TY - JOUR A1 - Bore, Thierry A1 - Wagner, Norman A1 - Lesoille, Sylvie Delepine A1 - Taillade, Frederic A1 - Six, Gonzague A1 - Daout, Franck A1 - Placko, Dominique T1 - Error analysis of clay-rock water content estimation with broadband high-frequency electromagnetic sensors—air gap effect JF - Sensors N2 - Broadband electromagnetic frequency or time domain sensor techniques present high potential for quantitative water content monitoring in porous media. Prior to in situ application, the impact of the relationship between the broadband electromagnetic properties of the porous material (clay-rock) and the water content on the frequency or time domain sensor response is required. For this purpose, dielectric properties of intact clay rock samples experimental determined in the frequency range from 1 MHz to 10 GHz were used as input data in 3-D numerical frequency domain finite element field calculations to model the one port broadband frequency or time domain transfer function for a three rods based sensor embedded in the clay-rock. The sensor response in terms of the reflection factor was analyzed in time domain with classical travel time analysis in combination with an empirical model according to Topp equation, as well as the theoretical Lichtenecker and Rother model (LRM) to estimate the volumetric water content. The mixture equation considering the appropriate porosity of the investigated material provide a practical and efficient approach for water content estimation based on classical travel time analysis with the onset-method. The inflection method is not recommended for water content estimation in electrical dispersive and absorptive material. Moreover, the results clearly indicate that effects due to coupling of the sensor to the material cannot be neglected. Coupling problems caused by an air gap lead to dramatic effects on water content estimation, even for submillimeter gaps. Thus, the quantitative determination of the in situ water content requires careful sensor installation in order to reach a perfect probe clay rock coupling. KW - Wassergehalt KW - Ton KW - Zeitbereichsreflektometrie KW - Impedanzspektroskopie KW - Dielektrische Spektroskopie KW - water content measurement; TDR probe; clay-rock; dielectric spectroscopy; frequency domain finite element modeling Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170418-31248 UR - https://www.scopus.com/inward/record.uri?eid=2-s2.0-84964200266&doi=10.3390%2fs16040554&partnerID=40&md5=26e537724db3b28e237009acde7676cd SP - 1 EP - 14 ER - TY - JOUR A1 - Bourikas, Leonidas A1 - James, Patrick A. B. A1 - Bahaj, AbuBakr S. A1 - Jentsch, Mark F. A1 - Shen, Tianfeng A1 - Chow, David H. C. A1 - Darkwa, Jo T1 - Transforming typical hourly simulation weather data files to represent urban locations by using a 3D urban unit representation with micro-climate simulations JF - Future Cities and Environment N2 - Urban and building energy simulation models are usually driven by typical meteorological year (TMY) weather data often in a TMY2 or EPW format. However, the locations where these historical datasets were collected (usually airports) generally do not represent the local, site specific micro-climates that cities develop. In this paper, a humid sub-tropical climate context has been considered. An idealised “urban unit model” of 250 m radius is being presented as a method of adapting commonly available weather data files to the local micro-climate. This idealised “urban unit model” is based on the main thermal and morphological characteristics of nine sites with residential/institutional (university) use in Hangzhou, China. The area of the urban unit was determined by the region of influence on the air temperature signal at the centre of the unit. Air temperature and relative humidity were monitored and the characteristics of the surroundings assessed (eg green-space, blue-space, built form). The “urban unit model” was then implemented into micro-climatic simulations using a Computational Fluid Dynamics – Surface Energy Balance analysis tool (ENVI-met, Version 4). The “urban unit model” approach used here in the simulations delivered results with performance evaluation indices comparable to previously published work (for air temperature; RMSE <1, index of agreement d > 0.9). The micro-climatic simulation results were then used to adapt the air temperature and relative humidity of the TMY file for Hangzhou to represent the local, site specific morphology under three different weather forcing cases, (ie cloudy/rainy weather (Group 1), clear sky, average weather conditions (Group 2) and clear sky, hot weather (Group 3)). Following model validation, two scenarios (domestic and non-domestic building use) were developed to assess building heating and cooling loads against the business as usual case of using typical meteorological year data files. The final “urban weather projections” obtained from the simulations with the “urban unit model” were used to compare the degree days amongst the reference TMY file, the TMY file with a bulk UHI offset and the TMY file adapted for the site-specific