TY - JOUR A1 - Piskunov, V. G. A1 - Marchuk, A. V. T1 - Model of stressed-strained State of Multilayer Masses with regard for Non-Ideal Contact of Layers N2 - Thus, mathematical model stressed- strained of a condition of layered masses is constructed. The model has high accuracy. It allows to simulate slippery contact of layers without friction. Thus not the order of permitting system of the equations is increased, and at its realization the method of fenite elements does not increase quantity of required degrees freedom. The differential operators included in system the equations are similar known in the classical theory of shells. It facilitates construction of a finite element. Presence in system of the differential equations of derivative of external forces allows to use her for the decision of contact problems with a stain of contact commensurable with thickness of a masses. KW - Geschichtetes Medium KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5427 ER - TY - JOUR A1 - Zhak, S. V. A1 - Sidorenko, V. S. T1 - Optimized Models of Modes Choice for Displacement of technical Systems Objects N2 - The effectiveness of working processes accomplished by various technological machines to a large extend depends on working quality of supply, transporting and orientating mechanisms which are very often produced as positional hydro-mechanical systems. The choice of their best type and regimes of work requires construction and analysis of models of their optimum steering which are complicated by nonlinearness, multy-criterialness of problem and also by occasional outbreaks of parameters and moments of steering regime changing. It was developed the common structure of such systems allowing within common scheme to vary the complexity degree of PHMS and the methods of inhibitory efforts supplement. For some systems which are complicated in series (from two-measured linear system to nine-measured non-linear) puzzles of the most fast zero-ambit getting are solved and two-criterial problems are analyzed. (T-min-speed, Z(T)- accuracy). There are suggested the computing procedures of optimum PHMS synthesis. The effectiveness of accepted methods of solving is asserted by the analogy of the results of gradually complicated models investigation and by their good analogy with the natural experiment. It was exposed the sense of heuristic methods of improving of approximately optimum steering, their elaboration on the base of theoretical models. The basic methods of optimum PGMS construction were also nominated. KW - Modellierung KW - Optimierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5347 ER - TY - JOUR A1 - Minch, M. J. A1 - Trochanowski, A. T1 - The numerical Modelling and Analysis of RC cracked Structures N2 - The purpose of this paper is to review model for finite element techniques for non-linear crack analysis of reinforced concrete beams and slabs. The non-linear behaviour of concrete and steel were described. Some calculations of >self-stress< for concrete and reinforced concrete beam was made. Current computational aspects are discussed. Several remarks for future studies are also given. The numerical model of the concrete and reinforced concrete was described. The paper shows the results of calculations on a reinforced concrete plane stress panel with cracks. The non-linear, numerical model of calculations of reinforced concrete was assumed. Using finite elements method some calculations were made. The results of calculations like displacements, stresses and cracking are shown on diagrams. They were compared with experimental results and other finding. Some conclusions about the described model and results of calculation are shown. KW - Tragwerk KW - Stahlbeton KW - Rissbildung KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5278 ER - TY - JOUR A1 - Kazakevitch, M. I. A1 - Kulyabko, V. V. A1 - Dubichvost, A. A. T1 - The discrete dynamic Models of the Interaction of complex - composite Structures with the dynamic Loads N2 - In the given paper the generalized formulation of the problem of computer modelling of the complex-composite structure interaction with different types of dynamic loads and effects is discussed. Here the analysis is given as for the usage of some universal computing systems for the solution of such problems. Also if is shown that the quantification of the dynamic models of the complex-composite systems with the variable structure, depending on the character and intensivity of the effects, is necessary. The different variants of the joint and the space structure element modelling are gested. It allows to consider the complex modes of the joint bending-torsional oscillations of such structures as bridges, towers, high-rise buildings. The peculiarities of the modelling and testing of some problems of the objects aerodynamics and the interaction of the frameworks constructions with shock and movable loads are considered. In this paper the examples of the complex-composite structure dynamic analysis