TY - THES A1 - Ehrhardt, Dirk T1 - ZUM EINFLUSS DER NACHBEHANDLUNG AUF DIE GEFÜGEAUSBILDUNG UND DEN FROST-TAUMITTELWIDERSTAND DER BETONRANDZONE N2 - Die Festigkeitsentwicklung des Zementbetons basiert auf der chemischen Reaktion des Zementes mit dem Anmachwasser. Durch Nachbehandlungsmaßnahmen muss dafür gesorgt werden, dass dem Zement genügend Wasser für seine Reaktion zur Verfügung steht, da sonst ein Beton mit minderer Qualität entsteht. Die vorliegende Arbeit behandelt die grundsätzlichen Fragen der Betonnachbehandlung bei Anwendung von Straßenbetonen. Im Speziellen wird die Frage des erforderlichen Nachbehandlungsbedarfs von hüttensandhaltigen Kompositzementen betrachtet. Die Wirkung der Nachbehandlung wird anhand des erreichten Frost-Tausalz-Widerstandes und der Gefügeausbildung in der unmittelbaren Betonrandzone bewertet. Der Fokus der Untersuchungen lag auf abgezogenen Betonoberflächen. Es wurde ein Modell zur Austrocknung des jungen Betons erarbeitet. Es konnte gezeigt werden, dass in einer frühen Austrocknung (Kapillarphase) keine kritische Austrocknung der Betonrandzone einsetzt, sondern der Beton annährend gleichmäßig über die Höhe austrocknet. Es wurde ein Nomogramm entwickelt, mit dem die Dauer der Kapillarphase in Abhängigkeit der Witterung für Straßenbetone abgeschätzt werden kann. Eine kritische Austrocknung der wichtigen Randzone setzt nach Ende der Kapillarphase ein. Für Betone unter Verwendung von Zementen mit langsamer Festigkeitsentwicklung ist die Austrocknung der Randzone nach Ende der Kapillarphase besonders ausgeprägt. Im Ergebnis zeigen diese Betone dann einen geringen Frost-Tausalz-Widerstand. Mit Zementen, die eine 2d-Zementdruckfestigkeit ≥ 23,0 N/mm² aufweisen, wurde unabhängig von der Zementart (CEM I oder CEM II/B-S) auch dann ein hoher Frost-Tausalz-Widerstand erreicht, wenn keine oder eine schlechtere Nachbehandlung angewendet wurde. Für die Praxis ergibt sich damit eine einfache Möglichkeit der Vorauswahl von geeigneten Zementen für den Verkehrsflächenbau. Betone, die unter Verwendung von Zementen mit langsamere Festigkeitsentwicklung hergestellt werden, erreichen einen hohen Frost-Tausalz-Widerstand nur mit einer geeigneten Nachbehandlung. Die Anwendung von flüssigen Nachbehandlungsmitteln (NBM gemäß TL NBM-StB) erreicht eine ähnliche Wirksamkeit wie eine 5 tägige Feuchtnachbehandlung. Voraussetzung für die Wirksamkeit der NBM ist, dass sie auf eine Betonoberfläche ohne sichtbaren Feuchtigkeitsfilm (feuchter Glanz) aufgesprüht werden. Besonders wichtig ist die Beachtung des richtigen Auftragszeitpunktes bei kühler Witterung, da hier aufgrund der verlangsamten Zementreaktion der Beton länger Anmachwasser abstößt. Ein zu früher Auftrag des Nachbehandlungsmittels führt zu einer Verschlechterung der Qualität der Betonrandzone. Durch Bereitstellung hydratationsabhängiger Transportkenngrößen (Feuchtetransport im Beton) konnten numerische Berechnungen zum Zusammenspiel zwischen der Austrocknung, der Nachbehandlung und der Gefügeentwicklung durchgeführt werden. Mit dem erstellten Berechnungsmodell wurden Parameterstudien durchgeführt. Die Berechnungen bestätigen die wesentlichen Erkenntnisse der Laboruntersuchungen. Darüber hinaus lässt sich mit dem Berechnungsmodell zeigen, dass gerade bei langsam reagierenden Zementen und kühler Witterung ohne eine Nachbehandlung eine sehr dünne Randzone (ca. 500 µm – 1000 µm) mit stark erhöhter Kapillarporosität entsteht. N2 - The hardening of cement concrete is based on the chemical reaction of cement and water. Therefore, the ensuring of sufficient amount of water in concrete is essential. All these measures are referred as curing of concrete. This dissertation provides a basic consideration of curing of concrete for concrete pavements. In this regard the using of cements with slow strength development, e.g. cements with blast furnace slag is the main topic. The effectiveness of curing was evaluated on the basis of the freeze-thaw de-icing resistance and the microstructure of hardened outer concrete surface. Concrete surfaces with textured mortar are on the focus. The results were used to develope a model of the drying of young concrete. It could be shown, that the outer concrete surface does not dry during the first drying phase (called capillary phase). Instead the concrete is drying evenly over the high of the concrete sample during the capillary drying phase. A fast drying of the outer concrete surface only takes place after the capillary drying phase. Based on all results a nomogram (for road concrete) was created for an estimation of the duration of the capillary drying phase. If there is no curing after the capillary drying phase the concrete with use of slowly reacting cement has a great risk for a harmful drying of outer concrete surface. In this case such a concrete shows a very poor freeze thaw de-icing resistance. By using cements with a 2 day-compressive strength ≥ 23,0 N/mm² a good freeze thaw de-icing resistance could assure, despite no or a poor curing was applied. This criterion can be used to estimate the usability of cements with granulated blast furnace slag when a great freeze thaw de-icing resistance is essential. There could also be used a cement with lower 2 day-compressive strength. In this case a good curing has to be assured. Spraying of liquid curing compounds according to TL NBM-StB is suitable for curing concrete pavements. The curing compound should not be sprayed on a concrete surface with any visible water