TY - JOUR A1 - Zhuang, Xiaoying A1 - Huang, Runqiu A1 - Liang, Chao A1 - Rabczuk, Timon T1 - A coupled thermo-hydro-mechanical model of jointed hard rock for compressed air energy storage JF - Mathematical Problems in Engineering N2 - Renewable energy resources such as wind and solar are intermittent, which causes instability when being connected to utility grid of electricity. Compressed air energy storage (CAES) provides an economic and technical viable solution to this problem by utilizing subsurface rock cavern to store the electricity generated by renewable energy in the form of compressed air. Though CAES has been used for over three decades, it is only restricted to salt rock or aquifers for air tightness reason. In this paper, the technical feasibility of utilizing hard rock for CAES is investigated by using a coupled thermo-hydro-mechanical (THM) modelling of nonisothermal gas flow. Governing equations are derived from the rules of energy balance, mass balance, and static equilibrium. Cyclic volumetric mass source and heat source models are applied to simulate the gas injection and production. Evaluation is carried out for intact rock and rock with discrete crack, respectively. In both cases, the heat and pressure losses using air mass control and supplementary air injection are compared. KW - Energiespeicherung KW - Druckluft KW - Kaverne KW - Modellierung Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170428-31726 ER - TY - CHAP A1 - Rueppel, Uwe A1 - Meißner, Udo F. A1 - Greb, Steffen T1 - A Petri Net based Method for Distributed Process Modelling in Structural Engineering N2 - The contribution introduces a method for the distributed process modelling in order to support the process orientation in Structural Engineering, i.e., the modelling, analysis and management of planning processes. The approach is based on the Petri Net theory for the modelling of planning processes and workflows in Structural Engineering. Firstly, a central and coarse process model serves as a pre-structuring system for the detailed modelling of the technical planning activities. Secondly, the involved planning participants generate distributed process models with detailed technical workflow information. Finally, these distributed process models will be combined in the central workflow net. The final net is of great importance for the process orientation in Structural Engineering, i.e., the identification, publication, analysis, optimization and finally the management of planning processes. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Petri-Netz Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1338 ER - TY - JOUR A1 - Rebolj, D. T1 - A Product Model of a Road N2 - Many errors and delays frequently appear when data is exchanged between particular tasks in the lifecycle of the road. Inter-task connections are therefore of great importance for the quality of the final product. The article describes a product model of a road wich is the kernel of an integrated information system intended to support all important stages of the road lifecycle: design, evaluation (through different analysis procedures), construction, and maintainance. Since particular tasks are often executed at different places and in different companies, the interconnections are supported by a special metafile which contains all specific data of the product model. The concept of the integrated system is object and component oriented. Additionally, existing conventional program packages are included to support some common tasks (methods). A conventional relational database system as well as an open spatial database system with the relevant GIS functionality are included to support the data structures of the model. KW - Straße KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4584 ER - TY - CHAP A1 - Olivier, A. H. T1 - An application-centred framework for distributed engineering applications N2 - The conceptual structure of an application that can support the structural analysis task in a distributed collaboratory is described in (van Rooyen and Olivier 2004). The application described there has a standalone component for executing the finite element method on a local workstation in the absence of network access. This application is comparable to current, local workstation based finite element packages. However, it differs fundamentally from standard packages since the application itself, and its objects, are adapted to support distributed execution of the analysis task. Basic aspects of an object-oriented framework for the development of applications which can be used in similar distributed collaboratories are described in this paper. An important feature of this framework is its application-centred design. This means that an application can contain any number of engineering models, where the models are formed by the collection of objects according to semantic views within the application. This is achieved through very flexible classes Application and Model, which are described in detail. The advantages of the application-centred design approach is demonstrated with reference to the design of steel structures, where the finite element analysis model, member design model and connection design model interact to provide the required functionality. