TY - JOUR A1 - Wiedemann, A. T1 - Digital Architectural Photogrammetry for Building Registration N2 - For many purposes geometric information about existing buildings is necessary, e.g. planing of conservation or reconstruction. Architectural photogrammetry is a technique to acquire 3D geometric data of buildings for a CAD model from images. In this paper the state of the art in architectural photogrammetry and some developments towards automation are described. The photogrammetric process consists of image acquisition, orientation and restitution. Special attention is put on digital methods, from digital image acquisition to restitution methods, supported by digital image processing. There are a few field of development towards automation, e.g. feature extraction, extraction of edges and lines and the detection of corresponding points. The acquired data may be used in a CAD environment or for visualization in Virtual Reality Models, using digital orthoimages for texture mapping. KW - Bauwerk KW - Projektdokumentation KW - Photogrammetrie Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4892 ER - TY - JOUR A1 - Kicinger, Rafal A1 - Arciszewski, Tomasz A1 - De Jong, Kenneth T1 - Distributed Evolutionary Design: Island-Model-based Optimization of Steel Skeleton Structures in Tall Buildings N2 - This paper presents results of a study on distributed, or parallel, evolutionary computation in the topological design of steel structural systems in tall buildings. It describes results of extensive experimental research on various parallel evolutionary architectures applied to a complex structural design problem. The experiments were conducted using Inventor 2003, a networkbased evolutionary design support tool developed at George Mason University. First, a general introduction to evolutionary computation is provided with an emphasis on recent developments in parallel evolutionary architectures. Next, a discussion of conceptual design of steel structural systems in tall buildings is presented. Further, Inventor 2003 is briefly introduced as well as its design representation and evolutionary computation characteristics. Next, the results obtained from systematic design experiments conducted with Inventor 2003 are discussed. The objective of these experiments was to qualitatively and quantitatively investigate evolution of steel structural systems in tall buildings during a distributed evolutionary design process as well as to compare efficiency and effectiveness of various parallel evolutionary architectures with the traditional evolutionary design approaches. Two connectivity topologies (ring topology and fully-connected topology) have been investigated for four populations of structural designs evolving in parallel and using various migration strategies. Also, results of the initial sensitivity studies are reported in which two ways of initializing distributed evolutionary design processes were investigated, using either arbitrarily selected designs as initial parents or randomly generated ones. Finally, initial research conclusions are presented. KW - Mehragentensystem KW - Lernendes System KW - Stahlbau KW - Skelettbau KW - Optimierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2195 ER - TY - JOUR A1 - Semenov, Vitaly A1 - Bazhan, Andrew A1 - Morozov, Sergey T1 - Distributed STEP-Compliant Platform for Multimodal Collaboration in Architecture, Engineering, and Construction N2 - This paper presents an innovative software platform OpenSTEP intended to build advanced distributed integrated systems and to conduct multidisciplinary collaborative projects in both academy and industry. The paper discusses an open system architecture, methodology, component library and CASE toolkit enabling the developers to build a wide range of interoperable applications and systems compliant with STEP and, particularly, with IFC becoming the increasingly important standard for information integration in architecture, engineering and construction. KW - Framework KW - API KW - STEP KW - Verteiltes System Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2616 ER - TY - JOUR A1 - Lizounov, P. P. T1 - Dynamics of solid and deformable Bodies Systems at complex Movements N2 - Analytical models, describing oscillations of systems of interconnected solid and deformable bodies,making a complex movement in fields of inertia forces and gravitation forces, are resulted. Method of numerical investigation of dynamics of the specified systems, based on sharing of parameter prolongation method, Newton-Kantorovich algorithm, Flocke and Liapunov hteories, is developed. On the basis of constructed analytical models and numerical techniques a new, practically