film. The effectiveness of curing compounds is equal to a five days long wet curing in consideration of applying the curing compound at the right time. Otherwise there is some negative influence when the spraying of curing compounds starts too early. Consideration about the right application time of curing compounds is more important for low temperatures because the concrete bleeds much longer due to the slower cement reaction at low temperatures. It was possible to create a numerical model which accounts the interaction between drying, curing and development of microstructure by providing hydration dependent transport parameters (water transport in concrete). The model was used for a parameter study. It could be shown that the combination of cements with slow strength development and low ambient temperatures leads to a thin surface zone (500 µm – 1000 µm) with very high capillary porosity. KW - Beton KW - Zement KW - Nachbehandlung KW - Modellbildung KW - Nachbehandlungsmittel KW - Straßenbeton KW - Frost-Tausalz-Widerstand KW - curing compounds KW - concrete pavements Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171120-36889 ER - TY - THES A1 - Heidenreich, Manuel T1 - Untersuchungen zur Sauerstoffbereitstellung mit Perowskit- Keramik-Schüttungen in einem Festbett-Reaktor N2 - Diese Arbeit belegt, dass die Belastungen auf reversibel arbeitende keramische Materialien sehr gering ausfallen. Die regenerative Sauerstoffbereitstellung stellt damit grundsätzlich niedrigere Anforderungen an die keramischen Perowskit-Materialien zur Sauerstofferzeugung als die Membrantechnologie. Das Absinken der Diffusionskoeffizienten bei niedrigen Temperaturen ist deutlich weniger nachteilig als bei den Membranen die vergleichbare Materialien nutzen. Dies konnte gezeigt werde, indem mit der die O 2 -Entladetechnik und -Beladetechnik im Vergleich zur O 2 -Abtrennung durch keramische Membranen bei vergleichsweise niedrigen Temperaturen bereits große O 2 -Mengen erzeugt werden können. Infolge der niedrigen Temperaturen bestehen keine Probleme mit Reaktionen zwischen dem sauerstoffbereitstellenden Material und den Reaktorwerkstoffen. Dadurch gestaltet sich die Einbindung und Nutzung von Festbett-Schüttungen denkbar einfach. Im Vergleich dazu sind die Anbindung und der Betrieb von dünnen keramischen Membranen in einem Reaktor deutlich aufwendiger. Es ist weniger Peripherie und verfahrenstechnischer Aufwand zur Sauerstoffabtrennung durch reversibel arbeitende Materialien nötig als bei der kryogenen Luftzerlegung, der Druckwechseladsorption oder den Membrantechnologien. Die regenerative Sauerstoffbereitstellung kann sowohl bei neuen als auch bestehenden Anlagen, die Sauerstoff benötigen implementiert werden. Damit ist es möglich den Transport des Sauerstoffs entfallen zu lassen. Eine partielle Phasenumwandlung des BSCF8020 bei erhöhter Temperatur und hohem Sauerstoffangebot spielt für die regenerative Sauerstoffbereitstellung eine untergeordnete Rolle, da die nötigen Zieltemperaturen (450 ggf. bis 650 °C) zur O 2 -Beladung und -Entladung niedriger sind, als der Temperaturbereich in dem die Zersetzung auftreten kann (750 bis 800 °C). Des Weiteren ist die Zeitspanne (O 2 -Beladungsteilzyklus) in der das BSCF8020 ausreichend hohen Sauerstoffgehalten (p O2 > 10 -3 bar) ausgesetzt ist, zu kurz um diese Umwandlungen zu vollziehen. Der O 2 -Entladungsteilzyklus sorgt zusätzlich immer dafür, dass sich u. U. beginnende Zersetzung zurückbildet, da die kubische Phase in Richtung niedrigerer p O2 stabilisiert wird. Es konnte belegt werden, dass die elektronische Steuerung des zyklischen Sauerstoffausbaus und -einbaus beherrschbar ist. Der hohe Abtrenngrad der keramischen Materialien führt dazu, dass der Sauerstoff elektrolytisch rein zu Verfügung gestellt wird. Grundsätzlich sind weitere Forschungen zur Steigerung der Sauerstoffmengen, die pro eingesetzter Masseeinheit an Keramik gewonnen werden können, immer anzustreben, da damit u. U. der Materialeinsatz weiter gesenkt oder auch die energetischen Aufwendungen weiter reduziert werden können. Bei dem, für die multizyklischen Untersuchungen dieser Arbeit ausgewählten BSCF8020(SVT) hat die Cobalt-Komponente mit ca. 80 % den überwiegenden Kostenanteil am Sauerstoff bereitstellenden Material. BSCF-Keramiken mit höherem Eisen-Anteil sollten für multizyklische Anwendungen in Festbett-Reaktoren einer vertiefenden Charakterisierung unterzogen werden, um weitere geeignete Perowskite mit niedrigen Materialkosten zu erschließen. KW - Perowskit KW - Sauerstoff KW - Keramik KW - Festbett KW - Schüttung KW - BSCF KW - LSCF KW - SrMnO3 KW - CSMF KW - Dynamische Messungen Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171027-36077 ER - TY - THES A1 - Yuli, Nensi Golda T1 - The Spatial Concept at Moslem Settlements in Current Context of Modern Indonesia Using Phenomenology Method . Case Study: Pathok Negoro Area in Yogyakarta, Indonesia N2 - Settlement is human place to live and do various activities (Finch, 1980). Concept of settlement layout is closely associated with human and a set of thoughts and behaviors. In this case, idea of pattern of activities in a society that is core of a culture becomes main factor in process of formation of houses and environment in a settlement. Factors which affecting form (physical) of architecture in a settlement environment are socio-cultural, economic, and religious determinant factor that manifested architectural realization (Rapoport, 1969). Yogyakarta as the