Dokument-ID Dokumenttyp Verfasser/Autoren Herausgeber Haupttitel Abstract Auflage Verlagsort Verlag Erscheinungsjahr Seitenzahl Schriftenreihe Titel Schriftenreihe Bandzahl ISBN Quelle der Hochschulschrift Konferenzname Quelle:Titel Quelle:Jahrgang Quelle:Heftnummer Quelle:Erste Seite Quelle:Letzte Seite URN DOI Abteilungen
OPUS4-2716 Dissertation Abbas, Tajammal Assessment of Numerical Prediction Models for Aeroelastic Instabilities of Bridges The phenomenon of aerodynamic instability caused by the wind is usually a major design criterion for long-span cable-supported bridges. If the wind speed exceeds the critical flutter speed of the bridge, this constitutes an Ultimate Limit State. The prediction of the flutter boundary, therefore, requires accurate and robust models. The complexity and uncertainty of models for such engineering problems demand strategies for model assessment. This study is an attempt to use the concepts of sensitivity and uncertainty analyses to assess the aeroelastic instability prediction models for long-span bridges. The state-of-the-art theory concerning the determination of the flutter stability limit is presented. Since flutter is a coupling of aerodynamic forcing with a structural dynamics problem, different types and classes of structural and aerodynamic models can be combined to study the interaction. Here, both numerical approaches and analytical models are utilised and coupled in different ways to assess the prediction quality of the coupled model. Weimar Jonas Verlag 275 urn:nbn:de:gbv:wim2-20180515-27161 10.25643/bauhaus-universitaet.2716 Institut für Strukturmechanik
OPUS4-3741 Dissertation Zhu, Pengtao The Variability of the Void Ratio of Sand and its Effect on Settlement and Infinite Slope Stability The uncertainty of a soil property can significantly affect the physical behavior of soil, so as to influence geotechnical practice. The uncertainty can be expressed by its stochastic parameters, including the mean, the standard deviation, and the spatial correlation length. These stochastic parameters are regarded as constant value in most of the former studies. The main aim of this thesis is to prove whether they are depth-dependent, and to evaluate the effect of this depth-dependent character on both the settlement and the infinite slope stability during rainwater infiltration. A stochastic one-dimensional settlement simulation is carried out using random finite element method with the von Wolffersdorff hypoplastic model, so as to evaluate the effect of stress level on the stochastic parameters of void ratio related parameters of sand. It is found that these stochastic parameters are both stress-dependent and depth-dependent. The non-stationary random field, considering the depth-dependent character of these stochastic parameters, can be generated through the distortion of the stationary random field. The one-dimensional settlement analysis is carried out to evaluation the effect of the depth-dependent character of the stochastic parameters of void ratio on the strain. It is found that the depth-dependent character has low effect on the strain. The deterministic analysis of infinite slope stability during rainwater infiltration is simulated. The transient seepage is carried out using finite difference method, while the steady state seepage is simulated using the analytical solution. The saturated hydraulic conductivity (ks) is taken as the only variable. The results show that the depth-dependent ks has a significant influence on the stability of the slope when the negative flux is high. Without considering the depth-dependent character, can overestimate the factor of safety of the slope. A slope can fail if the depth-dependent character is considered, while it is stable if the depth-dependent character is neglected. The failure time of the slope with a greater depth-dependent ks is earlier during transient infiltration. Meanwhile, the stochastic infinite slope stability analysis during infiltration, is also carried out to highlight the effect of the depth-dependent character of the stochastic parameters of ks. The results show that: the probability of failure is significantly increased if the depth-dependent character of mean is considered, while, it is moderately reduced if the depth-dependent character of the standard deviation is accounted. If the depth-dependent character of both the mean and standard deviation of ks is considered, the depth-dependent mean value plays a dominant influence on the results. Furthermore, the depth-dependent character of the spatial correlation length can slightly reduce the probability of failure. 164 urn:nbn:de:gbv:wim2-20180403-37411 10.25643/bauhaus-universitaet.3741 Professur Grundbau
OPUS4-4183 Dissertation Salavati, Mohammad Multi-Scale Modeling of Mechanical and Electrochemical Properties of 1D and 2D Nanomaterials, Application in Battery Energy Storage Systems Material properties play a critical role in durable products manufacturing. Estimation of the precise characteristics in different scales requires complex and expensive experimental measurements. Potentially, computational methods can provide a platform to determine the fundamental properties before the final experiment. Multi-scale computational modeling leads to the modeling of the various time, and length scales include nano, micro, meso, and macro scales. These scales can be modeled separately or in correlation with coarser scales. Depend on the interested scales modeling, the right selection of multi-scale methods leads to reliable results and affordable computational cost. The present dissertation deals with the problems in various length and time scales using computational methods include density functional theory (DFT), molecular mechanics (MM), molecular dynamics (MD), and finite element (FE) methods. Physical and chemical interactions in lower scales determine the coarser scale properties. Particles interaction modeling and exploring fundamental properties are significant challenges of computational science. Downscale modelings need more computational effort due to a large number of interacted atoms/particles. To deal with this problem and bring up a fine-scale (nano) as a coarse-scale (macro) problem, we extended an atomic-continuum framework. The discrete atomic models solve as a continuum problem using the computationally