important problems of dynamics of systems, consisting of solid bodies, flexible rods, membranes and soft shells, which make a complex movement in fields of forces of inertia and gravity are solved. The received results are used during designing of responsible elements of structures, making a complex movement, which find application in construction and mechanical engineering. KW - Festkörpermechanik KW - Dynamische Belastung KW - Numerisches Verfahren Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5410 ER - TY - JOUR A1 - Kwak, Hyo-Gyoung A1 - Kim, Jin-Kook T1 - Efficient Shoring System in RC Frame Structures N2 - In this paper, systematic analyses for the shoring systems installed to support the applied loads during construction are performed on the basis of the numerical approach. On the basis of a rigorous time-dependent analysis, structural behaviors of reinforced concrete (RC) frame structures according to the changes in design variables such as the types of shoring systems, shore stiffness and shore spacing are analyzed and discussed. The time-dependent deformations of concrete such as creep and shrinkage and construction sequences of frame structures are also taken into account to minimize the structural instability and to reach to an improved design of shoring system because these effects may increase the axial forces delivered to the shores. In advance, the influence of the column shortening effect, generally mentioned in a tall building structure, is analyzed. From many parametric studies, it has been finally concluded that the most effective shoring system in RC frame structures is 2S1R (two shores and one reshore) regardless of the changes in design variables. KW - Finite-Elemente-Methode KW - Physikalisches Verfahren KW - Skelettbau KW - Construction Sequence KW - Shoring System KW - Shore Stiffness KW - Shore Spacing Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2511 ER - TY - JOUR A1 - Caetano, A. M. T1 - Eigenvalue Distribution for the Stokes Operator N2 - The aim of this talk is to show that the methods used by Métivier and Lapidus to study the eigenvalue distribution of elliptic operators (e.g., of the Dirichlet Laplacian) can be adapted to the study of the similar problem for the Stokes operator. In this way we get asymptotic formulae for the eigenvalues of the latter operator even in the case when the underlying domain has an extremely irregular (fractal) boundary. In the case the boundary is not that irregular (e.g., when it is Lipschitz) the estimates we obtain are much better than the ones we can find in the current literature. KW - Stokes-Problem KW - Eigenwert Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5005 ER - TY - JOUR A1 - Sellerhoff, F. A1 - Milbradt, Peter A1 - Lippert, C. T1 - Ein dimensionsunabhängiges topologisches Modell auf der Basis von Simplexen N2 - Die geometrische Modellierung hat in den Ingenieurwissenschaften eine große Bedeutung erlangt. Die Visualisierung von zwei- oder dreidimensionalen Problemstellungen ist aus heutigen Anwendungen nicht mehr wegzudenken. Zunehmend rücken Aufgabenstellungen aus dem Bereich der geometrischen Modellierung in den Vordergrund, die über die etablierten Dimensionen 1-3 hinausgehen und die nicht mehr rein geometrischer Natur sind. Hierzu zählen Aufgabenstellungen aus den Bereichen numerische Simulation, Parameteridentifikation und Strukturanalyse. Auf diese nicht-geometrischen Aufgabenstellungen sollen geometrische Verfahren, wie z.B. Triangulation, konvexe Hülle, geometrischer Schnitt und Interpolation angewendet werden. Hierzu werden diese Algorithmen, die alle auf der klassischen Geometrie des euklidischen Raumes beruhen, auf ihre Übertragbarkeit hin analysiert und überarbeitet. Am Beispiel einer Parameteridentifikation wird eine systematische Vorgehensweise vorgestellt, die es ermöglicht, trotz weniger Versuchsrechnungen den Bereich der in Frage kommenden Parameter umfassend zu beschreiben. Dies ermöglicht ein besseres Verständnis der Zusammenhänge der Parameter untereinander. Häufig existieren mehr als eine Parameterkombination, so daß diese eine Isolinie formen, die ihrerseits unendlich viele Lösungen des gestellten Problemes im Untersuchungsgebiet beschreibt. KW - Parameteridentifikation KW - Strukturanalyse KW - Visualisierung KW - Mehrdimensionalität Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4616 ER - TY - JOUR A1 - Fischer, A. A1 - Steinhage, V. T1 - Ein modellbasiertes Konzept zur städteplanerischen Kartierung durch digitale Bildanalyse N2 - There is an increasing need for 3D building extraction from aerial images for various applications such astown planning, environmental- and property-related