TY - JOUR A1 - Zhuang, Xiaoying A1 - Huang, Runqiu A1 - Liang, Chao A1 - Rabczuk, Timon T1 - A coupled thermo-hydro-mechanical model of jointed hard rock for compressed air energy storage JF - Mathematical Problems in Engineering N2 - Renewable energy resources such as wind and solar are intermittent, which causes instability when being connected to utility grid of electricity. Compressed air energy storage (CAES) provides an economic and technical viable solution to this problem by utilizing subsurface rock cavern to store the electricity generated by renewable energy in the form of compressed air. Though CAES has been used for over three decades, it is only restricted to salt rock or aquifers for air tightness reason. In this paper, the technical feasibility of utilizing hard rock for CAES is investigated by using a coupled thermo-hydro-mechanical (THM) modelling of nonisothermal gas flow. Governing equations are derived from the rules of energy balance, mass balance, and static equilibrium. Cyclic volumetric mass source and heat source models are applied to simulate the gas injection and production. Evaluation is carried out for intact rock and rock with discrete crack, respectively. In both cases, the heat and pressure losses using air mass control and supplementary air injection are compared. KW - Energiespeicherung KW - Druckluft KW - Kaverne KW - Modellierung Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170428-31726 ER - TY - JOUR A1 - Zhak, S. V. A1 - Sidorenko, V. S. T1 - Optimized Models of Modes Choice for Displacement of technical Systems Objects N2 - The effectiveness of working processes accomplished by various technological machines to a large extend depends on working quality of supply, transporting and orientating mechanisms which are very often produced as positional hydro-mechanical systems. The choice of their best type and regimes of work requires construction and analysis of models of their optimum steering which are complicated by nonlinearness, multy-criterialness of problem and also by occasional outbreaks of parameters and moments of steering regime changing. It was developed the common structure of such systems allowing within common scheme to vary the complexity degree of PHMS and the methods of inhibitory efforts supplement. For some systems which are complicated in series (from two-measured linear system to nine-measured non-linear) puzzles of the most fast zero-ambit getting are solved and two-criterial problems are analyzed. (T-min-speed, Z(T)- accuracy). There are suggested the computing procedures of optimum PHMS synthesis. The effectiveness of accepted methods of solving is asserted by the analogy of the results of gradually complicated models investigation and by their good analogy with the natural experiment. It was exposed the sense of heuristic methods of improving of approximately optimum steering, their elaboration on the base of theoretical models. The basic methods of optimum PGMS construction were also nominated. KW - Modellierung KW - Optimierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5347 ER - TY - JOUR A1 - Wehner, R. A1 - Steinmann, Frank A1 - Hübler, Reinhard T1 - FLEXOB - Entwicklungstool für dynamische, modellbasierte CAD-Systeme N2 - Objektorientierte Modellierungstechniken werden gegenwärtig vor allem Entwicklern von CAD-Systemen angeboten. Sie erzeugen über die Schritte OO-Modellanalyse und OO-Softwaredesign OO-Programme, die mit ihrer Compilation das durch den Softwareingenieur gefundene Modell festschreiben. Generell, aber insbesondere im Bauwerksdesign, ist dieses Vorgehen unbefriedigend, da hier eine Normung von Modellen nicht gelingt, der Entwurfsprozeß vergleichsweise lang ist und eine Kooperation von Ingenieurgewerken mit verschiedenen Modelldomänen die Regel sind. Darüber hinaus weisen die Modelle in frühen Phasen ein hohes Maß an Unschärfe und Abstraktion auf. CAD-Tools, die diese Phasen unterstützen, benötigen deshalb: statt eines genormten Produktmodells ein einheitliches, kognitiv begründetes Modellstrukturierungsparadigma, für das mit der Objektorientierung eine mögliche Ausprägung gegeben ist, ein explizites, verfügbares Domänenmodell zur fortwährenden Interpretation von Bauwerksmodellen, deskriptive Elemente, die die Interpretation von Objekten und Attributen erleichtern, ein Konzept zur Behandlung von Unschärfe und Abstraktion. Hieraus ergeben sich für die Entwicklung von CAD-Systemen folgende Forderungen : Explizite Verfügbarkeit von Klassenobjekten und deren Erzeugung und Veränderung zur Laufzeit, Vererbung auf Klassen- und Instanzniveau, Erweiterte Attributkonzepte (Facetten), Unterstützung der Aggregation als einer wesentlichen Modellstrukturierungsrelation, Verfügbarkeit von OO-Schnittstellen zum Aufbau von CAD-Systemen aus Tools einerseits, sowie zur Trennung von Modellverwaltung und Modellrepräsentation andererseits. Als ein herausragendes Merkmal des Objektorientierten Paradigmas wird die Anwendungsnähe genannt, da Erscheinungen der behandelten Domäne sich analog in Modellen und Programmen wiederfinden (sollen). Unter der Grundannahme, daß dieses Paradigma auch durch den Anwender zur Erstellung seiner Modellwelten verwendet wird, will FLEXOB eine homogene Umgebung schaffen, die die Modellwelt des Softwareingenieurs zu Analysezwecken dem Anwender zur Verfügung stellt und die die Erweiterung dieser Modellwelt auf deskriptivem Niveau ermöglicht. Das Tool FLEXOB und einige wesentliche Implementationsdetails werden im Beitrag vorgestellt. Es handelt sich