TY - THES A1 - Flohr, Alexander T1 - Der Einfluss von Polymermodifikationen, unterschiedlichen Gesteinskörnungen und Gesteinskörnungssubstitutionsmaterial auf das Verformungs- und Bruchverhalten von Beton N2 - In dieser Arbeit werden die Ergebnisse von experimentellen Untersuchungen an unbewehrten und bewehrten modifizierten Betonen unter monoton steigender Belastung bis zum Bruch, einfacher Kurzzeitbelastung im Grenzbereich der Tragfähigkeit und mehrfach wiederholter Belastung mit kontinuierlicher Be- und Entlastungsgeschwindigkeit vorgestellt und ausgewertet. Für die Modifizierung der Betone wurden zwei grundsätzliche Vorgehens¬weisen angewendet: die Variation der Gesteinskörnung und die Modifizierung der Bindemittelphase mit thermoplastischen Polymeren. Die Auswirkungen der Modifikationen auf die Festigkeitseigenschaften und das Formänderungsverhalten des Betons bei Kurzzeitbelastung waren dabei von besonderem Interesse. Die beobachteten Veränderungen der Festbetoneigenschaften sowie der nichtlineare Zu-sammenhang zwischen den elastischen und nichtelastischen Verformungsanteilen signali-sieren, dass derartige Modifizierungen das Verformungs- und Bruchverhalten von Beton sig-nifikant beeinflussen und somit beim Nachweis der Tragfähigkeit und Gebrauchstauglichkeit berücksichtigt werden müssen. Neben der Evaluierung des beanspruchungsabhängigen Formänderungsverhaltens werden die etablierten Ansätze zur Beschreibung der Gefügezu-standsbereiche bei Druckbelastung weiter entwickelt, so dass die Übergänge zwischen den Bereichen exakt ermittelt und die Ausprägung der Bereiche quantifiziert werden können. Damit ist ein genauerer Vergleich der durch die Modifizierungen hervorgerufenen Verände-rungen möglich. N2 - The results of experimental investigations of unreinforced and reinforced modified concrete under monotonically increasing load until fracture, simple short-term load at the limit of capa-city and repeated load with continuous loading and release rate are introduced in the pre-sented thesis. The modification of the concretes was approached in two ways: the variation of the aggregates and the modification of the binder phase with thermoplastic polymers. Of particular interest were the effects of the modifications on the strength properties and the deformation behavior under short-term load. The observed changes in the hardened concrete properties and the non-linear relation be-tween the elastic and inelastic proportions of deformation indicate that such modifications affect the deformation and fracture behavior of concrete significantly. Therefore they have to be accounted for the analysis of capacity and suitability. In addition to the evaluation of the load-dependent deformation behavior, the established approaches to describe the structural state areas are developed further. Therewith, the transitions between the areas can be de-termined accurately and the dimension of the areas can be quantified. As a result the chang-es caused by modifications could be compared more precisely. KW - Beton KW - Polymermodifizierter Beton KW - Concrete KW - Gesteinskörnung KW - Gesteinskörnungssubstitutionsmaterial KW - Lastverformungsverhalten KW - Bruchverhalten KW - Druckbelastung KW - Zugbelastung KW - Biegezugbelastung KW - Polymermodified Cement Concrete KW - aggregates KW - deformation behavior Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20130806-20035 ER - TY - THES A1 - Hanna, John T1 - Computational Fracture Modeling and Design of Encapsulation-Based Self-Healing Concrete Using XFEM and Cohesive Surface Technique N2 - Encapsulation-based self-healing concrete (SHC) is the most promising technique for providing a self-healing mechanism to concrete. This is due to its capacity to heal fractures effectively without human interventions, extending the operational life and lowering maintenance costs. The healing mechanism is created by embedding capsules containing the healing agent inside the concrete. The healing agent will be released once the capsules are fractured and the healing occurs in the vicinity of the damaged part. The healing efficiency of the SHC is still not clear and depends on several factors; in the case of microcapsules SHC the fracture of microcapsules is the most important aspect to release the healing agents and hence heal the cracks. This study contributes to verifying the healing efficiency of SHC and the fracture mechanism of the microcapsules. Extended finite element method (XFEM) is a flexible, and powerful discrete crack method that allows crack propagation without the requirement for re-meshing and has been shown high accuracy for modeling fracture in concrete. In this thesis, a computational fracture modeling approach of Encapsulation-based SHC is proposed based on the XFEM and cohesive surface technique (CS) to study the healing efficiency and the potential of fracture and debonding of the microcapsules or the solidified healing agents from the concrete matrix as well. The concrete matrix and a microcapsule shell both are modeled by the XFEM and combined together by CS. The effects of the healed-crack length, the interfacial fracture properties, and microcapsule size on the load carrying capability and fracture pattern of the SHC have been studied. The obtained results are compared to those