TY - JOUR A1 - Wiegand, Torben A1 - Osburg, Andrea T1 - Synthesis, Curing and Thermal Behavior of Amine Hardeners from Potentially Renewable Sources JF - Polymers N2 - Research into bio-based epoxy resins has intensified in recent decades. Here, it is of great importance to use raw materials whose use does not compete with food production. In addition, the performance of the newly developed materials should be comparable to that of conventional products. Possible starting materials are lignin degradation products, such as vanillin and syringaldehyde, for which new synthesis routes to the desired products must be found and their properties determined. In this article, the first synthesis of two amine hardeners, starting with vanillin and syringaldehyde, using the Smiles rearrangement reaction is reported. The amine hardeners were mixed with bisphenol A diglycidyl ether, and the curing was compared to isophorone diamine, 4-4′-diaminodiphenyl sulfone, and 4-Aminonbenzylamine by means of differential scanning calorimetry. It was found that the two amines prepared are cold-curing. As TG-MS studies showed, the thermal stability of at least one of the polymers prepared with the potentially bio-based amines is comparable to that of the polymer prepared with isophorone diamine, and similar degradation products are formed during pyrolysis. KW - Epoxide KW - Epoxidharz KW - Polymere KW - epoxy KW - amine hardener KW - curing agent KW - bio-based KW - vanillin KW - OA-Publikationsfonds2023 Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230524-63745 UR - https://www.mdpi.com/2073-4360/15/4/990 VL - 2023 IS - volume 15, issue 4, article 990 SP - 1 EP - 12 PB - MDPI CY - Basel ER - TY - JOUR A1 - Alemu, Yohannes L. A1 - Habte, Bedilu A1 - Lahmer, Tom A1 - Urgessa, Girum T1 - Topologically preoptimized ground structure (TPOGS) for the optimization of 3D RC buildings JF - Asian Journal of Civil Engineering N2 - As an optimization that starts from a randomly selected structure generally does not guarantee reasonable optimality, the use of a systemic approach, named the ground structure, is widely accepted in steel-made truss and frame structural design. However, in the case of reinforced concrete (RC) structural optimization, because of the orthogonal orientation of structural members, randomly chosen or architect-sketched framing is used. Such a one-time fixed layout trend, in addition to its lack of a systemic approach, does not necessarily guarantee optimality. In this study, an approach for generating a candidate ground structure to be used for cost or weight minimization of 3D RC building structures with included slabs is developed. A multiobjective function at the floor optimization stage and a single objective function at the frame optimization stage are considered. A particle swarm optimization (PSO) method is employed for selecting the optimal ground structure. This method enables generating a simple, yet potential, real-world representation of topologically preoptimized ground structure while both structural and main architectural requirements are considered. This is supported by a case study for different floor domain sizes. KW - Bodenmechanik KW - Strukturanalyse KW - Optimierung KW - Stahlbetonkonstruktion KW - Dreidimensionales Modell KW - ground structure KW - TPOGS KW - topology optimization KW - 3D reinforced concrete buildings Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230517-63677 UR - https://link.springer.com/article/10.1007/s42107-023-00640-2 VL - 2023 SP - 1 EP - 11 PB - Springer International Publishing CY - Cham ER - TY - JOUR A1 - Guo, Hongwei A1 - Alajlan, Naif A1 - Zhuang, Xiaoying A1 - Rabczuk, Timon T1 - Physics-informed deep learning for three-dimensional transient heat transfer analysis of functionally graded materials JF - Computational Mechanics N2 - We present a physics-informed deep learning model for the transient heat transfer analysis of three-dimensional functionally graded materials (FGMs) employing a Runge–Kutta discrete time scheme. Firstly, the governing equation, associated boundary conditions and the initial condition for transient heat transfer analysis of FGMs with exponential material variations are presented. Then, the deep collocation method with the Runge–Kutta integration scheme for transient analysis is introduced. The prior physics that helps to generalize the physics-informed deep learning model is introduced by constraining the temperature variable with discrete time schemes and initial/boundary conditions. Further the fitted activation functions suitable for dynamic analysis are presented. Finally, we validate our approach through several numerical examples on FGMs with irregular shapes and a variety of boundary conditions. From numerical experiments, the predicted results with PIDL demonstrate well agreement with analytical solutions and other numerical methods in predicting of both temperature and flux distributions and can be adaptive to transient analysis of FGMs with different shapes, which can be the promising surrogate model in transient dynamic analysis. KW - Wärmeübergang