are shown. It is achieved by means of some special methods of the input of the real inducements and loads of the exploitated analog-object into the computing model. The suggested models found a wide use both at the design of new structures and the dynamic monitoring of the exploitated structures. KW - Verbundtragwerk KW - Dynamische Belastung KW - Wechselwirkung KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5219 ER - TY - JOUR A1 - Fischer, A. A1 - Steinhage, V. T1 - Ein modellbasiertes Konzept zur städteplanerischen Kartierung durch digitale Bildanalyse N2 - There is an increasing need for 3D building extraction from aerial images for various applications such astown planning, environmental- and property-related studies. Aerial images usually reveal on one hand a certain amount of information not relevant for the given task of building extraction like vegetation, cars etc. On the other hand there is a loss of relevant information due to occlusions, low contrasts or disadvantageous perspectives. Therefore a promising concept for automated building reconstruction must incorporate a suffciantly complete model of the objects of interest. We propose a model-based approach to 3D building extraction from aerial images which reveals a tight coupling between a generic 3D object model and an explicit 2D image model. The generic object model employes domain specific volumetric primitives (i. e. building part models) and combination schemes. To cover the gap between 3D object models and 2D image data the image model is employed to predict the projective building appearences in aerial images. We present a strategy for a model-based building extraction based on the recognition-by-components principle and show first experimental results derived from international test sets KW - Stadtplanung KW - Kartierung KW - Bildanalyse KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4870 ER - TY - JOUR A1 - Rudnicki, Andrzej T1 - Investigation by Computer Simulation - some aspect of transportation service reliability in urban public transport N2 - Essence of service unreliability on account of irregularity has been given. The reasons of occurance of overcrowded vehicles have been listed. The factor of service unreliability on account of irregularity has been determined. It is probability of the event, that the passenger finds departing vehicle fully filled, i.e. when all places seating and standing are occupied or condition of the travel, which would be not acceptable for passenger. Large dispersion of headways (i.e. irregularity) increases probability of such situations. To calculate the mentioned factor, the computer simulation was used. Both, passenger arrivals and vehicle operation have been modelled as stochastic interacted processes. Distributions of headways and passenger arrivals have been fixed by statistical methods. The >maximal capacity< of a vehicle has been determined. The set of parameters values for simulation runs has been given. The transformed results of computer simulation are series of nomographs for determination of a factor value. They were prepared for many types of trams and city buses, but only one nomograph has been presented. Difficulties in verification of model were discussed. Recommendations for rational utilisation level of public transport means capacity in the condition of randomness of passenger arrivals and disturbances in vehicle operation have been proposed. The other possibilities of service unreliability have been mentioned. General conclusions have been given KW - Öffentlicher Personennahverkehr KW - Zuverlässigkeit KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4829 ER - TY - JOUR A1 - Dudek, Mariusz T1 - Modellierung der Verkehrsmittelwahl N2 - Die Zielstellung der Modal­Split­Betrachtungen läuft darauf hinaus, Entscheidungs-kriterien zu erarbeiten, nach denen die einzelnen Personen ihre Verkehrsmittel auswählen. In dieser Veröffentlichung wurden alle drei Gruppen der Modelle (klassische, verhaltensorientierte und der Analyse) der Verkehrsaufteilung kurz charakterisiert. Dann wurden vier ausgewählte Modelle genauer beschrieben. Zum Schluß wird das Modell der Verkehrsmittelwahl dargestellt , das für die Untersuchung der Verkehrsaufteilung in Krakau verwendet wurde . KW - Verkehrsmittelwahl KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4817 ER - TY - JOUR A1 - Rebolj, D. T1 - A Product Model of a Road N2 - Many errors and delays frequently appear when data is exchanged between particular tasks in the lifecycle of the road. Inter-task connections are therefore of great importance for the quality of the final product. The article describes a product model of a road wich is the kernel of an integrated information system intended to support all important stages of the road lifecycle: design, evaluation (through different analysis procedures), construction, and maintainance. Since particular tasks are often executed at different places and in different companies, the interconnections are