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Framework Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1353 ER - TY - CHAP A1 - Raue, Erich T1 - Anwendung der mathematischen Optimierung bei der Modellbildung und Analyse des nichtlinearen Tragverhaltens von Stahlbetontragwerken N2 - In den zurückliegenden Jahren wurden an der Professur Massivbau I umfangreiche Untersuchungen zur Modellbildung und rechnerischen Erfassung des Tragverhaltens von Tragwerken und Tragwerkselementen aus Stahlbeton und Spannbeton unter Berücksichtigung von Rißbildungen und Plastizierungen durchgeführt. Diesen Untersuchungen liegt als einheitliches methodisches Konzept der mathematischen Problembeschreibung und Problemlösung die mathematische Optimierung zugrunde. Bereits anläßlich des IKM 1994 [1] hatte der Verfasser Gelegenheit, zusammenfassend über Ergebnisse bei der Anwendung der mathematischen Optimierung im Bereich der nichtlinearen Tragwerksanalyse zu berichten. Der vorliegende Beitrag, soll einen Überblick über seitdem untersuchte Problemkreise und dabei gewonnene Ergebnisse und Erfahrungen vermitteln. Bei der Anwendung der linearen und quadratischen Optimierung sind wegen der geforderten Linearität der Nebenbedingungen Vereinfachungen bei der Modellbildung des stahlbetonspezifischen Tragverhaltens unumgänglich. Besonders betroffen sind die Ansätze zur Beschreibungen des Materialverhaltens. Durch den Einsatz allgemeiner nichtlinearer mathematischer Optimierungsmethoden lässt sich eine methodisch bedingte Linearisierung des Berechnungsmodells umgehen.... KW - Tragwerk KW - Stahlbeton KW - Tragverhalten KW - Nichtlineares Phänomen KW - Modellierung KW - Optimierung Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-3717 ER - TY - CHAP A1 - Raue, Erich A1 - Timmler, Hans-Georg A1 - Schüler, H. T1 - Anwendung der mathematischen Optimierung bei der physikalisch und geometrisch nichtlinearen Analyse und Bemessung seismisch beanspruchter Tragwerke N2 - Moderne Bemessungskonzepte für seismisch beanspruchte Hochbauten, wie die Methode der Kapazitäts-bemessung, planen inelastisches Verhalten einzelner Bereiche der Konstruktion beim Entwurf bewußt ein, um so einen Teil der durch das Beben eingetragenen Energie als inelastische Formänderungsarbeit zu absorbieren. Wird bei Akzeptanz inelastischen Verhaltens eine bestimmte Belastungsintensität, die als adaptive Grenzlast oder Einspiellast bezeichnet wird, überschritten, kann es infolge zyklischer Einwirkungen zu einer unbe-grenzten Akkumulation inelastischer Deformationen kommen. Die adaptive Grenzlast stellt damit für zyklische Einwirkungen eine geeignete Kenngröße zur Bewertung der Tragwerksqualität dar, bei der neben der Sicherung des Gleichgewichts ein bestimmtes Schädigungsniveau nicht überschritten wird. Im vorliegenden Beitrag werden die Grundzüge eines Bemessungs- und Nachweiskonzeptes für seismisch beanspruchte Stahlbetontragwerke, das unter Einbeziehung der Grundprinzipe der Kapazitätsbemessung von einem einheitlichen Kriterium zur Beschreibung des Grenzzustandes der Tragfähigkeit auf der Basis der adaptive Grenzlast ausgeht, vorgestellt. Dabei ist die Abschätzung der Verformungen notwendiger Bestandteil des Nachweis- bzw. Bemessungskonzeptes. Bei Druckgliedern ist die Berücksichtigung des Einflusses der Verformungen notwendiger Bestandteil des Bemessungskonzeptes. Entsprechende Erweiterungen der Berechnungsmodelle zur Berücksichtigung des Einflusses geometrisch nichtlinearer Effekte im Sinne einer Theorie II. Ordnung werden vorgestellt. KW - Bauwerk KW - Erdbebenbelastung KW - Nichtlineares Phänomen KW - Optimierung KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4421 ER - TY - THES A1 - Semar, Olivier T1 - Anwendung der Perkolationstheorie zur Analyse des suffosiven Partikeltransportes T1 - An application of the percolation theory to analyse suffusive particle transport N2 - Die vorliegende Arbeit beschäftigt sich mit der geometrischen Suffosionsbeständigkeit von Erdstoffen. Mit dem wahrscheinlichkeitstheoretischen Ansatz der Perkolationstheorie wurde ein analytisches Verfahren gewählt, mit dem suffosive Materialtransportprozesse modelliert und quantifiziert werden können. Mit dem verwendeten Perkolationsmodell wurde eine beliebige Porenstruktur eines realen Erdstoffes im 3-Dimensionalen modelliert. Mögliche Materialtransportprozesse innerhalb der modellierten Porenstruktur wurden anschließend simuliert. Allgemein gültige Gesetzmäßigkeiten wurden hergeleitet und Grenzbedingungen formuliert. Diese sind vom Erdstoff unabhängig und beschreiben Zusammenhänge zwischen Materialtransport und Porenstruktur. Anwendbar sind diese Ergebnisse auf homogene, isotrope und selbstähnliche Erdstoffgefüge. Aussagen über konkrete Erdstoffe können über die Transformationsmethode erfolgen. Für die Verwendung der Transformationsmethode ist vorab die relevante Porenstruktur, d. h. die Porenengstellenverteilung, zu ermitteln. N2 - This thesis presents a new approach to analyze the geometrical suffusion stability of soils. With the percolation theory an analytical method is used which takes a 