@article{HarirchianKumariJadhavetal., author = {Harirchian, Ehsan and Kumari, Vandana and Jadhav, Kirti and Rasulzade, Shahla and Lahmer, Tom and Raj Das, Rohan}, title = {A Synthesized Study Based on Machine Learning Approaches for Rapid Classifying Earthquake Damage Grades to RC Buildings}, series = {Applied Sciences}, volume = {2021}, journal = {Applied Sciences}, number = {Volume 11, issue 16, article 7540}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11167540}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210818-44853}, pages = {1 -- 33}, abstract = {A vast number of existing buildings were constructed before the development and enforcement of seismic design codes, which run into the risk of being severely damaged under the action of seismic excitations. This poses not only a threat to the life of people but also affects the socio-economic stability in the affected area. Therefore, it is necessary to assess such buildings' present vulnerability to make an educated decision regarding risk mitigation by seismic strengthening techniques such as retrofitting. However, it is economically and timely manner not feasible to inspect, repair, and augment every old building on an urban scale. As a result, a reliable rapid screening methods, namely Rapid Visual Screening (RVS), have garnered increasing interest among researchers and decision-makers alike. In this study, the effectiveness of five different Machine Learning (ML) techniques in vulnerability prediction applications have been investigated. The damage data of four different earthquakes from Ecuador, Haiti, Nepal, and South Korea, have been utilized to train and test the developed models. Eight performance modifiers have been implemented as variables with a supervised ML. The investigations on this paper illustrate that the assessed vulnerability classes by ML techniques were very close to the actual damage levels observed in the buildings.}, subject = {Maschinelles Lernen}, language = {en} } @article{MeiabadiMoradiKaramimoghadametal., author = {Meiabadi, Mohammad Saleh and Moradi, Mahmoud and Karamimoghadam, Mojtaba and Ardabili, Sina and Bodaghi, Mahdi and Shokri, Manouchehr and Mosavi, Amir Hosein}, title = {Modeling the Producibility of 3D Printing in Polylactic Acid Using Artificial Neural Networks and Fused Filament Fabrication}, series = {polymers}, volume = {2021}, journal = {polymers}, number = {Volume 13, issue 19, article 3219}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/polym13193219}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220110-45518}, pages = {1 -- 21}, abstract = {Polylactic acid (PLA) is a highly applicable material that is used in 3D printers due to some significant features such as its deformation property and affordable cost. For improvement of the end-use quality, it is of significant importance to enhance the quality of fused filament fabrication (FFF)-printed objects in PLA. The purpose of this investigation was to boost toughness and to reduce the production cost of the FFF-printed tensile test samples with the desired part thickness. To remove the need for numerous and idle printing samples, the response surface method (RSM) was used. Statistical analysis was performed to deal with this concern by considering extruder temperature (ET), infill percentage (IP), and layer thickness (LT) as controlled factors. The artificial intelligence method of artificial neural network (ANN) and ANN-genetic algorithm (ANN-GA) were further developed to estimate the toughness, part thickness, and production-cost-dependent variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid machine learning (ML) technique could enhance the accuracy of modeling by about 7.5, 11.5, and 4.5\% for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. On the other hand, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which enables the usability of printed PLA objects.}, subject = {3D-Druck}, language = {en} } @article{LashkarAraKalantariSheikhKhozanietal., author = {Lashkar-Ara, Babak and Kalantari, Niloofar and Sheikh Khozani, Zohreh and Mosavi, Amir}, title = {Assessing Machine Learning versus a Mathematical Model to Estimate the Transverse Shear Stress Distribution in a Rectangular Channel}, series = {Mathematics}, volume = {2021}, journal = {Mathematics}, number = {Volume 9, Issue 6, Article 596}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/math9060596}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210504-44197}, pages = {15}, abstract = {One of the most important subjects of hydraulic engineering is the reliable estimation of the transverse distribution in the rectangular channel of bed and wall shear stresses. This study makes use of the Tsallis entropy, genetic programming (GP) and adaptive neuro-fuzzy inference system (ANFIS) methods to assess the shear stress distribution (SSD) in the rectangular channel. To evaluate the results of the Tsallis entropy, GP and ANFIS models, laboratory observations were used in which shear stress was measured using an optimized Preston tube. This is then used to measure the SSD in various aspect ratios in the rectangular channel. To investigate the shear stress percentage, 10 data series with a total of 112 different data for were used. The results of the sensitivity analysis show that the most influential parameter for the SSD in smooth rectangular channel is the dimensionless parameter B/H, Where the transverse coordinate is B, and the flow depth is H. With the parameters (b/B), (B/H) for the bed and (z/H), (B/H) for the wall as inputs, the modeling of the GP was better than the other one. Based on the analysis, it can be concluded that the use of GP and ANFIS algorithms is more effective in estimating shear stress in smooth rectangular channels than the Tsallis entropy-based equations.}, subject = {Maschinelles Lernen}, language = {en} }