obtained from the zero thickness cohesive element approach to demonstrate the significant accuracy and the validity of the proposed simulation. The present fracture simulation is developed to study the influence of the capsular clustering on the fracture mechanism by varying the contact surface area of the CS between the microcapsule shell and the concrete matrix. The proposed fracture simulation is expanded to 3D simulations to validate the 2D computational simulations and to estimate the accuracy difference ratio between 2D and 3D simulations. In addition, a proposed design method is developed to design the size of the microcapsules consideration of a sufficient volume of healing agent to heal the expected crack width. This method is based on the configuration of the unit cell (UC), Representative Volume Element (RVE), Periodic Boundary Conditions (PBC), and associated them to the volume fraction (Vf) and the crack width as variables. The proposed microcapsule design is verified through computational fracture simulations. KW - Beton KW - Bruchverhalten KW - Finite-Elemente-Methode KW - Self-healing concrete KW - Computational fracture modeling KW - Capsular clustering; Design of microcapsules KW - XFEM KW - Cohesive surface technique KW - Mikrokapsel KW - Selbstheilendem Beton KW - Computermodellierung des Bruchverhaltens KW - Entwurf von Mikrokapseln KW - Kapselclustern KW - Erweiterte Finite-Elemente-Methode KW - Kohäsionsflächenverfahren Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20221124-47467 ER - TY - THES A1 - Heidolf, Thorsten T1 - Zeit- und beanspruchungsabhängiges Tragverhalten von polymermodifiziertem Beton unter mehrfach wiederholter Beanspruchung T1 - Time- and Strain-Dependent Behaviour of Polymer-Modified Concrete with Multifariously Repeated Load N2 - In der vorliegenden Arbeit werden die experimentellen Ergebnisse eigener Untersuchungen an unbewehrtem und bewehrtem polymermodifiziertem Beton unter mehrfach wiederholter Druck- und Zugbeanspruchung vorgestellt und mit den Ergebnissen ähnlicher Versuche an Normalbeton und hochfestem Beton verglichen. Besondere Aufmerksamkeit wird dabei dem Formänderungsverhalten, der Steifigkeitsdegradation und der Energiedissipation sowie dem Kriechverhalten und der Mitwirkung des Betons zwischen den Rissen gewidmet. Die beobachtete signifikante Steifigkeitsdegradation sowie der ausgeprägt nichtlineare Zusammenhang zwischen der viskosen Verformung und der elastischen Stauchung zeigen, dass bei der Analyse der Kriech¬aus¬wirkungen des polymermodifizierten Betons auf das Tragverhalten entsprechender Kon¬struktionen neben den Gebrauchslasten auch die während der Lastgeschichte aufgetretenen maximalen Beanspruchungssituationen sowie die damit verbundenen Strukturveränderungen zu berücksichtigen sind. Auf der Basis der Versuchsergebnisse und der visko-elastisch-plastischen Kontinuumsschädigungstheorie werden rheologische Modelle zur Beschreibung des zeit- und beanspruchungsabhängigen Tragverhaltens von Betonbauteile vorgeschlagen. Die numerische Umsetzung der vorgeschlagenen Modelle erfolgt unter Berücksichtigung des zeitabhängigen Materialverhaltens des Betons auf der Basis des HAMILTON-Prinzips unter Vernachlässigung der Trägheitskräfte. Durch eine zeitliche Diskretisierung kann die Problembeschreibung auf das Prinzip von LAGRANGE vom Minimum des Gesamtpotentials zurückgeführt und als nichtlineare Optimierungsaufgabe formuliert werden. Die Simulation des beanspruchungsabhängigen Tragverhaltens von Stahlbetonverbundquerschnitten verdeutlicht die Qualität und Leistungsfähigkeit der vorgeschlagenen Modellbildung. N2 - The experimental results of the investigations into polymer-modified concrete with multifariously repeated compression or tension load are introduced in the provided work and compared to similar experiments in normal- and high-strength concrete. Special attention is dedicated to the stress-strain relation, the degradation of stiffness and the dissipation of energy as well as the non-linear long-term behaviour and tension-stiffening. Stiffness degradation and non-linear creep of polymer-modified concrete show that maximum strain situations have to be taken into consideration of the behaviour analysis of concrete structures under long-term loading. Based on experimental results and the theory of visco-elastic-plastic continuum damage, rheological models are suggested for the description of the time- and damage-dependent behaviour of reinforced concrete. The numerical concept is based on the HAMILTON-principle. Using time discretisation, mechanical modelling simplifies and can be described as a LAGRANGE-principle concerning minimum of total potential energy. The problem is solved by non-linear optimisation. The efficiency of the suggested model was proven for reinforced concrete cross sections by numerical simulation. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 10 KW - Kriechen KW - Kunstharzmodifizierter Zementbeton KW - Beton KW - Tragverhalten KW - Bruchverhalten KW - Experiment KW - Deformationsverhalten KW - Stoffgesetz KW - nichtlineare Optimierung KW - Simulation KW - Formänderungsenergie KW - Steifigkeitsdegradation KW - Creep KW - damage KW - tension-stiffening KW - dissipation of energy KW - non-linear optimisation Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20080102-11753 SN - 978-3-86068-331-2 ER - TY - THES A1 - Tartsch, Enrico T1 - Bewertung der Dauerstandfestigkeit von dampfgehärtetem Porenbeton auf der Grundlage von Kurzzeitversuchen T1 - Prediction of the Sustained Load Strength of Autoclaved Aerated Concrete on a Short-term Basis N2 - Im Rahmen der Arbeit wird das Tragverhalten von dampfgehärtetem Porenbeton unter einachsiger Druckbeanspruchung untersucht. Ziel ist es, einen Zusammenhang zwischen makroskopischen Spannungs-Dehnungs-Beziehungen, beanspruchungsbedingten Strukturänderungen und der Dauerstandfestigkeit herzustellen. Die Dauerstandfestigkeit stellt im Sinne der Arbeit eine elementare Gefügeschwelle dar, durch sie wird das stabile vom instabilen Tragverhalten abgegrenzt. Der Zusammenhang zwischen Strukturänderungen und Spannungs-Dehnungs-Verhalten wird anhand mechanischer Modelle analysiert. Diese Untersuchungen liefern die konzeptionelle Orientierung für die durchzuführenden Laborversuche. Die experimentelle Basis der Arbeit bilden Kurzzeit- und Langzeitversuche an Porenbetonzylindern unter einachsiger Druckbeanspruchung. Es werden Probekörper von drei Porenbetonwerken untersucht. Um den Einfluss der Lastgeschichte aufzuzeigen, wird die Versuchsdauer zwischen einer Sekunde und mehreren Wochen variiert. Die Versuche werden mit unterschiedlichen Lastregimen durchgeführt: sowohl mit monoton gesteigerter Beanspruchung bis zum Versagen bzw. bis zum vorgesehenen Beanspruchungsniveau als auch mit niederzyklischer Beanspruchung. Die Messdaten werden unter Einbeziehung der dreidimensionalen Ansätze der Spannungs- und Deformationstheorie hinsichtlich des sphärischen und des deviatorischen Anteils des Spannungs- und Verformungszustandes ausgewertet. Diese auf die separate Betrachtung der Volumen- und Gestaltänderung gestützte Auswertung liefert zusätzliche Erkenntnisse hinsichtlich der Zuordnung von reversiblen und irreversiblen Verformungen zu den Teiltensoräquivalenten. Entsprechend den Versuchsergebnissen ändert sich die Kompressibilität des Porenbetons belastungsabhängig. Bereits kurzzeitige Überlastungen oberhalb der experimentell ermittelten Dauerstandgrenze sind von signifikanten Änderungen der Kompressionssteifigkeit begleitet. Das qualitative Tragverhalten des Porenbetons, das bei Beanspruchungen oberhalb der Dauerstandfestigkeit grundsätzliche Änderungen erfährt, lässt sich so bereits im Kurzzeitversuch abgrenzen. Zusätzliche Auswertungen für Normalbeton und selbstverdichtenden hochfesten Beton weisen auf analoges Verhalten hin. Auf der Basis der durchgeführten Untersuchungen werden Konzepte vorgestellt, mit denen die Dauerstandfestigkeit im Kurzzeitversuch, das heißt mit einer Versuchsdauer von wenigen Stunden, prognostiziert werden kann. Damit können Untersuchungen zur Dauerstandfestigkeit, die eine grundlegende Größe zur Beurteilung der Tragfähigkeit darstellt, routinemäßig durchgeführt werden. N2 - This thesis is concerned with the behaviour of autoclaved aerated concrete (AAC) when it is subjected to uniaxial compressive loads. The objective is to ascertain the relationship between textural changes, macroscopic stress-strain relations and the sustained load strength of the material itself. Throughout the thesis, the sustained load strength is considered as a basic threshold level, i.e. as the boundary between stable and unstable load-bearing behaviour. First, the effect of textural changes on the stress-strain behaviour was analysed on a theoretical basis with the aid of mechanical models. Based on the results, experimental tests were then planned. Short-term as well as long-term tests were carried out using cylindrical specimens made of AAC. Three different types of AAC were tested. Different load histories were used: monotonically increased loads and low-cycle loads with the load level increased step by step. Within the context of the test data analysis, three-dimensional textural responses are taken into account. Uniaxial loading is regarded as a special case of multi-axial loading. The decomposition of the stress tensor and strain tensor respectively opens up the opportunity to obtain more detailed information about elastic and inelastic material properties. It can be shown that compressibility of AAC undergoes load-dependent changes. Even short-term overloads lead to significant textural changes; these can be detected by analysing the bulk modulus. On this basis, it is possible to give clear statements about the sustained load strength of AAC. Additional tests carried out on normal-strength concrete and self-compacting concrete display similar behaviour. This study outlines a way of predicting sustained load strength on a short-term basis. As a result, it will be possible to carry out routine investigations into the sustained load strength in the future. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 12 KW - Porenbeton KW - Beton KW - Tragverhalten KW - Dauerstandfestigkeit KW - Bruchverhalten KW - Experiment KW - Deformationsverhalten KW - zyklisch KW - Strukturänderung KW - elastische Eigenschaften KW - sphärisch KW - deviatorisch KW - Kompressibilität KW - textural changes KW - elastic properties KW - spherical KW - deviatoric KW - compressibility Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20080213-12926 ER -