KW - Deep Learning KW - Modellierung KW - physics-informed activation function KW - heat transfer KW - functionally graded materials Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230517-63666 UR - https://link.springer.com/article/10.1007/s00466-023-02287-x VL - 2023 SP - 1 EP - 12 PB - Springer CY - Berlin ER - TY - JOUR A1 - Rabczuk, Timon A1 - Zhuang, Xiaoying A1 - Oterkus, Erkan T1 - Editorial: Computational modeling based on nonlocal theory JF - Engineering with Computers N2 - Nonlocal theories concern the interaction of objects, which are separated in space. Classical examples are Coulomb’s law or Newton’s law of universal gravitation. They had signficiant impact in physics and engineering. One classical application in mechanics is the failure of quasi-brittle materials. While local models lead to an ill-posed boundary value problem and associated mesh dependent results, nonlocal models guarantee the well-posedness and are furthermore relatively easy to implement into commercial computational software. KW - Computersimulation KW - Mathematische Modellierung KW - computational modeling KW - nonlocal theory Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230517-63658 UR - https://link.springer.com/article/10.1007/s00366-022-01775-7 VL - 2023 IS - Volume 39, issue 3 PB - Springer CY - London ER - TY - CHAP A1 - Baron, Nicole A1 - Mandavere, Melody A1 - Cheruiyot, Roselyne T1 - SE/ NPO Ecosystems and urban Governance in Johannesburg T2 - ISTR, Fifteenth International Conference, Montreal, Canada N2 - This paper presents initial findings from the empirical analysis of community based social enterprise (SE) and non-profit organisation (NPO) ecosystems in Johannesburg. SEs and NPOs are widely recognised as contributors to the resilience of marginalised urban communities. However, the connection between these organisations , urban governance, and community resilience has not yet been sufficiently understood , particularly in African urban contexts. The 'Resilient Urban Communities' project focuses on Johannesburg as a case study to shed light on this under-researched topic. The key to exploring it is understanding SEs and NPOs as providers of public services, job creators, and promoters of good governance, all of which contribute to community resilience. Using this premise as a starting point, this paper investigates ecosystem conditions with a particular focus on state-civil society partnerships. Empirical data was generated through semi-struc-tured interviews and analysed with a grounded theory approach. Preliminary results of this ongoing research reveal that urban geography is a relevant ecosystem factor for SEs and NPOs from marginalised communities. We also suggest that co-production could be an opportunity for growth within the investigated state-civil society partnership. KW - Südafrika KW - Johannesburg KW - Nonprofit-Organisation KW - Regionalentwicklung KW - Governance KW - Unterstützungsökosystem KW - Sozialunternehmen Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230517-63643 ER - TY - JOUR A1 - Kraaz, Luise A1 - Koop, Maria A1 - Wunsch, Maximilian A1 - Plank-Wiedenbeck, Uwe T1 - The Scaling Potential of Experimental Knowledge in the Case of the Bauhaus.MobilityLab, Erfurt (Germany) JF - Urban Planning N2 - Real-world labs hold the potential to catalyse rapid urban transformations through real-world experimentation. Characterised by a rather radical, responsive, and location-specific nature, real-world labs face constraints in the scaling of experimental knowledge. To make a significant contribution to urban transformation, the produced knowledge must go beyond the level of a building, street, or small district where real-world experiments are conducted. Thus, a conflict arises between experimental boundaries and the stimulation of broader implications. The challenges of scaling experimental knowledge have been recognised as a problem, but remain largely unexplained. Based on this, the article will discuss the applicability of the “typology of amplification processes” by Lam et al. (2020) to explore and evaluate the potential of scaling experimental knowledge from real-world labs. The application of the typology is exemplified in the case of the Bauhaus.MobilityLab. The Bauhaus.MobilityLab takes a unique approach by testing and developing cross-sectoral mobility, energy, and logistics solutions with a distinct focus on scaling knowledge and innovation. For this case study, different qualitative research techniques are combined according to “within-method triangulation” and synthesised in a strengths, weaknesses, opportunities, and threats (SWOT) analysis. The analysis of the Bauhaus.MobilityLab proves that the “typology of amplification processes” is useful as a systematic approach to identifying and evaluating the potential of scaling experimental knowledge. KW - Stadtplanung KW - Infrastrukturplanung KW - Transformation KW - Reallabor KW - Amplifikationsprozesse KW - Bauhaus.MobilityLab KW - experimentelles Wissen KW - Realexperimente KW - OA-Publikationsfonds2022 Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230509-63633 