TY - JOUR A1 - Strukelj, A. T1 - Some Problems in Obtaining the Green's Function of the Layered Soil N2 - The frame of this paper is the development of methods and procedures for the description of the motion of an arbitrary shaped foundation. Since the infinite half-space cannot be properly described by a model of finite dimensions without violating the radiation condition, the basic problems are infinite dimensions of the half-space as well as its non-homogeneous nature. Consequently, an approach has been investigated to solve this problem indirectly by developing Green's function in which the non-homogeneity and the infiniteness of the half-space has been included. When the Green's function is known, the next step will be the evaluation of contact stresses acting between the foundation and the surface of the half-space through an integral equation. The equation should be solved in the area of the foundation using Green's function as the kernel. The derivation of three-dimensional Green's function for the homogeneous half-space (Kobayashi and Sasaki 1991) has been made using the potential method. Partial differential equations occurring in the problem have been made ordinary ones through the Hankel integral transform. The general idea for obtaining the three-dimensional Green's function for the layered half-space is similar. But in that case some additional phenomena may occur. One of them is the possibility of the appearance of Stonely surface waves propagating along the contact surfaces of layers. Their contribution to the final result is in most cases important enough that they should not be neglected. The main advantage of results presented in comparing to other obtained with numerical methods is their accuracy especially in the case of thin layers because all essential steps of Green's function evaluation except of the contour integration along the branch cut have been made analytically. On the other hand the disadvantage of this method is that the mathematical effort for obtaining the Green's function is increasing drastically with the increase of the number of layers. Future work will therefore be directed in simplifying of the above described process KW - Bodenmechanik KW - Geschichtetes Medium KW - Green-Funktion Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5388 ER - TY - JOUR A1 - Ganev, T. A1 - Marinov, M. T1 - Towards Optimal Designing of thin elastic Plates with a specific free Oscillations Frequency N2 - Thin elastic plates are the basic constructional elements and are very often subjected to dynamic effects especially in the machine-building structures. Their saving design of resonance conditions of operation is an extremely complicated task which cannot be solved analytically. In the present report an efficient and sufficiently general method for optimal design of thin plates is worked out on the basis of energy resonance method of Wilder, the method of the finite elements for dynamic research and the methods of parameter optimization. By means of these methods various limitations and requirements put by the designer to the plates can be taken into account. A programme module for numerical investigation of the weight variation of the plate depending on the taken variable of the designed thickness at different supporting conditions is developed. The reasons for the considerable quantity and quality difference between the obtained optimal designs are also analysed. KW - Platte KW - Optimierung KW - Freie Schwingung KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5375 ER - TY - JOUR A1 - Tolok, V. A. A1 - Tolok, A. V. A1 - Gomenyuk, S. I. T1 - The instrumental System of Mechanics Problems Analysis of the deformed Solid Body N2 - In the abstract proposed is the Instrumental System of mechanics problems analysis of the deformed solid body. It supplies the researcher with the possibility to describe the input data on the object under analyses and the problem scheme based upon the variational principles within one task. The particular feature of System is possibility to describe the information concerning the object of any geometrical shape and the computation sheme according to the program defined for purpose. The Methods allow to compute the tasks with indefinite functional and indefinite geometry of the object (or the set of objects). The System provides the possibility to compute the tasks with indefinite sheme based upon the Finite Element Method (FEM). The restrictions of the System usage are therefore determined by the restrictions of the FEM itself. It contrast to other known programms using FEM (ANSYS, LS-DYNA and etc) described system possesses more universality in defining input data and choosing computational scheme. Builtin is an original Subsytem of Numerical Result Analuses. It possesses the possibility to visualise all numerical results, build the epures of the unknown variables, etc. The Subsystem is approved while solving two- and three-dimensional problems of Elasticiti and Plasticity, under the conditions of Geometrical Unlinearity. Discused are Contact Problems of Statics and Dynamics. KW - Festkörpermechanik KW - Finite-Elemente-Methode Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5361 ER - TY - JOUR A1 - Kazakevitch, M. I. A1 - Volkova, Viktorija T1 - The exact Solution of the free pre-stressed Bar-Oscillations