micro-climate (TMY-UWP). The comparison shows that Heating Degree Days (HDD) of the TMY file (1598 days) decreased by 6 % in the “TMY + UHI” case and 13 % in the “TMY-UWP” case showing that the local specific micro-climate is attributed with an additional 7 % (ie from 6 to 13 %) reduction in relation to the bulk UHI effect in the city. The Cooling Degree Days (CDD) from the “TMY + UHI” file are 17 % more than the reference TMY (207 days) and the use of the “TMY-UWP” file results to an additional 14 % increase in comparison with the “TMY + UHI” file (ie from 17 to 31 %). This difference between the TMY-UWP and the TMY + UHI files is a reflection of the thermal characteristics of the specific urban morphology of the studied sites compared to the wider city. A dynamic thermal simulation tool (TRNSYS) was used to calculate the heating and cooling load demand change in a domestic and a non-domestic building scenario. The heating and cooling loads calculated with the adapted TMY-UWP file show that in both scenarios there is an increase by approximately 20 % of the cooling load and a 20 % decrease of the heating load. If typical COP values for a reversible air-conditioning system are 2.0 for heating and 3.5 for cooling then the total electricity consumption estimated with the use of the “urbanised” TMY-UWP file will be decreased by 11 % in comparison with the “business as usual” (ie reference TMY) case. Overall, it was found that the proposed method is appropriate for urban and building energy performance simulations in humid sub-tropical climate cities such as Hangzhou, addressing some of the shortfalls of current simulation weather data sets such as the TMY. KW - Mikroklima KW - Simulation KW - Stadt KW - Wetter KW - Idealised urban unit model, Micro-climate simulations, Urban weather projections, Cities Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170418-31348 UR - http://link.springer.com/article/10.1186/s40984-016-0020-4 ER - TY - JOUR A1 - Bremer, K. A1 - Wollweber, M. A1 - Weigand, F. A1 - Rahlves, M. A1 - Kuhne, Michael A1 - Helbig, R. A1 - Roth, B. T1 - Fibre Optic Sensors for the Structural Health Monitoring of Building Structures JF - Procedia Technology 26 N2 - In this work different fibre optic sensors for the structural health monitoring of civil engineering structures are reported. A fibre optic crack sensor and two different fibre optic moisture sensors have been designed to detect the moisture ingress in concrete based building structures. Moreover, the degeneration of the mechanical properties of optical glass fibre sensors and hence their long-term stability and reliability due to the mechanical and chemical impact of the concrete environment is discussed as well as the advantage of applying a fibre optic sensor system for the structural health monitoring of sewerage tunnels is demonstrated. KW - Structural Health Monitoring KW - crack sensor; fibre optic sensor; humidity sensor; SHM Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170331-30912 UR - http://www.sciencedirect.com/science/article/pii/S2212017316304121 SP - 524 EP - 529 ER - TY - JOUR A1 - Daube, Dirk A1 - Metzner, Steffen T1 - Priorisierung von energetischen Maßnahmen in heterogenen Immobilienportfolios – Am Beispiel eines Bestandes der öffentlichen Hand JF - Zeitschrift für Immobilienökonomie N2 - In vielen öffentlichen Gebäuden besteht ein hohes wirtschaftliches Einsparpotenzial bei den relevanten Energieträgern Wärme und Strom. Projekte zur energetischen Optimierungen refinanzieren sich häufig nach wenigen Jahren. Die notwenigen Investitionsmittel stehen jedoch nur begrenzt zur Verfügung. Zielgerichtete Analysen und Potenzialschätzungen sind erforderlich, um eine Priorisierung optionaler Maßnahmen zu erreichen. Die Studie zeigt anhand eines öffentlichen Portfolios notwendige Untersuchungsschritte auf. Die Einzelpotenziale werden über geeignete Benchmarks ermittelt. Auf Portfolioebene werden u. a. spezifische Potenzial-Matrizen genutzt. Die kennzahlenbasierte Priorisierung von Maßnahmen ist umso wichtiger, je stärker das Potenzial auf wenige Objekte konzentriert ist. KW - Öffentlicher Sektor KW - Energieverbrauch KW - Kosten-Nutzen-Analyse KW - Controlling KW - Entscheidungsunterstützung Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170418-31332 UR - http://link.springer.com/article/10.1365/s41056-016-0011-4 SP - 53 EP - 79 ER - TY - JOUR A1 - Dressel, Dennys T1 - Reaktivität von Hüttensand : Thermodynamische Grundlagen und Anwendung N2 - Die thermodynamischen Grundlagen der Hydratation von Hüttensand als Hauptbestandteil von Zementen werden erforscht. Hierbei werden thermodynamische Bildungs- und Reaktionsdaten experimentell bestimmt und berechnet. Darüber hinaus wird der Prozess der Feststoffauflösung von Hüttensand in wässrigen Lösungen untersucht. Lösungs- und Fällungsprozesse werden unter verschiedenen Konditionen gemessen, ausgewertet und diskutiert. Die Ergebnisse werden im weiteren Verlauf zur Bestimmung der Hydratationsgrades in Pasten sowie zum besseren Verständnis in der Wechselwirkung zwischen Hüttensanden und Mahlhilfsstoffen