continuation of kingdom city in the Java Island finally exists as an Islamic kingdom that still remain to survive up to now. Impacts of this issue is appearance of various Moslem settlements to support typical character of an Islamic Kingdom. Mlangi is an area of oldest Moslem settlements in Yogyakarta has not been explored in details for progress especially in physical glasses recently. Everything basic group and individual who arrange houses and residences, starts from how it has spatial concept alone. Although concept is a very abstract thing to explain in details, but its existence can be detected by how they created their physical environment. This research conducted by these research questions: (1) What are spatial concepts owned by people in Mlangi and (2) How do spatial concepts owned by the people affect the settlements pattern? Process to search spatial concept owned by the people in Moslem residence, making Mlangi as study area, was approached by using phenomenological research method. The researcher have to self-involved directly in unstructured interviews, but remained in guideline framework of in interviews to make research process effective. Fistly, the researcher interviewed the key person, they are the head of Mlangi administration (pak Dukuh) in Mlangi and Sawahan. They were then give advices to who was capable person that could draw the spatial concept and had many story and knew the history of the settlements. Step by step of interview guided from one informant to next informant when the information had been told repeatedly. The next informant based on the last informant advice or who had close relationship with the last theme appeared. To complete the narration and draw the result of interview, researcher have to add additional information with photograph and descriptive picture that can be draw the settlement empirically. In process, 17 information units which found in field were consistent with sequence of interview events and flowing of theme to theme associated with Moslem residence of residence. Finally the interviews succeeded in abstracting 16 themes that may be classified into historic, socio-cultural, and spatial-concept dimensions in Mlangi. Process of analysis to find spatial concept owned by the people in Moslem settlements was carried out by dialogue of themes to find available substantive relationship. Four concepts successfully analyzed consist of concepts of personage, concept of religious implementation, concept of Jero-Jaba and concept of Interest. The four concepts are really associated with one and others in understanding how spatial concept owned by the people affects residence they occupy. Yet, concept of Jero-Jaba bases all concepts of people in Mlangi . This concept can be used to draw red yarn on how they utilize communal spaces in residence and layout rooms of their individual houses. This concept also eternalize residence patterns existing in Mlangi now where residence does not experience many changes from starting of this residence existence (from detection of generation currently still living), namely residence patterns concentrate on orientation to Masjid Pathok Negoro of Mlangi. This research was opening the potential research area, at least for the sociology, anthropology and demography research interest. So many unique character in Mlangi if looked at from how they maintain their spatial concept and manifested in their daily activities. How the people will concern only for the religious activities and the economic concern only for survival aspect in live. Keywords: spatial concept, moslem settlements, phenomenology method, Indonesia, KW - Siedlung KW - spatial concept KW - Muslim KW - moslem settlements KW - phenomenology method KW - Indonesia Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170419-31257 ER - TY - THES A1 - Podlaszewska, Rizky Suci Ammalia T1 - The Placemaking of Destination. Localization and Commoditization process of Urban Tourism. Study case Palembang Indonesia N2 - This research addresses the discourse of tourism as a tool for place-making of urban destination. Relevant to the study of place-making is the analysis of the commoditization and localization process dependent upon the appropriation of urban landscape and local cultures. In the research, localization is interpreted as the act of determining the attributes of locality, while commoditization is defined as the process by which local attributes that have commercial potential end up in becoming tourism commodity. Following this, the commoditization of intrinsic cultural value is disseminated within a branding strategy and intervention reflecting social and political relations. Therefore, the research suggests that tourism place-making has not only been constructed through the top-down regulatory body, but has been also generated through the attributes of its locality. By utilizing the critical and constructivist paradigm, the research depicts the conditions of the localization and commoditization process in establishing the base line of its realization within the symbolic economy. Thus, a qualitative case study approach was adopted. The study area of this dissertation is Palembang, as one of the capital cities in Indonesia advancing in its overall urban development. To investigate urban tourism as a tool for development strategy, it is useful to investigate the role of tourism which embodies (1) spatial transformation; how tourism gives significant impacts on urban form, and (2) the socio-cultural aspect; how neighbourhood is related to tourism industry. The findings suggest that tourism place-making involves the reciprocity of urban dynamics: cities take on tourism as a reference model of development, and tourist areas adopt the proliferation of cultural lifestyle to meet the industry’s demands. KW - Urbanistik Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171201-36995 ER - TY - THES A1 - Peters, Simone T1 - The Influence of Power Ultrasound on Setting and Strength Development of Cement Suspensions N2 - Ein aktuelles Thema in der Forschung der Betonindustrie ist die gezielte Steuerung des Erstarrens und der Entwicklung der (Früh)Festigkeit von Betonen und Mörteln. Aus ökonomischer Sicht sind außerdem die Reduktion der CO2-Emission und die Schonung von Ressourcen und Energie wichtige Forschungsschwerpunkte. Eine Möglichkeit zum Erreichen dieser Ziele ist es, die Reaktivität/Hydratation der silikatischen Klinkerphasen gezielt anzuregen. Neben den bereits bekannten Möglichkeiten der Hydratationsbeschleunigung (u.a. Wärmebehandlung, Zugabe von Salzen) bietet die Anwendung von Power-Ultraschall (PUS) eine weitere Alternative zur Beschleunigung der Zementhydratation. Da bis zum jetzigen Zeitpunkt noch keine Erfahrungen zum Einsatz von PUS in der Zementchemie vorliegen, sollen mit der vorliegenden Arbeit grundlegende Kenntnisse zum Einfluss von PUS auf das Fließ- und Erstarrungsverhalten von Zementsuspensionen erarbeitet werden. Dazu wurde die Arbeit in fünf Hauptuntersuchungsabschnitte aufgeteilt. Im ersten Teil wurden optimale PUS-Parameter wie Amplitude und Energieeintrag ermittelt, die eine effiziente Beschleunigung der Portlandzement(CEM I)hydratation bei kurzen Beschallzeiten und begrenzter Zementleimtemperaturerhöhung erlauben. Mit Hilfe unabhängiger Untersuchungsmethoden (Bestimmung des Erstarrungsbeginns, der Festigkeitsentwicklung, zerstörungsfreier Ultraschallprüfung, isothermer Wärmeflusskalorimetrie, hochauflösender Rasterelektronmikroskopie (REM) wurde die Wirkung von PUS auf den Hydratationsverlauf von CEM I-Suspensionen charakterisiert. Die Ergebnisse zeigen, dass die Behandlung von CEM I-Suspensionen mit PUS grundsätzlich ein beschleunigtes Erstarren und eine beschleunigte (Früh)Festigkeitsentwicklung hervorruft. Anhand von REM-Untersuchungen konnte eindeutig nachgewiesen werden, dass die Beschleunigung der CEM I-Hydratation mit einer beschleunigten Hydratation der Hauptklinkerphase Alit korreliert. Auf Grundlage dieser Erkenntnisse wurden die Ursachen der Aktivierung der Alithydratation untersucht. Dazu wurden Untersuchungen an Einzelsystemen des CEM I (silikatische Klinkerphase) durchgeführt. Es ist bekannt, das die Hydratation der Hauptklinkerphase Alit (in der reinen Form Tricalciumsilikat 3CaO*SiO2; C3S) durch Lösungs-/Fällungsreaktionen (Bildung von Calcium-Silikat-Hydrat Phasen, C-S-H Phasen) bestimmt wird. Mit Hilfe von Untersuchungen zur Auflösung (C3S) und Kristallbildung (C-S-H Phasen) in Lösungen und Suspensionen (Aufzeichnung der elektrischen Leitfähigkeit sowie Bestimmung der Ionenkonzentrationen der wässrigen Phase, REM-Charakterisierung der Präzipitate) wurde die Beeinflussung dieser durch eine PUS-Behandlung charakterisiert. Die Ergebnisse zeigen, dass in partikelfreien Lösungen (primäre Keimbildung) eine PUS-Behandlung keinen Einfluss auf die Kinetik der Kristallisation von C-S-H Phasen hervorruft. Das heißt, auch die durch PUS eingetragene Energie reicht offensichtlich nicht aus, um in Abwesenheit von Oberflächen die C-S-H Phasen Bildung zu beschleunigen. Das weist darauf hin, dass die Bildung von C-S-H Phasen nicht durch eine Beschleunigung von Ionen in der Lösung (erhöhte Diffusion durch Anwendung von PUS) hervorgerufen wird. Eine Beschleunigung des Kristallisationsprozesses (Keimbildung und Wachstum von C-S-H Phasen) durch PUS wird nur in Anwesenheit von Partikeln in der Lösung (Suspension) erzielt. Das belegen Ergebnisse, bei denen die Bildung erster C-S-H Phasen bei geringer Übersättigung (heterogene Keimbildung, in Anwesenheit von Oberflächen) erfolgt. Unter diesen Bedingungen konnte gezeigt werden, dass PUS innerhalb der ersten 30 Minuten der Hydratation eine erhöhte Fällung von ersten C-S-H Phasen bewirkt. Diese fungieren dann vermutlich während der Haupthydratation als Keim bzw. geeignete Oberfläche zum beschleunigten Aufwachsen von weiteren C-S-H Phasen. Weiterhin ist vorstellbar, dass (in Analogie zu anderen Bereichen der Sonochemie) PUS durch Kavitation Schockwellen hervorruft, welche Partikel und wässriges Medium beschleunigen und damit erhöhte Partikelbewegungen und -kollisionen induziert. Dies wiederum bewirkt, dass die anfänglich auf der C3S-Oberfläche gebildeten C-S-H Phasen teilweise wieder entfernt werden. Damit ist das Inlösunggehen von Ca- und Si-Ionen aus dem C3S weiterhin möglich. Um den genauen Mechanismus weiter zu charakterisieren sollten mit geeigneten Methoden weitere Untersuchungen durchgeführt werden. Im zweiten Teil der Arbeit wurde der Einfluss von PUS auf das Fließverhalten von CEM I-Suspensionen untersucht. Aus der Anwendung von PUS in anderen technischen Bereichen sind unter anderem Effekte wie das Entlüften, das Homogenisieren und das Dispergieren von Suspensionen und Emulsionen mittels PUS bekannt. Mit Hilfe der Bestimmung des Luftporengehaltes, Sedimentationsversuchen und cryo-SEM Untersuchungen wurde der Einfluss von PUS auf CEM I-Suspensionen charakterisiert. Die Ergebnisse belegen, dass durch PUS eine