N2 - In this paper the results of the investigations of the free oscillations of the pre-stressed flexible structure elements are presented . Two cases of the central preliminary stress are investigated : without intermediate fastening of the tie to the flexible element and with the intermediate fastening in the middle of the element length. The given physical model can be applied to the flexible sloping shells and arches, membranes, large space antenna fields (besides flexible elements). The peculiarity of these systems is the possibility of the non-adjacent equilibrium form existence at the definite relations of the physical parameters . The transition from one stable equilibrium form to another, non-adjacent form, may be treated as jump. In this case they are called systems with buckling or the systems with two potential «gaps». These systems commenced the new section of the mathematical physics - the theory of chaos and strange attractors. The analysis of the solutions confirms the received for the first time by the author and given in effect of the oscillation period doubling of the system during the transition from the «small» oscillations relatively center to the >large< relatively all three equilibrium conditions. The character of the frequency (period) dependence on the free oscillation amplitudes of the non-linear system also confirms the received earlier result of the duality of the system behaviour : >small< oscillations possess the qualities of soft system; >large< oscillations possess the qualities of rigid system. The >small< oscillation natural frequency changing, depending on the oscillation amplitudes, is in the internal . Here the frequency takes zero value at the amplitude values Aa and Ad (or Aa and Ae ); the frequency takes maximum value at the amplitude value near point b .The >large< oscillation natural frequency changes in the interval . Here is also observed . The influence of the tie intermediate fastening doesn't introduce qualitative changes in the behaviour of the investigated system. It only increases ( four times ) the critical value of the preliminary tension force KW - Bauteil KW - Vorspannung KW - Freie Schwingung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5356 ER - TY - JOUR A1 - Zhak, S. V. A1 - Sidorenko, V. S. T1 - Optimized Models of Modes Choice for Displacement of technical Systems Objects N2 - The effectiveness of working processes accomplished by various technological machines to a large extend depends on working quality of supply, transporting and orientating mechanisms which are very often produced as positional hydro-mechanical systems. The choice of their best type and regimes of work requires construction and analysis of models of their optimum steering which are complicated by nonlinearness, multy-criterialness of problem and also by occasional outbreaks of parameters and moments of steering regime changing. It was developed the common structure of such systems allowing within common scheme to vary the complexity degree of PHMS and the methods of inhibitory efforts supplement. For some systems which are complicated in series (from two-measured linear system to nine-measured non-linear) puzzles of the most fast zero-ambit getting are solved and two-criterial problems are analyzed. (T-min-speed, Z(T)- accuracy). There are suggested the computing procedures of optimum PHMS synthesis. The effectiveness of accepted methods of solving is asserted by the analogy of the results of gradually complicated models investigation and by their good analogy with the natural experiment. It was exposed the sense of heuristic methods of improving of approximately optimum steering, their elaboration on the base of theoretical models. The basic methods of optimum PGMS construction were also nominated. KW - Modellierung KW - Optimierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5347 ER - TY - JOUR A1 - Skrinar, Matjaz T1 - Computation of Stresses and Settlements under an arbitrary Point in Homogenous, elastic, isotropic Half-Space, under the Load described by a uniform Load over a general quadrilateral N2 - The problem of the computation of stresses and settlements in the half-space under various types of loads is often presented in geotechnical engineering. In 1885 Boussinesq advanced theoretical expressions to determine stresses at a point within an ideal mass. His equation considers a point load on the surface of a semi-infinite, homogeneous, isotropic, weightless, elastic half-space. Newmark in 1942 performed the integration of Boussinesq's equations for the vertical stress under a corner of a rectangular area loaded with a uniform load. The problem of the determination of vertical stresses under a rectangular shaped footing has been satisfactorily solved with renewal integration of the Boussinesq's equation over the arbitrary rectangle on surface of the half-space, with a non-uniform load represented with piecewise linear interpolation functions. The problem of the determination of stresses in the case when the footing shape is an arbitrary quadrilateral however remains unsolved. The paper discusses an approach to the computation of vertical stresses and settlements in an arbitrary point of the half-space, loaded with a uniform load, which shape in the ground plan can be a general four noded form with