3D pore structure into account. This theory is a branch of the probability theory dealing with properties of random media. Characteristic parameters of the pore structure in 3D can be denoted. Possible granular structural change of arbitrary soils can be simulated and quantified. Self similarity as well as isotropic and homogeneous conditions are therefore assumed. General mathematical interrelationships and limiting conditions of granular structural change were derived. These interrelationships and limiting conditions are irrespective of the soil. They describe the relationship between potential movement of fines and the related pore structure. This requires that in advance the relevant pore structure has to be calculated. Relevant for transport and clogging of fines is the constriction size distribution of the quasi static granular structure. T3 - Schriftenreihe Geotechnik - 23 KW - Perkolationstheorie KW - Suffosion KW - Modellierung KW - Computersimulation KW - percolation theory KW - suffusion KW - modelling KW - simulation Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20101124-15252 UR - http://vg01.met.vgwort.de/na/381cd1300fab4e448c1914ae18e63f1d ER - TY - CHAP A1 - Most, Thomas A1 - Bucher, Christian T1 - Application of the "fictious crack model" to meshless crack growth simulations N2 - In this paper a meshless component is presented, which internally uses the common meshless interpolation technique >Moving Least Squares<. In contrast to usual meshless integration schemes like the cell quadrature and the nodal integration in this study integration zones with triangular geometry spanned by three nodes are used for 2D analysis. The boundary of the structure is defined by boundary nodes, which are similar to finite element nodes. By using the neighborhood relations of the integration zones an efficient search algorithm to detected the nodes in the influence of the integration points was developed. The components are directly coupled with finite elements by using a penalty method. An widely accepted model to describe the fracture behavior of concrete is the >Fictitious Crack Model< which is applied in this study, which differentiates between micro cracks and macro cracks, with and without force transmission over the crack surface, respectively. In this study the crack surface is discretized by node pairs in form of a polygon, which is part of the boundary. To apply the >Fictitious Crack Model< finite interface elements are included between the crack surface nodes. The determination of the maximum principal strain at the crack tip is done by introducing an influence area around the singularity. On a practical example it is shown that the included elements improve the model by the transmission of the surface forces during monotonic loading and by the representation of the contact forces of closed cracks during reverse loading. KW - Bruchmechanik KW - Rissbildung KW - Modellierung Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-3359 ER - TY - CHAP A1 - Hartmann, Ulrich C. T1 - Collaboration in AEC Design : Web-enabling Applications using Peer-to-Peer Office Communicator N2 - A market analysis conducted by Gartner Dataquest in August 2001 has shown the typical characteristics of the AEC design process. High volatility in membership of AEC design groups and members dispersed over several external offices is the common collaboration scenario. Membership is most times short lived, compared to the overall duration of the process. A technical solution has to take that into account by making joining and leaving a collaborative work group very easy. The modelling of roles of collaboration between group members must be based on a commonly understood principle like the publisher / subscriber model, where the individual that is responsible for the distribution of vital information is clear. Security issues and trust in the confidentiality of the system is a central concern for the acceptance of the system. Therefore, keeping the subset of data that will be published under the absolute control of the publisher is a must. This is not the case with server-based scenarios, sometimes even due to psychological reasons. A loosely bound Peer-to-Peer network offers advantages over a server-based solution, because of less administrative overhead and simple installation procedures. In a peer-to-peer environment, a publish/subscribe role model can be more easily implemented. The publish/subscribe model matches the way AEC processes are modelled in real world scenarios today, where legal proof of information exchange between external offices is of high importance. Workflow management systems for small to midsize companies of the AEC industry may adopt the peer-to-peer approach to collaboration in the future. Further investigations are being made on the research level (WINDS) by integrating the viewer and redlining application Collaborate! into a collaborative environment. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Kommunikationsmodell Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1386 ER - TY - CHAP A1 - Miles, John A1 - Joita, Liviu A1 - Burnap, Peter T1 - Collaborative Engineering: Virtual Teams in a Grid Environment Supporting Consortia in the Construction Industry N2 - In the AEC (Architecture / Engineering / Construction) industry a number of individuals and organisations collaborate and work jointly on a construction project. The resulting consortium has large pool of expertise and experience and can be defined as a Virtual Organisation (VO) formed for the duration of the project. VOs are electronically networked organisations where IT and web based communication technology play an important role in coordinating various activities of these organisations. This paper describes the design, development and implementation of a Grid enabled application called the Product Supplier Catalogue Database (PSCD) which supports collaborative working in consortia. As part of the Grid-enabling process, specialised metadata is being developed to enable PSCD to effectively utilise Grid middleware such as Globus and Java CoG toolkits. We also describe our experience whilst designing, developing and deploying the security service of the application using the Globus Security Interface (GSI). KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Projektmanagement Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1362 ER - TY - CHAP A1 - Wittwer, Christof T1 - ColSim - Eine modulare Simulationsumgebung zur Entwicklung von Regelungsalgorithmen für Embedded Systems in Energieversorgungsanlagen N2 - Am Fraunhofer ISE wurde in den letzten Jahren die Simulationsumgebung ColSim entwickelt, die sich speziell zur Untersuchung von Regelungssystemen in Gebäudeenergieversorgungssystemen eignet. Zielsetzung des Designs ist die Umsetzung des simulationsbasierten Regelungsentwurfs, der einen unmittelbaren Einsatz der Regelungsmodule auf sog. Enbedded Systems gestattet. Das Simulationswerkzeug zeichnet sich durch die modulare offene Struktur aus, die eine flexible Erweiterung ermöglicht (vgl. TRNSYS [1]). Die Implementierung erfolgte im genormten ANSI-C Code, der einen plattform- unabhänigen Einsatz gewährleistet. Entwicklungsplattform stellt derzeit ein Linux Cluster dar, als Zielplattform wurden bisher sowohl eingebettete Industrie-PCs wie auch klassische Micro- controller Boards verwendet. Die Entwurfsmethode wird anhand einer Systemregelung für eine solarthermische Anlage mit 120m2 Kollektorfläche (SolarThermie2000 Anlage) demonstriert, bei der ein vernetztes Regelungssystem mit Internet-Integration zum Einsatz kommt. Das Regelungssystem verfügt seinerseits über ein Betriebssystem (schlankes embedded linux system), das die Kommunikation nach aussen gestattet. Das Regelungssystem vefügt somit über Klima- bzw Strahlungsdaten, die für den Regelungsprozess von Bedeutung sind. Die externen Informationen können einerseits zur >Einsparung< von Sensorik genutzt werden, andererseits gestatten sie den Einsatz von prädiktiver Regelungsmethodik, um den fossilen (Nachheiz-) Energieeinsatz zu minimieren. Mit Hilfe von simulationstechnischen Systemstudien kann ein adaptives Verhalten des Regelungssystems erprobt werden, das eine selbstständige Strecken- identifikation realieren kann. Beispielsweise soll beim näher beschriebenen solarthermischen System die Totzeit bestimmt werden, die sich infolge der Verrohrung zwischen Speicher und Entladegruppe ergibt. Der Betrieb der Entlade- pumpe wird einerseits in Abhängigkeit der Verfügbarkeit des Pufferwassers erfolgen, andererseits in Abhängigkeit des erwarteten Zapfvolumens durch den Verbraucher. Die vernetzten Regelungssysteme, die auf Basis der Simulationsmodelle ent- wickelt werden, sollen künftig die gesamte Energieflußanalyse des Gebäudes realisieren, wobei eine transparente Darstellung des Systemverhaltens auf Basis einer Internet Visualisierung erfolgt. Der Betreiber und Nutzer wird unmittel- bar durch die Online Dienste (SMS,Email,Fax) über das (fehlerhafte) Anlagen- verhalten informiert. Gerade die sensitiven regenerativen Systeme neigen durch ihre Komplexität zu Störungen, die oftmals nicht erkannt werden, weil die konventionellen Teilsysteme (z.B. Ergasbrenner) den Ausfall in der Regel >kompensieren<. KW - Gebäude KW - Energieversorgung KW - Regelungssystem KW - Modellierung Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-3803 ER - TY - CHAP A1 - Baranski, Jacek A1 - Boron, Jacek T1 - Computer Modeling of the Joints for WGP Construction Systems N2 - Poland is not situated in any seismic region of the earth, however there are still areas were underground mining is being conducted. In these areas, so-called 'paraseismic tremors', are very frequent phenomena. In the situation when a building examination is realized in order to define its safety, it is necessary to make a complete analysis, in which an influence of tremors should be included. To decide if a building is able to carry out any dynamic loads or not, it is necessary to compute its dynamic characteristics, i.e. natural frequencies. It is not possible using any standard techniques. After diagnosis a building in situ by an expert, computer techniques together with specialized software for dynamic, static, and strength analyses become a suitable tool. In this paper a special attention was paid to a typical twelve-store WGP (Wroclaw Great