verbesserte Homogenität und Dispergierung der CEM I-Suspension erzielt wird. Damit wird für CEM I-Suspensionen unterschiedlichster w/z-Werte eine verbesserte Fließfähigkeit festgestellt. Ergebnisse der Bestimmung von Ausbreitmaßen und Trichterauslaufzeiten zeigen, dass PUS einen direkten Einfluss vor allem auf die Viskosität der CEM I-Suspensionen besitzt. Werden Fließmitteln (FM) der CEM I-Suspension zugegeben, wird nicht in jedem Fall eine verbesserte Fließfähigkeit festgestellt. Hier scheint unter bestimmten Voraussetzungen (w/z-Wert, FM-Gehalt, PUS) die Reaktion zwischen Aluminat- und Sulfatphase des Klinkers gestört. Zur eindeutigen Klärung dieses Sachverhaltes bedarf es jedoch weiterer quantitativer Untersuchungen zum Reaktionsumsatz. Im dritten Teil der Arbeit wurden die am CEM I gewonnenen Erkenntnisse zum Einfluss von PUS auf die Hydratation an Portland-Hüttensand(HÜS)-Zement-Systemen verifiziert. Dafür wurden auch in diesem Teil der Arbeit zunächst die optimalen PUS-Parameter festgelegt und der Einfluss auf das Erstarrung- und Erhärtungsverhalten dokumentiert. Untersuchungsmethoden sind unter anderem die Bestimmung des Erstarrungsbeginns und der (Früh)Festigkeitsentwicklung, Temperaturaufzeichnungen und isothermale Wärmeflusskalorimetrie sowie REM. Die Ergebnisse zeigen, dass auch die Reaktion von HÜS-Zementen durch PUS beschleunigt wird. Weiterführende Untersuchungen belegen, dass die erzielte Beschleunigung vorwiegend auf der Beschleunigung der Alitkomponente des CEM I beruht. Im Fokus der Teile vier und fünf dieser Arbeit stand die Anwendbarkeit der PUS-Technik unter praktischen Bedingungen. Zum einen wurde die Anwendbarkeit von PUS in fertig gemischten Mörteln beurteilt. Anhand des Vergleichs wichtiger Frisch- und Festmörteleigenschaften unterschiedlich hergestellter Mörtel (beschallt im Anschluss an konventionelle Mischtechnik, beschallt im Anschluss an Suspensionsmischtechnik mit anschließender Zumischung der Gesteinskörnung und nicht beschallt) wird gezeigt, dass im Fall von Mörteln mit hohem Leimanteil eine durch PUS induzierte beschleunigte Festigkeitsentwicklung auch mit herkömmlichen Mischabläufen (ohne aufwendige Umstellung des Mischprozesses) möglich ist. Abschließend wird untersucht, ob der Herstellungsprozess von Wandbauteilen im Fertigteilwerk durch den Einsatz von PUS optimiert werden kann und ob eine Einbindung der PUS-Technik in den Fertigungsprozess ohne größeren Aufwand möglich ist. Dazu wurden in einem ersten Schritt die Frisch- und Festbetoneigenschaften eines aktuell angewendeten selbstverdichtenden Betons im Labormaßstab (Mörtel) in Abhängigkeit einer PUS-Behandlung dokumentiert und mit der seiner unbeschallten Referenz verglichen. Aufgrund der durch PUS verursachten verbesserten Fließ- und Festigkeitseigenschaften kann die beschallte Mörtelrezeptur hinsichtlich Fließmittelgehalt und Dauer der Wärmebehandlung optimiert werden. Somit werden ca. 30 % der Fließmittelzugabe und 40 % der Dauer der Wärmebehandlung eigespart. Eine Einbindung der PUS-Technik in das betrachtete Fertigteilwerk ist nach Überprüfung der konstruktiven Gegebenheiten der Fertigungsstrukturen ohne größeren Aufwand möglich. KW - Cement KW - Power Ultrasound KW - Acceleration KW - Tricalcium silicate Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170210-27446 SN - ISBN 978-3-00-055602-9 ER - TY - THES A1 - Arboleda, Pablo T1 - Reckoning with Incompiuto Siciliano: Unfinished Public Works as Modern Ruins and All which it Entails N2 - Since the end of the 1950s, Italy has focused part of its modernization on the erection of public works. Due to corruption, mafia, and further malpractice, this form of development has occasionally failed, producing a high number of constructions that have remained unfinished for decades. In 2007, the group of artists Alterazioni Video constructed an informal survey in the form of an on-line tool open to public contributions, which revealed that there are 395 unfinished public works in Italy from which 156, approximately 39.5%, are located in Sicily alone. In view of such a statistic, Alterazioni Video opted to coin the term ‘Incompiuto Siciliano’ – literally ‘Sicilian Incompletion’ – to refer to unfinished public works as a formal architectural style. This re-interpretation, which aims to convey the recovered dignity of these ‘modern ruins’, considers unfinished public works a type of heritage with the potential to represent the entirety of Italian society. Furthermore, it goes as far as to say an unfinished public work is ‘Incompiuto Siciliano’ despite being located in another of the Italian regions. This doctoral dissertation embraces the artists’ argument to develop a complete study of Incompiuto Siciliano by embedding this architectural style/artistic project within the main debates on modern ruins at present. This is important because it is expected to contribute to the revalorization and eventual recommissioning of unfinished sites by validating Incompiuto Siciliano in the realm of academia. Furthermore, this work aspires to be a worthwhile source of information for future investigations dealing with cultural interpretations of incompletion in any other context – a not unreasonable goal considering how unfinished works are one of the key urban topics after the 2008 financial crisis. Hence, this doctoral dissertation uses Incompiuto Siciliano to discuss a different perspective in each of the five chapters and, though these can be read as independent contributions, the