straight edges. Since the form is transformed into a biunit square and all integrations are performed over this area, all solutions are valid also for an arbitrary triangle by the implementation of the degeneration rule. KW - Halbraum KW - Isotropie KW - Spannung KW - Setzung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5338 ER - TY - JOUR A1 - Kaplinski, O. T1 - Phenomenon of inhertia in the Production Systems reliability Analysis N2 - The paper analyses the influence of the effect of inertia on the reliability of production systems. Systems inertia represents the phenomenon of continuing work for some time after the breakdown of one of the former phases. In our considerations, inertia is treated as the time elapsed from the onset of breakdown till the system's inability to work. A special method had to be devised to investigate the effect of inertia in order to evaluate the reliability of production systems and to attempt algorithmization to control the reliability of production system by means of inertia or reserving. The method of reliability analysis is presented only in an inform aspect. The possibilities of increasing reliability of production systems are listed. A comparison of the redundancy method and inertia method is presented. The results of this comparison and simulated investigations of influence of inertia on reliability of system are essential scope of the paper. Selected conclusions are as follows: when inertia approaches the last phase in the system, its influence on the shape of the distribution of the system's ability increases; an increase in inertia causes an increase in the availability of the system which approaches a certain border value; dependence of the average of a system's disability on inertia has a saddle-like character whereas dependence of the number of breakdowns (stoppages) in the system has the nature of an S-curve. KW - Zuverlässigkeitstheorie KW - Trägheit Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5320 ER - TY - JOUR A1 - Lämmer, Lutz A1 - Burghardt, Michael A1 - Meißner, Udo F. T1 - Parallele Netzgenerierung N2 - Bei der Berechnung von statischen oder dynamischen Problemen mit Hilfe der Methode der Finiten Elemente ist eine Diskretisierung des zu berechnenden Gebietes notwendig. Bei einer sinnvollen Modellierung des Gebietes ist die Elementgröße meist nicht konstant, sondern ist an kritischen Stellen kleiner. Die Vorgaben hierfür können einerseits aus Erfahrungen des Anwenders, andererseits aus einer Fehlerabschätzung einer vorangegangenen FE-Berechnung resultieren [5]. Soll die FE-Berechnung auf einem Parallelrechner geschehen, ist eine Partitionierung des Gebietes, d.h. eine Zuordnung der Elemente zu den Prozessoren, notwendig. Bei dem hier beschriebenen Ansatz werden nun im Gegensatz zu den üblichen Verfahren erst die Eingangsdaten für den Netzgenerator umgewandelt und dann das Elementnetz direkt auf dem Parallelrecher gleichzeitig auf allen Prozessoren erzeugt. Eine Aufteilung der Elemente auf die Prozessoren entsteht als Nebenprodukt der Netzaufteilung. Die entstehenden Teilgebietsgrenzen werden geometrisch minimiert. Die Lastbalance der Netzaufteilung sowie der FE-Rechnung wird durch ein annähernd gleiche Anzahl der Elemente je Partition gewährleistet. Als Eingabedaten wird eine Beschreibung des Gebietes durch Polygonzüge, sowie einer Netzdichtefunktion, z.B. durch Punkte mit Angaben über die angestrebte Elementgröße, benötigt. KW - Finite-Elemente-Methode KW - Gittererzeugung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5315 ER - TY - JOUR A1 - Misztal, S. A1 - Misztal, G. T1 - Anwendung von Delta-Dirac-Funktion und Heviside-Funktion zur Berechnung der inneren Kräfte und Verschiebungen in gebogenen Balken N2 - Die d - Dirac - Funktion d(x-xi) und Heviside - Funktion wurden vor allem zur Beschreibung diskontinuierlicher Belastungsfunktionen von gebogenen Balken angewendet. Im Referat werden die mathematischen Operationen auf den erwähnten Funktionen dargestellt. Darüber hinaus wird die Möglichkeit eindeutiger Aufschreibung von belibigen Belestungsfunktionen vorgeschlagen, die fast alle Fälle der in der Ingenieurpraxis auftretenden Belastungen umfassen. Die vorgeschlagenen Lösungen geben die Möglichkeit leichter Aufschreibung im Form eines Algorithmus, das die Ausnutzung von Komputertechnik in statischen Berechnungen ermöglicht. Am Ende des Referates werden die Zahlebeispiele dargestellt, die die Möglichkeiten praktischer Anwendungen der besprochenen Funktionen darstellen. KW - Balken KW - Belastung KW - Mathematisches Modell KW - Computerunterstütztes Verfahren Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5308 ER - TY - JOUR A1 - Voronin, V. P. T1 - Renovation's peculiarities of industrial enterprises in conditions of economic selfsufficiency N2 - Probleme of recrienfation of building complex, to the sharp increase of share of reconstruction works, capital repair and modernisation of in-dustrial plants are concidered in this work. The conception of develop-ment and creation of unitified system of expluatation and renovation of industrial plants are worded out. This system is based on date-computer technology and taking into conciderations of real economic relations. KW - Bauwerk KW - Rekonstruktion KW - Wirtschaftlichkeit Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5296 ER -