efficient FE method. MM or force field method based on a set of assumptions approximates a solution on the atomic scale. In this method, atoms and bonds model as a harmonic oscillator with a system of mass and springs. The negative gradient of the potential energy equal to the forces on each atom. In this way, each bond's total potential energy includes bonded, and non-bonded energies are simulated as equivalent structural strain energies. Finally, the chemical nature of the atomic bond is modeled as a piezoelectric beam element that solves by the FE method. Exploring novel materials with unique properties is a demand for various industrial applications. During the last decade, many two-dimensional (2D) materials have been synthesized and shown outstanding properties. Investigation of the probable defects during the formation/fabrication process and studying their strength under severe service life are the critical tasks to explore performance prospects. We studied various defects include nano crack, notch, and point vacancy (Stone-Wales defect) defects employing MD analysis. Classical MD has been used to simulate a considerable amount of molecules at micro-, and meso- scales. Pristine and defective nanosheet structures considered under the uniaxial tensile loading at various temperatures using open-source LAMMPS codes. The results were visualized with the open-source software of OVITO and VMD. Quantum based first principle calculations have been conducting at electronic scales and known as the most accurate Ab initio methods. However, they are computationally expensive to apply for large systems. We used density functional theory (DFT) to estimate the mechanical and electrochemical response of the 2D materials. Many-body Schrödinger's equation describes the motion and interactions of the solid-state particles. Solid describes as a system of positive nuclei and negative electrons, all electromagnetically interacting with each other, where the wave function theory describes the quantum state of the set of particles. However, dealing with the 3N coordinates of the electrons, nuclei, and N coordinates of the electrons spin components makes the governing equation unsolvable for just a few interacted atoms. Some assumptions and theories like Born Oppenheimer and Hartree-Fock mean-field and Hohenberg-Kohn theories are needed to treat with this equation. First, Born Oppenheimer approximation reduces it to the only electronic coordinates. Then Kohn and Sham, based on Hartree-Fock and Hohenberg-Kohn theories, assumed an equivalent fictitious non-interacting electrons system as an electron density functional such that their ground state energies are equal to a set of interacting electrons. Exchange-correlation energy functionals are responsible for satisfying the equivalency between both systems. The exact form of the exchange-correlation functional is not known. However, there are widely used methods to derive functionals like local density approximation (LDA), Generalized gradient approximation (GGA), and hybrid functionals (e.g., B3LYP). In our study, DFT performed using VASP codes within the GGA/PBE approximation, and visualization/post-processing of the results realized via open-source software of VESTA. The extensive DFT calculations are conducted 2D nanomaterials prospects as anode/cathode electrode materials for batteries. Metal-ion batteries' performance strongly depends on the design of novel electrode material. Two-dimensional (2D) materials have developed a remarkable interest in using as an electrode in battery cells due to their excellent properties. Desirable battery energy storage systems (BESS) must satisfy the high energy density, safe operation, and efficient production costs. Batteries have been using in electronic devices and provide a solution to the environmental issues and store the discontinuous energies generated from renewable wind or solar power plants. Therefore, exploring optimal electrode materials can improve storage capacity and charging/discharging rates, leading to the design of advanced batteries. Our results in multiple scales highlight not only the proposed and employed methods' efficiencies but also promising prospect of recently synthesized nanomaterials and their applications as an anode material. In this way, first, a novel approach developed for the modeling of the 1D nanotube as a continuum piezoelectric beam element. The results converged and matched closely with those from experiments and other more complex models. Then mechanical properties of nanosheets estimated and the failure mechanisms results provide a useful guide for further use in prospect applications. Our results indicated a comprehensive and useful vision concerning the mechanical properties of nanosheets with/without defects. Finally, mechanical and electrochemical properties of the several 2D nanomaterials are explored for the first time—their application performance as an anode material illustrates high potentials in manufacturing super-stretchable and ultrahigh-capacity battery energy storage systems (BESS). Our results exhibited better performance in comparison to the available commercial anode materials. 166 urn:nbn:de:gbv:wim2-20200623-41830 10.25643/bauhaus-universitaet.4183 Institut für Strukturmechanik
OPUS4-4109 Dissertation Kavrakov, Igor Synergistic Framework for Analysis and Model Assessment in Bridge Aerodynamics and Aeroelasticity Wind-induced vibrations often represent a major design criterion for long-span bridges. This work deals with the assessment and development of models for aerodynamic and aeroelastic analyses of long-span bridges. Computational Fluid Dynamics (CFD) and semi-analytical aerodynamic models are employed to compute the bridge response due to both turbulent and laminar free-stream. For the assessment of these models, a comparative methodology is developed that consists of two steps, a qualitative and a quantitative one. The first, qualitative, step involves an extension of an existing approach based on Category Theory and its application to the field of bridge aerodynamics. Initially, the approach is extended to consider model comparability and completeness. Then, the complexity of the CFD and twelve semi-analytical models are evaluated based on their mathematical constructions, yielding a diagrammatic representation of model quality. In the