Plate) prefabricated building, concerning special type of joints. During dynamic actions these joints have a decisive influence on building's behavior. Paraseismic tremors are especially dangerous for these buildings and can be the reason of pre-failure states. It can be difficult and very expensive to prepare laboratory investigations of the part of a building or of a separate joint; therefore the computer modeling suitable to investigate behavior of such elements and whole buildings under different kinds of loads was used. KW - Gebäude KW - Modellierung Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2935 ER - TY - THES A1 - Hauschild, Thomas T1 - Computer Supported Cooperative Work-Applikationen in der Bauwerksplanung auf Basis einer integrierten Bauwerksmodellverwaltung T1 - Computer Supported Cooperative Work Applications for the Design of Buildings based on an integrated Building Model Management N2 - Gegenstand der vorliegenden Arbeit ist die Konzeption und prototypische Umsetzung von Techniken des Computer Supported Cooperative Work (CSCW) im Rahmen einer integrierten objektorientierten und dynamischen Bauwerksmodellverwaltung zur Unterstützung der Bauwerksplanung. Die Planung von Bauwerken ist durch einen hohen Grad an Arbeitsteiligkeit, aber auch durch eine schwache Strukturierung der ablaufenden Prozesse gekennzeichnet. Besonders durch den Unikatcharakter des Planungsgegenstands \'Bauwerk\' ergeben sich signifikante Unterschiede zum Entwurf anderer, durch Serienfertigung produzierter Industriegüter. Zunehmend wird die Planung von Bauwerken in Virtual Enterprises ausgeführt, die sich durch eine dynamische Organisationsstruktur, geographische Verteilung der Partner, schwer normierbare Informationsflüsse und eine häufig stark heterogene informationstechnische Infrastruktur auszeichnen. Zur rechnerinternen Repräsent! ation des Planungsgegenstands haben sich objektorientierte Bauwerksmodelle bewährt. Aufgrund der Veränderlichkeit der Bauwerke und deren rechnerinterner Repräsentation im Laufe des Bauwerkslebenszyklus ist eine dynamische Anpassung der Modelle unumgänglich. Derartige in Form von Taxonomien dargestellte dynamische Bauwerksmodellstrukturen können gemeinsam mit den in Instanzform vorliegenden konkreten Projektinformationen in entsprechenden Modellverwaltungssystemen (MVS) gehandhabt werden. Dabei wird aufgrund der Spezialisierung und Arbeitsteilung im Planungsprozess von einer inhaltlich verknüpften Partialmodellstruktur, die räumlich verteilt sein kann, ausgegangen. Die vorgeschlagenen Methoden zur Koordinierung der Teamarbeit in der Bauwerksplanung beruhen auf der Nutzung von CSCW–Techniken für \'Gemeinsame Informationsräume\' und \'Workgroup Computing\', die im Kontext der als Integrationsbasis fungierenden Modellverwaltungssysteme umgesetzt werden. Dazu werden die zur d! ynamischen Bauwerksmodellierung erforderlichen Metaebenenfunk! tionalitäten sowie Ansätze zur Implementierung von Modellverwaltungskernen systematisiert. Ebenso werden notwendige Basistechniken für die Realisierung von MVS untersucht und eine Architektur zur rollenspezifischen Präsentation dynamischer Modellinhalte vorgestellt. Da klassische Schichtenmodelle nicht auf die Verhältnisse in Virtual Enterprises angewendet werden können, wird eine physische Systemarchitektur mit einem zentralen Projektserver, Domänenservern und Domänenclients vorgestellt. Ebenso werden Techniken zur Sicherung des autorisierten Zugriffs sowie des Dokumentencharakters beschrieben. Zur Unterstützung der asynchronen Phasen der Kooperation wird der gemeinsame Informationsraum durch Mappingtechniken zur Propagation und Notifikation von Änderungsdaten bezüglich relevanter Modellinformationen ergänzt. Zur Unterstützung synchroner Phasen werden Techniken zur Schaffung eines gemeinsamen Kontexts durch relaxierte WYSIWIS–Präsentationen auf Basis der Modellinformationen! verbunden mit Telepresence–Techniken vorgestellt. Weiterhin werden Methoden zur Sicherung der Group–Awareness für alle Kooperationsphasen betrachtet. N2 - The thesis covers the conceptual design and the prototypical realisation of Computer Supported Cooperative Work (CSCW)– techniques within the scope of an integrated, object-oriented, dynamic model management system for the support of building planning activities. The planning of buildings is characterised by a high degree of collaboration but by a weak structuring of the processes, too. Significant differences between the design of buildings and industrial goods produced by series production are implied by the uniqueness of a building. Increasingly, the planning of buildings is accomplished by Virtual Enterprises. These are characterised by a dynamic organisation structure, geographic dispersion of the involved planning experts, information flows, which are hard to standardise, and a frequently very heterogeneous information-technology infrastructure. Object oriented building models have proven to be a suitable base for! the binary representation of planning subject information. Due to the changeability of both building structures and their binary representation during the building life cycle, a dynamical adaptation of the models is