöhte Diffusion durch Anwendung von PUS) hervorgerufen wird. Eine Beschleunigung des Kristallisationsprozesses (Keimbildung und Wachstum von C-S-H Phasen) durch PUS wird nur in Anwesenheit von Partikeln in der Lösung (Suspension) erzielt. Das belegen Ergebnisse, bei denen die Bildung erster C-S-H Phasen bei geringer Übersättigung (heterogene Keimbildung, in Anwesenheit von Oberflächen) erfolgt. Unter diesen Bedingungen konnte gezeigt werden, dass PUS innerhalb der ersten 30 Minuten der Hydratation eine erhöhte Fällung von ersten C-S-H Phasen bewirkt. Diese fungieren dann vermutlich während der Haupthydratation als Keim bzw. geeignete Oberfläche zum beschleunigten Aufwachsen von weiteren C-S-H Phasen. Weiterhin ist vorstellbar, dass (in Analogie zu anderen Bereichen der Sonochemie) PUS durch Kavitation Schockwellen hervorruft, welche Partikel und wässriges Medium beschleunigen und damit erhöhte Partikelbewegungen und -kollisionen induziert. Dies wiederum bewirkt, dass die anfänglich auf der C3S-Oberfläche gebildeten C-S-H Phasen teilweise wieder entfernt werden. Damit ist das Inlösunggehen von Ca- und Si-Ionen aus dem C3S weiterhin möglich. Um den genauen Mechanismus weiter zu charakterisieren sollten mit geeigneten Methoden weitere Untersuchungen durchgeführt werden. Im zweiten Teil der Arbeit wurde der Einfluss von PUS auf das Fließverhalten von CEM I-Suspensionen untersucht. Aus der Anwendung von PUS in anderen technischen Bereichen sind unter anderem Effekte wie das Entlüften, das Homogenisieren und das Dispergieren von Suspensionen und Emulsionen mittels PUS bekannt. Mit Hilfe der Bestimmung des Luftporengehaltes, Sedimentationsversuchen und cryo-SEM Untersuchungen wurde der Einfluss von PUS auf CEM I-Suspensionen charakterisiert. Die Ergebnisse belegen, dass durch PUS eine verbesserte Homogenität und Dispergierung der CEM I-Suspension erzielt wird. Damit wird für CEM I-Suspensionen unterschiedlichster w/z-Werte eine verbesserte Fließfähigkeit festgestellt. Ergebnisse der Bestimmung von Ausbreitmaßen und Trichterauslaufzeiten zeigen, dass PUS einen direkten Einfluss vor allem auf die Viskosität der CEM I-Suspensionen besitzt. Werden Fließmitteln (FM) der CEM I-Suspension zugegeben, wird nicht in jedem Fall eine verbesserte Fließfähigkeit festgestellt. Hier scheint unter bestimmten Voraussetzungen (w/z-Wert, FM-Gehalt, PUS) die Reaktion zwischen Aluminat- und Sulfatphase des Klinkers gestört. Zur eindeutigen Klärung dieses Sachverhaltes bedarf es jedoch weiterer quantitativer Untersuchungen zum Reaktionsumsatz. Im dritten Teil der Arbeit wurden die am CEM I gewonnenen Erkenntnisse zum Einfluss von PUS auf die Hydratation an Portland-Hüttensand(HÜS)-Zement-Systemen verifiziert. Dafür wurden auch in diesem Teil der Arbeit zunächst die optimalen PUS-Parameter festgelegt und der Einfluss auf das Erstarrung- und Erhärtungsverhalten dokumentiert. Untersuchungsmethoden sind unter anderem die Bestimmung des Erstarrungsbeginns und der (Früh)Festigkeitsentwicklung, Temperaturaufzeichnungen und isothermale Wärmeflusskalorimetrie sowie REM. Die Ergebnisse zeigen, dass auch die Reaktion von HÜS-Zementen durch PUS beschleunigt wird. Weiterführende Untersuchungen belegen, dass die erzielte Beschleunigung vorwiegend auf der Beschleunigung der Alitkomponente des CEM I beruht. Im Fokus der Teile vier und fünf dieser Arbeit stand die Anwendbarkeit der PUS-Technik unter praktischen Bedingungen. Zum einen wurde die Anwendbarkeit von PUS in fertig gemischten Mörteln beurteilt. Anhand des Vergleichs wichtiger Frisch- und Festmörteleigenschaften unterschiedlich hergestellter Mörtel (beschallt im Anschluss an konventionelle Mischtechnik, beschallt im Anschluss an Suspensionsmischtechnik mit anschließender Zumischung der Gesteinskörnung und nicht beschallt) wird gezeigt, dass im Fall von Mörteln mit hohem Leimanteil eine durch PUS