@inproceedings{LutherKoenke, author = {Luther, Torsten and K{\"o}nke, Carsten}, title = {INVESTIGATION OF CRACK GROWTH IN POLYCRYSTALLINE MESOSTRUCTURES}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2988}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29886}, pages = {11}, abstract = {The design and application of high performance materials demands extensive knowledge of the materials damage behavior, which significantly depends on the meso- and microstructural complexity. Numerical simulations of crack growth on multiple length scales are promising tools to understand the damage phenomena in complex materials. In polycrystalline materials it has been observed that the grain boundary decohesion is one important mechanism that leads to micro crack initiation. Following this observation the paper presents a polycrystal mesoscale model consisting of grains with orthotropic material behavior and cohesive interfaces along grain boundaries, which is able to reproduce the crack initiation and propagation along grain boundaries in polycrystalline materials. With respect to the importance of modeling the geometry of the grain structure an advanced Voronoi algorithm is proposed to generate realistic polycrystalline material structures based on measured grain size distribution. The polycrystal model is applied to investigate the crack initiation and propagation in statically loaded representative volume elements of aluminum on the mesoscale without the necessity of initial damage definition. Future research work is planned to include the mesoscale model into a multiscale model for the damage analysis in polycrystalline materials.}, subject = {Architektur }, language = {en} } @inproceedings{Loemker, author = {L{\"o}mker, Thorsten Michael}, title = {SOLVING REVITALIZATION-PROBLEMS BY THE USE OF A CONSTRAINT PROGRAMING LANGUAGE}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2987}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29874}, pages = {13}, abstract = {This research focuses on an approach to describe principles in architectural layout planning within the domain of revitalization. With the aid of mathematical rules, which are executed by a computer, solutions to design problems are generated. Provided that "design" is in principle a combinatorial problem, i.e. a constraint-based search for an overall optimal solution of a problem, an exemplary method will be described to solve such problems in architectural layout planning. To avoid conflicts relating to theoretical subtleness, a customary approach adopted from Operations Research has been chosen in this work. In this approach, design is a synonym for planning, which could be described as a systematic and methodical course of action for the analysis and solution of current or future problems. The planning task is defined as an analysis of a problem with the aim to prepare optimal decisions by the use of mathematical methods. The decision problem of a planning task is represented by an optimization model and the application of an efficient algorithm in order to aid finding one or more solutions to the problem. The basic principle underlying the approach presented herein is the understanding of design in terms of searching for solutions that fulfill specific criteria. This search is executed by the use of a constraint programming language.}, subject = {Architektur }, language = {en} } @inproceedings{LourensvanRooyen, author = {Lourens, Eliz-Mari and van Rooyen, G.C.}, title = {Automating Preliminary Column Force Calculations In Multy-Storey Buildings}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2986}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29864}, pages = {10}, abstract = {In civil engineering practice, values of column forces are often required before any detailed analysis of the structure has been performed. One of the reasons for this arises from the fast-tracked nature of the majority of construction projects: foundations are laid and base columns constructed whilst analysis and design are still in progress. A need for quick results when feasibility studies are performed or when evaluating the effect of design changes on supporting columns form other situations in which column forces are required, but where a detailed analysis to get these forces seems superfluous. Thus it was concluded that the development of an efficient tool for column force calculations, in which the extensive input required in a finite element analysis is to be avoided, would be highly beneficial. The automation of the process is achieved by making use of a Voronoi diagram. The Voronoi diagram is used a) for subdividing the floor into influence areas and b) as a basis for automatic load assignment. The implemented procedure is integrated into a CAD system in which the relevant geometric information of the floor, i.e. its shape and column layout, can be defined or uploaded. A brief description of the implementation is included. Some comparative results and considerations regarding the continuation of the study are given.}, subject = {Architektur }, language = {en} } @inproceedings{StoimenovaLinsDatchevaetal., author = {Stoimenova, Eugenia and Lins, Yvonne and Datcheva, Maria and Schanz, Tom}, title = {INVERSE MODELLING OF SOIL HYDRAULIC CHARACTERISTIC FUNCTIONS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2985}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29858}, pages = {12}, abstract = {In this paper we evaluate 2D models for soil-water characteristic curve (SWCC), that incorporate the hysteretic nature of the relationship between volumetric water content θ and suction ψ. The models are based on nonlinear least squares estimation of the experimental data for sand. To estimate the dependent variable θ the proposed models include two independent variables, suction and sensors reading position (depth d in the column test). The variable d represents not only the position where suction and water content are measured but also the initial suction distribution before each of the hydraulic loading test phases. Due to this the proposed 2D regression models acquire the advantage that they: (a) can be applied for prediction of θ for any position along the column and (b) give the functional form for the scanning curves.}, subject = {Architektur }, language = {en} } @inproceedings{LehnerHartmann, author = {Lehner, Karlheinz and Hartmann, Dietrich}, title = {USING INTERVAL ANALYSIS FOR STRUCTURAL ENGINEERING PROBLEMS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2984}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29844}, pages = {10}, abstract = {Interval analysis extends the concept of computing with real numbers to computing with real intervals. As a consequence, some interesting properties appear, such as the delivery of guaranteed results or confirmed global values. The former property is given in the sense that unknown numerical values are in known to lie in a computed interval. The latter property states that the global minimum value, for example, of a given function is also known to be contained in a interval (or a finite set of intervals). Depending upon the amount computation effort invested in the calculation, we can often find tight bounds on these enclosing intervals. The downside of interval analysis, however, is the mathematically correct, but often very pessimistic size of the interval result. This is in particularly due to the so-called dependency effect, where a single variable is used multiple times in one calculation. Applying interval analysis to structural analysis problems, the dependency has a great influence on the quality of numerical results. In this paper, a brief background of interval analysis is presented and shown how it can be applied to the solution of structural analysis problems. A discussion of possible improvements as well as an outlook to parallel computing is also given.}, subject = {Architektur }, language = {en} } @inproceedings{Kravchenko, author = {Kravchenko, Vladislav}, title = {NEW APPLICATIONS OF PSEUDOANALYTIC FUNCTION THEORY}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2983}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29835}, pages = {3}, abstract = {We show a close relation between the Schr{\"o}dinger equation and the conductivity equation to a Vekua equation of a special form. Under quite general conditions we propose an algorithm for explicit construction of pseudoanalytic positive formal powers for the Vekua equation that as a consequence gives us a complete system of solutions for the Schr{\"o}dinger and the conductivity equations. Besides the construction of complete systems of exact solutions for the above mentioned second order equations and the Dirac equation, we discuss some other applications of pseudoanalytic function theory.}, subject = {Architektur }, language = {en} } @inproceedings{Krasnov, author = {Krasnov, Yakov}, title = {ANALYTIC FUNCTIONS IN OPERATOR VARIABLES AS SOLUTION TO PDES}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2982}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29822}, pages = {16}, abstract = {Procedures of a construction of general solutions for some classes of partial differential equations (PDEs) are proposed and a symmetry operators approach to the raising the orders of the polynomial solutions to linear PDEs are develops. We touch upon an ''operator analytic function theory'' as the solution of a frequent classes of the equations of mathematical physics, when its symmetry operators forms vast enough space. The MAPLE© package programs for the building the operator variables is elaborated also.}, subject = {Architektur }, language = {en} } @inproceedings{KoenigTauscher, author = {K{\"o}nig, Markus and Tauscher, Eike}, title = {BERECHNUNG VON BAUABL{\"A}UFEN MIT VERSCHIEDENEN AUSF{\"U}HRUNGSVARIANTEN}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2981}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29816}, pages = {11}, abstract = {Prozesse im Bauingenieurwesen sind komplex und beinhalten eine große Anzahl verschiedener Aufgaben mit vielen logischen Abh{\"a}ngigkeiten. Basierend auf diesen projektspezifischen Abh{\"a}ngigkeiten wird gew{\"o}hnlich ein Bauablaufplan manuell erstellt. In der Regel existieren mehrere Varianten und somit alternative Bauabl{\"a}ufe um ein Projekt zu realisieren. Welche dieser Ausf{\"u}hrungsvarianten zur praktischen Anwendung kommt, wird durch den jeweiligen Projektmanager bestimmt. Falls {\"A};nderungen oder St{\"o}rungen w{\"a}hrend des Bauablaufs auftreten, m{\"u}ssen die davon betroffenen Aufgaben und Abl{\"a}ufe per Hand modifiziert und alternative Aufgaben sowie Abl{\"a}ufe stattdessen ausgef{\"u}hrt werden. Diese Vorgehensweise ist oft sehr aufw{\"a}ndig und teuer. Aktuelle Forschungsans{\"a}tze besch{\"a}ftigen sich mit der automatischen Generierung von Bauabl{\"a}ufen. Grundlage sind dabei Aufgaben mit ihren erforderlichen Voraussetzungen und erzeugten Ergebnissen. Im Rahmen dieses Beitrags wird eine Methodik vorgestellt, um Bauabl{\"a}ufe mit Ausf{\"u}hrungsvarianten in Form von Workflow-Netzen zu jeder Zeit berechnen zu k{\"o}nnen. Die vorgestellte Methode wird anhand eines Beispiels aus dem Straßenbau schematisch dargestellt.