second, quantitative, step of the comparative methodology, the discrepancy of a system response quantity for time-dependent aerodynamic models is quantified using comparison metrics for time-histories. Nine metrics are established on a uniform basis to quantify the discrepancies in local and global signal features that are of interest in bridge aerodynamics. These signal features involve quantities such as phase, time-varying frequency and magnitude content, probability density, non-stationarity, and nonlinearity. The two-dimensional (2D) Vortex Particle Method is used for the discretization of the Navier-Stokes equations including a Pseudo-three dimensional (Pseudo-3D) extension within an existing CFD solver. The Pseudo-3D Vortex Method considers the 3D structural behavior for aeroelastic analyses by positioning 2D fluid strips along a line-like structure. A novel turbulent Pseudo-3D Vortex Method is developed by combining the laminar Pseudo-3D VPM and a previously developed 2D method for the generation of free-stream turbulence. Using analytical derivations, it is shown that the fluid velocity correlation is maintained between the CFD strips. Furthermore, a new method is presented for the determination of the complex aerodynamic admittance under deterministic sinusoidal gusts using the Vortex Particle Method. The sinusoidal gusts are simulated by modeling the wakes of flapping airfoils in the CFD domain with inflow vortex particles. Positioning a section downstream yields sinusoidal forces that are used for determining all six components of the complex aerodynamic admittance. A closed-form analytical relation is derived, based on an existing analytical model. With this relation, the inflow particles' strength can be related with the target gust amplitudes a priori. The developed methodologies are combined in a synergistic framework, which is applied to both fundamental examples and practical case studies. Where possible, the results are verified and validated. The outcome of this work is intended to shed some light on the complex wind-bridge interaction and suggest appropriate modeling strategies for an enhanced design. Weimar Bauhaus-Universitätsverlag 314 978-3-95773-284-2 urn:nbn:de:gbv:wim2-20200316-41099 10.25643/bauhaus-universitaet.4109 Professur Modellierung und Simulation - Konstruktion
OPUS4-4003 Dissertation Grossmann, Albert Sicherheitskonzept zur Berücksichtigung von Korrosion an Gashochdruckleitungen aus Stählen Gashochdruckleitungen aus Stahl werden mit Hilfe eines deterministischen Sicherheitskonzeptes bemessen. Im unveränderten Bemessungszustand und im bestimmungsgemäßem Betrieb ist die statische Tragfähigkeit der Gashochdruckleitungen gegeben. Mit den Jahren unterliegen Gashochdruckleitungen aus Stahl geometrischen Veränderungen, die häufig durch Korrosion hervorgerufen werden. Die Beurteilung der statischen Tragfähigkeit erfolgt dann unter Berücksichtigung dieser geometrischen Änderung. Deterministische Sicherheitsbeiwerte der Bemessung neuer Gashochdruckleitungen können für die Bemessung bestehender korrosionsgeschädigter Gashochdruckleitungen nicht herangezogen werden, da diese einen definierten Beanspruchungs- und Geometriezustand unterstellen, welcher durch den geometrischen Einfluss der Korrosion so nicht mehr besteht. Die Arbeit befasst sich mit der Ermittlung deterministischer Sicherheitsbeiwerte für die Bemessung korrosionsgeschädigter Gashochdruckleitungen auf Basis von Versagenswahrscheinlichkeiten und stellt ein Anwendungskonzept zu deren Nutzung vor. 184 urn:nbn:de:gbv:wim2-20191021-40034 10.25643/bauhaus-universitaet.4003 Professur Stahl- und Hybridbau
OPUS4-3229 Dissertation Msekh, Mohammed Abdulrazzak Phase Field Modeling for Fracture with Applications to Homogeneous and Heterogeneous Materials The thesis presents an implementation including different applications of a variational-based approach for gradient type standard dissipative solids. Phase field model for brittle fracture is an application of the variational-based framework for gradient type solids. This model allows the prediction of different crack topologies and states. Of significant concern is the application of theoretical and numerical formulation of the phase field modeling into the commercial finite element software Abaqus in 2D and 3D. The fully coupled incremental variational formulation of phase field method is implemented by using the UEL and UMAT subroutines of Abaqus. The phase field method considerably reduces the implementation complexity of fracture problems as it removes the need for numerical tracking of discontinuities in the displacement field that are characteristic of discrete crack methods. This is accomplished by replacing the sharp discontinuities with a scalar damage phase field representing the diffuse crack topology wherein the amount of diffusion is controlled by a regularization parameter. The nonlinear coupled system consisting of the linear momentum equation and a diffusion type equation governing the phase field evolution is solved simultaneously via a Newton- Raphson approach. Post-processing of simulation results to be used as visualization module is performed via an additional UMAT subroutine implemented in the standard Abaqus viewer. In the same context, we propose a simple yet effective algorithm to initiate and propagate cracks in 2D geometries which is independent of both particular constitutive laws and specific element technology and dimension. It consists of a localization limiter in the form of the screened Poisson equation with, optionally, local mesh refinement. A staggered scheme for standard equilibrium and screened Cauchy equations is used. The remeshing part of the algorithm consists of a sequence of mesh subdivision and element erosion steps. Element subdivision is based on edge split operations using a given constitutive quantity (either damage or void fraction). Mesh smoothing makes use of edge contraction as function of a given constitutive quantity such as the principal stress or void fraction. To assess the robustness and accuracy of this algorithm, we use both quasi-brittle benchmarks and ductile tests. Furthermore, we introduce a computational approach regarding mechanical loading in microscale on an inelastically deforming composite material. The nanocomposites material of fully exfoliated clay/epoxy is shaped to predict