induzierte beschleunigte Festigkeitsentwicklung auch mit herkömmlichen Mischabläufen (ohne aufwendige Umstellung des Mischprozesses) möglich ist. Abschließend wird untersucht, ob der Herstellungsprozess von Wandbauteilen im Fertigteilwerk durch den Einsatz von PUS optimiert werden kann und ob eine Einbindung der PUS-Technik in den Fertigungsprozess ohne größeren Aufwand möglich ist. Dazu wurden in einem ersten Schritt die Frisch- und Festbetoneigenschaften eines aktuell angewendeten selbstverdichtenden Betons im Labormaßstab (Mörtel) in Abhängigkeit einer PUS-Behandlung dokumentiert und mit der seiner unbeschallten Referenz verglichen. Aufgrund der durch PUS verursachten verbesserten Fließ- und Festigkeitseigenschaften kann die beschallte Mörtelrezeptur hinsichtlich Fließmittelgehalt und Dauer der Wärmebehandlung optimiert werden. Somit werden ca. 30 % der Fließmittelzugabe und 40 % der Dauer der Wärmebehandlung eigespart. Eine Einbindung der PUS-Technik in das betrachtete Fertigteilwerk ist nach Überprüfung der konstruktiven Gegebenheiten der Fertigungsstrukturen ohne größeren Aufwand möglich. KW - Cement KW - Power Ultrasound KW - Acceleration KW - Tricalcium silicate Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170210-27446 SN - ISBN 978-3-00-055602-9 ER - TY - JOUR A1 - Chubukov, A. A1 - Kapitanov, Valeriy A1 - Monina, Olga A1 - Silyanov, Valentin A1 - Brannolte, Ulrich T1 - Simulation of Regional Mortality Rate in Road Accidents JF - Transportation Research Procedia 20 N2 - The paper gives the results of scientific research, which, being based on probabilistic and statistical modeling, identifies the relationship of certain socio-economic factors and the number of people killed in road accidents in the Russian Federation regions. It notes the identity of processes in various fields, in which there is loss of life. Scientific methods and techniques were used in the process of data processing and study findings: systematic approach, methods of system analysis (algorithmization, mathematical programming) and mathematical statistics. The scientific novelty lies in the formulation, formalization and solving problems related to the analysis of regional road traffic accidents, its modeling taking into account the factors of socio-economic impact. KW - Modellierung KW - correlation; factors; loss of life in accidents; modeling; Road traffic accidents; socio-economic aspect; statistical analysis Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170331-30956 UR - http://www.sciencedirect.com/science/article/pii/S2352146517300315 SP - 112 EP - 124 ER - TY - JOUR A1 - Eckardt, Frank T1 - Sich in der ‚Krise’ einrichten? Rezension zu Jörg Friedrich, Peter Haslinger, Somon Takasaki und Valentina Forsch (Hg.) (2017): Zukunft: Wohnen. Migration als Impuls für die kooperative Stadt. Berlin: jovis. JF - sub/urban. Zeitschrift für kritische Stadtforschung N2 - Das rezensierte Buch stellt die zweite Publikation von Jörg Friedrich und seinem Team zum Thema Architektur und Flüchtlinge dar. Darin werden vor allem Entwurfsvorschläge für eine hybride Stadt vorgestellt, für die eine multifunktionale Nutzung von Raum als Grundidee vorgeschlagen wird. Zudem diskutieren konzeptionelle Beiträge des Bandes, wie nach der ‚Willkommenskultur’ im Jahr 2015 eine längerfristige Perspektive für Integration eingenommen werden kann. Der Band fordert ein größeres Engagement der Architektur und einen interdisziplinären Diskurs ein, der sich der vielfältigen Aufgaben der Flüchtlingsintegration annimmt. KW - Stadtforschung KW - Flüchtlinge KW - OA-Publikationsfonds2017 Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171130-37139 UR - http://www.zeitschrift-suburban.de/sys/index.php/suburban/issue/view/36 VL - 2017 IS - Band 5, Heft 3 SP - 181 EP - 184 ER - TY - JFULL ED - Engell, Lorenz ED - Siegert, Bernhard T1 - Schwerpunkt Operative