}, subject = {Architektur }, language = {de} } @inproceedings{KoenigLang, author = {K{\"o}nig, Markus and Lang, H.}, title = {ANWENDUNG DES CASE-BASED REASONING BEI DER ERMITTLUNG VON VARIANTEN F{\"u}R DEN OBERBAU VON VERKEHRSFL{\"A}CHEN}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2980}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29808}, pages = {9}, abstract = {F{\"u}r die Ausf{\"u}hrung des Oberbaus von Verkehrsfl{\"a}chen existiert in Abh{\"a}ngigkeit von projektspezifischen Voraussetzungen eine Vielzahl von verschiedenen Varianten. Aufgrund von Erfahrungen der Projektplaner werden bei {\"a}hnlichen Voraussetzungen h{\"a}ufig gleichartige Ausf{\"u}hrungsvarianten gew{\"a}hlt. Um eine m{\"o}gliche L{\"o}sungsvariante f{\"u}r den Straßenoberbau zu erhalten, sollten daher nicht nur die gesetzlichen Richtlinien sondern auch bereits beendete Projekte ber{\"u}cksichtigt werden. Im Rahmen eines Wissenschaftlichen Kollegs an der Bauhaus-Universit{\"a}t Weimar wurde die Anwendung des Case-Based Reasoning f{\"u}r die Auswahl von Ausf{\"u}hrungsvarianten f{\"u}r den Straßenoberbau untersucht. In diesem Beitrag werden die grundlegenden Konzepte des Case-Based Reasoning und die Bestimmung von {\"a}hnlichen Varianten anhand einfacher Beispiele aus dem Straßenoberbau dargestellt.}, subject = {Architektur }, language = {de} } @inproceedings{Knyziak, author = {Knyziak, Piotr}, title = {ANALYSIS THE TECHNICAL STATE FOR LARGE-PANEL RESIDENTIAL BUILDINGS BEHIND ASSISTANCE OF ARTIFICIAL NEURAL NETWORKS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2979}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29792}, pages = {9}, abstract = {This paper presents two new methods for analysis of a technical state of large-panel residential buildings. The first method is based on elements extracted from the classical methods and on data about repairs and modernization collected from building documentations. The technical state of a building is calculated as a sum of several groups of elements defining the technical state. The deterioration in this method depends on: - time, which has passed since last repair of element or time which has passed since construction, - estimate of the state of element groups which can be determined on basis of yearly controls. This is a new unique method. it is easy to use, does not need expertise. The required data could be extracted easily from building documentations. For better accuracy the data from building inspections should be applied (in Poland inspections are made every year). The second method is based on the extracted data processing by means of the artificial neural networks. The aim is to learn the artificial neural network configurations for a set of data containing values of the technical state and information about building repairs for last years (or other information and building parameters) and next to analyse new buildings by the instructed neural network. The second profit from using artificial neural networks is the reduction of number of parameters. Instead of more then 40 parameters describing building, about 6-12 are usually sufficient for satisfactory accuracy. This method could have lower accuracy but it is less prone to data errors.}, subject = {Architektur }, language = {en} } @inproceedings{KnauerDammeierMeffert, author = {Knauer, Uwe and Dammeier, T. and Meffert, Beate}, title = {THE STRUCTURE OF ROAD TRAFFIC SCENES AS REVEALED BY UNSUPERVISED ANALYSIS OF THE TIME AVERAGED OPTICAL FLOW}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2978}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29780}, pages = {9}, abstract = {The Lucas-Kanade tracker has proven to be an efficient and accurate method for calculation of the optical flow. However, this algorithm can reliably track only suitable image features like corners and edges. Therefore, the optical flow can only be calculated for a few points in each image, resulting in sparse optical flow fields. Accumulation of these vectors over time is a suitable method to retrieve a dense motion vector field. However, the accumulation process limits application of the proposed method to fixed camera setups. Here, a histogram based approach is favored to allow more than a single typical flow vector per pixel. The resulting vector field can be used to detect roads and prescribed driving directions which constrain object movements. The motion structure can be modeled as a graph. The nodes represent entry and exit points for road users as well as crossings, while the edges represent typical paths.}, subject = {Architektur }, language = {en} } @inproceedings{Klingert, author = {Klingert, Maik}, title = {THE USAGE OF IMAGE PROCESSING METHODS FOR INTERPRETATION OF THERMOGRAPHY DATA}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2977}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29777}, pages = {13}, abstract = {For assessment of old buildings, thermal graphic analysis aided with infra-red camera have been employed in a wide range nowadays. Image processing and evaluation can be economically practicable only if the image evaluation can also be automated to the largest extend. For that reason methods of computer vision are presented in this paper to evaluate thermal images. To detect typical thermal image elements, such as thermal bridges and lintels in thermal images respectively gray value images, methods of digital image processing have been applied, of which numerical procedures are available to transform, modify and encode images. At the same time, image processing can be regarded as a multi-stage process. In order to be able to accomplish the process of image analysis from image formation through perfecting and segmentation to categorization, appropriate functions must be implemented. For this purpose, different measuring procedures and methods for automated detection and evaluation have been tested.}, subject = {Architektur }, language = {en} } @inproceedings{KlawitterOstrowski, author = {Klawitter, Arne and Ostrowski, M.}, title = {INTEGRATED RAINFALL RUNOFF MODELLING IN SMALL URBANIZED CATCHMENTS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2976}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29767}, pages = {12}, abstract = {A concept for integrated modeling of urban and rural hydrology is introduced. The concept allows for simulations on the catchment scale as well as on the local scale. It is based on a 2-layer-approach which facilitates the parallel coupling of a catchment hydrology model with an urban hydrology model, considering the interactions between the two systems. The concept has been implemented in a computer model combining a grid based distributed hydrological catchment model and a hydrological urban stormwater model based on elementary units. The combined model provides a flexible solution for time and spatial scale integration and offers to calculate separate water balances for urban and rural hydrology. Furthermore, it is GIS-based which allows for easy and accurate geo-referencing of urban overflow structures, which are considered as points of interactions between the two hydrologic systems. Due to the two-layer-approach, programs of measures can be incorporated in each system separately. The capabilities of the combined model have been tested on a hypothetical test case and a real world application. It could be shown that the model is capable of accurately quantifying the effects of urbanization in a catchment. The affects of urbanization can be analyzed at the catchment outlet, but can also be traced back to its origins, due to the geo-referencing of urban overflow structures. This is a mayor advantage over conventional hydrological catchment models for the analysis of land use changes.}, subject = {Architektur }, language = {en} } @inproceedings{Klauer, author = {Klauer, Thomas}, title = {MOBILE FACILITY MANAGEMENT ZUR INSPEKTION UND INSTANDHALTUNG VON INGENIEURBAUWERKEN}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2975}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29759}, pages = {10}, abstract = {In diesem Beitrag wird eine mobile Software-Komponente zur Vor-Ort-Unterst{\"u}tzung von Bauwerkspr{\"u}fungen gem{\"a}ß DIN 1076 „Ingenieurbauwerke im Zuge von Strassen und Wegen, {\"U}berwachung und Pr{\"u}fung" vorgestellt, welche sich im praktischen Einsatz bei der Hochbahn AG Hamburg befindet. Mit Hilfe dieses Werkzeugs kann die Aktivit{\"a}t am Bauwerk in den gesamten softwaregest{\"u}tzten Gesch{\"a}ftsprozess der auwerksinstandhaltung integriert und somit die Bearbeitungszeit einer Bauwerkspr{\"u}fung von der Vorbereitung bis zur Pr{\"u}fbericht-Erstellung reduziert werden. Die Technologie des Mobile Computing wird unter Ber{\"u}cksichtigung spezieller fachlicher Randbedingungen, wie z.B. dem Einsatzort unter freiem Himmel, erl{\"a}utert und es werden Methoden zur effizienten Datenerfassung mit Stift und Sprache vorgestellt und bewertet. Ferner wird die Einschr{\"a}nkung der Hardware durch die geringere Gr{\"o}ße der Endger{\"a}te, die sich durch die Bedingung der Mobilit{\"a}t ergibt, untersucht.}, subject = {Architektur }, language = {de} } @inproceedings{Kisil, author = {Kisil, Vladimir}, title = {FILLMORE-SPRINGER-CNOPS CONSTRUCTION IMPLEMENTED IN GINAC}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2974}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29744}, pages = {103}, abstract = {This is an implementation of the Fillmore-Springer-Cnops construction (FSCc) based on the Clifford algebra capacities of the GiNaC computer algebra system. FSCc linearises the linear-fraction action of the Mobius group. This turns to be very useful in several theoretical and applied fields including engineering. The core of this realisation of FSCc is done for an arbitrary dimension, while a subclass for two dimensional cycles add some 2D-specific routines including a visualisation to PostScript files through the MetaPost or Asymptote software. This library is a backbone of many result published in, which serve as illustrations of its usage. It can be ported (with various level of required changes) to other CAS with Clifford algebras capabilities.