objective is that all chapters read together, form a clear, concise, continuous unit. And so it must be said this is not a dissertation about unfinished public works in Italy; this is a dissertation about Incompiuto Siciliano as an artistic response to unfinished public works in Italy – which clearly requires an interdisciplinary analysis involving Urban Studies, Cultural Geography, Contemporary Archaeology, Critical Heritage and Visual Arts. KW - Kulturerbe KW - incompiuto siciliano KW - unfinished public works KW - modern ruins KW - incompletion KW - heritage KW - aesthetics KW - art KW - culture Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170715-32656 ER - TY - THES A1 - Meyer-Kohlstock, Daniel T1 - Prospects for Biochar in a Bio-Waste Cascade N2 - In the early 2000s the pre-Columbian, anthropologically produced black soil in the Amazon basin, „Terra Preta de Índio“, received greater scientific attention. Compared to the surrounding poor soils, this very fertile anthrosol contains significantly higher levels of microorganisms and nutrients. The reason for this was determined to be the likewise high levels of charred biomass. This stable carbon, now called biochar, has since been intensively examined as an option to improve soil and to store carbon. Although the creation of Terra Preta was most likely based on a purposeful utilization of organic residues from households and gardens, biochar plays no role in the current recycling of bio-waste. However, the implementation of biochar could lead to many improvements. Results from agricultural research suggest that not only the yield capacity of soils can be increased but also the process performance of composting and biogas plants. The latter is especially relevant since currently about 40% of all collected bio-waste in Germany is recycled in an energy-material cascade consisting of anaerobic digestion and composting. The use of biochar in this cascade could then sequentially increase biogas yields, reduce greenhouse gas emissions, and improve compost quality. To realize the aforementioned advantages, the concept of biochar has to be integrated into the existing bio-waste cascade as practically as possible. This was done by the development of a theoretical scenario that allowed the analysis of energy and material flows to evaluate biochar’s recycling performance. Furthermore, the legal and economic framework were examined to assess the feasibility of the extended cascade and to suggest possible adjustments to the frameworks. KW - Kompost KW - Biogas KW - Pflanzenkohle Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171108-36310 ER - TY - THES A1 - Msekh, Mohammed Abdulrazzak T1 - Phase Field Modeling for Fracture with Applications to Homogeneous and Heterogeneous Materials N2 - The thesis presents an implementation including different applications of a variational-based approach for gradient type standard dissipative solids. Phase field model for brittle fracture is an application of the variational-based framework for gradient type solids. This model allows the prediction of different crack topologies and states. Of significant concern is the application of theoretical and numerical formulation of the phase field modeling into the commercial finite element software Abaqus in 2D and 3D. The fully coupled incremental variational formulation of phase field method is implemented by using the UEL and UMAT subroutines of Abaqus. The phase field method considerably reduces the implementation complexity of fracture problems as it removes the need for numerical tracking of discontinuities in the displacement field that are characteristic of discrete crack methods. This is accomplished by replacing the sharp discontinuities with a scalar damage phase field representing the diffuse crack topology wherein the amount of diffusion is controlled by a regularization parameter. The nonlinear coupled system consisting of the linear momentum equation and a diffusion type equation governing the phase field evolution is solved simultaneously via a Newton- Raphson approach. Post-processing of simulation results to be used as visualization module is performed via an additional UMAT subroutine implemented in the standard Abaqus viewer. In the same context, we propose a simple yet effective algorithm to initiate and propagate cracks in 2D geometries which is independent of both particular constitutive laws and specific element technology and dimension. It consists of a localization limiter in the form of the screened Poisson equation with, optionally, local mesh refinement. A staggered scheme for standard equilibrium and screened Cauchy equations is used. The remeshing part of the algorithm consists of a sequence of mesh subdivision and element erosion steps. Element subdivision is based on edge split operations using a given constitutive quantity (either damage or void fraction). Mesh smoothing makes use of edge contraction as function of a given constitutive quantity such as the principal stress or void fraction. To assess the robustness and accuracy of this algorithm, we use both quasi-brittle benchmarks and ductile tests. Furthermore, we introduce a computational approach regarding mechanical loading in microscale on an inelastically deforming composite material. The nanocomposites material of fully exfoliated clay/epoxy is shaped to predict macroscopic elastic and fracture related material parameters based on their fine–scale features. Two different configurations of