macroscopic elastic and fracture related material parameters based on their fine-scale features. Two different configurations of polymer nanocomposites material (PNCs) have been studied. These configurations are fully bonded PNCs and PNCs with an interphase zone formation between the matrix and the clay reinforcement. The representative volume element of PNCs specimens with different clay weight contents, different aspect ratios, and different interphase zone thicknesses are generated by adopting Python scripting. Different constitutive models are employed for the matrix, the clay platelets, and the interphase zones. The brittle fracture behavior of the epoxy matrix and the interphase zones material are modeled using the phase field approach, whereas the stiff silicate clay platelets of the composite are designated as a linear elastic material. The comprehensive study investigates the elastic and fracture behavior of PNCs composites, in addition to predict Young's modulus, tensile strength, fracture toughness, surface energy dissipation, and cracks surface area in the composite for different material parameters, geometry, and interphase zones properties and thicknesses. 190 Phasenfeldmodellierung für Brüche mit Anwendungen auf homogene und heterogene Materialien urn:nbn:de:gbv:wim2-20170615-32291 10.25643/bauhaus-universitaet.3229 Institut für Strukturmechanik
OPUS4-3848 Dissertation Achenbach, Marcus Weiterentwicklung der Zonenmethode für den Nachweis der Feuerwiderstandsdauer von rechteckigen Stahlbetondruckgliedern Die Zonenmethode nach Hertz ist ein vereinfachtes Verfahren zur Heißbemessung von Stahlbetonbauteilen. Um eine händische Bemessung zu ermöglichen, werden daher verschiedene Annahmen und Vereinfachungen getroffen. Insbesondere werden die thermischen Dehnungen vernachlässigt und das mechanische Verhalten durch einen verkleinerten Querschnitt mit konstanten Stoffeigenschaften beschrieben. Ziel der vorliegenden Arbeit ist, dieses vereinfachte Verfahren in ein nichtlineares Verfahren zur Heißbemessung von Stahlbetondruckgliedern bei Brandbeanspruchung durch die Einheits-Temperaturzeitkurve zu überführen. Dazu werden die wesentlichen Annahmen der Zonenmethode überprüft und ein Vorschlag zur Weiterentwicklung vorgestellt. Dieser beruht im Wesentlichen auf der Modellierung der druckbeanspruchten Bewehrung. Diese weiterentwickelte Zonenmethode wird durch die Nachrechnung von Laborversuchen validiert und das Sicherheitsniveau durch eine vollprobabilistische Analyse und den Vergleich mit dem allgemeinen Verfahren bestimmt. Weimar Bauhaus-Universitätsverlag 174 978-3-95773-264-4 urn:nbn:de:gbv:wim2-20190119-38484 10.25643/bauhaus-universitaet.3848 Professur Modellierung und Simulation - Konstruktion
OPUS4-3710 Dissertation Nariman, Nazim Numerical Methods for the Multi-Physical Analysis of Long Span Cable-Stayed Bridges The main categories of wind effects on long span bridge decks are buffeting, flutter, vortex-induced vibrations (VIV) which are often critical for the safety and serviceability of the structure. With the rapid increase of bridge spans, research on controlling wind-induced vibrations of long span bridges has been a problem of great concern.The developments of vibration control theories have led to the wide use of tuned mass dampers (TMDs) which has been proven to be effective for suppressing these vibrations both analytically and experimentally. Fire incidents are also of special interest in the stability and safety of long span bridges due to significant role of the complex phenomenon through triple interaction between the deck with the incoming wind flow and the thermal boundary of the surrounding air. This work begins with analyzing the buffeting response and flutter instability of three dimensional computational structural dynamics (CSD) models of a cable stayed bridge due to strong wind excitations using ABAQUS finite element commercial software. Optimization and global sensitivity analysis are utilized to target the vertical and torsional vibrations of the segmental deck through considering three aerodynamic parameters (wind attack angle, deck streamlined length and viscous damping of the stay cables). The numerical simulations results in conjunction with the frequency analysis results emphasized the existence of these vibrations and further theoretical studies are possible with a high level of accuracy. Model validation is performed by comparing the results of lift and moment coefficients between the created CSD models and two benchmarks from the literature (flat plate theory) and flat plate by (Xavier and co-authors) which resulted in very good agreements between them. Optimum values of the parameters have been identified. Global sensitivity analysis based on Monte Carlo sampling method was utilized to formulate the surrogate models and calculate the sensitivity indices. The rational effect and the role of each parameter on the aerodynamic stability of the structure were calculated and efficient insight has been constructed for the stability of the long span bridge. 2D computational fluid dynamics (CFD) models of the decks are created with the support of MATLAB codes to simulate and analyze the vortex shedding and VIV of the deck. Three aerodynamic parameters (wind speed, deck streamlined length and dynamic viscosity of the air) are dedicated to study their effects on the kinetic energy of the system and the vortices shapes and patterns. Two benchmarks from the literature (Von Karman) and (Dyrbye and Hansen) are used to validate the numerical simulations of the vortex shedding for the CFD models. A good consent between the results was detected. Latin hypercube experimental method is dedicated to generate the surrogate models for the kinetic energy of the system and the generated lift forces. Variance based sensitivity analysis is utilized to calculate the main sensitivity indices and the interaction orders for each parameter. The kinetic energy approach performed very well in revealing the rational effect and the role of each parameter in the generation of vortex shedding and predicting the early VIV and the critical wind speed. Both one-way fluid-structure interaction (one-way FSI) simulations and two-way fluid-structure interaction (two-way FSI) co-simulations for the 2D models of the deck are executed to calculate the shedding frequencies for