}, subject = {Architektur }, language = {en} } @inproceedings{KimuraMakinoMaegaitoetal., author = {Kimura, Atsushi and Makino, Y. and Maegaito, Kentaro and Suzuki, Osamu}, title = {ITERATION DYNAMICAL SYSTEMS OF DISCRETE LAPLACIANS ON THE PLANE LATTICE (II) (THE VISUAL IMPRESSIONS GIVEN BY DESIGN-PATTERNS)}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2973}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29731}, pages = {4}, abstract = {The present study was designed to investigate the underlying factors determining the visual impressions of design-patterns that have complex textures. Design-patterns produced by "the dynamical system defined by iterations of discrete Laplacians on the plane lattice" were adopted as stimuli because they were not only complex, but also defined mathematically. In the experiment, 21 graduate and undergraduate students sorted 102 design-patterns into several groups by visual impressions. Those 102 patterns were classified into 12 categories by the cluster analysis. The results showed that the regularity of pattern was a most efficient factor for determining visual impressions of design-pattern, and there were some correspondence between visual impressions and mathematical variables of design-pattern. Especially, the visual impressions were influenced greatly by the neighborhood, and less influenced by steps of iterations.}, subject = {Architektur }, language = {en} } @inproceedings{Kasparek, author = {Kasparek, Eva}, title = {CONVERGENCE OF A NEW CONSISTENT FOLDED PLATE THEORY}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2972}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29724}, pages = {10}, abstract = {The design of challenging space structures frequently relies on the theory of folded plates. The models are composed of plane facets of which the bending and membrane stiffness are coupled along the folds. In conventional finite element analysis of faceted structures the continuity of the displacement field is enforced exclusively at the nodes. Since approximate solutions for transverse and for in-plane displacements are not members of the same function space, separation occurs in between the common nodes of adjacent elements. It is shown that the kinematic assumptions of Bernoulli are accounted for this incompatibility along the edges in facet models. A general answer to this problem involves substantial modification of plate and membrane theory, but a straight forward formulation can be derived for simply folded plates, structures, whose folds do not intersect. A broad class of faceted structures, including models of various curved shells, belong to this category and can be calculated consistently. The additional requirements to assure continuity concern the mapping of displacement derivatives on the edges. An appropriate finite facet element provides node and edge-oriented degrees of freedom, whose transformation to system degrees of freedom, depends on the geometric configuration at each node. The concept is implemented using conform triangular elements. To evaluate the new approach, the energy norm of representative structures for refined meshes is calculated. The focus is placed on the mathematical convergence towards reliable solutions obtained from finite volume models.}, subject = {Architektur }, language = {en} } @inproceedings{Jahnke, author = {Jahnke, Georg}, title = {HISTORISCHE BAUSUBSTANZ IN MECKLENBURG}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2971}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29719}, pages = {11}, abstract = {Mit diesen Ausf{\"u}hrungen wird ein Beitrag zum weiteren Erhalt der historischen Bausubstanz in Mecklenburg aus der Sicht der Tragwerksanalyse geleistet. Dabei best{\"a}tigt es sich immer mehr, dass mit dem Modell der Geometrie, der Belastung und des Materials gleichberechtigte Modelle f{\"u}r eine wirklichkeitsnahe Einsch{\"a}tzung des Tragverhaltens eines Tragwerks vorliegen m{\"u}ssen. Es zeigt sich, dass dabei die besten Berechnungsprogramme nur die Ergebnisse liefern k{\"o}nnen, die mit den Eingabedaten zu erzielen sind. So hat sich der Forschungsschwerpunkt im Lehrgebiet Tragwerkslehre des FB Architektur an der Hochschule Wismar in den letzten Jahren auf die realistische Abbildung der Wechselwirkung zwischen der Bauaufnahme und der geometrischen Modellierung konzentriert. In diesem Bereich zeigen sich als Schwerpunkte die Wechselwirkung zwischen Sch{\"a}den und Tragwerksanalyse und die Wechselwirkung zwischen der aufgenommenen Geometrie und dem geometrischen Modell f{\"u}r die Tragwerksanalyse. Die F{\"u}lle der aufgenommenen Daten sind dabei in der Regel mehr hinderlich als ein Segen f{\"u}r die Tragwerksanalyse. Hier wurde gezeigt, welche und wie viele geometrische Daten f{\"u}r das geometrische Modell f{\"u}r die Tragwerksanalyse sinnvoll sind. Da die eigene Datenaufnahme relativ viel Zeit beansprucht, wurde eine "geistige" Bauaufnahme durchgef{\"u}hrt. Dazu wird der historische Planungsprozess in den einzelnen Formfindungsschritten nachvollzogen und in die virtuelle Realit{\"a}t {\"u}berf{\"u}hrt. Mit dieser Methode ergeben sich unterschiedliche Bauzust{\"a}nde und es lassen sich auch m{\"o}gliche Bauphasen abbilden. Die Tragwerksanalyse dieser virtuellen Realit{\"a}t zeigt dann m{\"o}gliche Schw{\"a}chen der Tragwerke und/oder die Notwendigkeit konstruktiver Ver{\"a}nderungen. Ein Vergleich der Ergebnisse der Tragwerksanalyse mit der Realit{\"a}t anhand des vorliegenden Datenbestands liefert die Grundlage f{\"u}r den aktuellen Handlungsbedarf. Da der Bauzustand eines Bauwerkes unter einer zeitlichen Ver{\"a}nderung steht, werden Methoden {\"u}berpr{\"u}ft, die es erm{\"o}glichen, einen einmal vorgelegten Datenbestand aufzubereiten und weiter zu verwalten.}, subject = {Architektur }, language = {de} } @inproceedings{HoffmannKornadt, author = {Hoffmann, Sabine and Kornadt, Oliver}, title = {PHASEN{\"U}BERGANGSMATERIALIEN ALS PASSIVE W{\"A}RMESPEICHER IN REVITALISIERUNGSOBJEKTEN}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2969}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29699}, pages = {12}, abstract = {Summer overheating in buildings is a common problem, especially in office buildings with large glazed facades, high internal loads and low thermal mass. Phase change materials (PCM) that undergo a phase transition in the temperature range of thermal comfort can add thermal mass without increasing the structural load of the building. The investigated PCM were micro-encapsulated and mixed into gypsum plaster. The experiments showed a reduction of indoor-temperature of up to 4 K when using a 3 cm layer of PCM-plaster with micro-encapsulated paraffin. The measurement results could validate a numerical model that is based on a temperature dependent function for heat capacity. Thermal building simulation showed that a 3 cm layer of PCM-plaster can help to fulfil German regulations concerning heat protection of buildings in summer for most office rooms.}, subject = {Architektur }, language = {de} } @inproceedings{HildebrandWudtkeWerner, author = {Hildebrand, J{\"o}rg and Wudtke, Idna and Werner, Frank}, title = {M{\"O}GLICHKEITEN DER MATHEMATISCHEN BESCHREIBUNG VON PHASENUMWANDLUNGEN IM STAHL BEI SCHWEIß- UND WIG-NACHBEHANDLUNGSPROZESSEN}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2968}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29684}, pages = {13}, abstract = {In the final decades many scientists were occupied intensively with the change of materials during a process and their mathematical descriptions. The extensive and extensive analyses were supported by the advanced computer science. A mathematical description of the phase transformation is a condition for a realistic FE simulation of the state of microstructure. It is possible to simulate the temperature and stress field also in complex construction based on the state of microstructure. In the last years a great number of mathematical models were expanded to describe the transformation between different phases. For the development of the models for transformation kinetics it is practical to subdivide into isothermal and non-isothermal processes according to the thermal conditions. Some models for the description of the transformation with non-isothermal processes represent extensions for isothermal of processes. A part of parameters for the describing equations can be derived from the time-temperature-transformation diagrams in the literature. Furthermore the two possibilities of transformation are considered by different models - diffusion controlled and not diffusion controlled. The material-specific characteristics can be simulated during the transformation for each individual phase in a realistic FE analyses. Also new materials can be simulated after a modification of the parameters in the describing equations for the phase transformation. The effects in the temperature and stress field are a substantial reason for the investigation of the phase transformation during the welding and TIG-dressing processes.}, subject = {Architektur }, language = {de} } @inproceedings{Heuer, author = {Heuer, Andreas}, title = {THREE-DIMENSIONAL MODELING OF CONCRETE WITH DAMAGE AND PLASTICITY}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2967}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29671}, pages = {15}, abstract = {The concrete is modeled as a material with damage and plasticity, whereat the viscoplastic and the viscoelastic behaviour depends on the rate of the total strains. Due to the damage behaviour the compliance tensor develops different properties in tension and compression. There have been tested various yield surfaces and flow rules, damage rules respectively to their usability in a concrete model. One three-dimensional yield surface was developed from a failure surface based on the Willam--Warnke five-parameter model by the author. Only one general uni-axial stress-strain-relation is used for the numeric control of the yield surface. From that curve all necessary parameters for different strengths of concrete and different strain rates can be derived by affine transformations. For the flow rule in the compression zone a non associated inelastic potential is used, in the tension zone a Rankine potential. Conditional on the time-dependent formulation, the symmetry of the system equations is maintained in spite of the usage of non-associated potentials for the derivation of the inelastic strains. In case of quasi statical computations a simple viscoplastic law is used that is rested on an approach to Perzyna. The principle of equality of dissipation power in the uni-axial and the three-axial state of stress is used. It is modified by a factor that depends on the actual stress ratio and in comparison with the Kupfer experiments it implicates strains that are more realistic. The implementation of the concrete model is conducted in a mixed hybrid finite element. Examples in the structural level are introduced for verification of the concrete model.