@article{VoelkerMaempelKornadt,
  author    = {V{\"o}lker, Conrad and M{\"a}mpel, Silvio and Kornadt, Oliver},
  title     = {Measuring the human body's micro-climate using a thermal manikin},
  series = {Indoor Air},
  journal   = {Indoor Air},
  number    = {24, 6},
  doi       = {10.25643/bauhaus-universitaet.3815},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20181025-38153},
  pages     = {567 -- 579},
  abstract  = {The human body is surrounded by a micro-climate which results from its convective release of heat. In this study, the air temperature and flow velocity of this micro-climate were measured in a climate chamber at various room temperatures, using a thermal manikin simulating the heat release of the human being. Different techniques (Particle Streak Tracking, thermography, anemometry, and thermistors) were used for measurement and visualization. The manikin surface temperature was adjusted to the particular indoor climate based on simulations with a thermoregulation model (UCBerkeley Thermal Comfort Model). We found that generally, the micro-climate is thinner at the lower part of the torso, but expands going up. At the head, there is a relatively thick thermal layer, which results in an ascending plume above the head. However, the micro-climate shape strongly depends not only on the body segment, but also on boundary conditions: the higher the temperature difference between the surface temperature of the manikin and the air temperature, the faster the air flow in the micro-climate. Finally, convective heat transfer coefficients strongly increase with falling room temperature, while radiative heat transfer coefficients decrease. The type of body segment strongly influences the convective heat transfer coefficient, while only minimally influencing the radiative heat transfer coefficient.},
  subject      = {Raumklima},
  language  = {en}
}
@article{VoelkerKornadtOstry,
  author    = {V{\"o}lker, Conrad and Kornadt, Oliver and Ostry, Milan},
  title     = {Temperature reduction due to the application of phase change materials},
  series = {Energy and Buildings},
  journal   = {Energy and Buildings},
  number    = {40, 5},
  doi       = {10.25643/bauhaus-universitaet.3816},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20181025-38166},
  pages     = {937 -- 944},
  abstract  = {Overheating is a major problem in many modern buildings due to the utilization of lightweight constructions with low heat storing capacity. A possible answer to this problem is the emplacement of phase change materials (PCM), thereby increasing the thermal mass of a building. These materials change their state of aggregation within a defined temperature range. Useful PCM for buildings show a phase transition from solid to liquid and vice versa. The thermal mass of the materials is increased by the latent heat. A modified gypsum plaster and a salt mixture were chosen as two materials for the study of their impact on room temperature reduction. For realistic investigations, test rooms were erected where measurements were carried out under different conditions such as temporary air change, alternate internal heat gains or clouding. The experimental data was finally reproduced by dint of a mathematical model.},
  subject      = {Raumklima},
  language  = {en}
}
@phdthesis{Tatarin,
  author    = {Tatarin, Ren{\´e}},
  title     = {Charakterisieren struktureller Ver{\"a}nderungen in zementgebundenen Baustoffen durch akustische zerst{\"o}rungsfreie Pr{\"u}fverfahren},
  publisher = {Cuvillier Verlag},
  address   = {G{\"o}ttingen},
  isbn      = {978-3-7369-7575-0},
  doi       = {10.25643/bauhaus-universitaet.4592},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220215-45920},
  school      = {Bauhaus-Universit{\"a}t Weimar},
  pages     = {293},