genutzt und angewandt. KW - Hüttensand KW - Thermodynamik Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20160829-26778 ER - TY - JOUR A1 - Elrasoul, Riham T1 - City Architectural Heritage Revival: The Need of a New Applied Approach JF - Procedia - Social and Behavioral Sciences 225 N2 - Egypt is a nation of 4000 years of civilization, which was known for its ancient architecture that occupied the highest rank of importance, but how long will our neglected heritage sites survive in our recent era? This is a rising debate. This paper is based on a hypothesis whether the conservation of the neglected or isolated heritage sites, particularly in the inhabited areas, can bind the citizens to their past. For this reason, the research provides scenes of many applied conservation practices in other countries. The study calls for developing a new applied approach of conservation that takes the interaction between citizens and the city heritage zones into consideration. KW - Sozialisation KW - Renovierung KW - Commercialization; Comprehencive; Memorlization; Renovation; Socialization Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170401-30977 UR - http://www.sciencedirect.com/science/article/pii/S1877042816307066 SP - 216 EP - 225 ER - TY - JOUR A1 - Faridmehr, Iman A1 - Tahir, Mamood Md. A1 - Lahmer, Tom T1 - Classification System for Semi-Rigid Beam-to-Column Connections JF - LATIN AMERICAN JOURNAL OF SOLIDS AND STRUCTURES 11 N2 - The current study attempts to recognise an adequate classification for a semi-rigid beam-to-column connection by investigating strength, stiffness and ductility. For this purpose, an experimental test was carried out to investigate the moment-rotation (M-theta) features of flush end-plate (FEP) connections including variable parameters like size and number of bolts, thickness of end-plate, and finally, size of beams and columns. The initial elastic stiffness and ultimate moment capacity of connections were determined by an extensive analytical procedure from the proposed method prescribed by ANSI/AISC 360-10, and Eurocode 3 Part 1-8 specifications. The behaviour of beams with partially restrained or semi-rigid connections were also studied by incorporating classical analysis methods. The results confirmed that thickness of the column flange and end-plate substantially govern over the initial rotational stiffness of of flush end-plate connections. The results also clearly showed that EC3 provided a more reliable classification index for flush end-plate (FEP) connections. The findings from this study make significant contributions to the current literature as the actual response characteristics of such connections are non-linear. Therefore, such semirigid behaviour should be used to for an analysis and design method. KW - Tragfähigkeit KW - Stütze KW - Träger KW - Beam-to-column connection; semi-rigid; flush end-plate connection; moment-rotation curve Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170401-30988 SP - 2152 EP - 2175 ER - TY - JOUR A1 - Frisch, Simon ED - Frisch, Simon ED - Orth, Dominik ED - Schmidt, Oliver T1 - Kire – ‚Reine Gewalt‘ im japanischen Film JF - Rabbit Eye - Zeitschrift für Filmforschung N2 - Das japanische Prinzip des Schnittkontinuums (kire-tsuzuki) als Horizont für eine Theorie der filmischen Ästhetik KW - Japanischer Film KW - Schnitt KW - Kire KW - Japan KW - Film KW - Montage Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20190508-39001 SP - 79 EP - 97 ER - TY - JOUR A1 - Frommholz, Ingo A1 - Haider M., al-Khateeb A1 - Potthast, Martin A1 - Ghasem, Zinnar A1 - Shukla, Mitul A1 - Short, Emma T1 - On Textual Analysis and Machine Learning for Cyberstalking Detection JF - Datenbank Spektrum N2 - Cyber security has become a major concern for users and businesses alike. Cyberstalking and harassment have been identified as a growing anti-social problem. Besides detecting cyberstalking and harassment, there is the need to gather digital evidence, often by the victim. To this end, we provide an overview of and discuss relevant technological means, in particular coming from text analytics as well as machine learning, that are capable to address the above challenges. We present a framework for the detection of text-based cyberstalking and the role and challenges of some core techniques such as author identification, text classification and personalisation. We then discuss PAN, a network and evaluation initiative that focusses on digital text forensics, in particular author identification. KW - Text Mining KW - Maschinelles Lernen Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20170418-31352 SP - 127 EP - 135 ER - TY - JOUR A1 - Ghorashi, Seyed Shahram A1 - Lahmer, Tom A1 - Bagherzadeh, Amir Saboor A1 - Zi, Goangseup A1 - Rabczuk, Timon T1 - A stochastic computational method based on goal-oriented error estimation for heterogeneous geological materials JF - Engineering Geology N2 - A stochastic computational method based on goal-oriented error estimation for heterogeneous geological materials KW - Angewandte Mathematik KW - Stochastik KW - Strukturmechanik Y1 - 2016 ER -