}, subject = {Architektur }, language = {en} } @inproceedings{Heinrich, author = {Heinrich, Timo}, title = {KENNZEICHNUNGSBASIERTER ZUGRIFF VON PROZESSMODELLEN AUF OBJEKTBEST{\"A}NDE DES BAUWESENS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2966}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29669}, pages = {13}, abstract = {F{\"u}r eine beherrschbare Koordination und Durchf{\"u}hrung von Planungsaufgaben in Bauprojekten wird der Planungsprozess zunehmend in formalisierten Modellen - Prozessmodellen - beschrieben. Die Produktmodellforschung ihrerseits widmet sich der Speicherung von Planungsdaten in Form von objektorientierten Modellen im Rechner. Hauptaugenmerk sind dabei die Wahrung der Konsistenz und die Modellierung von Abh{\"a}ngigkeiten innerhalb dieses Planungsmaterials. Der Bezug zu den Akteuren der Planung wird nicht direkt hergestellt. Ein formal beschriebener Planungsprozesses kann in der Praxis noch nicht derart realisiert werden, dass ein Zugriff auf Einzelobjekte des Planungsprozesses gew{\"a}hrleistet ist. Bestehende Planungsunterst{\"u}tzungs- und Workflowmanagement-Systeme abstrahieren und ordnen das Planungsmaterial nach wie vor auf Dateiebene. Der vorliegende Artikel beschreibt eine Methode f{\"u}r die geeignete Verbindung von formalisierten Prozessmodellen in der Bauplanung mit den Einzelobjekten, die in den modellorientierten Objektmengen kodiert sind. Dabei wird die Zugeh{\"o}rigkeit bestimmter Objekte zu Pl{\"a}nen und Dokumenten (zum Zwecke des Datenaustauschs) nicht l{\"a}nger durch die physische Zuordnung zu Dateien festgelegt. Es wird ein formales Beschreibungsmittel vorgestellt, welches die entsprechende Teilmengenbildung aus der Gesamtheit der Planungsobjekte erm{\"o}glicht. F{\"u}r die bisherigen Formen des Datenaustausches werden aus den Objektmodellen der Planung Teilmengen herausgel{\"o}st und physikalisch zwischen den Planern transportiert. Das neue Beschreibungsmittel hingegen erlaubt es, die Bildungsvorschrift f{\"u}r Objektteilmengen statt der Mengen selbst zwischen den Planern auszutauschen. Der Zugriff auf die konkreten Objekte findet dann direkt modellbasiert statt.}, subject = {Architektur }, language = {de} } @inproceedings{HapurneNistor, author = {Hapurne, Tania Mariana and Nistor, S.}, title = {USING MODERN TECHNOLOGIES TO UPGRADE EDILITARY URBAN INFRASTRUCTURE}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2965}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29650}, pages = {6}, abstract = {Adopting the European laws concerning environmental protection will require sustained efforts of the authorities and communities from Romania; implementing modern solutions will become a fast and effective option for the improvement of the functioning systems, in order to prevent disasters. As a part of the urban infrastructure, the drainage networks of pluvial and residual waters are included in the plan of promoting the systems which protect the environmental quality, with the purpose of integrated and adaptive management. The paper presents a distributed control system for sewer network of Iasi town. Unsatisfactory technical state of the actual sewer system is exposed, focusing on objectives related to implementation of the control system. The proposed distributed control system of Iasi drainage network is based on the implementation of the hierarchic control theory for diagnose, sewer planning and management. There are proposed two control levels: coordinating and local execution. Configuration of the distributed control system, including data acquisition and conversion equipment, interface characteristics, local data bus, data communication network, station configuration are widely described. The project wish to be an useful instrument for the local authorities in the preventing and reducing the impact of future natural disasters over the urban areas by means of modern technologies.}, subject = {Architektur }, language = {en} } @inproceedings{HaefnerKesselKoenke, author = {H{\"a}fner, Stefan and Kessel, Marco and K{\"o}nke, Carsten}, title = {MULTIPHASE B-SPLINE FINITE ELEMENTS OF VARIABLE ORDER IN THE MECHANICAL ANALYSIS OF HETEROGENEOUS SOLIDS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2964}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29643}, pages = {37}, abstract = {Advanced finite elements are proposed for the mechanical analysis of heterogeneous materials. The approximation quality of these finite elements can be controlled by a variable order of B-spline shape functions. An element-based formulation is developed such that the finite element problem can iteratively be solved without storing a global stiffness matrix. This memory saving allows for an essential increase of problem size. The heterogeneous material is modelled by projection onto a uniform, orthogonal grid of elements. Conventional, strictly grid-based finite element models show severe oscillating defects in the stress solutions at material interfaces. This problem is cured by the extension to multiphase finite elements. This concept enables to define a heterogeneous material distribution within the finite element. This is possible by a variable number of integration points to each of which individual material properties can be assigned. Based on an interpolation of material properties at nodes and further smooth interpolation within the finite elements, a continuous material function is established. With both, continuous B-spline shape function and continuous material function, also the stress solution will be continuous in the domain. The inaccuracy implied by the continuous material field is by far less defective than the prior oscillating behaviour of stresses. One- and two-dimensional numerical examples are presented.}, subject = {Architektur }, language = {en} } @inproceedings{HaefnerKoenke, author = {H{\"a}fner, Stefan and K{\"o}nke, Carsten}, title = {DAMAGE SIMULATION OF HETEROGENEOUS SOLIDS BY NONLOCAL FORMULATIONS ON ORTHOGONAL GRIDS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2963}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29638}, pages = {15}, abstract = {The present paper is part of a comprehensive approach of grid-based modelling. This approach includes geometrical modelling by pixel or voxel models, advanced multiphase B-spline finite elements of variable order and fast iterative solver methods based on the multigrid method. So far, we have only presented these grid-based methods in connection with linear elastic analysis of heterogeneous materials. Damage simulation demands further considerations. The direct stress solution of standard bilinear finite elements is severly defective, especially along material interfaces. Besides achieving objective constitutive modelling, various nonlocal formulations are applied to improve the stress solution. Such a corrective data processing can either refer to input data in terms of Young's modulus or to the attained finite element stress solution, as well as to a combination of both. A damage-controlled sequentially linear analysis is applied in connection with an isotropic damage law. Essentially by a high resolution of the heterogeneous solid, local isotropic damage on the material subscale allows to simulate complex damage topologies such as cracks. Therefore anisotropic degradation of a material sample can be simulated. Based on an effectively secantial global stiffness the analysis is numerically stable. The iteration step size is controlled for an adequate simulation of the damage path. This requires many steps, but in the iterative solution process each new step starts with the solution of the prior step. Therefore this method is quite effective. The present paper provides an introduction of the proposed concept for a stable simulation of damage in heterogeneous solids.}, subject = {Architektur }, language = {en} } @inproceedings{HaefnerKoenke, author = {H{\"a}fner, Stefan and K{\"o}nke, Carsten}, title = {MULTIGRID PRECONDITIONED CONJUGATE GRADIENT METHOD IN THE MECHANICAL ANALYSIS OF HETEROGENEOUS SOLIDS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2962}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29626}, pages = {29}, abstract = {A fast solver method called the multigrid preconditioned conjugate gradient method is proposed for the mechanical analysis of heterogeneous materials on the mesoscale. Even small samples of a heterogeneous material such as concrete show a complex geometry of different phases. These materials can be modelled by projection onto a uniform, orthogonal grid of elements. As one major problem the possible resolution of the concrete specimen is generally restricted due to (a) computation times and even more critical (b) memory demand. Iterative solvers can be based on a local element-based formulation while orthogonal grids consist of geometrical identical elements. The element-based formulation is short and transparent, and therefore efficient in implementation. A variation of the material properties in elements or integration points is possible. The multigrid method is a fast iterative solver method, where ideally the computational effort only increases linear with problem size. This is an optimal property which is almost reached in the implementation presented here. In fact no other method is known which scales better than linear. Therefore the multigrid method gains in importance the larger the problem becomes. But for heterogeneous models with very large ratios of Young's moduli the multigrid method considerably slows down by a constant factor. Such large ratios occur in certain heterogeneous solids, as well as in the damage analysis of solids. As solution to this problem the multigrid preconditioned conjugate gradient method is proposed. A benchmark highlights the multigrid preconditioned conjugate gradient method as the method of choice for very large ratio's of Young's modulus. A proposed modified multigrid cycle shows good results, in the application as stand-alone solver or as preconditioner.