indispensable. Dynamic building models, which are represented by taxonomic information, can be handled together with actual project information, which is stored in taxonomy instances within an appropriate model management system. Due to the specialisation and the division of labour in the planning process, a semantic linked but spatial distributed partial model structure is applied. The recommended methods for the coordination of teamwork in the planning process are based on the application of CSCW-techniques for \'Shared Information Spaces\' and \'Workgroup Computing\' in the context of model management systems acting as an foundation for planning information integration. The required meta level functionalities for dynamic building modelling and appropriate! implementation approaches for modelling kernels are systemat! ised. The necessary base techniques for the realisation of model management systems are explored. An architecture for the role specific presentation of dynamic model content is introduced, too. Due to the inadequacy of conventional multi-tier models for an application in Virtual Enterprises, an appropriate physical system architecture with a central project server, domain servers and domain clients is introduced. The thesis covers techniques, which ensure the authorised access to information and the authenticity of planning documents, too. For an adequate support of the asynchronous phases of collaboration, the Shared Information Space is supplied with mapping mechanisms for the propagation and user notification of changes in the relevant planning information. Synchronous collaboration can be performed by means of relaxed WYSIWIS-presentations connected with telepresence mechanisms in order to create a shared context for the planners. Furthermore, methods for the provis! ion of group-awareness for all co-operation phases are treated. KW - Computer Supported Cooperative Work KW - Groupware KW - Bauwerk KW - Modellierung KW - Virtuelles Unternehmen KW - Verteiltes System KW - Domänenmodelle KW - Kooperatives Arbeiten KW - CSCW KW - Dynamische Modellverwaltungssysteme KW - Dynamische Schemaevolution KW - Building Modelling KW - Domain Models KW - Co-operative Work KW - Dynamic Model Management Systems KW - Dynamic Schema Evolution Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20040311-672 ER - TY - JOUR A1 - Gürlebeck, Klaus A1 - Legatiuk, Dmitrii A1 - Nilsson, Henrik A1 - Smarsly, Kay T1 - Conceptual modelling: Towards detecting modelling errors in engineering applications JF - Mathematical Methods in Applied Sciences N2 - Rapid advancements of modern technologies put high demands on mathematical modelling of engineering systems. Typically, systems are no longer “simple” objects, but rather coupled systems involving multiphysics phenomena, the modelling of which involves coupling of models that describe different phenomena. After constructing a mathematical model, it is essential to analyse the correctness of the coupled models and to detect modelling errors compromising the final modelling result. Broadly, there are two classes of modelling errors: (a) errors related to abstract modelling, eg, conceptual errors concerning the coherence of a model as a whole and (b) errors related to concrete modelling or instance modelling, eg, questions of approximation quality and implementation. Instance modelling errors, on the one hand, are relatively well understood. Abstract modelling errors, on the other, are not appropriately addressed by modern modelling methodologies. The aim of this paper is to initiate a discussion on abstract approaches and their usability for mathematical modelling of engineering systems with the goal of making it possible to catch conceptual modelling errors early and automatically by computer assistant tools. To that end, we argue that it is necessary to identify and employ suitable mathematical abstractions to capture an accurate conceptual description of the process of modelling engineering systems. KW - Angewandte Mathematik KW - Angewandte Informatik KW - Ingenieurwissenschaften KW - Modellierung KW - engineering KW - abstraction KW - modelling KW - formal approaches KW - type theory Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20200110-40614 UR - https://onlinelibrary.wiley.com/doi/abs/10.1002/mma.5934 SP - 1 EP - 10 ER - TY - JOUR A1 - Legatiuk, Dmitrii A1 - Weisz-Patrault, Daniel T1 - Coupling of Complex Function Theory and Finite Element Method for Crack Propagation Through Energetic Formulation: Conformal Mapping Approach and Reduction to a Riemann–Hilbert Problem JF - Computational Methods and Function Theory N2 - In this paper we present a theoretical background for a coupled analytical–numerical approach to model a crack propagation process in two-dimensional bounded domains. The goal of the coupled analytical–numerical approach is to obtain the correct solution behaviour near the crack tip by help of the analytical solution constructed by using tools of complex function theory and couple it continuously with the finite element solution in the region far from the singularity. In this way, crack propagation could be modelled without using remeshing. Possible directions