Ontologien N2 - Die vorliegende Ausgabe der Zeitschrift für Medien- und Kulturforschung verdankt sich einem Experiment. In Experimenten, wenigstens soweit es sich zunächst um künstlerische und philosophische Prozeduren handelt, geht es, frei nach Jean-François Lyotard, darum, herauszufinden, welchen Regeln die Verfahren selbst folgen, während man sie bereits anwendet, während man also danach sucht, welchen Regeln man folgt. In eben diesem Sinne bemüht sich das vorliegende Heft um eine Klärung des Verfahrens »operativer Ontologien«. Während in der Kunst das Werk selbst als eine dynamische Instanz der experimentellen Prozedur gelten kann, haben die Herausgeber hier jedoch einen etwas anderen Weg eingeschlagen, indem sie nämlich verschiedene Texte in einem experimentellen Bezugsrahmen angefragt – und wunderbarerweise auch erhalten haben. Wunderbarerweise deshalb, weil sowohl in Philosophie und Kunst als auch in den Wissenschaften jedes Experiment nicht nur mit der Freude am Aufbauen und Einstellen der Apparaturen, Instrumente und Dispositive, am Basteln also, sondern auch mit erheblicher Zumutung und vielleicht einem kleinen Wagnis verbunden ist. Zudem ist zum Zeitpunkt seiner Unternehmung über seinen Ausgang noch nicht das Geringste bekannt. Im vorliegenden Fall, denn die Veröffentlichung ist selbstverständlich das eigentliche Experiment, wissen wir alle also bis jetzt nichts über den Ausgang. KW - Medienwissenschaft KW - Kulturwissenschaft Y1 - 2017 U6 - http://dx.doi.org/10.28937/ZMK-8-2 SN - 2366-0767 N1 - Lizenz CC-BY-NC-SA 3.0 VL - 2017 IS - 8.2017, Heft 2 PB - Felix Meiner Verlag CY - Hamburg ER - TY - JFULL ED - Engell, Lorenz ED - Siegert, Bernhard T1 - Schwerpunkt Inkarnieren N2 - Der Themenschwerpunkt des vorliegenden Heftes der Zeitschrift für Medien- und Kulturforschung wird bestritten von Autoren, die der DFG-Forschergruppe »Medien und Mimesis« angehören, die an der Bauhaus-Universität Weimar angesiedelt, aber zusätzlich über die Universitäten Basel, Bielefeld, Bochum, München und Zürich verteilt ist. Die Forschergruppe untersucht Mimesis als Kulturtechnik vor dem Hintergrund aktueller Entwicklungen in der Medienforschung, die Praktiken und Operationsketten als vorgängig gegenüber den aus ihnen hervorgehenden Subjekt-Objekt-Dichotomien bzw. Subjekt-Werkzeug-Artefakt-Kausalitäten ansehen. Die Auffassung von Mimesis als einer vielgestaltigen Kulturtechnik geht über die in den Kultur- und Literaturwissenschaften ebenso wie in der Philosophie dominierende ästhetische und epistemische Betrachtung der Mimesis hinaus und stellt das geschichtsphilosophische Selbstverständnis der Moderne als eine grundlegend a-mimetische kulturelle und soziale Formation infrage. Mimesis und imitatio werden nicht länger in die Perspektive einer zu ü berwindenden Vorgeschichte der Idee des schöpferischen Menschen und seiner Werkherrschaft gestellt (Blumenberg). Anstatt die Mimesis in einen Gegensatz zur modernen Technik und der auf ihr beruhenden Zivilisation zu manövrieren und das konstruktivistische Selbstverständnis der Neuzeit kulturell zu verallgemeinern und absolut zu setzen, gehen die Projekte der Forschergruppe auf unterschiedlichen Feldern den seinsverändernden, transformatorischen Wirkungen medial gekoppelter mimetischer Praktiken und Verhaltensweisen zwischen dem 15. und dem 21. Jahrhundert nach. ... KW - Medienwissenschaft KW - Kulturwissenschaft Y1 - 2017 U6 - http://dx.doi.org/10.28937/ZMK-8-1 SN - 2366-0767 N1 - Lizenz CC-BY-NC-SA 3.0 VL - 2017 IS - 8.2017, Heft 1 PB - Felix Meiner Verlag CY - Hamburg ER - TY - JOUR A1 - Schuch, Kai A1 - Kaps, Christian T1 - Reifungs- und Strukturbildungsprozesse bei Bindern mit wässrigen Alkalisilikat-Lösungen N2 - Durch Reifungs- und Strukturbildungsprozesse kann es bei silikatischen und alumosilikatischen Bindern zu Rissbildung bei behinderter Verformung, Festigkeitsverlust und