Dokument-ID Dokumenttyp Verfasser/Autoren Herausgeber Haupttitel Abstract Auflage Verlagsort Verlag Erscheinungsjahr Seitenzahl Schriftenreihe Titel Schriftenreihe Bandzahl ISBN Quelle der Hochschulschrift Konferenzname Quelle:Titel Quelle:Jahrgang Quelle:Heftnummer Quelle:Erste Seite Quelle:Letzte Seite URN DOI Abteilungen
OPUS4-2881 Konferenzveröffentlichung Raue, Erich; Timmler, Hans-Georg; Schröter, Hendrik Gürlebeck, Klaus; Könke, Carsten NON-LINEAR ANALYSIS OF SHELLS OF REVOLUTION USING MATHEMATICAL OPTIMISATION In the paper presented, reinforced concrete shells of revolution are analyzed in both meridional and circumferential directions. Taking into account the physical non-linearity of the material, the internal forces and the deflections of the shell as well as the strain distribution at the cross-sections are calculated. The behavior of concrete under compression is described by linear and non-linear stress-strain relations. The description of the behavior of concrete under tension must account for tension stiffening effects. A tri-linear function is used to formulate the material law of reinforcement. The problem cannot be solved analytically due to the physical non-linearity. Thus a numerical solution is formulated by means of the LAGRANGE Principle of the minimum of the total potential energy. The kinematically admissible field of deformation is defined by the displacements u in the meridional and w in the radial direction. These displacements must satisfy the equations of compatibility and the kinematical boundary conditions of the shell. The strains are linearly distributed across the wall thickness. The strain energy depends on the specific of the material behavior. Using integral formulations of the material law [1], the strain energy of each part of the cross-section is defined as a function of the strains at the boundaries of the cross-sections. The shell is discretised in the meridional direction. Various methods of numerical differentiation and numerical integration are applied in order to determine the deformations and the strain energy. The unknown displacements u and w are calculated by a non-restricted extremum problem based on the minimum of the total potential energy. From mathematical point of view, the objective function is a convex function, thus the minimum can be determined without difficulty. The advantage of this formulation is that unlike non-linear methods with path-following algorithms the calculation does not have to account for changing stiffness and load increments. All iterations necessary to find the solution are integrated into the "Solver". The model presented provides many ways of investigating the influence of various material parameters on the stresses and deformations of the entire shell structure. 12 urn:nbn:de:gbv:wim2-20170314-28818 10.25643/bauhaus-universitaet.2881 Institut für Konstruktiven Ingenieurbau
OPUS4-3003 Konferenzveröffentlichung Raue, Erich; Timmler, Hans-Georg Gürlebeck, Klaus; Könke, Carsten NUMERISCHE ANALYSE VON VERBUNDQUERSCHNITTEN MIT NICHTLINEAREM MATERIALVERHALTEN UNTER BERüCKSICHTIGUNG VON VORVERFORMUNGEN The presented method for an physically non-linear analysis of stresses and deformations of composite cross-sections and members based on energy principles and their transformation to non-linear optimisation problems. From the LAGRANGE principle of minimum of total potential energy a kinematic formulation of the mechanical problem can be developed, which has the general advantage that pre-deformations excited by shrinkage, temperature, residual deformations after unloading et al., can be considered directly. Thus the non-linear analysis of composite cross-sections with layers of different mechanical properties and different preloading becomes possible and cracks in concrete, stiffness degradation and other specifics of the material behaviour can be taken into account without cardinal modification of the mathematical model. The impact of local defects on the bearing capacity of an entire element can also be analysed in this principle way. Standard computational systems for mathematical optimisation or general programs for spreadsheet analysis enable an uncomplicated implementation of the developed models and an effective non-linear analysis for composite cross-sections and elements. 9 urn:nbn:de:gbv:wim2-20170327-30039 10.25643/bauhaus-universitaet.3003 Institut für Konstruktiven Ingenieurbau