polymer nanocomposites material (PNCs) have been studied. These configurations are fully bonded PNCs and PNCs with an interphase zone formation between the matrix and the clay reinforcement. The representative volume element of PNCs specimens with different clay weight contents, different aspect ratios, and different interphase zone thicknesses are generated by adopting Python scripting. Different constitutive models are employed for the matrix, the clay platelets, and the interphase zones. The brittle fracture behavior of the epoxy matrix and the interphase zones material are modeled using the phase field approach, whereas the stiff silicate clay platelets of the composite are designated as a linear elastic material. The comprehensive study investigates the elastic and fracture behavior of PNCs composites, in addition to predict Young’s modulus, tensile strength, fracture toughness, surface energy dissipation, and cracks surface area in the composite for different material parameters, geometry, and interphase zones properties and thicknesses. T2 - Phasenfeldmodellierung für Brüche mit Anwendungen auf homogene und heterogene Materialien KW - Finite-Elemente-Methode KW - Phase field model KW - Fracture KW - Abaqus KW - Finite Element Model Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170615-32291 ER - TY - THES A1 - Conrad, Lisa T1 - Organisation im soziotechnischen Gemenge - Mediale Umschichtungen durch die Einführung von SAP N2 - Der Alltag in Organisationen besteht vor allem aus den Medien und Technologien, mit denen die Koordination zwischen einzelnen Arbeitsabläufen hergestellt wird. Diese ethnografische Studie begleitet den Prozess der Einführung eines SAP-Systems in einem mittelständischen Unternehmen und zeigt, wie das bestehende Geflecht aus Praktiken und Technologien eine Neuanordnung erfährt. Dabei tritt das komplexe soziotechnische Gemenge zutage, auf dem Koordination und Organisation beruhen. Es geht um Hardware, ebenso wie Software, um mechanische und elektronische Medien, um Papiere, Drucker, Akten, Interfaces und Tastaturen, aber auch um die jahrzehntelang eingespielten Routinen und das Erfahrungswissen der Angestellten. KW - Organisationsforschung KW - Medienwissenschaft KW - Actor-Network-Theory KW - Ethnographie KW - Informationssystem KW - soziotechnisches Gemenge KW - Enterprise Resource Planning KW - ERP KW - SAP KW - infrastructure studies Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20180503-31079 SN - 978-3-8376-3784-7 N1 - Campuslizenz PB - transcript Verlag CY - Bielefeld ER - TY - THES A1 - Nariman, Nazim T1 - Numerical Methods for the Multi-Physical Analysis of Long Span Cable-Stayed Bridges N2 - The main categories of wind effects on long span bridge decks are buffeting, flutter, vortex-induced vibrations (VIV) which are often critical for the safety and serviceability of the structure. With the rapid increase of bridge spans, research on controlling wind-induced vibrations of long span bridges has been a problem of great concern.The developments of vibration control theories have led to the wide use of tuned mass dampers (TMDs) which has been proven to be effective for suppressing these vibrations both analytically and experimentally. Fire incidents are also of special interest in the stability and safety of long span bridges due to significant role of the complex phenomenon through triple interaction between the deck with the incoming wind flow and the thermal boundary of the surrounding air. This work begins with analyzing the buffeting response and flutter instability of three dimensional computational structural dynamics (CSD) models of a cable stayed bridge due to strong wind excitations using ABAQUS finite element commercial software. Optimization and global sensitivity analysis are utilized to target the vertical and torsional vibrations of the segmental deck through considering three aerodynamic parameters (wind attack angle, deck streamlined length and viscous damping of the stay cables). The numerical simulations results in conjunction with the frequency analysis results emphasized the existence of these vibrations and further theoretical studies are possible with a high level of accuracy. Model validation is performed by comparing the results of lift and moment coefficients between the created CSD models and two benchmarks from the literature (flat plate theory) and flat plate by (Xavier and co-authors) which resulted in very good agreements between them. Optimum values of the parameters have been identified. Global sensitivity analysis based on Monte Carlo sampling method was utilized to formulate the surrogate models and calculate the sensitivity indices. The rational effect and the role of each parameter on the aerodynamic stability of the structure were calculated and efficient insight has been constructed for the stability of the long span bridge. 