TY - CHAP A1 - Kersten, Jens A1 - Rodehorst, Volker ED - Gürlebeck, Klaus ED - Lahmer, Tom T1 - TOWARDS STEREO VISION- AND LASER SCANNER-BASED UAS POSE ESTIMATION T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 20 - 22 2015, Bauhaus-University Weimar N2 - A central issue for the autonomous navigation of mobile robots is to map unknown environments while simultaneously estimating its position within this map. This chicken-eggproblem is known as simultaneous localization and mapping (SLAM). Asctec’s quadrotor Pelican is a powerful and flexible research UAS (unmanned aircraft system) which enables the development of new real-time on-board algorithms for SLAM as well as autonomous navigation. The relative UAS pose estimation for SLAM, usually based on low-cost sensors like inertial measurement units (IMU) and barometers, is known to be affected by high drift rates. In order to significantly reduce these effects, we incorporate additional independent pose estimation techniques using exteroceptive sensors. In this article we present first pose estimation results using a stereo camera setup as well as a laser range finder, individually. Even though these methods fail in few certain configurations we demonstrate their effectiveness and value for the reduction of IMU drift rates and give an outlook for further works towards SLAM. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Building Information Modeling KW - Computerunterstütztes Verfahren KW - Data, information and knowledge modeling in civil engineering; Function theoretic methods and PDE in engineering sciences; Mathematical methods for (robotics and) computer vision; Numerical modeling in engineering; Optimization in engineering applications Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-28072 SN - 1611-4086 ER - TY - CHAP A1 - Vasileva, Iuliia ED - Gürlebeck, Klaus ED - Lahmer, Tom T1 - THE PROBLEM OF PARTIAL REINFORCING AN INTERFACE CRACK EDGE BY A RIGID PATCH PLATE UNDER IN-PLANE AND ANTIPLANE LOADS T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 20 - 22 2015, Bauhaus-University Weimar N2 - The stress state of a piecewise-homogeneous elastic body, which has a semi-infinite crack along the interface, under in-plane and antiplane loads is considered. One of the crack edges is reinforced by a rigid patch plate on a finite interval adjacent to the crack tip. The crack edges are loaded with specified stresses. The body is stretched at infinity by specified stresses. External forces with a given principal vector and moment act on the patch plate. The problem reduces to a Riemann-Hilbert boundary-value matrix problem with a piecewise-constant coefficient for two complex potentials in the plane case and for one in the antiplane case. The complex potentials are found explicitly using a Gaussian hypergeometric function. The stress state of the body close to the ends of the patch plate, one of which is also simultaneously the crack tip, is investigated. Stress intensity factors near the singular points are determined. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Building Information Modeling KW - Computerunterstütztes Verfahren KW - Data, information and knowledge modeling in civil engineering; Function theoretic methods and PDE in engineering sciences; Mathematical methods for (robotics and) computer vision; Numerical modeling in engineering; Optimization in engineering applications Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-28242 SN - 1611-4086 ER - TY - CHAP A1 - Volkov, Andrey A1 - Kirschke, Heiko A1 - Chelyshkov, Pavel A1 - Sedov, Artem A1 - Lysenko, Denis ED - Gürlebeck, Klaus ED - Lahmer, Tom T1 - THE CRITERIA’S SET WITH INVARIANT DESIGN BUILDING ELEMENTS ON THE BASE OF THREE IMPUTATIONS: “CONVENIENCE”, “SAFETY” AND “ENERGY-EFFICIENCY” T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 20 - 22 2015, Bauhaus-University Weimar N2 - The paper deals with the formalization of the criteria for constructing building management systems. We consider three criteria - “convenience”, “safety” and “energyefficiency”. For each objective proposed method of calculation. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Building Information Modeling KW - Computerunterstütztes Verfahren KW - Data, information and knowledge modeling in civil engineering; Function theoretic methods and PDE in engineering sciences; Mathematical methods for (robotics and) computer vision; Numerical modeling in engineering; Optimization in engineering applications Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27956 SN - 1611-4086 ER - TY - CHAP A1 - Hamm, Matthias A1 - Beißert, Ulrike A1 - König, Markus ED - Gürlebeck, Klaus ED - Könke, Carsten T1 - SIMULATION-BASED OPTIMIZATION OF CONSTRUCTION SCHEDULES BY USING PARETO SIMULATED ANNEALING N2 - Within the scheduling of construction projects, different, partly conflicting objectives have to be considered. The specification of an efficient construction schedule is a challenging task, which leads to a NP-hard multi-criteria optimization problem. In the past decades, so-called metaheuristics have been developed for scheduling problems to find near-optimal solutions in reasonable time. This paper presents a Simulated Annealing concept to determine near-optimal construction schedules. Simulated Annealing is a well-known metaheuristic optimization approach for solving complex combinatorial problems. To enable dealing with several optimization objectives the Pareto optimization concept is applied. Thus, the optimization result is a set of Pareto-optimal schedules, which can be analyzed for selecting exactly one practicable and reasonable schedule. A flexible constraint-based simulation approach is used to generate possible neighboring solutions very quickly during the optimization process. The essential aspects of the developed Pareto Simulated Annealing concept are presented in detail. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Architektur KW - Computerunterstütztes Verfahren KW - Computer Science Models in Engineering; Multiscale and Multiphysical Models; Scientific Computing Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-28499 UR - http://euklid.bauing.uni-weimar.de/ikm2009/paper.html SN - 1611-4086 ER - TY - CHAP A1 - Almamou, Abd Albasset A1 - Gebhardt, Thomas A1 - Bock, Sebastian A1 - Hildebrand, Jörg A1 - Schwarz, Willfried ED - Gürlebeck, Klaus ED - Lahmer, Tom T1 - QUALITY CONTROL OF CONSTRUCTED MODELS USING 3D POINT CLOUD T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 20 - 22 2015, Bauhaus-University Weimar N2 - Over the last decade, the technology of constructing buildings has been dramatically developed especially with the huge growth of CAD tools that help in modeling buildings, bridges, roads and other construction objects. Often quality control and size accuracy in the factory or on construction site are based on manual measurements of discrete points. These measured points of the realized object or a part of it will be compared with the points of the corresponding CAD model to see whether and where the construction element fits into the respective CAD model. This process is very complicated and difficult even when using modern measuring technology. This is due to the complicated shape of the components, the large amount of manually detected measured data and the high cost of manual processing of measured values. However, by using a modern 3D scanner one gets information of the whole constructed object and one can make a complete comparison against the CAD model. It gives an idea about quality of objects on the whole. In this paper, we present a case study of controlling the quality of measurement during the constructing phase of a steel bridge by using 3D point cloud technology. Preliminary results show that an early detection of mismatching between real element and CAD model could save a lot of time, efforts and obviously expenses. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Building Information Modeling KW - Computerunterstütztes Verfahren KW - Data, information and knowledge modeling in civil engineering; Function theoretic methods and PDE in engineering sciences; Mathematical methods for (robotics and) computer vision; Numerical modeling in engineering; Optimization in engineering applications Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-27944 SN - 1611-4086 ER - TY - CHAP A1 - Seyler, Steve A1 - Schwarz, W. ED - Gürlebeck, Klaus ED - Könke, Carsten T1 - MODERN PHOTOGRAMMETRY IN CIVIL ENGINEERING - EXAMPLES FOR MONITORING AND EVALUATION N2 - Monitoring und Bewertung sind Hauptaufgaben im Management bzw. der Revitalisierung von Bauwerken. Unterschiedliche Verfahren können bei der Akquisition der erforderlichen geometrischen Information, wie z. B. Größe oder Verformung eines Gebäudes, eingesetzt werden. Da das Potenzial der digitalen Fotografie kontinuierlich wächst, stellt die Industriephotogrammetrie heute eine bedeutende Alternative zu den klassischen Verfahren