@article{HarirchianKumariJadhavetal.,
  author    = {Harirchian, Ehsan and Kumari, Vandana and Jadhav, Kirti and Rasulzade, Shahla and Lahmer, Tom and Raj Das, Rohan},
  title     = {A Synthesized Study Based on Machine Learning Approaches for Rapid Classifying Earthquake Damage Grades to RC Buildings},
  series = {Applied Sciences},
  volume    = {2021},
  journal   = {Applied Sciences},
  number    = {Volume 11, issue 16, article 7540},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/app11167540},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210818-44853},
  pages     = {1 -- 33},
  abstract  = {A vast number of existing buildings were constructed before the development and enforcement of seismic design codes, which run into the risk of being severely damaged under the action of seismic excitations. This poses not only a threat to the life of people but also affects the socio-economic stability in the affected area. Therefore, it is necessary to assess such buildings' present vulnerability to make an educated decision regarding risk mitigation by seismic strengthening techniques such as retrofitting. However, it is economically and timely manner not feasible to inspect, repair, and augment every old building on an urban scale. As a result, a reliable rapid screening methods, namely Rapid Visual Screening (RVS), have garnered increasing interest among researchers and decision-makers alike. In this study, the effectiveness of five different Machine Learning (ML) techniques in vulnerability prediction applications have been investigated. The damage data of four different earthquakes from Ecuador, Haiti, Nepal, and South Korea, have been utilized to train and test the developed models. Eight performance modifiers have been implemented as variables with a supervised ML. The investigations on this paper illustrate that the assessed vulnerability classes by ML techniques were very close to the actual damage levels observed in the buildings.},
  subject      = {Maschinelles Lernen},
  language  = {en}
}
@article{MeiabadiMoradiKaramimoghadametal.,
  author    = {Meiabadi, Mohammad Saleh and Moradi, Mahmoud and Karamimoghadam, Mojtaba and Ardabili, Sina and Bodaghi, Mahdi and Shokri, Manouchehr and Mosavi, Amir Hosein},
  title     = {Modeling the Producibility of 3D Printing in Polylactic Acid Using Artificial Neural Networks and Fused Filament Fabrication},
  series = {polymers},
  volume    = {2021},
  journal   = {polymers},
  number    = {Volume 13, issue 19, article 3219},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/polym13193219},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220110-45518},
  pages     = {1 -- 21},
  abstract  = {Polylactic acid (PLA) is a highly applicable material that is used in 3D printers due to some significant features such as its deformation property and affordable cost. For improvement of the end-use quality, it is of significant importance to enhance the quality of fused filament fabrication (FFF)-printed objects in PLA. The purpose of this investigation was to boost toughness and to reduce the production cost of the FFF-printed tensile test samples with the desired part thickness. To remove the need for numerous and idle printing samples, the response surface method (RSM) was used. Statistical analysis was performed to deal with this concern by considering extruder temperature (ET), infill percentage (IP), and layer thickness (LT) as controlled factors. The artificial intelligence method of artificial neural network (ANN) and ANN-genetic algorithm (ANN-GA) were further developed to estimate the toughness, part thickness, and production-cost-dependent variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid machine learning (ML) technique could enhance the accuracy of modeling by about 7.5, 11.5, and 4.5\% for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. On the other hand, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which enables the usability of printed PLA objects.},
  subject      = {3D-Druck},
  language  = {en}
}