the associated wind speeds in the lock-in region in addition to the lift and drag coefficients. Validation is executed with the results of (Simiu and Scanlan) and the results of flat plate theory compiled by (Munson and co-authors) respectively. High levels of agreements between all the results were detected. A decrease in the critical wind speed and the shedding frequencies considering (two-way FSI) was identified compared to those obtained in the (one-way FSI). The results from the (two-way FSI) approach predicted appreciable decrease in the lift and drag forces as well as prediction of earlier VIV for lower critical wind speeds and lock-in regions which exist at lower natural frequencies of the system. These conclusions help the designers to efficiently plan and consider for the design and safety of the long span bridge before and after construction. Multiple tuned mass dampers (MTMDs) system has been applied in the three dimensional CSD models of the cable stayed bridge to analyze their control efficiency in suppressing both wind -induced vertical and torsional vibrations of the deck by optimizing three design parameters (mass ratio, frequency ratio and damping ratio) for the (TMDs) supporting on actual field data and minimax optimization technique in addition to MATLAB codes and Fast Fourier Transform technique. The optimum values of each parameter were identified and validated with two benchmarks from the literature, first with (Wang and co-authors) and then with (Lin and co-authors). The validation procedure detected a good agreement between the results. Box-Behnken experimental method is dedicated to formulate the surrogate models to represent the control efficiency of the vertical and torsional vibrations. Sobol's sensitivity indices are calculated for the design parameters in addition to their interaction orders. The optimization results revealed better performance of the MTMDs in controlling both the vertical and the torsional vibrations for higher mode shapes. Furthermore, the calculated rational effect of each design parameter facilitates to increase the control efficiency of the MTMDs in conjunction with the support of the surrogate models which simplifies the process of analysis for vibration control to a great extent. A novel structural modification approach has been adopted to eliminate the early coupling between the bending and torsional mode shapes of the cable stayed bridge. Two lateral steel beams are added to the middle span of the structure. Frequency analysis is dedicated to obtain the natural frequencies of the first eight mode shapes of vibrations before and after the structural modification. Numerical simulations of wind excitations are conducted for the 3D model of the cable stayed bridge. Both vertical and torsional displacements are calculated at the mid span of the deck to analyze the bending and the torsional stiffness of the system before and after the structural modification. The results of the frequency analysis after applying lateral steel beams declared that the coupling between the vertical and torsional mode shapes of vibrations has been removed to larger natural frequencies magnitudes and higher rare critical wind speeds with a high factor of safety. Finally, thermal fluid-structure interaction (TFSI) and coupled thermal-stress analysis are utilized to identify the effects of transient and steady state heat-transfer on the VIV and fatigue of the deck due to fire incidents. Numerical simulations of TFSI models of the deck are dedicated to calculate the lift and drag forces in addition to determining the lock-in regions once using FSI models and another using TFSI models. Vorticity and thermal fields of three fire scenarios are simulated and analyzed. The benchmark of (Simiu and Scanlan) is used to validate the TFSI models, where a good agreement was manifested between the two results. Extended finite element method (XFEM) is adopted to create 3D models of the cable stayed bridge to simulate the fatigue of the deck considering three fire scenarios. The benchmark of (Choi and Shin) is used to validate the damaged models of the deck in which a good coincide was seen between them. The results revealed that the TFSI models and the coupled thermal-stress models are significant in detecting earlier vortex induced vibration and lock-in regions in addition to predicting damages and fatigue of the deck and identifying the role of wind-induced vibrations in speeding up the damage generation and the collapse of the structure in critical situations. 236 urn:nbn:de:gbv:wim2-20171122-37105 10.25643/bauhaus-universitaet.3710 Institut für Strukturmechanik
OPUS4-4019 Dissertation Grossmann, Albert Sicherheitskonzept zur Berücksichtigung von Korrosion an Gashochdruckleitungen aus Stählen Gashochdruckleitungen aus Stahl werden mit Hilfe eines deterministischen Sicherheitskonzeptes bemessen. Im unveränderten Bemessungszustand und im bestimmungsgemäßem Betrieb ist die statische Tragfähigkeit der Gashochdruckleitungen gegeben. Mit den Jahren unterliegen Gashochdruckleitungen aus Stahl geometrischen Veränderungen, die häufig durch Korrosion hervorgerufen werden. Die Beurteilung der statischen Tragfähigkeit erfolgt dann unter Berücksichtigung dieser geometrischen Änderung. Deterministische Sicherheitsbeiwerte der Bemessung neuer Gashochdruckleitungen können für die Bemessung bestehender korrosionsgeschädigter Gashochdruckleitungen nicht herangezogen werden, da diese einen definierten Beanspruchungs- und Geometriezustand unterstellen, welcher durch den geometrischen Einfluss der Korrosion so nicht mehr besteht. Die Arbeit befasst sich mit der Ermittlung deterministischer Sicherheitsbeiwerte für die Bemessung korrosionsgeschädigter Gashochdruckleitungen auf Basis von Versagenswahrscheinlichkeiten und stellt ein Anwendungskonzept zu deren Nutzung vor. 184 urn:nbn:de:gbv:wim2-20191113-40199 10.25643/bauhaus-universitaet.4019 Professur Stahl- und Hybridbau