UR - https://www.cogitatiopress.com/urbanplanning/article/view/5329 VL - 2022 IS - Volume 7, Issue 3 SP - 274 EP - 284 ER - TY - CHAP A1 - Schwendner, Sascha A1 - Völlmecke, Lars A1 - Ho, Ai Phien A1 - Fischer, Jens A1 - Seim, Werner T1 - TESTING OF CONNECTIONS TAKEN FROM OLD NAILED ROOF TRUSSES N2 - Experimental testing of nailed connections taken from old roof trusses is presented in this paper. To enable the further use and preservation of nailed roof trusses, it is important to understand how the nail corrosion and aging processes of steel and wood affect the load-bearing capacity and deformation behaviour of such structures. The hypothesis was investigated whether corroded nails allow an increase in load-bearing capacity. Several old and new joints were tested in a first test series, and the results were very promising regarding the initial assumption. However, more tests must be carried out to verify the results. KW - Holzbau KW - nailed trusses KW - nailed constructions KW - Corrosion KW - Preservation KW - Withdreawal Y1 - 2023 U6 - http://dx.doi.org/10.25643/bauhaus-universitaet.6362 ER - TY - CHAP A1 - Völlmecke, Lars A1 - Schwendner, Sascha A1 - Ho, Ai Phien A1 - Fischer, Jens A1 - Seim, Werner T1 - Assessment of nailed connections in existing structures N2 - This paper presents the development of an assessment scheme for a visual qualitative evaluation of nailed connections in existing structures, such as board trusses. In terms of further use and preservation, a quick visual inspection will help to evaluate the quality of a structure regarding its load-bearing capacity and deformation behaviour. Tests of old and new nailed joints in combination with a rating scheme point out the correlation between the load-bearing capacity and condition of a joint. Old joints of comparatively good condition tend to exhibit better results than those of poor condition. Moreover, aged joints are generally more load-bearing than newly assembled ones. KW - Holzbau KW - Träger KW - nailed trusses KW - nailed constructions KW - Corrosion KW - Preservation KW - Re-use Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230609-63615 ER - TY - GEN A1 - Vollmer, Lisa A1 - Calbet i Elias, Laura A1 - Raab, Susanna A1 - Zanders, Theresa A1 - Kleine, Aya T1 - Ko-Produktion. Ein Handlungsleitfaden für die Zusammenarbeit zwischen zivilgesellschaftlichen Akteuren und öffentlichen Verwaltungen N2 - Dieser Handlungsleitfaden möchte die Zusammenarbeit zwischen zivilgesellschaftlichen Akteuren und öffentlichen Verwaltungen erleichtern. Er enthält allerdings kein Patentrezept, mit dem eine solche Zusammenarbeit gebacken werden kann, sondern vor allem Anstöße, was es dabei alles zu bedenken gilt. Denn Ko-Produktionsprozesse, bei denen zivilgesellschaftliche Gruppen und Verwaltungen gemeinsam an der Umsetzung von Dienstleistungen und Infrastrukturen der Daseinsvorsorge arbeiten, sind komplexe und noch recht unerprobte Prozesse. T3 - KoopWohl - Working Paper - 6 KW - Koproduktion Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230413-49549 ET - Erste Auflage ER - TY - THES A1 - Cicek, Burhan A1 - Cancino, Pamela T1 - Küreken 2013. Entwerfen eines Dorfes aus Lehm N2 - Die Diskussionen in der Politik und in der Gesellschaft über Klimawandel, globale Erwärmung oder Nachhaltigkeit, die schon noch länger anhält, werden nie ein Ende finden, solange die Probleme, auf denen sie basiert, unlösbar bleiben. Vorgeschlagene Lösungen werden meist nicht richtig umgesetzt. Im Zusammenhang mit dieser Problematik steigt aber das Verantwortungsgefühl für bessere Zukunftsstrategien immer mehr. Die in den letzten Jahren vorgekommenen Umweltkatastrophen, wie im Golf von Mexiko (April 2010) oder im Fukushima (März 2011) die noch aktuell sind, zeigen, dass der Primärenergieeinsatz oder die Transportproblematik nicht mehr nur die Sorge der Entwicklungsländer, sondern auch der Industrieländer ist. Die Bauwelt mit ihrem erheblichen Energiebedarf spielt bei der Festlegung der Zukunftsstrategien eine große Rolle. Vor allem sind die Forschungen nach umweltfreundlichen Materialien, der Recyclebarkeit der eingesetzten Baumaterialien oder dem vernünftigen Nutzen der Naturressourcen die wichtigsten Schwerpunkte. In dieser Hinsicht bringt Lehm als Baumaterial viele Vorteile mit sich. Bei einem Artikel sagt der Lehmbauexperte Martin Rauch: “In heutiger Zeit und einem Kulturkreis, in dem Baugrund und Arbeitszeit unsere großen Kosten verursachen, findet der tradierte Lehmbau mit dem verbundenen großen Aufwand an menschlicher Arbeitszeit nur schwer seinen Platz. Über die Art der Bauweise wird auch die Entscheidung gefällt, wie und wo die Wertschöpfung erfolgt und ob der Einsatz des Budgets einen gesellschaftlichen Nutzen mit sich bringt. Im Vergleich zu einem Sichtbetonhaus können bei einem Stampflehmhaus 40% der Primärenergie ein gespart und dafür mehr lokale Arbeitsressourcen gebunden werden. Davon profitieren vor allem die lokalen Handwerker und mittelständischen Betriebe” Anatolien ist der Ort, wo man immer noch die tiefsten Wurzeln der Baukultur menschlicher Geschichte