bei diesem Tools um eine C++ Klassenbibliothek, die entweder als Objektmodul oder als Windows-DLL verwendet werden kann. Aspekte des Nutzungsregimes solch flexibler Modellverwaltungen werden im Beitrag ebenfalls angespochen. KW - CAD KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4571 ER - TY - JOUR A1 - Steinmann, Frank A1 - Hübler, Reinhard T1 - Vorgehensmodelle als Basis der Gestaltung durchgaengiger CAD-Systeme N2 - Für die Gestaltung einer durchgängigen Unterstützung des Entwurfsprozesses stehen gegenwärtig deskriptive Modelle der Entwurfsobjekte im Mittelpunkt der Untersuchungen. Diese Modelle gestatten das Ableiten von Repräsentationen sowie eine Weitergabe von Entwurfsergebnissen. Pragmatische Gliederungen des Entwurfsprozesses unterteilen diesen nach organisatorischen und betriebswirtschaftlichen Aspekten (Planbarkeit und Abrechenbarkeit) in eine Sequenz von Entwurfsphasen (HOAI). Diese Gliederungen berücksichtigen nicht das WIE des eigentlichen modellkreierenden Schaffensprozesses. Für ein echtes CADesign bildet dessen Klärung jedoch die erforderliche Voraussetzung. Im Beitrag wird dazu von einem vereinheitlichten Set generischer Entwurfsaktionen ausgegangen. Auch dann, wenn die verschiedenen Entwurfsphasen und die Entwurfshandlungen der einzelnen Ingenieurgewerke mit spezifische Entwurfsmodellen verbunden werden, besteht damit eine Grundlage zur methodischen Fundierung entsprechender CAD-Tools. Die methodische Verfahrensweise ähnelt der, die in Form von Styleguides zur Gestaltung von 'Graphical User Interfaces' vorgeschlagen wird. Wesentliche praktische Benutzungen solche Basisaktivitäten ergeben sich für: die Systematisierung computergestützter Entwurfshandlungen, insbesondere durch Erweiterung des deskriptiven um ein operationales Modell sowie deren erweiterte Interpretierbarkeit die Erzeugung wissensbasierter Werkzeuge zur automatischen Modellgenerierung/-konfiguration die Implementation von leistungsfähigen UNDO- bzw. TMS-Mechanismen. KW - CAD KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4568 ER - TY - JOUR A1 - Staub-French, Sheryl T1 - Feature-based Product Modeling for Building Construction N2 - Current building product models explicitly represent components, attributes of components, and relationships between components. These designer-focused product models, however, do not represent many of the design conditions that are important for construction, such as component similarity, uniformity, and penetrations. Current design and construction tools offer limited support for detecting these construction-specific design conditions. This paper describes the ontology we developed using the manufacturing concept of features to represent the design conditions that are important for construction. The feature ontology provides the blueprint for the additions and changes needed to transform a standard product model into a constructionspecific product model. The ontology formalizes three classes of features, defines the attributes and functions of each feature type, and represents the relationships between features explicitly. The descriptive semantics of the ontology allows practitioners to represent their varied preferences for naming features, specifying features that result from component intersections and the similarity of components, and grouping features that affect a specific construction domain. A software prototype that implements the ontology enables practitioners to transform designer-focused product models into feature-based product models that represent the construction perspective. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Baukonstruktion KW - Modellierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2331 ER - TY - JOUR A1 - Rudnicki, Andrzej T1 - Investigation by Computer Simulation - some aspect of transportation service reliability in urban public transport N2 - Essence of service unreliability on account of irregularity has been given. The reasons of occurance of overcrowded vehicles have been listed. The factor of service unreliability on account of irregularity has been determined. It is probability of the event, that the passenger finds departing vehicle fully filled, i.e. when all places seating and standing are occupied or condition of the travel, which would be not acceptable for passenger. Large dispersion of headways (i.e. irregularity) increases probability of such situations. To calculate the mentioned factor, the computer simulation was used. Both, passenger arrivals and vehicle operation have been modelled as stochastic interacted processes. Distributions of headways and passenger arrivals have been fixed by statistical methods. The >maximal capacity< of a vehicle has been determined. The set of parameters values for simulation runs has been given. The transformed results of computer simulation are series of nomographs for determination of a factor value. They were prepared for many types of trams and city buses, but only one nomograph has been presented. Difficulties in verification of model were discussed. Recommendations for rational utilisation level of public transport means capacity in the condition of randomness of passenger arrivals and disturbances in vehicle operation have been proposed. The other possibilities of service unreliability have been mentioned. General conclusions have been given KW - Öffentlicher Personennahverkehr KW - Zuverlässigkeit KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4829 ER - TY - JOUR A1 - Rebolj, D. T1 - A Product Model of a