somit Verlust der Dauerhaftigkeit kommen. Die Bewertung dieser Prozesse erfolgt an silikatischen Materialien mit einem Ausblick auf die alumosilikatischen Binder. KW - Alkalisilikat KW - Wasserglas KW - Bindemittel KW - Silikat KW - Wasserglas KW - Reifungsprozess KW - Strukturbildungsprozess KW - Alumosilikat KW - Silikat Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170728-32682 UR - https://e-pub.uni-weimar.de/opus4/frontdoor/index/index/docId/3267 SP - 1 EP - 17 ER - TY - JOUR A1 - Schuch, Kai A1 - Kaps, Christian T1 - Reifungs- und Strukturbildungsprozesse bei Bindern mit wässrigen Alkalisilikat-Lösungen N2 - Durch Reifungs- und Strukturbildungsprozesse kann es bei silikatischen und alumosilikatischen Bindern zu Rissbildung bei behinderter Verformung, Festigkeitsverlust und somit Verlust der Dauerhaftigkeit kommen. Die Bewertung dieser Prozesse erfolgt an silikatischen Materialien mit einem Ausblick auf die alumosilikatischen Binder KW - Alkalisilikat KW - Wasserglas KW - Bindemittel KW - Silikat KW - Wasserglas KW - Reifungsprozess KW - Strukturbildungsprozess KW - Alumosilikat KW - Silikat Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170718-32675 UR - https://e-pub.uni-weimar.de/opus4/frontdoor/index/index/docId/3268 SP - 1 EP - 17 ER - TY - JOUR A1 - Metzner, Steffen T1 - Regional Influences on Yields of Logistics Properties N2 - By allocating real estate investments into the logistics sector, investors highly participate in the economic development of the respective country or city. However, the submarket is very cyclical and special economic influences – such as growing online trade and new logistic networks – affect the performance of the properties. Important parameters on the potential returns are found not only within the real estate market, but also within the global economy and the development of specific industries. This paper aims at examining factors affecting the performance of logistics properties. Expected dependencies between macroeconomic factors and real estate economic indicators are examined for six major European logistics locations using econometric models, especially correlation and regression. Data series over a period of 25 years were used. The construction of an econometric model was an iterative process integrating both the statistical result and the economic causality. KW - Grundstück KW - Investition KW - Rendite KW - Logistik KW - Wirtschaft KW - Market Analysis KW - Logistics Properties KW - Regional factors of influence KW - Real Estate Portfolio Management KW - Forecasting Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170516-31817 SP - 1 EP - 14 ER - TY - THES A1 - Arboleda, Pablo T1 - Reckoning with Incompiuto Siciliano: Unfinished Public Works as Modern Ruins and All which it Entails N2 - Since the end of the 1950s, Italy has focused part of its modernization on the erection of public works. Due to corruption, mafia, and further malpractice, this form of development has occasionally failed, producing a high number of constructions that have remained unfinished for decades. In 2007, the group of artists Alterazioni Video constructed an informal survey in the form of an on-line tool open to public contributions, which revealed that there are 395 unfinished public works in Italy from which 156, approximately 39.5%, are located in Sicily alone. In view of such a statistic, Alterazioni Video opted to coin the term ‘Incompiuto Siciliano’ – literally ‘Sicilian Incompletion’ – to refer to unfinished public works as a formal architectural style. This re-interpretation, which aims to convey the recovered dignity of these ‘modern ruins’, considers unfinished public works a type of heritage with the potential to represent the entirety of Italian society. Furthermore, it goes as far as to say an unfinished public work is ‘Incompiuto Siciliano’ despite being located