TY - JOUR A1 - Nagel, Falk A1 - Simon, Flaviu A1 - Kümmel, Benjamin A1 - Bergmann, Jean Pierre A1 - Hildebrand, Jörg T1 - Optimization Strategies for Laser Welding High Alloy Steel Sheets JF - Physics Procedia N2 - A known phenomenon during laser welding of thin sheets is the deformation caused by thermally induced stresses. This deformation can result in a change of the gap width between the welded parts, which leads to an unstable welding process. Inducing displacements by using a second heat source will compensate for the change in gap width, hence optimizing the welding process. The base material is 1 mm thick austenitic stainless steel 1.4301, which is welded by a CO2 laser. The second heat source is a diode laser. The gap between the welded parts was set between 0.05 mm and 0.1 mm. The influence of the second heat source on the welding process and the welding result is described. The usage of a second heat source allows a higher gap width to be set prior to the welding process. The results of the numerical simulation were found to be corresponding to those of the experiments. KW - Edelstahl KW - Laserschweißen KW - Laser Welding; CO2; Diode; Distortion; Finite Element Analysis; Thermal Analysis; Mechanical Analysis; Numerical Model Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170425-31554 SP - 1242 EP - 1251 ER - TY - JOUR A1 - Linnow, Kirsten A1 - Niermann, Michael A1 - Bonatz, Dennis A1 - Posern, Konrad A1 - Steiger, Michael T1 - Experimental Studies of the Mechanism and Kinetics of Hydration Reactions JF - Energy Procedia N2 - The mechanism and the kinetics of hydration reactions are important for the application of a salt hydrate as a thermochemical heat storage material. MgSO4·H2O and Na2SO4 were chosen in this study because they are both promising candidates for such an application. Considering that the hydration of these salts yields MgSO4·7H2O and Na2SO4·10H2O as the reaction products, the maximum overall heat effect can be calculated from the heat of condensation of water vapor (44 kJ mol–1) and the heats of hydration of 75 kJ·mol-1 (for MgSO4·H2O) and 81 kJ mol-1 (for Na2SO4). Based on the densities of the two hydrated phases, this results in the very high theoretical energy densities of 2.3 GJ·m-3 and 2.4 GJ·m-3, respectively, for MgSO4·7H2O and Na2SO4·10H2O. Not only the energy density is important for the dimensioning of a storage system, but also the kinetics of hydration reactions play a major role for the application as storage material. In the present study, hydration reactions under varying climatic conditions were investigated by using water vapor sorption measurements and in-situ Raman microscopy. Using the phase diagrams, it can be clearly shown that the mechanism and the kinetics depend on the climatic conditions. Below the deliquescence humidity of the lower hydrated phase the hydration proceeds as solid state reaction, whilst above the deliquescence humidity a through solution mechanism takes place. KW - Wärmespeicherung KW - Hydratation KW - Magnesiumsulfat KW - Natriumsulfat KW - hermochemical heat storage, hydration mechanism, magnesium sulfate; sodium sulfate Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170425-31484 SP - 394 EP - 404 ER - TY - JOUR A1 - Ataollahi Oshkour, Azim A1 - Talebi, Hossein A1 - Seyed Shirazi, Seyed Farid A1 - Bayat, Mehdi A1 - Yau, Yat Huang A1 - Tarlochan, Faris A1 - Abu Osman, Noor Azuan T1 - Comparison of various functionally graded femoral prostheses by finite element analysis JF - Scientific World Journal N2 - This study is focused on finite element analysis of a model comprising femur into which a femoral component of a total hip replacement was implanted. The considered prosthesis is fabricated from a functionally graded material (FGM) comprising a layer of a titanium alloy bonded to a layer of hydroxyapatite. The elastic modulus of the FGM was adjusted in the radial, longitudinal, and longitudinal-radial directions by altering the volume fraction gradient exponent. Four cases were studied, involving two different methods of anchoring the prosthesis to the spongy bone and two cases of applied loading. The results revealed that the FG prostheses provoked more SED to the bone. The FG prostheses carried less stress, while more stress was induced to the bone and cement. Meanwhile, less shear interface stress was stimulated to the prosthesis-bone interface in the noncemented FG prostheses. The cement-bone interface carried more stress compared to the prosthesis-cement interface. Stair climbing induced more harmful effects to the implanted femur components compared to the normal walking by causing more stress. Therefore, stress shielding, developed stresses, and interface stresses in the THR components could be adjusted through the controlling stiffness of the FG prosthesis by managing volume fraction gradient exponent. KW - Finite-Elemente-Methode KW - Hüftgelenk KW - Funktioneller Gradientenwerkstoff Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170413-31194 ER - TY - JOUR A1 - Masood, R. A1 - Kharal, M. K. N. A1 - Nasir, A.R. T1 - Is BIM Adoption Advantageous for Construction Industry of Pakistan? JF - Procedia Engineering N2 - Lack of Information technology applications on construction projects lead to complex flow of data during project life cycle. Building Information Modeling (BIM) has gained attention in the Architectural, Engineering and Construction (AEC) industry, envisage the use of virtual n-dimensional (n-D) models to identify potential conflicts in design, construction or operational of any facility. A questionnaire has been designed to investigate perceptions regarding BIM advantages. Around 102 valid responses received from diversified stakeholders. Results showed very low BIM adoption with low level of ‘Buzz’. BIM is a faster and more effective method for designing and construction management, it improves quality of the design and construction and reduces rework during construction; which came out as the top thee advantages according to the perception of AEC professionals of Pakistan.BIM has least impact on reduction of cost, time and human resources. This research is a bench mark study to understand adoption and advantageous of BIM in Pakistan Construction Industry. KW - Building Information Modeling KW - Bauindustrie KW - Pakistan KW - BIM, BIM Adoption, BIM Advantages , Construction Industry, Pakistan Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170425-31509 SP - 229 EP - 238 ER - TY - JOUR A1 - Massaretti, Pier Giorgio T1 - Dagli inizi dell’urbanismo teorico alla città moderna. Visioni urbanistiche del totalitarismo – Italia JF - Anthologie zum Städtebau. Das Phänomen Großstadt und die Entstehung der Stadt der Moderne N2 - La prima edizione di questo testo è apparsa, in tedesco, nel volume II.2.: Anthologie zum Städtebau. Das Phänomen Großstadt und die Entstehung der Stadt der Moderne, a cura di Vittorio Magnago Lampugnani, Katia Frey, Eliana Perotti, con il sostegno di Departement Architektur der Eidgenössischen Technischen Hochschule, Zürich (Gebr. Mann Verlag, Berlin 2014, pp. 1307-1390). Previ specifici accordi con l’editore, viene qui presentata la versione originaria, in italiano, dell’intero capitolo: Modernität und Emphase. Städtebau im italienischen Faschismus, e comprendente: i) una capiente saggio introduttivo – in una versione più ampia ed articolata (comprensiva della “Bibliografia sistematica”, di riferimento) del testo in tedesco; ii) la versione in italiano del repertorio antologico di riferimento – e comprensiva di una “Scheda introduttiva”, sull’Autore-Opera, e di una selezione del testo in esame. KW - Städtebau Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170529-32228 SP - 1 EP - 45 ER - TY - CHAP A1 - Massaretti, Pier Giorgio T1 - La ri-fondazione della Libia balbiana (1933-1939). Il poderoso racconto fotografico dei “Ventimila” T2 - Città mediterranee in trasformazione N2 - La prima edizione di questo testo è apparsa negli atti del VI Convegno Internazionale di Studi del CIRICE – Centro Interdipartimentale di Ricerca sull’Iconografia della Città Europea − Università di Napoli Federico II, (Napoli, 13-15 marzo 2014), dal titolo: Città mediterranee in trasformazione. Identità e immagine del paesaggio urbano tra Sette e Novecento, a cura di A. Buccaro e C. de Seta (Collana: Polis, 6; Napoli: Edizioni Scientifiche Italiane, 2014; pp. 1216; ISBN 9788849528145), all’interno della sessione 7, Le trasformazioni del paesaggio urbano nella fotografia e nella cinematografia, coordinatori: F. Capano, M. Iuliano, pp. 1085-1098. Il Convegno, aperto a studiosi di ambito nazionale e internazionale, si poneva l’obiettivo di fare il punto sulla storiografia riguardante la città mediterranea in età contemporanea, con particolare riferimento alla sua identità, struttura e immagine, dall’inizio dell’industrializzazione all’età post-illuminista e borghese, fino ai temi inerenti l’evoluzione/involuzione del territorio e del paesaggio post-industriale, nonché lo sviluppo del modello turistico tra Otto e Novecento. KW - Städtebau Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170529-32234 ER - TY - THES A1 - Itam, Zarina T1 - Numerical Simulation of Thermo-Chemo-Hygro-Mechanical Alkali-Silica Reaction Model in Concrete at the Mesoscale and Macroscale N2 - Alkali-silica reaction causes major problems in concrete structures due to the rapidity of its deformation which leads to the serviceability limit of the structure being reached well before its time. Factors that affect ASR vary greatly, including alkali and silica content, relative humidity, temperature and porosity of the cementitious matrix,all these making it a very complex phenomenon to consider explicitly. With this in