of crack growth can be calculated through the minimization of the total energy composed of the potential energy and the dissipated energy based on the energy release rate. Within this setting, an analytical solution of a mixed boundary value problem based on complex analysis and conformal mapping techniques is presented in a circular region containing an arbitrary crack path. More precisely, the linear elastic problem is transformed into a Riemann–Hilbert problem in the unit disk for holomorphic functions. Utilising advantages of the analytical solution in the region near the crack tip, the total energy could be evaluated within short computation times for various crack kink angles and lengths leading to a potentially efficient way of computing the minimization procedure. To this end, the paper presents a general strategy of the new coupled approach for crack propagation modelling. Additionally, we also discuss obstacles in the way of practical realisation of this strategy. KW - Angewandte Mathematik KW - Finite-Elemente-Methode KW - Rissausbreitung KW - Modellierung KW - Bruchmechanik KW - fracture mechanics KW - crack propagation KW - coupling KW - energetic approach Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210805-44763 UR - https://link.springer.com/article/10.1007/s40315-021-00403-7 VL - 2021 SP - 1 EP - 23 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Petzold, Frank A1 - Wender, Katrin A1 - Donath, Dirk A1 - Weferling, Ulrich T1 - Das Bauwerk als Informationscontainer in den frühen Phasen der Bauaufnahme - Ausgangspunkt für die Projektentwicklung und Entwurfsformulierung N2 - Die digitale Unterstützung der Planungsprozesse ist ein aktueller Forschungs- und Arbeitsschwerpunkt der Professur Informatik in der Architektur (InfAR) und der Juniorprofessur Architekturinformatik der Fakultät Architektur an der Bauhaus-Universität Weimar. Verankert in dem DFG Sonderforschungsbereich 524 >Werkzeuge und Konstruktionen für die Revitalisierung von Bauwerken< entstehen Konzepte und Prototypen für eine fachlich orientierte Planungsunterstützung. In dem Beitrag wird ein Konzept und prototypische Realisierung für die durchgängige Unterstützung des gesamten Bauaufnahmeprozesses für Altbausubstanz vorgestellt und diskutiert. Der Fokus liegt auf der frühe Phase in der Bauaufnahme als ein Baustein in einer gesamtheitlichen IT-gestützen Planungsumgebung eingegangen. Durch gezielte Aufnahme planungsrelevanter Parameter und Auswertung hinsichtlich Wirtschaftlichkeit und Wiederverwendbarkeit bzw. der Variantenüberprüfung von Nutungskonzepten, werden gerade in dieser Phase wesentliche Entscheidungen für eine kostengünstige Planung getroffen werden. In der Veröffentlichung wird der Fokus auf folgende Punkte gesetzt: - Strukturierung und Aufnahme der Informationen während der Erstbegehung - Skizzenhafte Abbildung als Basis für die Formulierung erster Entwurfsintensionen/ Variantenuntersuchungen - Navigations- und Informationsumgebung - gezielte Auswertungsmöglichkeiten (bspw. Wirtschaftlichkeitsberechnung, Wiederverwendung von Bauteilen, Kalkulation von Abrissmengen) KW - Gebäude KW - Bauaufnahme KW - Datenerfassung KW - Modellierung Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-3479 ER - TY - CHAP A1 - Laabs, Andreas A1 - Pahl, Peter Jan T1 - Das Beobachterkonzept zum Erhalt der Konsistenz in Datenmodellen N2 - Die Aufgaben des Bauingenieurwesens sind dadurch geprägt, daß sowohl die Planung als auch die Ausführung von Bauwerken häufigen Änderungen unterliegen. Beschreibt man das Verhalten der Bauwerke und den Bauprozeß im Computer mit Modellen, so ändern sich Umfang und Struktur der Modelle als Folge der Änderung in Planung und Ausführung. Diesen Vorgang nennt man Dynamisierung des Modells. Die Dynamisierung führt zu Veränderungen und Inkonsistenzen in den Modellen der Anwendungen. Die Aktualisierung und Abstimmung von Beziehungen innerhalb eines Modells sowie die Sicherung der Konsistenz der Modelle untereinander sind daher von zentraler Bedeutung für die Lösung von Bauingenieuraufgaben. Seit den letzten 10 Jahren wird die objektorientierte Methode in der Modellierung für Anwendungen im Bauingenieurwesen intensiv entwickelt und eingesetzt. Es hat sich gezeigt, daß die Anwendung dieser Methode in wichtigen Bereichen der Modellierung zu Verbesserungen führt. Gleichzeitig hat sich aber auch herausgestellt, daß die für das Bauingenieurwesen wichtigen Aspekte der Aktualisierung und der Konsistenz nicht zweckmäßig beschreibbar sind. In diesem Beitrag wird eine einfache Modelliermethode in ihrem Konzept und ihrer Realisierung gezeigt, mit der sich die Aktualisierung von Objekten und Modellen sowie die Sicherstellung der Konsistenz in Systemen des Bauingenieurwesens bearbeiten lassen. KW - Bauwerk KW - Objektmodell KW - Datenmodell KW - Bauausführung KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4310 ER - TY - THES A1 - Bubner, André T1 - Datenmodelle zur Bearbeitung von Ingenieuraufgaben am Beispiel von Wohnhäusern in Stahlbauweise T1 - Data Models for Processing of Engineering Tasks at the Example of Residential Buildings in Steel Construction Method N2 - Modelle bilden die Grundlage der Planung. Sie