studies. Aerial images usually reveal on one hand a certain amount of information not relevant for the given task of building extraction like vegetation, cars etc. On the other hand there is a loss of relevant information due to occlusions, low contrasts or disadvantageous perspectives. Therefore a promising concept for automated building reconstruction must incorporate a suffciantly complete model of the objects of interest. We propose a model-based approach to 3D building extraction from aerial images which reveals a tight coupling between a generic 3D object model and an explicit 2D image model. The generic object model employes domain specific volumetric primitives (i. e. building part models) and combination schemes. To cover the gap between 3D object models and 2D image data the image model is employed to predict the projective building appearences in aerial images. We present a strategy for a model-based building extraction based on the recognition-by-components principle and show first experimental results derived from international test sets KW - Stadtplanung KW - Kartierung KW - Bildanalyse KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4870 ER - TY - JOUR A1 - Kämmerer, Lutz A1 - Hempel, Lorenz T1 - Eine Heuristik zur Lösung von Stapelproblemen N2 - Bei der Betrachtung von Stapelproblemen ergibt sich unter anderem folgendes Problem: Ein gegebener Stapel - bestehend aus den Elementen v i der Menge V - soll an anderer Stelle in einer vorgeschriebenen, veränderten Struktur wieder aufgebaut werden. Dazu stehen Hilfsstapelplätze zur Verfügung. Die Optimierung dieses Problems hinsichtlich der Anzahl der benötigten Hilfsstapelplätze ist NP-vollständig. Es werden Erfahrungen mit einem Branch-and-Bound Algorithmus zur Lösung des Problems vorgestellt sowie ein heuristischer Algorithmus diskutiert KW - Stapelproblem KW - Heuristik Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5207 ER - TY - JOUR A1 - Abdalla, Jamal T1 - Elements of an Agent-based Mediative Communication Protocol for Design Objects N2 - Integrated structural engineering system usually consists of large number of design objects that may be distributed across different platforms. These design objects need to communicate data and information among each other. For efficient communication among design objects a common communication protocol need to be defined. This paper presents the elements of a communication protocol that uses a mediator agent to facilitate communication among design objects. This protocol is termed the Mediative Communication Protocol (MCP). The protocol uses certain design communication performatives and the semantics of an Agent Communication language (ACL) mainly the Knowledge and Query Manipulation Language (KQML) to implement its steps. Details of a Mediator Agent, that will facilitate the communication among design objects, is presented. The Unified Modeling Language (UML) is used to present the Meditative protocol and show how the mediator agent can be use to execute the steps of the meditative communication protocol. An example from structural engineering application is presented to demonstrate and validate the protocol. It is concluded that the meditative protocol is a viable protocol to facilitate object-to-object communication and also has potential to facilitate communication among the different project participants at the higher level of integrated structural engineering systems. KW - Mehragentensystem KW - Lernendes System KW - Kommunikationsprotokoll Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2207 ER - TY - JOUR A1 - Staub-French, Sheryl T1 - Feature-based Product Modeling for Building Construction N2 - Current building product models explicitly represent components, attributes of components, and relationships between components. These designer-focused product models, however, do not represent many of the design conditions that are important for construction, such as component similarity, uniformity, and penetrations. Current design and construction tools offer limited support for detecting these construction-specific design conditions. This paper describes the ontology we developed using the manufacturing concept of features to represent the design conditions that are important for construction. The feature ontology provides the blueprint for the additions and changes needed to transform a standard product model into a constructionspecific product model. The ontology formalizes three classes of features, defines the attributes and functions of each feature type, and represents the relationships between features explicitly. The descriptive semantics of the ontology allows practitioners to represent their varied preferences for naming features, specifying features that result from component intersections and the similarity of components, and grouping features that affect a specific construction domain. A software prototype that implements the ontology enables practitioners to transform designer-focused product models into feature-based product models that represent the construction perspective. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Baukonstruktion KW - Modellierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2331 ER - TY - JOUR A1 - Milbradt, Peter A1 - Schierbaum, Jochen A1 - Schwöppe, Axel T1 - Finite Cell-Elements of Higher Order N2 - The method of the finite elements is an adaptable numerical procedure for interpolation as well as for the numerical approximation of solutions of partial differential equations. The basis of these procedure is the formulation of suitable finite elements and element decompositions of the solution space. Classical finite elements are based on triangles or quadrangles in the two-dimensional space and tetrahedron or hexahedron in the threedimensional space. The use of arbitrary-dimensional convex and non-convex polyhedrons as the geometrical basis of finite elements increases the flexibility of generating finite element decompositions substantially and is sometimes the only way to get a clear decomposition... KW - Finite-Elemente-Methode KW - Physikalisches Verfahren Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2524 ER - TY - JOUR A1 - Wehner, R. A1 - Steinmann, Frank A1 - Hübler, Reinhard T1 - FLEXOB - Entwicklungstool für dynamische, modellbasierte CAD-Systeme N2 - Objektorientierte Modellierungstechniken werden gegenwärtig vor allem Entwicklern von CAD-Systemen angeboten. Sie erzeugen über die Schritte OO-Modellanalyse und OO-Softwaredesign OO-Programme, die mit ihrer Compilation das durch den Softwareingenieur gefundene Modell festschreiben. Generell, aber insbesondere im Bauwerksdesign, ist dieses Vorgehen unbefriedigend, da hier eine Normung von Modellen nicht gelingt, der Entwurfsprozeß vergleichsweise lang ist und eine Kooperation von Ingenieurgewerken mit verschiedenen Modelldomänen die Regel sind. Darüber hinaus weisen die Modelle in frühen Phasen ein hohes Maß an Unschärfe und Abstraktion auf. CAD-Tools, die diese Phasen unterstützen, benötigen deshalb: statt eines genormten Produktmodells ein einheitliches, kognitiv begründetes Modellstrukturierungsparadigma, für das mit der Objektorientierung eine mögliche Ausprägung gegeben ist, ein explizites, verfügbares Domänenmodell zur fortwährenden Interpretation von Bauwerksmodellen, deskriptive Elemente, die die Interpretation von Objekten und Attributen erleichtern, ein Konzept zur Behandlung von Unschärfe und Abstraktion. Hieraus ergeben sich für die Entwicklung von CAD-Systemen folgende Forderungen : Explizite Verfügbarkeit von Klassenobjekten und deren Erzeugung und Veränderung zur Laufzeit, Vererbung auf Klassen- und Instanzniveau, Erweiterte Attributkonzepte (Facetten), Unterstützung der Aggregation als einer wesentlichen Modellstrukturierungsrelation, Verfügbarkeit von OO-Schnittstellen zum Aufbau von CAD-Systemen aus Tools einerseits, sowie zur Trennung von Modellverwaltung und Modellrepräsentation andererseits. Als ein herausragendes Merkmal des Objektorientierten Paradigmas wird die Anwendungsnähe genannt, da Erscheinungen der behandelten Domäne sich analog in Modellen und Programmen wiederfinden (sollen). Unter der Grundannahme, daß dieses Paradigma auch durch den Anwender zur Erstellung seiner Modellwelten verwendet wird, will FLEXOB eine homogene Umgebung schaffen, die die Modellwelt des Softwareingenieurs zu Analysezwecken dem Anwender zur Verfügung stellt und die die Erweiterung dieser Modellwelt auf deskriptivem Niveau ermöglicht. Das Tool FLEXOB und einige wesentliche Implementationsdetails werden im Beitrag vorgestellt. Es handelt sich bei diesem Tools um eine C++ Klassenbibliothek, die entweder als Objektmodul oder als Windows-DLL verwendet werden kann. Aspekte des Nutzungsregimes solch flexibler Modellverwaltungen werden im Beitrag ebenfalls angespochen. KW - CAD KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4571 ER - TY - JOUR A1 - Perepelitsa, V. A. A1 - Pinchuk, V. P. A1 - Sergeeva, L. N. A1 - Pozdnjakova, A. J. T1 - Fractal Graphs and their Properties N2 - The idea of representing urban structure and various communication systems (water and energy supply, telephone and cable TV networks) as fractal objects is not absolutely new. However, known works, devoted to this problem use models and approaches from fractal physics. For example, to simulate urban growth Diffusion Limited