mind, the finite element technique was used to build models and generate expansive pressures and damage propagation due to ASR under the influence of thermo-hygrochemoelastic loading. Since ASR initializes in the mesoscopic regions of the concrete, the accumulative effects of its expansion escalates onto the macroscale level with the development of web cracking on the concrete surface, hence solution of the damage model as well as simulation of the ASR phenomenon at both the macroscale and mesoscale levels have been performed. The macroscale model realizes the effects of ASR expansion as a whole and shows how it develops under the influence of moisture, thermal and mechanical loading. Results of the macroscale modeling are smeared throughout the structure and are sufficient to show how damage due to ASR expansion orientates. As opposed to the mesoscale model, the heterogeneity of the model shows us how difference in material properties between aggregates and the cementitious matrix facilitates ASR expansion. With both these models, the ASR phenomenon under influence of thermo-chemo-hygro-mechanical loading can be better understood. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2014,2 KW - Strukturmechanik KW - Alkali-silica reaction KW - macroscale KW - mesoscale KW - ASR Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20141218-23352 ER - TY - THES A1 - Torrado, Valentina T1 - Die Präsenz des Abjekten in der zeitgenössischen Kunstproduktion N2 - Die Arbeit fokussiert die Rolle des Abjekten in der zeitgenössischen Kunst und hier insbesondere die Rolle der Künstler aus den wohlhabenden – sogenannten postindustriellen – Ländern. Die Arbeit mit abjekten Themen in der Kunstproduktion ist sehr präsent, jedoch aus einer anderen, eher individualistischen Perspektive. Die wichtigsten Orte der Kunst (Galerien, Museen, Kulturzentren) sind Räume der Legitimation dieser Art von Produktion, dabei wird das Potential der Provokation hinterfragt. Die klassische Avantgarde, besonders der Dadaismus, hat das Abjekte zu Beginn des 20. Jahrhunderts als künstlerisches Material genutzt. Das Spiel mit Grenzüberschreitungen durch die Darstellung des Verbotenen und Ekelerregenden machte das Abjekte zur produktiven Kraft auch auf sozialer Ebene, weil es als Mittel dem gesellschaftlichen Protest und der sozialen Kritik diente. KW - Abjekt KW - Ekel KW - Obdachlos Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20140225-21297 ER - TY - THES A1 - Faschingeder, Kristian T1 - Das Unheimliche in der Stadt. Die urbane Vision Ludwig Hilberseimers N2 - Ausgangspunkt der Arbeit ist der Aspekt des Unheimlichen in jener Hochhausstadt, deren Entwurf Ludwig Hilberseimer 1924 zum ersten Mal publizierte und die später zum Synonym für die Aberrationen modernistischen Städtebaus wurde. Daraus geht die Forschungsfrage hervor, wie der Eindruck des Unheimlichen evoziert wird und an welchen Elementen des Entwurfs und/oder der Darstellung dieser festgemacht werden kann. Hier geht es nicht um eine Analyse der Intentionen des Autors der Hochhausstadt, der diese ja als Verbesserung zu den herrschenden Wohnverhältnissen anpries; stattdessen wird eine Reihe von unterschiedlichen interpretatorischen Ansätzen gewählt (von Nelson Goodmans Theorie der Notation über Norman Brysons visuelles Zeichensystem bis hin zu Adornos Negativer Dialektik; von der „Bildwissenschaft“ bis hin zur „visual theory“). In diesem Zusammenhang werden schließlich auch jene Divergenzen herausgearbeitet, die zwischen der Architektur der Moderne und der Kunst der Avantgarde herrschten. Da aufgrund der Frage nach der Bildwirkung der beiden Perspektiven der Hochhausstadt die Ästhetik des Erhabenen eine besondere Rolle spielt, reicht der Fokus der Arbeit bis in den kunst- und architekturtheoretischen Diskurs des 18. Jahrhundert zurück. Zuletzt mündet die Arbeit in eine Diskussion von Interpretation selbst und der Möglichkeit einer kritischen Architekturtheorie. N2 - The point of origin of the thesis is the issue of the uncanny in the Hochhausstadt, a project by the architect Ludwig Hilberseimer, which he published for the first time in 1924, and since then has turned into a symbol for the aberrations of modernist town planning. The research question then is, how this uncanniness is evoked and which are the elements within the drawing and/or the project, that can be made responsible for it. As such, this paper is far from an analysis that would attempt to retrace the intentions of the author of the Hochhausstadt, who himself praised his project as the solution to the most pressing problems of the contemporary city. Instead, a number of very different approaches is chosen for the interpretation (taking into account authors from the german speaking context and, most notably, from the anglo-saxon and french world). Finally, the discussion leads into a examination of interpretation