findet. Diese Baukultur, die in den vergangenen Jahrzehnten fast verlorengegangen ist, ist die Lehmbaukultur. In dieser Hinsicht beabsichtigt dieser Entwurf die Würde des Lehms in Anatolien wieder herzustellen und dadurch dessen Glaubwürdigkeit zurückzubringen. KW - Lehm KW - Lehmbau KW - stabilisierter Lehm KW - Stampflehm KW - Alker Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20240507-63568 ER - TY - THES A1 - Dokhanchi, Najmeh Sadat T1 - Measurement of the Indoor Air Temperature Distribution using Acoustic Travel-Time Tomography N2 - One of the main criteria determining the thermal comfort of occupants is the air temperature. To monitor this parameter, a thermostat is traditionally mounted in the indoor environment for instance in office rooms in the workplaces, or directly on the radiator or in another location in a room. One of the drawbacks of this conventional method is the measurement at a certain location instead of the temperature distribution in the entire room including the occupant zone. As a result, the climatic conditions measured at the thermostat point may differ from those at the user's location. This not only negatively impacts the thermal comfort assessment but also leads to a waste of energy due to unnecessary heating and cooling. Moreover, for measuring the distribution of the air temperature under laboratory conditions, multiple thermal sensors should be installed in the area under investigation. This requires high effort in both installation and expense. To overcome the shortcomings of traditional sensors, Acoustic travel-time TOMography (ATOM) offers an alternative based on measuring the transmission sound velocity signals. The basis of the ATOM technique is the first-order dependency of the sound velocity on the medium's temperature. The average sound velocity, along the propagation paths, can be determined by travel-times estimation of a defined acoustic signal between transducers. After the travel-times collection, the room is divided into several volumetric grid cells, i.e. voxels, whose sizes are defined depending on the dimension of the room and the number of sound paths. Accordingly, the spatial air temperature in each voxel can be determined using a suitable tomographic algorithm. Recent studies indicate that despite the great potential of this technique to detect room climate, few experiments have been conducted. This thesis aims to develop the ATOM technique for indoor climatic applications while coupling the analysis methods of tomography and room acoustics. The method developed in this thesis uses high-energy early reflections in addition to the direct paths between transducers for travel time estimation. In this way, reflections can provide multiple sound paths that allow the room coverage to be maintained even when a few or even only one transmitter and receiver are used. In the development of the ATOM measurement system, several approaches have been employed, including the development of numerical methods and simulations and conducting experimental measurements, each of which has contributed to the improvement of the system's accuracy. In order to effectively separate the early reflections and ensure adequate coverage of the room with sound paths, a numerical method was developed based on the optimization of the coordinates of the sound transducers in the test room. The validation of the optimal positioning method shows that the reconstructed temperatures were significantly improved by placing the transducers at the optimal coordinates derived from the developed numerical method. The other numerical method developed is related to the selection of the travel times of the early reflections. Accordingly, the detection of the travel times has been improved by adjusting the lengths of the multiple analysis time-windows according to the individual travel times in the reflectogram of the room impulse response. This can reduce the probability of trapping faulty travel times in the analysis time-windows. The simulation model used in this thesis is based on the image source model (ISM) method for simulating the theoretical travel times of early reflection sound paths. The simulation model was developed to simulate the theoretical travel times up to third-order reflections. The empirical measurements were carried out in the climate lab of the Chair of Building Physics under different boundary conditions, i.e., combinations of different room air temperatures under both steady-state and transient conditions, and different measurement setups. With the measurements under controllable conditions in the climate lab, the validity of the developed numerical methods was confirmed. In this thesis, the performance of the ATOM measurement system was evaluated using two measurement setups. The setup for the initial investigations consists of an omnidirectional receiver and a near omnidirectional sound source, keeping the number of transducers as few as possible. This has led to accurately identify the sources of error that could occur in each part of the measuring system. The second measurement setup consists of two