wie Dehnmessstreifen oder anderen taktilen Sensoren dar. Moderne Industriephotogrammetrie erfasst die Bilder mittels digitaler Systeme. Dies bedeutet, dass die Information digitaler Bilder mit Hilfe der digitalen Bildverarbeitung untersucht werden muss, um die Bildkoordinaten der Messpunkte zu erhalten. Eine der Aufgaben der Bildverarbeitung für photogrammetrische Zwecke besteht somit darin, den Mittelpunkt von kreisförmigen Marken zu lokalisieren. Die modernen Operatoren liefern Subpixelgenauigkeit für die Koordinaten des Punktes. Das optische Messverfahren der Industriephotogrammetrie erfordert hinsichtlich der Hardware in erster Linie hochauflösende digitale Kameras. Dabei lassen sich die Kameras in Videokameras, HighSpeed-Kameras, intelligente Kameras sowie so genannte Consumer und Professionelle Kameras unterscheiden. Die geometrische Auflösung digitaler HighEnd-Kameras liegt heute bei über 10 Megapixel. In punkto Datentransfer zum Rechner sind verschiedene Standards am Markt verfügbar, z. B. USB2.0, GigE-Vision, CameraLink oder Firewire. Die Wahl des Standards hängt immer von der spezifischen Aufgabenstellung ab, da keine der Techniken eine führende Position einnimmt. Die moderne Photogrammetrie bietet viele neue Möglichkeiten für das Monitoring und die Bewertung von Bauwerken. Sie kann ein-, zwei-, drei- oder vierdimensionale Informationen liefern, falls erforderlich auch in Echtzeit. Als berührungsloses Messverfahren ist der Einsatz der Photogrammetrie noch möglich, wenn die taktilen Sensoren z. B. aufgrund ihres Platzbedarfes nicht mehr eingesetzt werden können. Hochauflösende Videokameras erlauben es, selbst dynamische Untersuchungen mit großer Präzision durchzuführen. KW - Architektur KW - CAD KW - Computerunterstütztes Verfahren Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170327-30192 UR - http://euklid.bauing.uni-weimar.de/ikm2006/index.php_lang=de&what=papers.html ER - TY - CHAP A1 - Heinrich, Timo ED - Gürlebeck, Klaus ED - Könke, Carsten T1 - KENNZEICHNUNGSBASIERTER ZUGRIFF VON PROZESSMODELLEN AUF OBJEKTBESTÄNDE DES BAUWESENS N2 - Für eine beherrschbare Koordination und Durchführung von Planungsaufgaben in Bauprojekten wird der Planungsprozess zunehmend in formalisierten Modellen – Prozessmodellen – beschrieben. Die Produktmodellforschung ihrerseits widmet sich der Speicherung von Planungsdaten in Form von objektorientierten Modellen im Rechner. Hauptaugenmerk sind dabei die Wahrung der Konsistenz und die Modellierung von Abhängigkeiten innerhalb dieses Planungsmaterials. Der Bezug zu den Akteuren der Planung wird nicht direkt hergestellt. Ein formal beschriebener Planungsprozesses kann in der Praxis noch nicht derart realisiert werden, dass ein Zugriff auf Einzelobjekte des Planungsprozesses gewährleistet ist. Bestehende Planungsunterstützungs- und Workflowmanagement-Systeme abstrahieren und ordnen das Planungsmaterial nach wie vor auf Dateiebene. Der vorliegende Artikel beschreibt eine Methode für die geeignete Verbindung von formalisierten Prozessmodellen in der Bauplanung mit den Einzelobjekten, die in den modellorientierten Objektmengen kodiert sind. Dabei wird die Zugehörigkeit bestimmter Objekte zu Plänen und Dokumenten (zum Zwecke des Datenaustauschs) nicht länger durch die physische Zuordnung zu Dateien festgelegt. Es wird ein formales Beschreibungsmittel vorgestellt, welches die entsprechende Teilmengenbildung aus der Gesamtheit der Planungsobjekte ermöglicht. Für die bisherigen Formen des Datenaustausches werden aus den Objektmodellen der Planung Teilmengen herausgelöst und physikalisch zwischen den Planern transportiert. Das neue Beschreibungsmittel hingegen erlaubt es, die Bildungsvorschrift für Objektteilmengen statt der Mengen selbst zwischen den Planern auszutauschen. Der Zugriff auf die konkreten Objekte findet dann direkt modellbasiert statt. KW - Architektur KW - CAD KW - Computerunterstütztes Verfahren Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170327-29669 UR - http://euklid.bauing.uni-weimar.de/ikm2006/index.php_lang=de&what=papers.html ER - TY - CHAP ED - Gürlebeck, Klaus ED - Lahmer, Tom T1 - International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 20 - 22 2015, Bauhaus-University Weimar T1 - Internationales Kolloquium über Anwendungen der Informatik und Mathematik in Architektur und Bauwesen : 20. bis 22.7. 