Aggregation (DLA) model and Dielectric Breakdown (DB) model are used. This study introduces a different approach. Net structure of communication system is described by a graph of special type called regular G(l,r,n)-graph. Authors provide description of such graph, develop iterative process for its generation and prove its self-similarity, i.e. that every regular graph is a pre-fractal. After the infinite number of steps this process generates a fractal. The devised algorithm for generation and grathical representation of regular G(l,r,n)-graphs with different values of l,r and n has been programmed to receive computer simulations. For optimal graphic presentation of pre-fractals the Optimal Space Ordering method was suggested. It is based on the minimization of the >graph energy< value about vertices' coordinates. The effective procedure for optimization was developed that takes into account specific properties of graph energy as objective function For the fractal graph introduced the Hausdorff-Besikovich and similarity dimensions were calculated. It has been shown that >graph energy< is directly related to the graph's fractal properties. For G(3,3,n) and G(4,4,n) graphs fractal dimensions calculated by different methods are the same (D=1,5 and D=2 respectively), while topological dimension of both graphs is 1. KW - Versorgungsnetz KW - Fraktal KW - Graphentheorie Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5166 ER - TY - JOUR A1 - Weise, Matthias A1 - Katranuschkov, Peter A1 - Scherer, Raimar J. T1 - Generic Services for the Support of Evolving Building Model Data N2 - Many problems related to data integration in AEC can be better tackled by an approach that takes into account the heterogeneity of tasks, models and applications but does not require continuous consistency of the evolving design data, at each data management operation. Such an approach must incorporate adequate services that can facilitate reintegration of concurrently modified data at reasonably selected coordination points. In this paper we present a set of methods which, used in combination, can achieve that goal. After a description of the principal envisaged cooperative work scenario each of these methods is discussed in detail and current observations drawn from their software realisation are given. Whilst the suggested approach is valid for any EXPRESS-based data model, the practical focus of work has been on facilitating IFC-driven integration. KW - Produktmodell KW - Bautechnik KW - Forschungskooperation KW - EXPRESS Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2077 ER - TY - JOUR A1 - Werner, F. A1 - Eshete, T. T1 - Grundlagen zur Methodik der Verschneidung stahlbautypischer Körper in einem CAD-System N2 - Der Effekt des praktischen Einsatzes von CAD-Systemen im Stahlbau erschöpft sich heute weitgehend in einer Verbesserung der Qualität der Planungsunterlagen und in der Verkürzung der Bearbeitungszeiten. Dabei ist bei schwierigen individuellen Konstruktionen die Einsparung an Arbeitszeit oft nicht sehr markant gegenüber einer traditionellen Arbeitsweise. Die dreidimensionale Erfassung, Speicherung und Verarbeitung von Konstruktionsdaten im Rechner verlangt neben größeren Rechenleistungen neue Verfahren für die Behandlung dieser Daten. Die Möglichkeiten der Automatisierung stahlbautypischer Produktionsvorgänge und einer variablen, computergestützten Planung erfordern wissenschaftlich-technische Betrachtungen des Gesamtproblems. Ausgehend von den Anforderungen des Stahlbaus wird ein neues dreidimensionales Volumenmodell für den rechnergestützten Entwurf und die Konstruktion erarbeitet. Es werden grundlegende Methoden zur Problembehandlung aufgezeigt. Die Methodik basiert im wesentlichen auf der Methode der Inzidenz-Matrizen, um die Beziehungen zwischen topologischen und geometrischen Informationen eines Körpers darzustellen. Die Ermittlung der lokalen Mannigfaltigkeiten wird mit dem Euler-Polyedersatz verglichen und an Beispielen demonstriert. Eine neue Methode zur Ermittlung der lokalen Mannigfaltigkeiten wird dargestellt. Stahlbauspezifische Konstruktionen werden erzeugt und ihre Gestalt nach Anforderungen verändert. Im besonderen werden stahlbauspezifische Ausklinkungen und Verschneidungen erarbeitet und an Beispielen präsentiert. KW - Stahlbau KW - CAD KW - Dreidimensionales Modell Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4601 ER - TY - JOUR A1 - Neumann, K. T1 - Heuristics and applications for Ressource-Constrained Project Scheduling with Minimal and Maximal Time Lags N2 - Priority-rule methods for approximately minimizing the duration of a project subject to minimal and maximal time lags between the activities