directional sound sources and one omnidirectional receiver. This arrangement of transducers allowed a higher number of well-detected travel times for tomography reconstruction, a better travel time estimation due to the directivity of the sound source, and better space utilization. Furthermore, this new measurement setup was tested to determine an optimal selection of the excitation signal. The results showed that for the utilized setup, a linear chirp signal with a frequency range of 200 - 4000 Hz and a signal duration of t = 1 s represents an optimal selection with respect to the reliability of the measured travel times and higher signal-to-noise ratio (SNR). To evaluate the performance of the measuring setups, the ATOM temperatures were always compared with the temperatures of high-resolution NTC thermistors with an accuracy of ±0.2 K. The entire measurement program, including acoustic measurements, simulation, signal processing, and visualization of measurement results are performed in MATLAB software. In addition, to reduce the uncertainty of the positioning of the transducers, the acoustic centre of the loudspeaker was determined experimentally for three types of excitation signals, namely MLS (maximum length sequence) signals with different lengths and duration, linear and logarithmic chirp signals with different defined frequency ranges. For this purpose, the climate lab was converted into a fully anechoic chamber by attaching absorption panels to the entire surfaces of the room. The measurement results indicated that the measurement of the acoustic centre of the sound source significantly reduces the displacement error of the transducer position. Moreover, to measure the air temperature in an occupied room, an algorithm was developed that can convert distorted signals into pure reference signals using an adaptive filter. The measurement results confirm the validity of the approach for a temperature interval of 4 K inside the climate lab. Accordingly, the accuracy of the reconstructed temperatures indicated that ATOM is very suitable for measuring the air temperature distribution in rooms. T3 - Schriftenreihe der Professur Bauphysik - 8 KW - Bauphysik KW - Acoustic Travel-Time Tomography KW - Bauklimatik Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230414-49567 SN - 978-3-00-075344-2 (print) ER - TY - JOUR A1 - Simon-Ritz, Frank T1 - "Kultur ist Reichtum an Problemen": Wie sich der Kultur-Begriff der UNESCO an Egon Friedell annäherte JF - Palmbaum: Literarisches Journal aus Thüringen N2 - Der in H. 1/2023 erschienene Essay führt Gedanken einer in H. 1/2022 des "Palmbaum" erschienene Betrachtung (https://doi.org/10.25643/bauhaus-universitaet.4628) weiter. Im Zentrum stehen dabei die Bemühungen der UNESCO um das immaterielle Kulturerbe. KW - UNESCO KW - Kulturerbe Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230411-49524 VL - 2023 IS - Heft 1 PB - Quartus Verlag CY - Bucha bei Jena ER - TY - JOUR A1 - Londong, Jörg A1 - Barth, Marcus A1 - Söbke, Heinrich T1 - Reducing antimicrobial resistances by source separation of domestic wastewater JF - Frontiers in Environmental Health N2 - Antimicrobial resistances (AMR) are ranked among the top ten threats to public health and societal development worldwide. Toilet wastewater contained in domestic wastewater is a significant source of AMR entering the aquatic environment. The current commonly implemented combined sewer systems at times cause overflows during rain events, resulting in the discharge of untreated wastewater into the aquatic environment, thus promoting AMR. In this short research article, we describe an approach to transform combined sewer systems into source separation-modified combined sewer systems that separately treat toilet wastewater. We employ simulations for demonstrating that source separation-modified combined sewer systems reduce the emission of AMR- causing substances by up to 11.5 logarithm levels. Thus, source separation- modified combined sewer systems are amongst the most effective means of combating AMR. KEYWORDS KW - Allgemeinheit KW - Öffentlichkeit KW - Gesundheit KW - Kanal KW - Abwasser KW - Antibiotikum KW - Resistenz KW - OA-Publikationsfonds2023 Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230403-49483 UR - https://www.frontiersin.org/articles/10.3389/fenvh.2023.1151898/full VL - 2023 IS - Volume 2, article 1151898 SP - 1 EP - 5 PB - Frontiers Media CY - Lausanne ER - TY - JOUR A1 - Wellbrock, Christian-Mathias A1 - Lobigs, Frank A1 - Erbrich, Lukas A1 - Buschow, Christopher T1 - Coopetition is King. Ökonomische Potentiale und medienpolitische Implikationen kooperativer Journalismusplattformen N2 - Die vorliegende Studie geht der Fragestellung nach, wie sich eine anbieterübergreifende, abonnementbasierte Plattform für den digitalen Journalismus, also eine Art Spotify im Journalismus, auf die Umsätze der Anbieter journalistischer Inhalte und die Abonnements im Digitaljournalismus in Deutschland auswirken würde. Auf Basis drei sich ergänzender Schätzmethoden für Zahlungsbereitschaft, die in zwei Repräsentativbefragungen der deutschen