supported by a special metafile which contains all specific data of the product model. The concept of the integrated system is object and component oriented. Additionally, existing conventional program packages are included to support some common tasks (methods). A conventional relational database system as well as an open spatial database system with the relevant GIS functionality are included to support the data structures of the model. KW - Straße KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4584 ER - TY - JOUR A1 - Wehner, R. A1 - Steinmann, Frank A1 - Hübler, Reinhard T1 - FLEXOB - Entwicklungstool für dynamische, modellbasierte CAD-Systeme N2 - Objektorientierte Modellierungstechniken werden gegenwärtig vor allem Entwicklern von CAD-Systemen angeboten. Sie erzeugen über die Schritte OO-Modellanalyse und OO-Softwaredesign OO-Programme, die mit ihrer Compilation das durch den Softwareingenieur gefundene Modell festschreiben. Generell, aber insbesondere im Bauwerksdesign, ist dieses Vorgehen unbefriedigend, da hier eine Normung von Modellen nicht gelingt, der Entwurfsprozeß vergleichsweise lang ist und eine Kooperation von Ingenieurgewerken mit verschiedenen Modelldomänen die Regel sind. Darüber hinaus weisen die Modelle in frühen Phasen ein hohes Maß an Unschärfe und Abstraktion auf. CAD-Tools, die diese Phasen unterstützen, benötigen deshalb: statt eines genormten Produktmodells ein einheitliches, kognitiv begründetes Modellstrukturierungsparadigma, für das mit der Objektorientierung eine mögliche Ausprägung gegeben ist, ein explizites, verfügbares Domänenmodell zur fortwährenden Interpretation von Bauwerksmodellen, deskriptive Elemente, die die Interpretation von Objekten und Attributen erleichtern, ein Konzept zur Behandlung von Unschärfe und Abstraktion. Hieraus ergeben sich für die Entwicklung von CAD-Systemen folgende Forderungen : Explizite Verfügbarkeit von Klassenobjekten und deren Erzeugung und Veränderung zur Laufzeit, Vererbung auf Klassen- und Instanzniveau, Erweiterte Attributkonzepte (Facetten), Unterstützung der Aggregation als einer wesentlichen Modellstrukturierungsrelation, Verfügbarkeit von OO-Schnittstellen zum Aufbau von CAD-Systemen aus Tools einerseits, sowie zur Trennung von Modellverwaltung und Modellrepräsentation andererseits. Als ein herausragendes Merkmal des Objektorientierten Paradigmas wird die Anwendungsnähe genannt, da Erscheinungen der behandelten Domäne sich analog in Modellen und Programmen wiederfinden (sollen). Unter der Grundannahme, daß dieses Paradigma auch durch den Anwender zur Erstellung seiner Modellwelten verwendet wird, will FLEXOB eine homogene Umgebung schaffen, die die Modellwelt des Softwareingenieurs zu Analysezwecken dem Anwender zur Verfügung stellt und die die Erweiterung dieser Modellwelt auf deskriptivem Niveau ermöglicht. Das Tool FLEXOB und einige wesentliche Implementationsdetails werden im Beitrag vorgestellt. Es handelt sich bei diesem Tools um eine C++ Klassenbibliothek, die entweder als Objektmodul oder als Windows-DLL verwendet werden kann. Aspekte des Nutzungsregimes solch flexibler Modellverwaltungen werden im Beitrag ebenfalls angespochen. KW - CAD KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4571 ER - TY - JOUR A1 - Steinmann, Frank A1 - Hübler, Reinhard T1 - Vorgehensmodelle als Basis der Gestaltung durchgaengiger CAD-Systeme N2 - Für die Gestaltung einer durchgängigen Unterstützung des Entwurfsprozesses stehen gegenwärtig deskriptive Modelle der Entwurfsobjekte im Mittelpunkt der Untersuchungen. Diese Modelle gestatten das Ableiten von Repräsentationen sowie eine Weitergabe von Entwurfsergebnissen. Pragmatische Gliederungen des Entwurfsprozesses unterteilen diesen nach organisatorischen und betriebswirtschaftlichen Aspekten (Planbarkeit und Abrechenbarkeit) in eine Sequenz von Entwurfsphasen (HOAI). Diese Gliederungen berücksichtigen nicht das WIE des eigentlichen modellkreierenden Schaffensprozesses. Für ein echtes CADesign bildet dessen Klärung jedoch die erforderliche Voraussetzung. Im Beitrag wird dazu von einem vereinheitlichten Set generischer Entwurfsaktionen ausgegangen. Auch dann, wenn die verschiedenen Entwurfsphasen und die Entwurfshandlungen der einzelnen Ingenieurgewerke mit spezifische Entwurfsmodellen verbunden werden, besteht damit eine Grundlage zur methodischen Fundierung entsprechender CAD-Tools. Die methodische Verfahrensweise ähnelt der, die in Form von Styleguides zur Gestaltung von 'Graphical User Interfaces' vorgeschlagen wird. Wesentliche praktische Benutzungen solche Basisaktivitäten ergeben sich für: die Systematisierung computergestützter Entwurfshandlungen, insbesondere durch Erweiterung des deskriptiven um ein operationales Modell sowie deren erweiterte Interpretierbarkeit die Erzeugung wissensbasierter Werkzeuge zur automatischen Modellgenerierung/-konfiguration die Implementation von leistungsfähigen UNDO- bzw. TMS-Mechanismen. KW - CAD KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4568 ER -