}, subject = {Architektur }, language = {en} } @inproceedings{GurtovyTynchuk, author = {Gurtovy, O. G. and Tynchuk, S.O.}, title = {RESEARCH OF DEFORMATION OF MULTILAYERED PLATES ON UNDEFORMABLE BASIS BY UNFLEXURAL SPECIFIED MODEL}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2961}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29613}, pages = {6}, abstract = {Stress-strain state (SSS) of multilayered plates on undeformable foundation is investigated. The settlement circuit of transverse loaded plate is formed by symmetrical attaching of a plate concerning a surface of contact to the foundation. The plate of the double thickness becomes bilateral symmetrically loaded concerning its median surface. It allows to model only unflexural deformation that reduces amount of unknown and the general order of differentiation of resolving system of the equations. The developed refined continual model takes into account deformations of transverse shear and transverse compression in high iterative approximation. Rigid contact between the foundation and a plate, and also shear without friction on a surface of contact of a plate with the foundation is considered. Calculations confirm efficiency of such approach, allowing to receive decisions which is qualitative and quantitatively close to three-dimensional solutions.}, subject = {Architektur }, language = {en} } @inproceedings{GruberValdman, author = {Gruber, Peter and Valdman, J.}, title = {APPROXIMATE SOLUTION OF ELASTOPLASTIC PROBLEMS BASED ON THE MOREAU-YOSIDA THEOREM}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2960}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29602}, pages = {8}, abstract = {We propose a new approach to the numerical solution of quasi-static elastic-plastic problems based on the Moreau-Yosida theorem. After the time discretization, the problem is expressed as an energy minimization problem for unknown displacement and plastic strain fields. The dependency of the minimization functional on the displacement is smooth whereas the dependency on the plastic strain is non-smooth. Besides, there exists an explicit formula, how to calculate the plastic strain from a given displacement field. This allows us to reformulate the original problem as a minimization problem in the displacement only. Using the Moreau-Yosida theorem from the convex analysis, the minimization functional in the displacements turns out to be Frechet-differentiable, although the hidden dependency on the plastic strain is non-differentiable. The seconds derivative exists everywhere apart from the elastic-plastic interface dividing elastic and plastic zones of the continuum. This motivates to implement a Newton-like method, which converges super-linearly as can be observed in our numerical experiments.}, subject = {Architektur }, language = {en} } @inproceedings{Goettlicher, author = {G{\"o}ttlicher, Manfred}, title = {HYBRID SOLID-LIQUID MODEL FOR GRANULAR MATERIAL}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2959}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29596}, pages = {20}, abstract = {Solid behavior as well as liquid behavior characterizes the flow of granular material in silos. The presented model is based on an appropriate interaction of a displacement field and a velocity field. The constitutive equations and the applied algorithm are developed from the exact solution for a standard case. The standard case evolves from a very tall vertical plane strain silo containing material that flows at a constant speed. No horizontal displacements and velocities take place. No changes regarding the field values arise in the vertical direction and in time. Tension is not allowed at any point. Coulomb friction represents the effects of the vertical walls. The interaction between the flowing material and the walls is covered by a forced boundary condition resulting in an additional matrix for the solid component as well as for the liquid component. The resulting integral equations are designed to be solved directly. Three coefficients describe the properties of the granular material. They govern elastic solid behavior in combination with viscous liquid behavior.}, subject = {Architektur }, language = {de} } @inproceedings{GoebelHildebrandWerner, author = {G{\"o}bel, Michael and Hildebrand, J{\"o}rg and Werner, Frank}, title = {NUMERISCHES MODELL F{\"U}R DIE SIMULATION EINER LASERSTRAHLSCHWEIßUNG VON QUARZGLAS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2958}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29589}, pages = {14}, abstract = {Ausgehend von den fundierten Erfahrungen, die f{\"u}r das Schweißen von verschiedensten Metallen vorliegen, wird an der Professur Stahlbau der Bauhaus-Universit{\"a}t Weimar ein neuartiges Verfahren zum CO2-Laserstrahlschweißen von Quarzglas numerisch untersucht. Dabei kommt die kommerzielle FE-Software SYSWELD® zum Einsatz. Die erforderlichen Versuche werden in Zusammenarbeit mit dem Institut f{\"u}r F{\"u}getechnik und Werkstoffpr{\"u}fung GmbH aus Jena realisiert. Die numerische Analyse wird eingesetzt, um geeignete Prozessparameter zu bestimmen und deren Auswirkungen auf die transienten thermischen und mechanischen Vorg{\"a}nge, die w{\"a}hrend des Schweißvorgangs ablaufen abzubilden. Um die aus der Simulation erhaltenen Aussagen zu {\"u}berpr{\"u}fen, ist es erforderlich, das Berechnungsmodell mittels Daten aus Versuchsschweißungen zu kalibrieren. Dabei sind die verwendeten Materialmodelle sowie die der Simulation zugrunde gelegten Materialkennwerte zu validieren. Es stehen verschiedene rheologische Berechnungsmodelle zur Auswahl, die die viskosen Materialeigenschaften des Glases abbilden. Dabei werden die drei mechanischen Grundelemente, die HOOKEsche Feder, der NEWTONsche D{\"a}mpfungszylinder und das ST.-VENANT-Element miteinander kombiniert. Die M{\"o}glichkeit, thermische und mechanische Vorg{\"a}nge innerhalb des Glases w{\"a}hrend des Schweißvorgangs und nach vollst{\"a}ndiger Abk{\"u}hlung, vorhersagen zu k{\"o}nnen, gestattet es den Schweißvorgang {\"u}ber eine Optimierung der Verfahrensparameter gezielt dahingehend zu beeinflussen, die Wirtschaftlichkeit des Schweißverfahrens zu verbessern, und ein zuverl{\"a}ssiges Schweißergebnis zu erhalten. Dabei k{\"o}nnen auch nur unter hohem experimentellen Aufwand durchf{\"u}hrbare Versuche simuliert werden, um eine Vorhersage zu treffen, ob es zweckm{\"a}ßig ist, den Versuch auch in der Praxis zu fahren. Dies f{\"u}hrt zu einer Reduzierung des experimentellen Aufwandes und damit zu einer Verk{\"u}rzung des Entwicklungszeitraumes f{\"u}r das angestrebte Verfahren.}, subject = {Architektur }, language = {de} } @inproceedings{Geyer, author = {Geyer, Philipp}, title = {MODELS FOR MULTIDISCIPLINARY DESIGN OPTIMIZATION: AN EXEMPLARY OFFICE BUILDING}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2957}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29574}, pages = {10}, abstract = {The mathematical and technical foundations of optimization have been developed to a large extent. In the design of buildings, however, optimization is rarely applied because of insufficient adaptation of this method to the needs of building design. The use of design optimization requires the consideration of all relevant objectives in an interactive and multidisciplinary process. Disciplines such as structural, light, and thermal engineering, architecture, and economics impose various objectives on the design. A good solution calls for a compromise between these often contradictory objectives. This presentation outlines a method for the application of Multidisciplinary Design Optimization (MDO) as a tool for the designing of buildings. An optimization model is established considering the fact that in building design the non-numerical aspects are of major importance than in other engineering disciplines. A component-based decomposition enables the designer to manage the non-numerical aspects in an interactive design optimization process. A fa{\c{c}}ade example demonstrates a way how the different disciplines interact and how the components integrate the disciplines in one optimization model. In this grid-based fa{\c{c}}ade example, the materials switch between a discrete number of materials and construction types. For light and thermal engineering, architecture, and economics, analysis functions calculate the performance; utility functions serve as an important means for the evaluation since not every increase or decrease of a physical value improves the design. For experimental purposes, a genetic algorithm applied to the exemplary model demonstrates the use of optimization in this design case. A component-based representation first serves to manage non-numerical characteristics such as aesthetics. Furthermore, it complies with usual fabrication methods in building design and with object-oriented data handling in CAD. Therefore, components provide an important basis for an interactive MDO process in building design.