OPUS4-4579 Dissertation Hartmann, Veronika Methoden zur Quantifizierung und Optimierung der Robustheit von Bauablaufplänen Bauablaufplänen kommt bei der Realisierung von Bauprojekten eine zentrale Rolle zu. Sie dienen der Koordination von Schnittstellen und bilden für die am Projekt Beteiligten die Grundlage für ihre individuelle Planung. Eine verlässliche Terminplanung ist daher von großer Bedeutung, tatsächlich sind aber gerade Bauablaufpläne für ihre Unzuverlässigkeit bekannt. Aufgrund der langen Vorlaufzeiten bei der Planung von Bauprojekten sind zum Zeitpunkt der Planung viele Informationen nur als Schätzwerte bekannt. Auf der Grundlage dieser geschätzten und damit mit Unsicherheiten behafteten Daten werden im Bauwesen deterministische Terminpläne erstellt. Kommt es während der Realisierung zu Diskrepanzen zwischen Schätzungen und Realität, erfordert dies die Anpassung der Pläne. Aufgrund zahlreicher Abhängigkeiten zwischen den geplanten Aktivitäten können einzelne Planänderungen vielfältige weitere Änderungen und Anpassungen nach sich ziehen und damit einen reibungslosen Projektablauf gefährden. In dieser Arbeit wird ein Vorgehen entwickelt, welches Bauablaufpläne erzeugt, die im Rahmen der durch das Projekt definierten Abhängigkeiten und Randbedingungen in der Lage sind, Änderungen möglichst gut zu absorbieren. Solche Pläne, die bei auftretenden Änderungen vergleichsweise geringe Anpassungen des Terminplans erfordern, werden hier als robust bezeichnet. Ausgehend von Verfahren der Projektplanung und Methoden zur Berücksichtigung von Unsicherheiten werden deterministische Terminpläne bezüglich ihres Verhaltens bei eintretenden Änderungen betrachtet. Hierfür werden zunächst mögliche Unsicherheiten als Ursachen für Änderungen benannt und mathematisch abgebildet. Damit kann das Verhalten von Abläufen für mögliche Änderungen betrachtet werden, indem die durch Änderungen erzwungenen angepassten Terminpläne simuliert werden. Für diese Monte-Carlo-Simulationen der angepassten Terminpläne wird sichergestellt, dass die angepassten Terminpläne logische Weiterentwicklungen des deterministischen Terminplans darstellen. Auf der Grundlage dieser Untersuchungen wird ein stochastisches Maß zur Quantifizierung der Robustheit erarbeitet, welches die Fähigkeit eines Planes, Änderungen zu absorbieren, beschreibt. Damit ist es möglich, Terminpläne bezüglich ihrer Robustheit zu vergleichen. Das entwickelte Verfahren zur Quantifizierung der Robustheit wird in einem Optimierungsverfahren auf Basis Genetischer Algorithmen angewendet, um gezielt robuste Terminpläne zu erzeugen. An Beispielen werden die Methoden demonstriert und ihre Wirksamkeit nachgewiesen. urn:nbn:de:gbv:wim2-20220204-45798 10.25643/bauhaus-universitaet.4579 Professur Informatik im Bauwesen
OPUS4-2704 Dissertation Ghasemi, Hamid Stochastic optimization of fiber reinforced composites considering uncertainties Briefly, the two basic questions that this research is supposed to answer are: 1. Howmuch fiber is needed and how fibers should be distributed through a fiber reinforced composite (FRC) structure in order to obtain the optimal and reliable structural response? 2. How do uncertainties influence the optimization results and reliability of the structure? Giving answer to the above questions a double stage sequential optimization algorithm for finding the optimal content of short fiber reinforcements and their distribution in the composite structure, considering uncertain design parameters, is presented. In the first stage, the optimal amount of short fibers in a FRC structure with uniformly distributed fibers is conducted in the framework of a Reliability Based Design Optimization (RBDO) problem. Presented model considers material, structural and modeling uncertainties. In the second stage, the fiber distribution optimization (with the aim to further increase in structural reliability) is performed by defining a fiber distribution function through a Non-Uniform Rational BSpline (NURBS) surface. The advantages of using the NURBS surface as a fiber distribution function include: using the same data set for the optimization and analysis; high convergence rate due to the smoothness of the NURBS; mesh independency of the optimal layout; no need for any post processing technique and its non-heuristic nature. The output of stage 1 (the optimal fiber content for homogeneously distributed fibers) is considered as the input of stage 2. The output of stage 2 is the Reliability Index (b ) of the structure with the optimal fiber content and distribution. First order reliability method (in order to approximate the limit state function) as well as different material models including Rule of Mixtures, Mori-Tanaka, energy-based approach and stochastic multi-scales are implemented in different examples. The proposed combined model is able to capture the role of available uncertainties in FRC structures through a computationally efficient algorithm using all sequential, NURBS and sensitivity based techniques. The methodology is successfully implemented for interfacial shear stress optimization in sandwich beams and also for optimization of the internal cooling channels in a ceramic matrix composite. Finally, after some changes and modifications by combining Isogeometric Analysis, level set and point wise density mapping techniques, the computational framework is extended for topology optimization of piezoelectric / flexoelectric materials. 140 urn:nbn:de:gbv:wim2-20161117-27042 10.25643/bauhaus-universitaet.2704 Institut für Strukturmechanik
OPUS4-4037 Dissertation Hossain, Md Naim Isogeometric analysis based on Geometry Independent Field approximaTion (GIFT) and Polynomial Splines over Hierarchical T-meshes This thesis addresses an adaptive higher-order method based on a Geometry Independent Field approximatTion(GIFT) of polynomial/rationals plines over hierarchical T-meshes(PHT/RHT-splines). In isogeometric analysis, basis functions used for constructing geometric models in computer-aided design(CAD) are also employed to discretize the partial differential equations(PDEs) for numerical analysis. Non-uniform rational B-Splines(NURBS) are the most commonly used basis functions in CAD. However, they may not be ideal for numerical analysis where local refinement is required. The alternative method GIFT deploys different splines for geometry and numerical analysis. NURBS are utilized for the geometry representation, while for the field solution, PHT/RHT-splines are used. PHT-splines not only inherit the useful properties of B-splines and NURBS, but also possess the capabilities of local refinement and hierarchical structure. The smooth basis function properties of PHT-splines make them suitable for analysis purposes. While most problems considered in