in another of the Italian regions. This doctoral dissertation embraces the artists’ argument to develop a complete study of Incompiuto Siciliano by embedding this architectural style/artistic project within the main debates on modern ruins at present. This is important because it is expected to contribute to the revalorization and eventual recommissioning of unfinished sites by validating Incompiuto Siciliano in the realm of academia. Furthermore, this work aspires to be a worthwhile source of information for future investigations dealing with cultural interpretations of incompletion in any other context – a not unreasonable goal considering how unfinished works are one of the key urban topics after the 2008 financial crisis. Hence, this doctoral dissertation uses Incompiuto Siciliano to discuss a different perspective in each of the five chapters and, though these can be read as independent contributions, the objective is that all chapters read together, form a clear, concise, continuous unit. And so it must be said this is not a dissertation about unfinished public works in Italy; this is a dissertation about Incompiuto Siciliano as an artistic response to unfinished public works in Italy – which clearly requires an interdisciplinary analysis involving Urban Studies, Cultural Geography, Contemporary Archaeology, Critical Heritage and Visual Arts. KW - Kulturerbe KW - incompiuto siciliano KW - unfinished public works KW - modern ruins KW - incompletion KW - heritage KW - aesthetics KW - art KW - culture Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170715-32656 ER - TY - THES A1 - Meyer-Kohlstock, Daniel T1 - Prospects for Biochar in a Bio-Waste Cascade N2 - In the early 2000s the pre-Columbian, anthropologically produced black soil in the Amazon basin, „Terra Preta de Índio“, received greater scientific attention. Compared to the surrounding poor soils, this very fertile anthrosol contains significantly higher levels of microorganisms and nutrients. The reason for this was determined to be the likewise high levels of charred biomass. This stable carbon, now called biochar, has since been intensively examined as an option to improve soil and to store carbon. Although the creation of Terra Preta was most likely based on a purposeful utilization of organic residues from households and gardens, biochar plays no role in the current recycling of bio-waste. However, the implementation of biochar could lead to many improvements. Results from agricultural research suggest that not only the yield capacity of soils can be increased but also the process performance of composting and biogas plants. The latter is especially relevant since currently about 40% of all collected bio-waste in Germany is recycled in an energy-material cascade consisting of anaerobic digestion and composting. The use of biochar in this cascade could then sequentially increase biogas yields, reduce greenhouse gas emissions, and improve compost quality. To realize the aforementioned advantages, the concept of biochar has to be integrated into the existing bio-waste cascade as practically as possible. This was done by the development of a theoretical scenario that allowed the analysis of energy and material flows to evaluate biochar’s recycling performance. Furthermore, the legal and economic framework were examined to assess the feasibility of the extended cascade and to suggest possible adjustments to the frameworks. KW - Kompost KW - Biogas KW - Pflanzenkohle Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171108-36310 ER - TY - THES A1 - Msekh, Mohammed Abdulrazzak T1 - Phase Field Modeling for Fracture with Applications to Homogeneous and Heterogeneous Materials N2 - The thesis presents an implementation including different applications of a variational-based approach for gradient type standard dissipative solids. Phase field model