}, subject = {Architektur }, language = {en} } @inproceedings{GalffyBaitschWellmannJelicetal., author = {Galffy, Mozes and Baitsch, Matthias and Wellmann Jelic, Andres and Hartmann, Dietrich}, title = {LIFETIME-ORIENTED OPTIMIZATION OF BRIDGE TIE RODS EXPOSED TO VORTEX-INDUCED ACROSS-WIND VIBRATIONS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2956}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29561}, pages = {12}, abstract = {In recent years, damages in welded connections plates of vertical tie rods of several arched steel bridges have been reported. These damages are due to fatigue caused by wind-induced vibrations. In the present study, such phenomena are examined, and the corresponding lifetime of a reference bridge in M{\"u}nster-Hiltrup, Germany, is estimated, based on the actual shape of the connection plate. Also, the results obtained are compared to the expected lifetime of a connection plate, whose geometry has been optimized separately. The structural optimization, focussing on the shape of the cut at the hanger ends, has been carried out using evolution strategies. The oscillation amplitudes have been computed by means of the Newmark-Wilson time-step method, using an appropriate load model, which has been validated by on-site experiments on the selected reference bridge. Corresponding stress-amplitudes are evaluated by multiplying the oscillation amplitudes with a stress concentration factor. This factor has been computed on the basis of a finite element model of the system "hanger-welding-connection plate", applying solid elements, according to the notch stress approach. The damage estimation takes into account the stochastics of the exciting wind process, as well as the stochastics of the material parameters (fatigue strength) given in terms of Woehler-curves. The shape optimization results in a substantial increase of the estimated hanger lifetime. The comparison of the lifetimes of the bulk plate and of the welding revealed that, in the optimized structure, the welding, being the most sensitive part in the original structure, shows much more resistance against potential damages than the bulk material.}, subject = {Architektur }, language = {en} } @inproceedings{Faustino, author = {Faustino, Nelson}, title = {FISCHER DECOMPOSITION FOR DIFFERENCE DIRAC OPERATORS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2955}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29551}, pages = {10}, abstract = {We establish the basis of a discrete function theory starting with a Fischer decomposition for difference Dirac operators. Discrete versions of homogeneous polynomials, Euler and Gamma operators are obtained. As a consequence we obtain a Fischer decomposition for the discrete Laplacian. For the sake of simplicity we consider in the first part only Dirac operators which contain only forward or backward finite differences. Of course, these Dirac operators do not factorize the classic discrete Laplacian. Therefore, we will consider a different definition of a difference Dirac operator in the quaternionic case which do factorizes the discrete Laplacian.}, subject = {Architektur }, language = {en} } @inproceedings{MalonekFalcaoSilva, author = {Malonek, Helmuth Robert and Falc{\~a}o, M. Irene and Silva, Ant{\´o}nio}, title = {MAPLE TOOLS FOR MODIFIED QUATERNIONIC ANALYSIS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2953}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29535}, pages = {7}, abstract = {At the 16th IKM Bock, Falc{\~a}o and G{\"u}rlebeck presented examples of the application of some specially developed Maple-Software in hypercomplex analysis. Other papers of those authors continued this work and showed the efficiency of such tools for concrete numerical calculations as well as for numerical experiments, supporting the detection of new relationships and even theorems in a highly technical theoretical work. The mentioned software has been developed mainly for the use on mapping problems in the Euclidean spaces of dimension 3 and 4 by means of Bergman kernel methods (BKM), which are related to monogenic functions as solutions of generalized Cauchy-Riemann equations with respect to the Euclidean metric (Riesz system). The developed procedures concerning generalized powers of totally regular variables and the corresponding homogeneous polynomials basically rely on results and conventions introduced in the paper "Power series representation for monogenic functions in Rm+1 based on a permutational product", Complex Variables, 15, No.3, 181-191 (1990) by H. Malonek. Since 1992 H. Leutwiler, S. L. Eriksson and others developed in a number of papers a modified Clifford analysis and, particularly, a modified quaternionic analysis. The modification mainly consists in considering generalized Cauchy-Riemann equations with respect to a hyperbolic metric in a half space. The aim of this contribution is to show how through a change of the basic combinatorial relations used in the modified quaternionic analysis the aforementioned Maple-software (that has been recently published on CD-Rom as integrated part of the text book "Funktionentheorie in der Ebene und im Raum" by K. G{\"u}rlebeck, K. Habetha, and W. Spr{\"o}ssig, in the series "Grundstudium Mathematik" of Birkh{\"a}user Verlag, 2006) can directly be used for numerical calculations in the modified theory.}, subject = {Architektur }, language = {en} } @inproceedings{EygelaarvanRooyen, author = {Eygelaar, Anton and van Rooyen, G.C.}, title = {ENGINEERING PROCESS MODEL SPECIFICATION AND RESOURCE LEVELING}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2952}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29529}, pages = {18}, abstract = {The use of process models in the analysis, optimization and simulation of processes has proven to be extremely beneficial in the instances where they could be applied appropriately. However, the Architecture/Engineering/Construction (AEC) industries present unique challenges that complicate the modeling of their processes. A simple Engineering process model, based on the specification of Tasks, Datasets, Persons and Tools, and certain relations between them, have been developed, and its advantages over conventional techniques have been illustrated. Graph theory is used as the mathematical foundation mapping Tasks, Datasets, Persons and Tools to vertices and the relations between them to edges forming a directed graph. The acceptance of process modeling in AEC industries not only depends on the results it can provide, but the ease at which these results can be attained. Specifying a complex AEC process model is a dynamic exercise that is characterized by many modifications over the process model's lifespan. This article looks at reducing specification complexity, reducing the probability for erroneous input and allowing consistent model modification. Furthermore, the problem of resource leveling is discussed. Engineering projects are often executed with limited resources and determining the impact of such restrictions on the sequence of Tasks is important. Resource Leveling concerns itself with these restrictions caused by limited resources. This article looks at using Task shifting strategies to find a near-optimal sequence of Tasks that guarantees consistent Dataset evolution while resolving resource restrictions.}, subject = {Architektur }, language = {en} } @inproceedings{ErlemannHartmann, author = {Erlemann, Kai and Hartmann, Dietrich}, title = {PARALLELIZATION OF A MICROSCOPIC TRAFFIC SIMULATION SYSTEM USING MPIJAVA}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2951}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29516}, pages = {8}, abstract = {Traffic simulation is a valuable tool for the design and evaluation of road networks. Over the years, the level of detail to which urban and freeway traffic can be simulated has increased steadily, shifting from a merely qualitative macroscopic perspective to a very detailed microscopic view, where the behavior of individual vehicles is emulated realistically. With the improvement of behavioral models, however, the computational complexity has also steadily increased, as more and more aspects of real-life traffic have to be considered by the simulation environment. Despite the constant increase in computing power of modern personal computers, microscopic simulation stays computationally expensive, limiting the maximum network size than can be simulated on a single-processor computer in reasonable time. Parallelization can distribute the computing load from a single computer system to a cluster of several computing nodes. To this end, the exisiting simulation framework had to be adapted to allow for a distributed approach. As the simulation is ultimately targeted to be executed in real-time, incorporating real traffic data, only a spatial partition of the simulation was considered, meaning the road network has to be partitioned into subnets of comparable complexity, to ensure a homogenous load balancing. The partition process must also ensure, that the division between subnets does only occur in regions, where no strong interaction between the separated road segments occurs (i.e. not in the direct vicinity of junctions). In this paper, we describe a new microscopic reasoning voting strategy, and discuss in how far the increasing computational costs of these more complex behaviors lend themselves to a parallelized approach. We show the parallel architecture employed, the communication between computing units using MPIJava, and the benefits and pitfalls of adapting a single computer application to be used on a multi-node computing cluster.}, subject = {Architektur }, language = {en} } @inproceedings{ErikssonKettunen, author = {Eriksson, Sirkka-Liisa and Kettunen, Jarkko}, title = {HYPERMONOGENIC POLYNOMIALS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2950}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29509}, pages = {22}, abstract = {It is well know that the power function is not monogenic. There are basically two ways to include the power function into the set of solutions: The hypermonogenic functions or holomorphic Cliffordian functions. L. Pernas has found out the dimension of the space of homogenous holomorphic Cliffordian polynomials of degree m, but his approach did not include a basis. It is known that the hypermonogenic functions are included in the space of holomorphic Cliffordian functions. As our main result we show that we can construct a basis for the right module of homogeneous holomorphic Cliffordian polynomials of degree m using hypermonogenic polynomials and their derivatives. To that end we first recall the function spaces of monogenic, hypermonogenic and holomorphic Cliffordian functions and give the results needed in the proof of our main theorem. We list some basic polynomials and their properties for the various function spaces. In particular, we consider recursive formulas, rules of differentiation and properties of linear independency for the polynomials.}, subject = {Architektur }, language = {en} } @inproceedings{EiermannErnstUllmann, author = {Eiermann, Michael and Ernst, O. and Ullmann, Elisabeth}, title = {SOLUTION STRATEGIES FOR STOCHASTIC FINITE ELEMENT DISCRETIZATIONS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2949}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29493}, pages = {11}, abstract = {We consider efficient numerical methods for the solution of partial differential equations with stochastic coefficients or right hand side. The discretization is performed by the stochastic finite element method (SFEM). Separation of spatial and stochastic variables in the random input data is achieved via a Karhunen-Lo{\`e}ve expansion or Wiener's polynomial chaos expansion. We discuss solution strategies for the Galerkin system that take advantage of the special structure of the system matrix. For stochastic coefficients linear in a set of independent random variables we employ Krylov subspace recycling techniques after having decoupled the large SFEM stiffness matrix.