Online-Bevölkerung mit insgesamt 8.000 Teilnehmenden angewandt wurden, gelangt das Whitepaper zu den folgenden Schlüsselbefunden. KW - Journalistik KW - Nachrichtensendung KW - Online-Medien KW - Geschäftsmodell KW - Journalismusplattform KW - Journalismusförderung KW - Digitaljournalismus KW - Abonnement KW - Studie Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230320-49473 VL - 2023 SP - 1 EP - 48 PB - Landesanstalt für Medien NRW CY - Düsseldorf ER - TY - JOUR A1 - Ansari, Meisam A1 - Zacharias, Christin A1 - Könke, Carsten T1 - Metaconcrete: An Experimental Study on the Impact of the Core-Coating Inclusions on Mechanical Vibration JF - materials N2 - Resonance vibration of structures is an unpleasant incident that can be conventionally avoided by using a Tuned Mass Damper (TMD). The scope of this paper contains the utilization of engineered inclusions in concrete as damping aggregates to suppress resonance vibration similar to a TMD. The inclusions are composed of a stainless-steel core with a spherical shape coated with silicone. This configuration has been the subject of several studies and it is best known as Metaconcrete. This paper presents the procedure of a free vibration test conducted with two small-scaled concrete beams. The beams exhibited a higher damping ratio after the core-coating element was secured to them. Subsequently, two meso-models of small-scaled beams were created: one representing conventional concrete and the other representing concrete with the core-coating inclusions. The frequency response curves of the models were obtained. The change in the response peak verified the ability of the inclusions to suppress the resonance vibration. This study concludes that the core-coating inclusions can be utilized in concrete as damping aggregates. KW - Beton KW - Schwingungsdämpfung KW - metaconcrete KW - damping aggregate KW - vibration absorber Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230315-49370 UR - https://www.mdpi.com/1996-1944/16/5/1836 VL - 2023 IS - Volume 16, Issue 5, article 1836 SP - 1 EP - 18 PB - MDPI CY - Basel ER - TY - THES A1 - Drescher, Marcel T1 - Open Innovation in KMU - Eine empirische Analyse der offenen Innovationsaktivitäten im Kontext der Entrepreneurial Orientation N2 - Open Innovation in kleinen und mittleren Unternehmen (KMU) hat sich stark ausdifferenziert. Dabei zeigt die Empirie, dass KMU unterschiedliche Wege in der offenen Entwicklung von Innovationen begehen. Um die bestehende Literatur zu erweitern, wurden mit dieser Dissertation die Ziele verfolgt 1) offene Innovationsaktivitäten in KMU aus einer Prozessperspektive aufzudecken und genau zu beschreiben und 2) zu erklären, warum sich die Öffnung von Innovationsprozessen in KMU unterscheidet. Dafür wurde auf eine multiple Fallstudienanalyse zurückgegriffen. Untersuchungsobjekte waren kleine etablierte High-Tech Unternehmen aus den neuen Bundesländern. Die Ergebnisse zeigen sechs Prozessmodelle der offenen Innovationsentwicklung, beschrieben als Open Innovation Muster. Deskriptionen dieser Muster unter Berücksichtigung von formenden Innovationsaktivitäten, ausgetauschtem Wissen, beteiligten externen Akteuren und Gründen für und gegen Open Innovation vermitteln ein über den bisherigen Forschungsstand hinausgehendes Verständnis von Open Innovation in KMU. Zudem zeigen die Ergebnisse, dass die Entrepreneurial Orientation erklärt, warum KMU bei der Ausgestaltung von offenen Innovationsprozessen unterschiedlich vorgehen. In der Dissertation wird detailliert dargelegt, welche Open Innovation Muster sich anhand der Entrepreneurial Orientation von KMU (nicht-entrepreneurial bis entrepreneurial) zeigen. Die Ergebnisse liefern sowohl wissenschaftliche Implikationen, als auch Handlungsempfehlungen für die Unternehmenspraxis. KW - Open Innovation KW - Innovationsmanagement KW - Entrepreneurship KW - Klein- und Mittelbetrieb KW - KMU KW - Entrepreneurial Orientation Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230314-49463 ER - TY - THES A1 - Gapševičius, Mindaugas T1 - Aesthetics of Maker Culture: the Active Role of the Audience N2 - In this work, practice-based research is conducted to rethink the understanding of aesthetics, especially in relation to current media art. Granted, we live in times when technologies merge with living organisms, but we also live in times that provide unlimited resources of knowledge and maker tools. I raise the question: In what way does the hybridization of living organisms and non-living technologies affect art audiences in the culture that may be defined as Maker culture? My hypothesis is that active participation of an audience in an artwork is inevitable for experiencing the artwork itself, while also suggesting that the impact of the umwelt changes the perception of an artwork. I emphasize artistic projects that unfold through mutual interaction among diverse peers, including humans, non-human organisms, and machines. In my thesis, I pursue collaborative scenarios that lead to the realization of artistic ideas: (1) the development of ideas by others influenced by me and (2) the