of the project and limited availability of renewable resources are considered. Such a project can be modelled by a cyclic activity-on-node network. Two generation schemes for constructing feasible schedules are discussed: the serial and parallel schemes. Two different kinds of heuristic procedures are proposed. The sequential or direct method processes the activities or respectively nodes of the project network one after another without considering the strong components separately. The contraction method uses a bottom-up technique. First, a feasible subschedule is determined for each strong component. Second, each strong component is replaced by a single node and the resulting acyclic network is treated by the direct method. In conclusion, some results from an experimental performance analysis of the heuristics are given using a new network generator. KW - Ablaufplanung KW - Beschränkung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5186 ER - TY - JOUR A1 - Makanae, Koji T1 - Highway Sequence Editor based on the Length-based Highway Product Model N2 - The highway product model based on the length information of the centerline, and the application system is developed. This paper shows the schema and the modeling process of the product model, which includes geometric elements such as an alignment, lanes, sidewalks, shoulders and sprits, and accessories such as guard fences, plantings and signs. Furthermore, The Highway Sequence Editor (HSE) is developed as an application system to verify the model. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Straßenbau Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2347 ER - TY - JOUR A1 - Geibig, Oliver A1 - Schnellenbach-Held, Martina T1 - Implementation of an Agent-based Bidding Consortium in the Architecture of an Agent-based Virtual Marketplace N2 - In this research project we intend to transfer the whole AEC-Bidding process to an agent-based virtual marketplace. Hereby, the existing legal regulations have to be considered. Important aspects in developing the virtual marketplace are to provide the possibility to realize an agentbased bidding consortium as well as to integrate subcontractors. KW - Mehragentensystem KW - Lernendes System KW - Ausschreibung KW - Internet Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2214 ER - TY - JOUR A1 - Menzel, Karsten A1 - Mahdavi, A. A1 - Hartkopf, V. A1 - Lee, S. T1 - Information technology for construction management and building performance evaluation support - a North-American perspective N2 - We provide a critical overview of the current status of computational support for construction the management and building performance evaluation in North-America. This overview is based on the research conducted in relation to the design and construction of the Intelligent Workplace (IW), Carnegie Mellon University, Pittsburgh, Pennsylvania, USA. With regard to the commercial software products in the field of construction management the following limitations can be identified: Although project planning, cost estimating and construction simulation are supported, tasks like bidding as well as site and material management have not received the same level of attention. Few project management software packages are integrated in a total design support software system. Little analysis or evaluation options are provided to support managerial decision making. Various research groups address the construction planning and scheduling, construction contracting, site layout generation as well as the integration of these three topics. Currently problems such as efficient material management and calculation of environmental and energy responsive site management are insufficiently addressed within the ongoing research projects. In the domain of building performance simulation and decision support one can notice that, the development and application of computational tools is industry driven. As a result the concerns addressed by the tools are mainly issues pertaining to the selection and sizing of systems and components rather than an integrated performance evaluation. Consequently, these programs are rarely used by building designers, especially in the early design stages, where the predictive capabilities of simulation tools could be of significant value. Although many research institutions address the necessity for the integration of performance simulation within the overall design support environments most of the practically available performance simulation tools still remain mono-dimensional and isolated. KW - Bauausführung KW - Computerunterstütztes Verfahren KW - Bauzustand Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4917 ER -