2015, Bauhaus-Universität Weimar T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 20 - 22 2015, Bauhaus-University Weimar N2 - The 20th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering will be held at the Bauhaus University Weimar from 20th till 22nd July 2015. Architects, computer scientists, mathematicians, and engineers from all over the world will meet in Weimar for an interdisciplinary exchange of experiences, to report on their results in research, development and practice and to discuss. The conference covers a broad range of research areas: numerical analysis, function theoretic methods, partial differential equations, continuum mechanics, engineering applications, coupled problems, computer sciences, and related topics. Several plenary lectures in aforementioned areas will take place during the conference. We invite architects, engineers, designers, computer scientists, mathematicians, planners, project managers, and software developers from business, science and research to participate in the conference! KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren KW - Building Information Modeling KW - Optimization in engineering applications KW - Data, information and knowledge modeling in civil engineering KW - Function theoretic methods and PDE in engineering sciences KW - Mathematical methods for (robotics and) computer vision KW - Numerical modeling in engineering Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20150828-24515 SN - 1611-4086 ER - TY - CHAP ED - Gürlebeck, Klaus ED - Lahmer, Tom ED - Werner, Frank T1 - International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar T1 - Internationales Kolloquium über Anwendungen der Informatik und Mathematik in Architektur und Bauwesen : 04. bis 06.07. 2012, Bauhaus-Universität Weimar T2 - Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar N2 - The 19th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering will be held at the Bauhaus University Weimar from 4th till 6th July 2012. Architects, computer scientists, mathematicians, and engineers from all over the world will meet in Weimar for an interdisciplinary exchange of experiences, to report on their results in research, development and practice and to discuss. The conference covers a broad range of research areas: numerical analysis, function theoretic methods, partial differential equations, continuum mechanics, engineering applications, coupled problems, computer sciences, and related topics. Several plenary lectures in aforementioned areas will take place during the conference. We invite architects, engineers, designers, computer scientists, mathematicians, planners, project managers, and software developers from business, science and research to participate in the conference! KW - Angewandte Informatik KW - Angewandte Mathematik KW - Computerunterstütztes Verfahren Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20150916-24571 UR - http://euklid.bauing.uni-weimar.de/ikm2012 SN - 1611-4086 ER - TY - CHAP A1 - Lahmer, Tom ED - Gürlebeck, Klaus ED - Könke, Carsten T1 - HYDRO-MECHANICAL COUPLED FIELD SYSTEM IDENTIFICATION - APPLICATION TO WATER RESERVOIRS N2 - In this paper we present an inverse method which is capable of identifying system components in a hydro-mechanically coupled system, i.e. for fluid flow in porous media. As an example we regard water dams that were constructed more than hundred years ago but which are still in use. Over the time ageing processes have changed the condition of these dams. Within the dams fissures might have grown. The proposed method is designed to locate these fissures out of combined mechanical and hydraulic measurements. In a numerical example the fissures or damaged zones are described by a smeared crack model. The task is now to identify simultaneously the spatial distribution of Young’s modulus and the hydraulic permeability due to the fact, that in regions where damages are present, the mechanical stiffness of the system is reduced and the permeability increased. The inversion is shown to be an ill-posed problem. As a consequence regularizing methods have to be applied, where the nonlinear Landweber method (a gradient type method combined with a discrepancy principle) has proven to be an efficient choice. KW - Angewandte Informatik KW - Angewandte Mathematik KW - Architektur KW - Computerunterstütztes Verfahren KW - Computer Science Models in Engineering; Multiscale and Multiphysical Models; Scientific Computing Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170314-28650 UR - http://euklid.bauing.uni-weimar.de/ikm2009/paper.html SN - 1611-4086 ER -