}, subject = {Architektur }, language = {en} } @inproceedings{Eickelkamp, author = {Eickelkamp, Jens Peter}, title = {LIQUIDIT{\"A}TSPLANUNG VON BAUPROJEKTEN}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2948}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29483}, pages = {12}, abstract = {Die Liquidit{\"a}tsplanung von Bauunternehmen XE "Liquidit{\"a}tsplanung" gilt als ein wesentliches Steuerungs-, Kontroll- sowie Informationsinstrument f{\"u}r interne und externe Adressaten und {\"u}bt eine Entscheidungsunterst{\"u}tzungsfunktion aus. Da die einzelnen Bauprojekte einen wesentlichen Anteil an den Gesamtkosten des Unternehmens ausmachen, besitzen diese auch einen erheblichen Einfluß auf die Liquidit{\"a}t und die Zahlungsf{\"a}higkeit der Bauunternehmung. Dem folgend ist es in der Baupraxis eine {\"u}bliche Verfahrensweise, die Liquidit{\"a}tsplanung zuerst projektbezogen zu erstellen und anschließend auf Unternehmensebene zu verdichten. Ziel der Ausf{\"u}hrungen ist es, die Zusammenh{\"a}nge von Arbeitskalkulation XE "Arbeitskalkulation" , Ergebnisrechnung XE "Ergebnisrechnung" und Finanzrechnung XE "Finanzrechnung" in Form eines deterministischen XE "Erkl{\"a}rungsmodells" Planungsmodells auf Projektebene darzustellen. Hierbei soll das Verst{\"a}ndnis und die Bedeutung der Verkn{\"u}pfungen zwischen dem technisch-orientierten Bauablauf und dessen Darstellung im Rechnungs- und Finanzwesen herausgestellt werden. Die Vorg{\"a}nge aus der Bauabwicklung, das heißt die Abarbeitung der Bauleistungsverzeichnispositionen und deren zeitliche Darstellung in einem Bauzeitenplan sind periodisiert in Gr{\"o}ßen der Betriebsbuchhaltung (Leistung, Kosten) zu transformieren und anschließend in der Finanzrechnung (Einzahlungen., Auszahlungen) nach Kreditoren und Debitoren aufzuschl{\"u}sseln.}, subject = {Architektur }, language = {de} } @inproceedings{EckardtKoenke, author = {Eckardt, Stefan and K{\"o}nke, Carsten}, title = {ADAPTIVE SIMULATION OF THE DAMAGE BEHAVIOR OF CONCRETE USING HETEROGENEOUS MULTISCALE MODELS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2947}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29478}, pages = {15}, abstract = {In this paper an adaptive heterogeneous multiscale model, which couples two substructures with different length scales into one numerical model is introduced for the simulation of damage in concrete. In the presented approach the initiation, propagation and coalescence of microcracks is simulated using a mesoscale model, which explicitly represents the heterogeneous material structure of concrete. The mesoscale model is restricted to the damaged parts of the structure, whereas the undamaged regions are simulated on the macroscale. As a result an adaptive enlargement of the mesoscale model during the simulation is necessary. In the first part of the paper the generation of the heterogeneous mesoscopic structure of concrete, the finite element discretization of the mesoscale model, the applied isotropic damage model and the cohesive zone model are briefly introduced. Furthermore the mesoscale simulation of a uniaxial tension test of a concrete prism is presented and own obtained numerical results are compared to experimental results. The second part is focused on the adaptive heterogeneous multiscale approach. Indicators for the model adaptation and for the coupling between the different numerical models will be introduced. The transfer from the macroscale to the mesoscale and the adaptive enlargement of the mesoscale substructure will be presented in detail. A nonlinear simulation of a realistic structure using an adaptive heterogeneous multiscale model is presented at the end of the paper to show the applicability of the proposed approach to large-scale structures.}, subject = {Architektur }, language = {en} } @inproceedings{EblingScheuermann, author = {Ebling, Julia and Scheuermann, G.}, title = {TEMPLATE MATCHING ON VECTOR FIELDS USING CLIFFORD ALGEBRA}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2946}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29464}, pages = {25}, abstract = {Due to the amount of flow simulation and measurement data, automatic detection, classification and visualization of features is necessary for an inspection. Therefore, many automated feature detection methods have been developed in recent years. However, only one feature class is visualized afterwards in most cases, and many algorithms have problems in the presence of noise or superposition effects. In contrast, image processing and computer vision have robust methods for feature extraction and computation of derivatives of scalar fields. Furthermore, interpolation and other filter can be analyzed in detail. An application of these methods to vector fields would provide a solid theoretical basis for feature extraction. The authors suggest Clifford algebra as a mathematical framework for this task. Clifford algebra provides a unified notation for scalars and vectors as well as a multiplication of all basis elements. The Clifford product of two vectors provides the complete geometric information of the relative positions of these vectors. Integration of this product results in Clifford correlation and convolution which can be used for template matching of vector fields. For frequency analysis of vector fields and the behavior of vector-valued filters, a Clifford Fourier transform has been derived for 2D and 3D. Convolution and other theorems have been proved, and fast algorithms for the computation of the Clifford Fourier transform exist. Therefore the computation of Clifford convolution can be accelerated by computing it in Clifford Fourier domain. Clifford convolution and Fourier transform can be used for a thorough analysis and subsequent visualization of flow fields.}, subject = {Architektur }, language = {en} } @inproceedings{EbertLenzen, author = {Ebert, Carsten and Lenzen, Armin}, title = {OUTPUT-ONLY ANALYSIS FOR EXPERIMENTAL DAMAGE DETECTION OF A TIED-ARCH BRIDGE}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2945}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29452}, pages = {13}, abstract = {In civil engineering it is very difficult and often expensive to excite constructions such as bridges and buildings with an impulse hammer or shaker. This problem can be avoided with the output-only method as special feature of stochastic system identification. The permanently existing ambient noise (e.g. wind, traffic, waves) is sufficient to excite the structures in their operational conditions. The output-only method is able to estimate the observable part of a state-space-model which contains the dynamic characteristics of the measured mechanical system. Because of the assumption that the ambient excitation is white there is no requirement to measure the input. Another advantage of the output-only method is the possibility to get high detailed models by a special method, called polyreference setup. To pretend the availability of a much larger set of sensors the data from varying sensor locations will be collected. Several successive data sets are recorded with sensors at different locations (moving sensors) and fixed locations (reference sensors). The covariance functions of the reference sensors are bases to normalize the moving sensors. The result of the following subspace-based system identification is a high detailed black-box-model that contains the weighting function including the well-known dynamic parameters eigenfrequencies and mode shapes of the mechanical system. Emphasis of this lecture is the presentation of an extensive damage detection experiment. A 53-year old prestressed concrete tied-arch-bridge in H{\"u}nxe (Germany) was deconstructed in 2005. Preliminary numerous vibration measurements were accomplished. The first experiment for system modification was an additional support near the bridge bearing of one main girder. During a further experiment one hanger from one tied arch was cut through as an induced damage. Some first outcomes of the described experiments will be presented.}, subject = {Architektur }, language = {en} } @inproceedings{DzwigonHempel, author = {Dzwigon, Wieslaw and Hempel, Lorenz}, title = {ZUR SYNCHRONISATION VON LINIEN IM {\"O}PNV}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2944}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29442}, pages = {12}, abstract = {Wir betrachten im {\"O}PNV ({\"O}ffentlichen Personennahverkehr) diejenige Situation, daß zwei Bus- oder Straßenbahnlinien gemeinsame Haltestellen haben. Ziel unserer Untersuchungen ist es, f{\"u}r beide Linien einen solchen Fahrplan zu finden, der f{\"u}r die Fahrg{\"a}ste m{\"o}glichst viel Bequemlichkeit bietet. Die Bedarfsstruktur - die Anzahl von Personen, die die beiden Linien benutzen - setzt dabei gewisse Beschr{\"a}nkungen f{\"u}r die Taktzeiten der beiden Linien. Die verbleibenden Entscheidungsfreiheiten sollen im Sinne der Zielstellung ausgenutzt werden. Im Vortrag wird folgenden Fragen nachgegangen: - nach welchen Kriterien kann man die "Bequemlichkeit" oder die "Synchonisationsg{\"u}te" messen? - wie kann man die einzelnen "Synchronisationsmaße" berechnen ? - wie kann man die verbleibenden Entscheidungsfreiheiten nutzen, um eine m{\"o}glichst gute Synchronisation zu erreichen ? Die Ergebnisse werden dann auf einige Beispiele angewandt und mit den bereitgestellten Methoden L{\"o}sungsvorschl{\"a}ge unterbreitet.