itself and closes with a discussion of the possibility a critical theory of architecture. KW - Architekturtheorie KW - Moderne Architektur KW - Städtebau KW - Bildwissenschaft KW - Ästhetik KW - Ludwig Hilberseimer KW - Das Unheimliche Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20140226-21333 ER - TY - THES A1 - Nayono, Suwartanti T1 - Development of a Sustainability-based Sanitation Planning Tool (SusTA) for Developing Countries N2 - Background and Research Goal Despite all the efforts in the sanitation sector, it is acknowledged that the world is not on track to meet the MDG sanitation target to reduce the number of people without access to sanitation by 2015. Furthermore, a large number of existing sanitation facilities in developing countries is out of order. This leads to the conclusion that, besides technical failures, the planning process in the sanitation sector was ineffective. This ineffectiveness may be attributed to the lack of knowledge of the sanitation planners about the local conditions of the sanitation project. In addition, sustainability of a technology is often approached from a fragmented perspective that often leads to an unsustainable solution. The dissertation is conducted within the framework of the Integrated Water Resources Management (IWRM) Indonesia project. The goal of this work is to contribute to the development of a methodology of a planning tool for sustainable sanitation technology. The tool is designed for sanitation planners in developing countries, where a top-down planning approach is common practice. The proposed tool enables comprehensive sustainability assessments (using the Helmholtz Concept of Sustainability as reference), taking into account local conditions. State of the Science In the planning practice, many sanitation planning tools focus on technology selection. However, it has become evident that the selection criteria for sustainable technologies are not always considered in the tools’ framework. In other cases, when the criteria are provided by the tool, there is no clear indication of the conditions to be fulfilled in order to meet these criteria. Specifically, there is no reference to what is meant by sustainable technology in a particular context and how to comprehensively assess the sustainability of different technology options. Research Methodology Developing a planning tool is an empirical process, combining theory and practical experience. Hence, the development process of such a tool requires extensive observations, particularly on the interaction between stakeholders in the sanitation sector as well as between technology and its environment. For this purpose, a case study within the project area was carried out. Pucanganom, a village representing common strategic problems in developing countries (e.g. top-down planning approaches, lack of involvement of beneficiaries in the planning process, lack of sustainability assessments) was finally selected as the case study area. After the in-depth case study, an analytical generalisation was developed to enable the tool’s application to a broader context. Results The result of this research is a new tool – the Sustainability-based Sanitation Planning Tool (SusTA). SusTA enables comprehensive sustainability assessment in its five generic steps, namely: (1) analysis of stakeholders and sanitation policy in the region, (2) distance-to-target analysis on sanitation conditions in the region, (3) examination of physical and socio-economic conditions in the project area, (4) contextualisation of the technology assessment process in the project area, and (5) sustainability-oriented technology assessment at the project level. These steps are conducted at two levels of planning – the region and the project area – in order to identify the specific problems and interests which influence the selection of a sanitation system. Each planning step is equipped with tool elements (e.g. set of indicators, household questionnaires, technology assessment matrices) to support the analysis. From the development of SusTA, it can be concluded that four elements are required for an effective and widely applicable sanitation planning tool: sustainability concept, participatory approach, contextualisation framework and modification framework. SusTA provides both a theoretical and a practical basis for assessing the sustainability of sanitation technologies in developing countries. The tool’s main advantages for decision makers in these countries are: It is simple and transparent in its steps, does not require vast amounts of data and does not need a sophisticated computer program. KW - sanitation planning, sustainable technology, sustainability assessment KW - sanitation planning KW - sustainable technology KW - sustainability assessment Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20140619-22227 ER -