repräsentieren die zur Bearbeitung erforderlichen Eigenschaften eines Bauwerks in einer an die spezifische Aufgabe angepassten Form. Zwischen den verschiedenen zur Abbildung des Bauwerks eingesetzten Modellen bestehen fachliche Zusammenhänge bezüglich der darin abgebildeten Aspekte. Diese Abhängigkeiten werden in der praktischen Planungsbearbeitung gegenwärtig auf Grundlage von Erfahrungswerten, normativen Vorgaben und vereinfachenden Annahmen berücksichtigt. Die detailliertere Modellierung von Bauwerkseigenschaften führt zu einer engeren Verzahnung der verschiedenen Modelle. Um eine fachliche Inselbildung zu vermeiden, ist eine entsprechend angepasste Abbildung der zwischen den einzelnen Modellen bestehenden Beziehungen erforderlich. Mit den steigenden Ansprüchen an eine Bearbeitung von Ingenieuraufgaben gewinnt eine über den Zweck der Bereitstellung ausgewählter Informationen zum Bauwerk und der Unterstützung eines Datenaustauschs zwischen verschiedenen Fachplanern hinausgehende datentechnische Abbildung an Bedeutung. Dies setzt eine Diskussion der Anforderungen an eine solche Beschreibung aus fachlicher Sicht voraus. Die Untersuchung der fachlichen Anforderungen wird am Beispiel von Wohnhäusern in Stahlbauweise geführt. N2 - Models form the basis of the planning. They represent the characteristics necessary for the processing of a building in a form suited to the specific task. Between the different models, which are used for the representation of the building, there exist engineer-technical interrelations with regard to the illustrated aspects. At present these dependences are taken into consideration in the practical planning on basis of empirical values, normative guidelines and simplifying assumptions. The more detailed modelling of the building characteristics leads to a more defined linkage of the different models. To avoid an engineering island formation, there is an accordingly adapted representation of the relations existing between the single models necessary. With the rising demands on the processing of engineering tasks a data-technical representation wins in importance which realises more than a supply of selected information about the building and the support of a data exchange between different planners. This requires a discussion of the requirements for such a description from an engineer-technical view. The investigation of these technical requirements is carried out by the example of residential buildings in steel construction method. KW - Modellierung KW - Stahlbau KW - Wohnungsbau KW - Datenmodell KW - Modellbildung KW - Wohnhäuser in Stahlbauweise KW - fachliche Integration KW - Bearbeitung von Ingenieuraufgaben KW - modelling KW - residential buildings KW - engineer-technical integration KW - processing of engineering tasks Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20070423-8580 ER - TY - CHAP A1 - Lähr, André A1 - Bletzinger, Kai-Uwe T1 - Design of an Analysis Environment for Planning Decision Support N2 - In this contribution, the design of an analysis environment is presented, that supports an analyst to come to a decision within a gradual collaborative planning process. An analyst represents a project manager, planner or any other person, involved in the planning process. Today, planning processes are managed by several geographically distributed planners and project managers. Thus, complexity of such a process rises even more. Prediction of consequences of many planning decisions is not possible, in particular since assessment of a planning advance is not trivial. There have to be considered several viewpoints, that depend on individual perceptions. In the following, methods are presented to realize planning decision support. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Schlussfolgern Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1370 ER - TY - CHAP A1 - Yahiaoui, Azzedine A1 - Hensen, Jan A1 - Soethout, Luc T1 - Developing CORBA-based distributed control and building performance environments by run-time coupling N2 - Communication software and distributed applications for control and building performance simulation software must be reliable, efficient, flexible, and reusable. This paper reports on progress of a project, which aims to achieve better integrated building and systems control modeling in building performance simulation by run-time coupling of distributed computer programs. These requirements motivate the use of the Common Object Request Broker Architecture (CORBA), which offers sufficient advantage than communication within simple abstraction. However, set up highly available applications with CORBA is hard. Neither control modeling software nor building performance environments have simple interface with CORBA objects. Therefore, this paper describes an architectural solution to distributed control and building performance software tools with CORBA objects. Then, it explains how much the developement of CORBA based distributed building control simulation applications is difficult. The paper finishes by giving some recommendations. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - CORBA Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1347 ER -