isogeometric analysis can be solved efficiently when the solution is smooth, many non-trivial problems have rough solutions. For example, this can be caused by the presence of re-entrant corners in the domain. For such problems, a tensor-product basis (as in the case of NURBS) is less suitable for resolving the singularities that appear since refinement propagates throughout the computational domain. Hierarchical bases and local refinement (as in the case of PHT-splines) allow for a more efficient way to resolve these singularities by adding more degrees of freedom where they are necessary. In order to drive the adaptive refinement, an efficient recovery-based error estimator is proposed in this thesis. The estimator produces a recovery solution which is a more accurate approximation than the computed numerical solution. Several two- and three-dimensional numerical investigations with PHT-splines of higher order and continuity prove that the proposed method is capable of obtaining results with higher accuracy, better convergence, fewer degrees of freedom and less computational cost than NURBS for smooth solution problems. The adaptive GIFT method utilizing PHT-splines with the recovery-based error estimator is used for solutions with discontinuities or singularities where adaptive local refinement in particular domains of interest achieves higher accuracy with fewer degrees of freedom. This method also proves that it can handle complicated multi-patch domains for two- and three-dimensional problems outperforming uniform refinement in terms of degrees of freedom and computational cost. 157 Die isogeometrische Analysis basierend auf der geometrieunabhängigen Feldnäherung (GIFT)und polynomialen Splines über hierarchischen T-Netzen urn:nbn:de:gbv:wim2-20191129-40376 10.25643/bauhaus-universitaet.4037 Institut für Strukturmechanik
OPUS4-4710 Dissertation López Zermeño, Jorge Alberto Isogeometric and CAD-based methods for shape and topology optimization: Sensitivity analysis, Bézier elements and phase-field approaches The Finite Element Method (FEM) is widely used in engineering for solving Partial Differential Equations (PDEs) over complex geometries. To this end, it is required to provide the FEM software with a geometric model that is typically constructed in a Computer-Aided Design (CAD) software. However, FEM and CAD use different approaches for the mathematical description of the geometry. Thus, it is required to generate a mesh, which is suitable for FEM, based on the CAD model. Nonetheless, this procedure is not a trivial task and it can be time consuming. This issue becomes more significant for solving shape and topology optimization problems, which consist in evolving the geometry iteratively. Therefore, the computational cost associated to the mesh generation process is increased exponentially for this type of applications. The main goal of this work is to investigate the integration of CAD and CAE in shape and topology optimization. To this end, numerical tools that close the gap between design and analysis are presented. The specific objectives of this work are listed below: • Automatize the sensitivity analysis in an isogeometric framework for applications in shape optimization. Applications for linear elasticity are considered. • A methodology is developed for providing a direct link between the CAD model and the analysis mesh. In consequence, the sensitivity analysis can be performed in terms of the design variables located in the design model. • The last objective is to develop an isogeometric method for shape and topological optimization. This method should take advantage of using Non-Uniform Rational B-Splines (NURBS) with higher continuity as basis functions. Isogeometric Analysis (IGA) is a framework designed to integrate the design and analysis in engineering problems. The fundamental idea of IGA is to use the same basis functions for modeling the geometry, usually NURBS, for the approximation of the solution fields. The advantage of integrating design and analysis is two-fold. First, the analysis stage is more accurate since the system of PDEs is not solved using an approximated geometry, but the exact CAD model. Moreover, providing a direct link between the design and analysis discretizations makes possible the implementation of efficient sensitivity analysis methods. Second, the computational time is significantly reduced because the mesh generation process can be avoided. Sensitivity analysis is essential for solving optimization problems when gradient-based optimization algorithms are employed. Automatic differentiation can compute exact gradients, automatically by tracking the algebraic operations performed on the design variables. For the automation of the sensitivity analysis, an isogeometric framework is used. Here, the analysis mesh is obtained after carrying out successive refinements, while retaining the coarse geometry for the domain design. An automatic differentiation (AD) toolbox is used to perform the sensitivity analysis. The AD toolbox takes the code for computing the objective and constraint functions as input. Then, using a source code transformation approach, it outputs a code for computing the objective and constraint functions, and their sensitivities as well. The sensitivities obtained from the sensitivity propagation method are compared with analytical sensitivities, which are computed using a full isogeometric approach. The computational efficiency of AD is comparable to that of analytical sensitivities. However, the memory requirements are larger for AD. Therefore, AD is preferable if the memory requirements are satisfied. Automatic sensitivity analysis demonstrates its practicality since it simplifies the work of engineers and designers. Complex geometries with sharp edges and/or holes cannot easily be described with NURBS. One solution is the use of unstructured meshes. Simplex-elements (triangles and tetrahedra for two and three dimensions respectively) are particularly useful since they can automatically parameterize a wide variety of domains. In this regard, unstructured Bézier elements, commonly used in CAD, can be employed for the exact modelling of CAD boundary representations. In two dimensions, the domain enclosed by NURBS curves is parameterized with Bézier triangles. To describe exactly the boundary of a two-dimensional