Road N2 - Many errors and delays frequently appear when data is exchanged between particular tasks in the lifecycle of the road. Inter-task connections are therefore of great importance for the quality of the final product. The article describes a product model of a road wich is the kernel of an integrated information system intended to support all important stages of the road lifecycle: design, evaluation (through different analysis procedures), construction, and maintainance. Since particular tasks are often executed at different places and in different companies, the interconnections are supported by a special metafile which contains all specific data of the product model. The concept of the integrated system is object and component oriented. Additionally, existing conventional program packages are included to support some common tasks (methods). A conventional relational database system as well as an open spatial database system with the relevant GIS functionality are included to support the data structures of the model. KW - Straße KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-4584 ER - TY - JOUR A1 - Piskunov, V. G. A1 - Marchuk, A. V. T1 - Model of stressed-strained State of Multilayer Masses with regard for Non-Ideal Contact of Layers N2 - Thus, mathematical model stressed- strained of a condition of layered masses is constructed. The model has high accuracy. It allows to simulate slippery contact of layers without friction. Thus not the order of permitting system of the equations is increased, and at its realization the method of fenite elements does not increase quantity of required degrees freedom. The differential operators included in system the equations are similar known in the classical theory of shells. It facilitates construction of a finite element. Presence in system of the differential equations of derivative of external forces allows to use her for the decision of contact problems with a stain of contact commensurable with thickness of a masses. KW - Geschichtetes Medium KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5427 ER - TY - JOUR A1 - Minch, M. J. A1 - Trochanowski, A. T1 - The numerical Modelling and Analysis of RC cracked Structures N2 - The purpose of this paper is to review model for finite element techniques for non-linear crack analysis of reinforced concrete beams and slabs. The non-linear behaviour of concrete and steel were described. Some calculations of >self-stress< for concrete and reinforced concrete beam was made. Current computational aspects are discussed. Several remarks for future studies are also given. The numerical model of the concrete and reinforced concrete was described. The paper shows the results of calculations on a reinforced concrete plane stress panel with cracks. The non-linear, numerical model of calculations of reinforced concrete was assumed. Using finite elements method some calculations were made. The results of calculations like displacements, stresses and cracking are shown on diagrams. They were compared with experimental results and other finding. Some conclusions about the described model and results of calculation are shown. KW - Tragwerk KW - Stahlbeton KW - Rissbildung KW - Modellierung Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-5278 ER - TY - JOUR A1 - Legatiuk, Dmitrii A1 - Weisz-Patrault, Daniel T1 - Coupling of Complex Function Theory and Finite Element Method for Crack Propagation Through Energetic Formulation: Conformal Mapping Approach and Reduction to a Riemann–Hilbert Problem JF - Computational Methods and Function Theory N2 - In this paper we present a theoretical background for a coupled analytical–numerical approach to model a crack propagation process in two-dimensional bounded domains. The goal of the coupled analytical–numerical approach is to obtain the correct solution behaviour near the crack tip by help of the analytical solution constructed by using tools of complex function theory and couple it continuously with the finite element solution in the region far from the singularity. In this way, crack propagation could be modelled without using remeshing. Possible directions of crack growth can be calculated through the minimization of the total energy composed of the potential energy and the dissipated energy based on the energy release rate. Within this setting, an analytical solution of a mixed boundary value problem based on complex analysis and conformal mapping techniques is presented in a circular region containing an arbitrary crack path. More precisely, the linear elastic problem is transformed into a Riemann–Hilbert problem in the unit disk for holomorphic functions. Utilising advantages of the analytical solution in the region near the crack tip, the total energy could be evaluated within short computation times for various crack kink angles and lengths leading to a potentially efficient way of computing the minimization procedure. To this end, the paper presents a general strategy of the new coupled approach for crack propagation modelling. Additionally, we also discuss obstacles in the way of practical realisation of this strategy. KW - Angewandte Mathematik KW - Finite-Elemente-Methode KW - Rissausbreitung KW - Modellierung KW - Bruchmechanik KW - fracture mechanics KW - crack propagation KW - coupling KW - energetic approach Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20210805-44763 UR - https://link.springer.com/article/10.1007/s40315-021-00403-7 VL - 2021 SP - 1 EP - 23 PB - Springer CY - Heidelberg ER -