materialization of my own ideas influenced by others. By developing the scenarios of collaborative work as an artistic experience, I conclude that the role of an artist in Maker culture is to mediate different types of knowledge and different positions, whereas the role of the audience is to actively engage in the artwork itself. At the same time, aesthetics as experience is triggered by the other, including living and non-living actors. It is intended that the developed methodologies could be further adapted in artistic practices, philosophy, anthropology, and environmental studies. KW - Medienkunst KW - BioArt KW - Media art KW - BioArt KW - Maker Culture Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230313-49396 ER - TY - THES A1 - Hunger, Francis T1 - Die Form der Datenbank N2 - Datenbanken sind heute die wichtigste Technik zur Organisation und Verarbeitung von Daten. Wie wurden sie zu einer der allgegenwärtigsten und gleichzeitig unsichtbarsten Praxis, die menschliche Zusammenarbeit ermöglicht? Diese Studie beginnt mit einer historiographischen Erkundung der zentralen medialen Konzepte von Datenbanken und mündet in das praxeologische Konzept der "Daten als Formation", kurz: In-Formation. Der erste Hauptteil befasst sich mit der Formatierung von Daten durch die Verarbeitung strukturierter Daten mittels relationaler Algebra. Es wird erarbeitet, auf welche Weise Struktur neues Wissen schafft. Im zweiten Teil wird erörtert, wie Datenbanken durch den diagrammatisch-epistemischen Raum der Tabelle operationalisiert werden. Drittens untersucht die Studie Transaktionen als Erklärungen dafür, wie Daten und reale Handlungen koordiniert und synchronisiert werden können. Im zweiten Hauptteil wird untersucht, wie relationale Datenbanken zunehmend zum Zentrum von Softwareanwendungen und Infrastrukturen wurden, wobei der Schwerpunkt auf wirtschaftlichen Praktiken liegt. In einem vergleichenden Ansatz wird anhand von Fallstudien in der DDR der 1970er bis 1990er Jahren die Frage gestellt, ob es eine „sozialistische“ Datenbankmanagement-Software gegeben hat. Dabei werden die „westlichen“ Produktionsdatenbanken BOMP, COPICS und MAPICS (IBM) sowie R2 (SAP) im Zusammenspiel mit den ostdeutschen Sachgebietsorientierten Programmiersystemen (SOPS) von Robotron diskutiert. Schließlich untersucht dieser Teil, wie die DDR ihr eigenes relationales Datenbankmanagementsystem, DABA 1600, entwickelte und dabei „westliche“ Technologie neu interpretierte. Das abschließende Kapitel fasst die Konzepte der relationalen Datenbanken als heute wichtigsten Datenorganisationstechnik zusammen. Es erörtert, inwiefern es möglich ist, die historiographische Erzählung über die Entstehung von Datenbankmanagementsystemen und ihre Folgen für die Geschichte der Informatik zu dezentrieren. Es schließt mit der Erkenntnis, dass östliche und westliche Medien der Kooperation sich in Form und Funktion erstaunlich ähnlich sind, beide wurzeln in den tiefen Genealogien von organisatorischen und wissensbildenden Datenpraktiken. Neben dieser medienwissenschaftlichen Arbeit besteht die Dissertation aus einem künstlerischen Teil, der dokumentiert wird: Anhand einer Reihe von Vlogs erkundet die fiktionale Figur „Data Proxy“ aktuelle Datenökologien. KW - Medientheorie KW - Datenbank KW - Medienkunst KW - Software KW - Datenbanken KW - Software-Studies KW - Geschichte des Computing KW - Medientheorie KW - Daten Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230306-49362 ER - TY - THES A1 - Jaouadi, Zouhour T1 - Pareto and Reliability-Oriented Aeroelastic Shape Optimization of Bridge Decks N2 - Due to the development of new technologies and materials, optimized bridge design has recently gained more attention. The aim is to reduce the bridge components materials and the CO2 emission from the cement manufacturing process. Thus, most long-span bridges are designed to be with high flexibility, low structural damping, and longer and slender spans. Such designs lead, however, to aeroelastic challenges. Moreover, the consideration of both the structural and aeroelastic behavior in bridges leads to contradictory solutions as the structural constraints lead to deck prototypes with high depth which provide high inertia to material volume ratios. On the other hand, considering solely the aerodynamic requirements, slender airfoil-shaped bridge box girders are recommended since they prevent vortex shedding and exhibit minimum drag. Within this framework comes this study which provides approaches to find optimal bridge deck cross-sections while considering the aerodynamic effects. Shape optimization of deck cross-section is usually formulated to minimize the amount of material by finding adequate parameters such as the depth, the height, and the thickness and while ensuring the overall stability of the structure by the application of some constraints. Codes and studies have been implemented to analyze the wind phenomena and the structural responses towards bridge deck cross-sections where simplifications have been adopted due to the complexity and the uniqueness of such components besides the difficulty