CAD model, the continuity of a NURBS boundary representation is reduced to C^0. Then, the control points are used to generate a triangulation such that the boundary of the domain is identical to the initial CAD boundary representation. Thus, a direct link between the design and analysis discretizations is provided and the sensitivities can be propagated to the design domain. In three dimensions, the initial CAD boundary representation is given as a collection of NURBS surfaces that enclose a volume. Using a mesh generator (Gmsh), a tetrahedral mesh is obtained. The original surface is reconstructed by modifying the location of the control points of the tetrahedral mesh using Bézier tetrahedral elements and a point inversion algorithm. This method offers the possibility of computing the sensitivity analysis using the analysis mesh. Then, the sensitivities can be propagated into the design discretization. To reuse the mesh originally generated, a moving Bézier tetrahedral mesh approach was implemented. A gradient-based optimization algorithm is employed together with a sensitivity propagation procedure for the shape optimization cases. The proposed shape optimization approaches are used to solve some standard benchmark problems in structural mechanics. The results obtained show that the proposed approach can compute accurate gradients and evolve the geometry towards optimal solutions. In three dimensions, the moving mesh approach results in faster convergence in terms of computational time and avoids remeshing at each optimization step. For considering topological changes in a CAD-based framework, an isogeometric phase-field based shape and topology optimization is developed. In this case, the diffuse interface of a phase-field variable over a design domain implicitly describes the boundaries of the geometry. The design variables are the local values of the phase-field variable. The descent direction to minimize the objective function is found by using the sensitivities of the objective function with respect to the design variables. The evolution of the phase-field is determined by solving the time dependent Allen-Cahn equation. Especially for topology optimization problems that require C^1 continuity, such as for flexoelectric structures, the isogeometric phase field method is of great advantage. NURBS can achieve the desired continuity more efficiently than the traditional employed functions. The robustness of the method is demonstrated when applied to different geometries, boundary conditions, and material configurations. The applications illustrate that compared to piezoelectricity, the electrical performance of flexoelectric microbeams is larger under bending. In contrast, the electrical power for a structure under compression becomes larger with piezoelectricity. urn:nbn:de:gbv:wim2-20220831-47102 10.25643/bauhaus-universitaet.4710 Professur Modellierung und Simulation - Mechanik
OPUS4-4935 Dissertation Jaouadi, Zouhour Pareto and Reliability-Oriented Aeroelastic Shape Optimization of Bridge Decks Due to the development of new technologies and materials, optimized bridge design has recently gained more attention. The aim is to reduce the bridge components materials and the CO2 emission from the cement manufacturing process. Thus, most long-span bridges are designed to be with high flexibility, low structural damping, and longer and slender spans. Such designs lead, however, to aeroelastic challenges. Moreover, the consideration of both the structural and aeroelastic behavior in bridges leads to contradictory solutions as the structural constraints lead to deck prototypes with high depth which provide high inertia to material volume ratios. On the other hand, considering solely the aerodynamic requirements, slender airfoil-shaped bridge box girders are recommended since they prevent vortex shedding and exhibit minimum drag. Within this framework comes this study which provides approaches to find optimal bridge deck cross-sections while considering the aerodynamic effects. Shape optimization of deck cross-section is usually formulated to minimize the amount of material by finding adequate parameters such as the depth, the height, and the thickness and while ensuring the overall stability of the structure by the application of some constraints. Codes and studies have been implemented to analyze the wind phenomena and the structural responses towards bridge deck cross-sections where simplifications have been adopted due to the complexity and the uniqueness of such components besides the difficulty of obtaining a final model of the aerodynamic behavior. In this thesis, two main perspectives have been studied; the first is fully deterministic and presents a novel framework on generating optimal aerodynamic shapes for streamlined and trapezoidal cross-sections based on the meta-modeling approach. Single and multi-objective optimizations were both carried out and a Pareto Front is generated. The performance of the optimal designs is checked afterwards. In the second part, a new strategy based on Reliability-Based Design Optimization (RBDO) to mitigate the vortex-induced vibration (VIV) on the Trans-Tokyo Bay bridge is proposed. Small changes in the leading and trailing edges are presented and uncertainties are considered in the structural system. Probabilistic constraints based on polynomial regression are evaluated and the problem is solved while applying the Reliability Index Approach (RIA) and the Performance Measure Approach (PMA). The results obtained in the first part showed that the aspect ratio has a significant effect on the aerodynamic behavior where deeper cross-sections have lower resistance against flutter and should be avoided. In the second part, the adopted RBDO approach succeeded to mitigate the VIV, and it is proven that designs with narrow or prolonged bottom-base length and featuring an abrupt surface change in the leading and trailing edges can lead to high vertical vibration amplitude. It is expected that this research will help engineers with the selections of the adequate deck cross-section layout, and encourage researchers to apply concepts of optimization regarding this field and develop the presented approaches for further studies. 167 urn:nbn:de:gbv:wim2-20230303-49352 10.25643/bauhaus-universitaet.4935 Juniorprofessur Stochastik und Optimierung