@article{FaizollahzadehArdabiliNajafiAlizamiretal.,
  author    = {Faizollahzadeh Ardabili, Sina and Najafi, Bahman and Alizamir, Meysam and Mosavi, Amir and Shamshirband, Shahaboddin and Rabczuk, Timon},
  title     = {Using SVM-RSM and ELM-RSM Approaches for Optimizing the Production Process of Methyl and Ethyl Esters},
  series = {Energies},
  journal   = {Energies},
  number    = {11, 2889},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/en11112889},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20181025-38170},
  pages     = {1 -- 20},
  abstract  = {The production of a desired product needs an effective use of the experimental model. The present study proposes an extreme learning machine (ELM) and a support vector machine (SVM) integrated with the response surface methodology (RSM) to solve the complexity in optimization and prediction of the ethyl ester and methyl ester production process. The novel hybrid models of ELM-RSM and ELM-SVM are further used as a case study to estimate the yield of methyl and ethyl esters through a trans-esterification process from waste cooking oil (WCO) based on American Society for Testing and Materials (ASTM) standards. The results of the prediction phase were also compared with artificial neural networks (ANNs) and adaptive neuro-fuzzy inference system (ANFIS), which were recently developed by the second author of this study. Based on the results, an ELM with a correlation coefficient of 0.9815 and 0.9863 for methyl and ethyl esters, respectively, had a high estimation capability compared with that for SVM, ANNs, and ANFIS. Accordingly, the maximum production yield was obtained in the case of using ELM-RSM of 96.86\% for ethyl ester at a temperature of 68.48 °C, a catalyst value of 1.15 wt. \%, mixing intensity of 650.07 rpm, and an alcohol to oil molar ratio (A/O) of 5.77; for methyl ester, the production yield was 98.46\% at a temperature of 67.62 °C, a catalyst value of 1.1 wt. \%, mixing intensity of 709.42 rpm, and an A/O of 6.09. Therefore, ELM-RSM increased the production yield by 3.6\% for ethyl ester and 3.1\% for methyl ester, compared with those for the experimental data.},
  subject      = {Biodiesel},
  language  = {en}
}
@article{MosaviNajafiFaizollahzadehArdabilietal.,
  author    = {Mosavi, Amir and Najafi, Bahman and Faizollahzadeh Ardabili, Sina and Shamshirband, Shahaboddin and Rabczuk, Timon},
  title     = {An Intelligent Artificial Neural Network-Response Surface Methodology Method for Accessing the Optimum Biodiesel and Diesel Fuel Blending Conditions in a Diesel Engine from the Viewpoint of Exergy and Energy Analysis},
  series = {Energies},
  volume    = {2018},
  journal   = {Energies},
  number    = {11, 4},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/en11040860},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20180507-37467},
  pages     = {18},
  abstract  = {Biodiesel, as the main alternative fuel to diesel fuel which is produced from renewable and available resources, improves the engine emissions during combustion in diesel engines. In this study, the biodiesel is produced initially from waste cooking oil (WCO). The fuel samples are applied in a diesel engine and the engine performance has been considered from the viewpoint of exergy and energy approaches. Engine tests are performed at a constant 1500 rpm speed with various loads and fuel samples. The obtained experimental data are also applied to develop an artificial neural network (ANN) model. Response surface methodology (RSM) is employed to optimize the exergy and energy efficiencies. Based on the results of the energy analysis, optimal engine performance is obtained at 80\% of full load in presence of B10 and B20 fuels. However, based on the exergy analysis results, optimal engine performance is obtained at 80\% of full load in presence of B90 and B100 fuels. The optimum values of exergy and energy efficiencies are in the range of 25-30\% of full load, which is the same as the calculated range obtained from mathematical modeling.},
  subject      = {Biodiesel},
  language  = {en}
}
@article{MeiabadiMoradiKaramimoghadametal.,
  author    = {Meiabadi, Mohammad Saleh and Moradi, Mahmoud and Karamimoghadam, Mojtaba and Ardabili, Sina and Bodaghi, Mahdi and Shokri, Manouchehr and Mosavi, Amir Hosein},
  title     = {Modeling the Producibility of 3D Printing in Polylactic Acid Using Artificial Neural Networks and Fused Filament Fabrication},
  series = {polymers},
  volume    = {2021},
  journal   = {polymers},
  number    = {Volume 13, issue 19, article 3219},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/polym13193219},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220110-45518},
  pages     = {1 -- 21},
  abstract  = {Polylactic acid (PLA) is a highly applicable material that is used in 3D printers due to some significant features such as its deformation property and affordable cost. For improvement of the end-use quality, it is of significant importance to enhance the quality of fused filament fabrication (FFF)-printed objects in PLA. The purpose of this investigation was to boost toughness and to reduce the production cost of the FFF-printed tensile test samples with the desired part thickness. To remove the need for numerous and idle printing samples, the response surface method (RSM) was used. Statistical analysis was performed to deal with this concern by considering extruder temperature (ET), infill percentage (IP), and layer thickness (LT) as controlled factors. The artificial intelligence method of artificial neural network (ANN) and ANN-genetic algorithm (ANN-GA) were further developed to estimate the toughness, part thickness, and production-cost-dependent variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid machine learning (ML) technique could enhance the accuracy of modeling by about 7.5, 11.5, and 4.5\% for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. On the other hand, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which enables the usability of printed PLA objects.},
  subject      = {3D-Druck},
  language  = {en}
}