}, subject = {Architektur }, language = {de} } @inproceedings{DudekRichter, author = {Dudek, Mariusz and Richter, Matthias}, title = {UNTERSUCHUNGEN ZUR ZUVERL{\"A}SSIGKEIT DES STRAßENBAHNNETZES IN KRAKAU}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2943}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29432}, pages = {19}, abstract = {Der Begriff der Zuverl{\"a}ssigkeit spielt eine zentrale Rolle bei der Bewertung von Verkehrsnetzen. Aus der Sicht der Nutzer des {\"o}ffentlichen Personennahverkehrs ({\"O}PNV) ist eines der wichtigsten Kriterien zur Beurteilung der Qualit{\"a}t des Liniennetzes, ob es m{\"o}glich ist, mit einer großen Sicherheit das Reiseziel in einer vorgegebenen Zeit zu erreichen. Im Vortrag soll dieser Zuverl{\"a}ssigkeitsbegriff mathematisch gefasst werden. Dabei wird zun{\"a}chst auf den {\"u}blichen Begriff der Zuverl{\"a}ssigkeit eines Netzes im Sinne paarweiser Zusammenhangswahrscheinlichkeiten eingegangen. Dieser Begriff wird erweitert durch die Betrachtung der Zuverl{\"a}ssigkeit unter Einbeziehung einer maximal zul{\"a}ssigen Reisezeit. In vergangenen Arbeiten hat sich die Ring-Radius-Struktur als bew{\"a}hrtes Modell f{\"u}r die theoretische Beschreibung von Verkehrsnetzen erwiesen. Diese {\"U}berlegungen sollen nun durch Einbeziehung realer Verkehrsnetzstrukturen erweitert werden. Als konkretes Beispiel dient das Straßenbahnnetz von Krakau. Hier soll insbesondere untersucht werden, welche Auswirkungen ein geplanter Ausbau des Netzes auf die Zuverl{\"a}ssigkeit haben wird. This paper is involved with CIVITAS-CARAVEL project: "Clean and better transport in cites". The project has received research funding from the Community's Sixth Framework Programme. The paper reflects only the author's views and the Community is not liable for any use that may be made of the information contained therein.}, subject = {Architektur }, language = {de} } @inproceedings{DoganArditiGunaydin, author = {Dogan, Sevgi Zeynep and Arditi, D. and Gunaydin, H. Murat}, title = {COMPARISON OF ANN AND CBR MODELS FOR EARLY COST PREDICTION OF STRUCTURAL SYSTEMS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2942}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29421}, abstract = {Reasonably accurate cost estimation of the structural system is quite desirable at the early stages of the design process of a construction project. However, the numerous interactions among the many cost-variables make the prediction difficult. Artificial neural networks (ANN) and case-based reasoning (CBR) are reported to overcome this difficulty. This paper presents a comparison of CBR and ANN augmented by genetic algorithms (GA) conducted by using spreadsheet simulations. GA was used to determine the optimum weights for the ANN and CBR models. The cost data of twenty-nine actual cases of residential building projects were used as an example application. Two different sets of cases were randomly selected from the data set for training and testing purposes. Prediction rates of 84\% in the GA/CBR study and 89\% in the GA/ANN study were obtained. The advantages and disadvantages of the two approaches are discussed in the light of the experiments and the findings. It appears that GA/ANN is a more suitable model for this example of cost estimation where the prediction of numerical values is required and only a limited number of cases exist. The integration of GA into CBR and ANN in a spreadsheet format is likely to improve the prediction rates.}, subject = {Architektur }, language = {en} } @inproceedings{DeaconvanRooyen, author = {Deacon, Michael-John and van Rooyen, G.C.}, title = {DISTRIBUTED COLLABORATION: ENGINEERING PRACTICE REQUIREMENTS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2941}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29410}, pages = {8}, abstract = {Designing a structure follows a pattern of creating a structural design concept, executing a finite element analysis and developing a design model. A project was undertaken to create computer support for executing these tasks within a collaborative environment. This study focuses on developing a software architecture that integrates the various structural design aspects into a seamless functional collaboratory that satisfies engineering practice requirements. The collaboratory is to support both homogeneous collaboration i.e. between users operating on the same model and heterogeneous collaboration i.e. between users operating on different model types. Collaboration can take place synchronously or asynchronously, and the information exchange is done either at the granularity of objects or at the granularity of models. The objective is to determine from practicing engineers which configurations they regard as best and what features are essential for working in a collaborative environment. Based on the suggestions of these engineers a specification of a collaboration configuration that satisfies engineering practice requirements will be developed.}, subject = {Architektur }, language = {en} } @inproceedings{CruzFalcaoMalonek, author = {Cruz, J. F. and Falc{\~a}o, M. Irene and Malonek, Helmuth Robert}, title = {3D-MAPPINGS AND THEIR APPROXIMATION BY SERIES OF POWERS OF A SMALL PARAMETER}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2940}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29406}, pages = {14}, abstract = {In classical complex function theory the geometric mapping property of conformality is closely linked with complex differentiability. In contrast to the planar case, in higher dimensions the set of conformal mappings is only the set of M{\"o}bius transformations. Unfortunately, the theory of generalized holomorphic functions (by historical reasons they are called monogenic functions) developed on the basis of Clifford algebras does not cover the set of M{\"o}bius transformations in higher dimensions, since M{\"o}bius transformations are not monogenic. But on the other side, monogenic functions are hypercomplex differentiable functions and the question arises if from this point of view they can still play a special role for other types of 3D-mappings, for instance, for quasi-conformal ones. On the occasion of the 16th IKM 3D-mapping methods based on the application of Bergman's reproducing kernel approach (BKM) have been discussed. Almost all authors working before that with BKM in the Clifford setting were only concerned with the general algebraic and functional analytic background which allows the explicit determination of the kernel in special situations. The main goal of the abovementioned contribution was the numerical experiment by using a Maple software specially developed for that purpose. Since BKM is only one of a great variety of concrete numerical methods developed for mapping problems, our goal is to present a complete different from BKM approach to 3D-mappings. In fact, it is an extension of ideas of L. V. Kantorovich to the 3-dimensional case by using reduced quaternions and some suitable series of powers of a small parameter. Whereas until now in the Clifford case of BKM the recovering of the mapping function itself and its relation to the monogenic kernel function is still an open problem, this approach avoids such difficulties and leads to an approximation by monogenic polynomials depending on that small parameter.}, subject = {Architektur }, language = {en} } @inproceedings{FalcaoCruzMalonek, author = {Falc{\~a}o, M. Irene and Cruz, J. F. and Malonek, Helmuth Robert}, title = {REMARKS ON THE GENERATION OF MONOGENIC FUNCTIONS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2939}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29390}, pages = {18}, abstract = { In this paper we consider three different methods for generating monogenic functions. The first one is related to Fueter's well known approach to the generation of monogenic quaternion-valued functions by means of holomorphic functions, the second one is based on the solution of hypercomplex differential equations and finally the third one is a direct series approach, based on the use of special homogeneous polynomials. We illustrate the theory by generating three different exponential functions and discuss some of their properties. Formula que se usa em preprints e artigos da nossa UI\&D (acho demasiado completo): Partially supported by the R\\&D unit \emph{Matem\'atica a Aplica\c\~es} (UIMA) of the University of Aveiro, through the Portuguese Foundation for Science and Technology (FCT), co-financed by the European Community fund FEDER.}, subject = {Architektur }, language = {en} } @inproceedings{ConstalesKrausshar, author = {Constales, Denis and Kraußhar, Rolf S{\"o}ren}, title = {ON THE NAVIER-STOKES EQUATION WITH FREE CONVECTION IN STRIP DOMAINS AND 3D TRIANGULAR CHANNELS}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2938}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29387}, pages = {12}, abstract = {The Navier-Stokes equations and related ones can be treated very elegantly with the quaternionic operator calculus developed in a series of works by K. Guerlebeck, W. Sproeossig and others. This study will be extended in this paper. In order to apply the quaternionic operator calculus to solve these types of boundary value problems fully explicitly, one basically needs to evaluate two types of integral operators: the Teodorescu operator and the quaternionic Bergman projector. While the integral kernel of the Teodorescu transform is universal for all domains, the kernel function of the Bergman projector, called the Bergman kernel, depends on the geometry of the domain. With special variants of quaternionic holomorphic multiperiodic functions we obtain explicit formulas for three dimensional parallel plate channels, rectangular block domains and regular triangular channels. The explicit knowledge of the integral kernels makes it then possible to evaluate the operator equations in order to determine the solutions of the boundary value problem explicitly.}, subject = {Architektur }, language = {en} } @inproceedings{ChangChang, author = {Chang, Wei-Tsang and Chang, Teng-Wen}, title = {TIME-BASED FORM TRANSFORMATION WITH FOLDING SPACE}, editor = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten}, organization = {Bauhaus-Universit{\"a}t Weimar}, doi = {10.25643/bauhaus-universitaet.2937}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29371}, pages = {10}, abstract = {Design activity could be treated as state transition computationally. In stepwise processing, in-between form-states are not easily observed. However, in this research time-based concept is introduced and applied in order to bridge the gap. In architecture, folding is one method of form manipulation and architects also want to search for alternatives by this operation. Besides, folding operation has to be defined and parameterized before time factor is involved as a variable of folding. As a result, time-based transformation provides sequential form states and redirects design activity.}, subject = {Architektur }, language = {en} }