  abstract  = {Im Rahmen dieser Arbeit wird das Charakterisieren struktureller Ver{\"a}nderungen zementgebundener Baustoffe durch zwei auf dem Ultraschall-Transmissionsverfahren beruhenden Methoden der zerst{\"o}rungsfreien Pr{\"u}fung (ZfP) mit mechanischen Wellen vorgenommen. Zur kontinuierlichen Charakterisierung der Erstarrung und Erh{\"a}rtung frischer zementgebundener Systeme wird ein auf Ultraschallsensoren f{\"u}r Longitudinal- und Scherwellen basierendes Messsystem in Kombination mit zugeh{\"o}rigen Verfahrensweisen zur Datenauswertung konzipiert, charakterisiert und angewandt. Gegen{\"u}ber der bislang {\"u}blichen alleinigen Bewertung der Verfestigung anhand indirekter Ultraschallparameter wie Ausbreitungsgeschwindigkeit, Signalenergie oder Frequenzgehalt der Longitudinalwelle l{\"a}sst sich damit eine direkte, sensible Erfassung der sich w{\"a}hrend der Strukturbildung entwickelnden dynamischen elastischen Eigenschaften auf der Basis prim{\"a}rer physikalischer Werkstoffparameter erreichen. Insbesondere Scherwellen und der dynamische Schubmodul sind geeignet, den graduellen {\"U}bergang zum Festk{\"o}rper mit {\"U}berschreiten der Perkolationsschwelle sensibel und unabh{\"a}ngig vom Luftgehalt zu erfassen. Die zeitliche Entwicklung der dynamischen elastischen Eigenschaften, die Strukturbildungsraten sowie die daraus extrahierten diskreten Ergebnisparameter erm{\"o}glichen eine vergleichende quantitative Charakterisierung der Strukturbildung zementgebundener Baustoffe aus mechanischer Sicht. Dabei lassen sich typische, oft unvermeidbare Unterschiede in der Zusammensetzung der Versuchsmischungen ber{\"u}cksichtigen. Der Einsatz laserbasierter Methoden zur Anregung und Erfassung von mechanischen Wellen und deren Kombination zu Laser-Ultraschall zielt darauf ab, die mit der Anwendung des konventionellen Ultraschall-Transmissionsverfahrens verbundenen Nachteile zu eliminieren. Diese resultieren aus der Sensorgeometrie, der mechanischen Ankopplung und bei einer Vielzahl von Oberfl{\"a}chenpunkten aus einem hohen pr{\"u}ftechnischen Aufwand. Die laserbasierte, interferometrische Erfassung mechanischer Wellen ist gegen{\"u}ber Ultraschallsensoren rauschbehaftet und vergleichsweise unsensibel. Als wesentliche Voraussetzung der scannenden Anwendung von Laser-Ultraschall auf zementgebundene Baustoffe erfolgen systematische experimentelle Untersuchungen zur laserinduzierten ablativen Anregung. Diese sollen zum Verst{\"a}ndnis des Anregungsmechanismus unmittelbar auf den Oberfl{\"a}chen von zementgebundenen Baustoffen, Gesteinsk{\"o}rnungen und metallischen Werkstoffen beitragen, relevante Einflussfaktoren aus den charakteristischen Materialeigenschaften identifizieren, geeignete Prozessparameter gewinnen und die Verfahrensgrenzen aufzeigen. Unter Einsatz von Longitudinalwellen erfolgt die Anwendung von Laser-Ultraschall zur zeit- und ortsaufgel{\"o}sten Charakterisierung der Strukturbildung und Homogenit{\"a}t frischer sowie erh{\"a}rteter Proben zementgebundener Baustoffe. W{\"a}hrend der Strukturbildung wird erstmals eine simultane ber{\"u}hrungslose Erfassung von Longitudinal- und Scherwellen vorgenommen. Unter Anwendung von tomographischen Methoden (2D-Laufzeit¬tomo¬graphie) werden {\"u}berlagerungsfreie Informationen zur r{\"a}umlichen Verteilung struktureller Gef{\"u}gever{\"a}nderungen anhand der longitudinalen Ausbreitungsgeschwindigkeit bzw. des relativen dynamischen Elastizit{\"a}tsmoduls innerhalb von virtuellen Schnittebenen gesch{\"a}digter Probek{\"o}rper gewonnen. Als beton-sch{\"a}digende Mechanismen werden exemplarisch der kombinierte Frost-Tausalz-Angriff sowie die Alkali-Kiesels{\"a}ure-Reaktion (AKR) herangezogen. Die im Rahmen dieser Arbeit entwickelten Verfahren der zerst{\"o}rungsfreien Pr{\"u}fung bieten erweiterte M{\"o}glichkeiten zur Charakterisierung zementgebundener Baustoffe und deren strukturellen Ver{\"a}nderungen und lassen sich zielgerichtet in der Werkstoffentwicklung, bei der Qualit{\"a}tssicherung sowie zur Analyse von Schadensprozessen und -ursachen einsetzen.},