for brittle fracture is an application of the variational-based framework for gradient type solids. This model allows the prediction of different crack topologies and states. Of significant concern is the application of theoretical and numerical formulation of the phase field modeling into the commercial finite element software Abaqus in 2D and 3D. The fully coupled incremental variational formulation of phase field method is implemented by using the UEL and UMAT subroutines of Abaqus. The phase field method considerably reduces the implementation complexity of fracture problems as it removes the need for numerical tracking of discontinuities in the displacement field that are characteristic of discrete crack methods. This is accomplished by replacing the sharp discontinuities with a scalar damage phase field representing the diffuse crack topology wherein the amount of diffusion is controlled by a regularization parameter. The nonlinear coupled system consisting of the linear momentum equation and a diffusion type equation governing the phase field evolution is solved simultaneously via a Newton- Raphson approach. Post-processing of simulation results to be used as visualization module is performed via an additional UMAT subroutine implemented in the standard Abaqus viewer. In the same context, we propose a simple yet effective algorithm to initiate and propagate cracks in 2D geometries which is independent of both particular constitutive laws and specific element technology and dimension. It consists of a localization limiter in the form of the screened Poisson equation with, optionally, local mesh refinement. A staggered scheme for standard equilibrium and screened Cauchy equations is used. The remeshing part of the algorithm consists of a sequence of mesh subdivision and element erosion steps. Element subdivision is based on edge split operations using a given constitutive quantity (either damage or void fraction). Mesh smoothing makes use of edge contraction as function of a given constitutive quantity such as the principal stress or void fraction. To assess the robustness and accuracy of this algorithm, we use both quasi-brittle benchmarks and ductile tests. Furthermore, we introduce a computational approach regarding mechanical loading in microscale on an inelastically deforming composite material. The nanocomposites material of fully exfoliated clay/epoxy is shaped to predict macroscopic elastic and fracture related material parameters based on their fine–scale features. Two different configurations of polymer nanocomposites material (PNCs) have been studied. These configurations are fully bonded PNCs and PNCs with an interphase zone formation between the matrix and the clay reinforcement. The representative volume element of PNCs specimens with different clay weight contents, different aspect ratios, and different interphase zone thicknesses are generated by adopting Python scripting. Different constitutive models are employed for the matrix, the clay platelets, and the interphase zones. The brittle fracture behavior of the epoxy matrix and the interphase zones material are modeled using the phase field approach, whereas the stiff silicate clay platelets of the composite are designated as a linear elastic material. The comprehensive study investigates the elastic and fracture behavior of PNCs composites, in addition to predict Young’s modulus, tensile strength, fracture toughness, surface energy dissipation, and cracks surface area in the composite for different material parameters, geometry, and interphase zones properties and thicknesses. T2 - Phasenfeldmodellierung für Brüche mit Anwendungen auf homogene und heterogene Materialien KW - Finite-Elemente-Methode KW - Phase field model KW - Fracture KW - Abaqus KW - Finite Element Model Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170615-32291 ER -