of obtaining a final model of the aerodynamic behavior. In this thesis, two main perspectives have been studied; the first is fully deterministic and presents a novel framework on generating optimal aerodynamic shapes for streamlined and trapezoidal cross-sections based on the meta-modeling approach. Single and multi-objective optimizations were both carried out and a Pareto Front is generated. The performance of the optimal designs is checked afterwards. In the second part, a new strategy based on Reliability-Based Design Optimization (RBDO) to mitigate the vortex-induced vibration (VIV) on the Trans-Tokyo Bay bridge is proposed. Small changes in the leading and trailing edges are presented and uncertainties are considered in the structural system. Probabilistic constraints based on polynomial regression are evaluated and the problem is solved while applying the Reliability Index Approach (RIA) and the Performance Measure Approach (PMA). The results obtained in the first part showed that the aspect ratio has a significant effect on the aerodynamic behavior where deeper cross-sections have lower resistance against flutter and should be avoided. In the second part, the adopted RBDO approach succeeded to mitigate the VIV, and it is proven that designs with narrow or prolonged bottom-base length and featuring an abrupt surface change in the leading and trailing edges can lead to high vertical vibration amplitude. It is expected that this research will help engineers with the selections of the adequate deck cross-section layout, and encourage researchers to apply concepts of optimization regarding this field and develop the presented approaches for further studies. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,10 KW - Gestaltoptimierung KW - Vibration KW - Deck cross-sections KW - Reliability-based design optimization KW - Shape optimization KW - Pareto Front KW - Vortex-induced vibration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230303-49352 ER - TY - THES A1 - Weise, Franziska T1 - Erfolgskritische Faktoren in exemplarischen Building Information Modeling Anwendungsfällen: Eine Analyse unter der Beachtung schleppender Digitalisierung und organisationaler Veränderungen N2 - Die fortschreitende Digitalisierung lässt innovative bauprojekt- und unternehmensinterne Workflows sowie Organisationssysteme entstehen. In diesem Zusammenhang ist die digitale Fortentwicklung durch Building Information Modeling [BIM] als Veränderungsprozess zu definieren, der Organisationsstrukturen nachhaltig umformen wird. BIM ist die führende digitale Arbeitsmethodik im Bauwesen, die entwurfs-, ausführungs- und bauprojektbezogenen Belangen gerecht werden kann. Die deutsche Bauwirtschaft ist im Vergleich zu anderen Branchen jedoch als digital rückständig zu betrachten. Sie ist durch einen Markt gekennzeichnet, an dem kleine und mittelständische Unternehmen [KMU] in hoher Zahl vertreten sind. Aufgrund von Anwendungsunkenntnis der kleinen und mittelständischen Unternehmen fehlt der flächendeckende und durchgängige BIM-Einsatz in Projekten. Mit dem Fokus auf dem Bauprojekt als temporärer Organisation adressiert der vorliegende Forschungsschwerpunkt die Schaffung eines realistischen Abbilds erprobter BIM-Anwendungsfälle in Modellprojekten. Herausgearbeitet werden derzeit bestehende BIM-Herausforderungen für Erstanwender, die die durchgängige BIM-Anwendung in Deutschland bisher hemmen. Die Forschungsarbeit fokussiert sich auf die Evaluation erfolgskritischer Faktoren [ekF] in BIM-Anwendungsfällen [AWF] im Rahmen einer qualitativen Inhaltsanalyse. Die digitale Transformation birgt strukturrelevante Veränderungsdeterminanten für Organisationen durch die BIM-Anwendung und außerdem Herausforderungen, die in der Anwendungsfallforschung betrachtet werden. Die Zielstellung ist dreiteilig. Ein entwickeltes BIM-Strukturmodell erfasst die aktuelle Richtlinienarbeit sowie Standardisierung und stellt dadurch den Rahmen notwendiger BIM-Strukturen im Bauprojekt auf. Aus dem Strukturmodell ist ein Modell zur Prüfung von Anwendungsfallrisiken abgeleitet worden. Dieses wird auf gezielt recherchierte BIM-Modellprojekte in Deutschland angewendet, um aus den erfolgskritischen Faktoren der darin praktizierten BIM-Anwendungsfälle eine ekF-Risikomatrix abzuleiten. Daraus geht ein unterstützendes BIM-Anwendungsinstrument in Form von BPMN-Abläufen für KMU hervor. Resultierend aus der Verbindung des BIM-Strukturmodels und der Anwendungsfallanalyse wird in den einzelnen Ablaufübersichten eine Risikoverortung je Anwendungsfall kenntlich gemacht. Unternehmen ohne BIM-Anwendungsexpertise in Bauprojektorganisationen erhalten auf diese Weise einen instrumentellen und niederschwelligen Zugang zu BIM, um die kollaborativen und wirtschaftlichen Vorteile der digitalen Arbeitsmethodik nutzen zu können. T3 - Schriften der Professur Baubetrieb und Bauverfahren - 41 KW - Building Information Modeling KW - Gebäudedaten-Modellierung KW - digitale Organisation Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230302-49281 PB - Eigenverlag der Professur Baubetrieb und Bauverfahren CY - Weimar ER -