  subject      = {Beton},
  language  = {de}
}
@article{MosaviNajafiFaizollahzadehArdabilietal.,
  author    = {Mosavi, Amir and Najafi, Bahman and Faizollahzadeh Ardabili, Sina and Shamshirband, Shahaboddin and Rabczuk, Timon},
  title     = {An Intelligent Artificial Neural Network-Response Surface Methodology Method for Accessing the Optimum Biodiesel and Diesel Fuel Blending Conditions in a Diesel Engine from the Viewpoint of Exergy and Energy Analysis},
  series = {Energies},
  volume    = {2018},
  journal   = {Energies},
  number    = {11, 4},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/en11040860},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20180507-37467},
  pages     = {18},
  abstract  = {Biodiesel, as the main alternative fuel to diesel fuel which is produced from renewable and available resources, improves the engine emissions during combustion in diesel engines. In this study, the biodiesel is produced initially from waste cooking oil (WCO). The fuel samples are applied in a diesel engine and the engine performance has been considered from the viewpoint of exergy and energy approaches. Engine tests are performed at a constant 1500 rpm speed with various loads and fuel samples. The obtained experimental data are also applied to develop an artificial neural network (ANN) model. Response surface methodology (RSM) is employed to optimize the exergy and energy efficiencies. Based on the results of the energy analysis, optimal engine performance is obtained at 80\% of full load in presence of B10 and B20 fuels. However, based on the exergy analysis results, optimal engine performance is obtained at 80\% of full load in presence of B90 and B100 fuels. The optimum values of exergy and energy efficiencies are in the range of 25-30\% of full load, which is the same as the calculated range obtained from mathematical modeling.},
  subject      = {Biodiesel},
  language  = {en}
}
@inproceedings{DokhanchiArnoldVogeletal.,
  author    = {Dokhanchi, Najmeh Sadat and Arnold, J{\"o}rg and Vogel, Albert and V{\"o}lker, Conrad},
  title     = {Acoustic Travel-Time Tomography: Optimal Positioning of Transceiver and Maximal Sound-Ray Coverage of the Room},
  series = {Fortschritte der Akustik - DAGA 2019},
  booktitle = {Fortschritte der Akustik - DAGA 2019},
  doi       = {10.25643/bauhaus-universitaet.3877},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20190408-38778},
  pages     = {4},
  abstract  = {Acoustic travel-time tomography (ATOM) determines the distribution of the temperature in a propagation medium by measuring the travel-time of acoustic signals between transmitters and receivers. To employ ATOM for indoor climate measurements, the impulse responses have been measured in the climate chamber lab of the Bauhaus-University Weimar and compared with the theoretical results of its image source model (ISM). A challenging task is distinguishing the reflections of interest in the reflectogram when the sound rays have similar travel-times. This paper presents a numerical method to address this problem by finding optimal positions of transmitter and receiver, since they have a direct impact on the distribution of travel times. These optimal positions have the minimum number of simultaneous arrival time within a threshold level. Moreover, for the tomographic reconstruction, when some of the voxels remain empty of sound-rays, it leads to inaccurate determination of the air temperature within those voxels. Based on the presented numerical method, the number of empty tomographic voxels are minimized to ensure the best sound-ray coverage of the room. Subsequently, a spatial temperature distribution is estimated by simultaneous iterative reconstruction technique (SIRT). The experimental set-up in the climate chamber verifies the simulation results.},
  subject      = {Bauphysik},
  language  = {en}
}