2D computational fluid dynamics (CFD) models of the decks are created with the support of MATLAB codes to simulate and analyze the vortex shedding and VIV of the deck. Three aerodynamic parameters (wind speed, deck streamlined length and dynamic viscosity of the air) are dedicated to study their effects on the kinetic energy of the system and the vortices shapes and patterns. Two benchmarks from the literature (Von Karman) and (Dyrbye and Hansen) are used to validate the numerical simulations of the vortex shedding for the CFD models. A good consent between the results was detected. Latin hypercube experimental method is dedicated to generate the surrogate models for the kinetic energy of the system and the generated lift forces. Variance based sensitivity analysis is utilized to calculate the main sensitivity indices and the interaction orders for each parameter. The kinetic energy approach performed very well in revealing the rational effect and the role of each parameter in the generation of vortex shedding and predicting the early VIV and the critical wind speed. Both one-way fluid-structure interaction (one-way FSI) simulations and two-way fluid-structure interaction (two-way FSI) co-simulations for the 2D models of the deck are executed to calculate the shedding frequencies for the associated wind speeds in the lock-in region in addition to the lift and drag coefficients. Validation is executed with the results of (Simiu and Scanlan) and the results of flat plate theory compiled by (Munson and co-authors) respectively. High levels of agreements between all the results were detected. A decrease in the critical wind speed and the shedding frequencies considering (two-way FSI) was identified compared to those obtained in the (one-way FSI). The results from the (two-way FSI) approach predicted appreciable decrease in the lift and drag forces as well as prediction of earlier VIV for lower critical wind speeds and lock-in regions which exist at lower natural frequencies of the system. These conclusions help the designers to efficiently plan and consider for the design and safety of the long span bridge before and after construction. Multiple tuned mass dampers (MTMDs) system has been applied in the three dimensional CSD models of the cable stayed bridge to analyze their control efficiency in suppressing both wind -induced vertical and torsional vibrations of the deck by optimizing three design parameters (mass ratio, frequency ratio and damping ratio) for the (TMDs) supporting on actual field data and minimax optimization technique in addition to MATLAB codes and Fast Fourier Transform technique. The optimum values of each parameter were identified and validated with two benchmarks from the literature, first with (Wang and co-authors) and then with (Lin and co-authors). The validation procedure detected a good agreement between the results. Box-Behnken experimental method is dedicated to formulate the surrogate models to represent the control efficiency of the vertical and torsional vibrations. Sobol's sensitivity indices are calculated for the design parameters in addition to their interaction orders. The optimization results revealed better performance of the MTMDs in controlling both the vertical and the torsional vibrations for higher mode shapes. Furthermore, the calculated rational effect of each design parameter facilitates to increase the control efficiency of the MTMDs in conjunction with the support of the surrogate models which simplifies the process of analysis for vibration control to a great extent. A novel structural modification approach has been adopted to eliminate the early coupling between the bending and torsional mode shapes of the cable stayed bridge. Two lateral steel beams are added to the middle span of the structure. Frequency analysis is dedicated to obtain the natural frequencies of the first eight mode shapes of vibrations before and after the structural modification. Numerical simulations of wind excitations are conducted for the 3D model of the cable stayed bridge. Both vertical and torsional displacements are calculated at the mid span of the deck to analyze the bending and the torsional stiffness of the system before and after the structural modification. The results of the frequency analysis after applying lateral steel beams declared that the coupling between the vertical and torsional mode shapes of vibrations has been removed to larger natural frequencies magnitudes and higher rare critical wind speeds with a high factor of safety. Finally, thermal fluid-structure interaction (TFSI) and coupled thermal-stress analysis are utilized to identify the effects of transient and steady state heat-transfer on the VIV and fatigue of the deck due to fire incidents. Numerical simulations of TFSI models of the deck are dedicated to calculate the lift and drag forces in addition to determining the lock-in regions once using FSI models and another using TFSI models. Vorticity and thermal fields of three fire scenarios are simulated and analyzed. The benchmark of (Simiu and Scanlan) is used to validate the TFSI models, where a good agreement was manifested between the two results. Extended finite element method (XFEM) is adopted to create 3D models of the cable stayed bridge to simulate the fatigue of the deck considering three fire scenarios. The benchmark of (Choi and Shin) is used to validate the damaged models of the deck in which a good coincide was seen between them. The results revealed that the TFSI models and the coupled thermal-stress models are significant in detecting earlier vortex induced vibration and lock-in regions in addition to predicting damages and fatigue of the deck and identifying the role of wind-induced vibrations in speeding up the damage generation and the collapse of the structure in critical situations. KW - Stabilität KW - Brückenbau KW - Aerodynamic Stability KW - Vortex Induced Vibration KW - Fluid-Structure Interaction KW - Mass Tuned Damper KW - Thermal Fluid-Structure Interaction Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20171122-37105 ER -