@article{MehlingSchnabelLondong, author = {Mehling, Simon and Schnabel, Tobias and Londong, J{\"o}rg}, title = {Photocatalytic ozonation in an immersion rotary body reactor for the removal of micro-pollutants from the effluent of wastewater treatment plants}, series = {Water Science \& Technology}, volume = {2022}, journal = {Water Science \& Technology}, number = {volume 85, issue 1}, publisher = {IWA Publishing}, address = {London}, doi = {10.2166/wst.2021.617}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220209-45865}, pages = {535 -- 548}, abstract = {Carrier-bound titanium dioxide catalysts were used in a photocatalytic ozonation reactor for the degradation of micro-pollutants in real wastewater. A photocatalytic immersion rotary body reactor with a 36-cm disk diameter was used, and was irradiated using UV-A light-emitting diodes. The rotating disks were covered with catalysts based on stainless steel grids coated with titanium dioxide. The dosing of ozone was carried out through the liquid phase via an external enrichment and a supply system transverse to the flow direction. The influence of irradiation power and ozone dose on the degradation rate for photocatalytic ozonation was investigated. In addition, the performance of the individual processes photocatalysis and ozonation were studied. The degradation kinetics of the parent compounds were determined using liquid chromatography tandem mass spectrometry. First-order kinetics were determined for photocatalysis and photocatalytic ozonation. A maximum reaction rate of the reactor was determined, which could be achieved by both photocatalysis and photocatalytic ozonation. At a dosage of 0.4 mg /mg DOC, the maximum reaction rate could be achieved using 75\% of the irradiation power used for sole photocatalysis, allowing increases in the energetic efficiency of photocatalytic wastewater treatment processes. The process of photocatalytic ozonation is suitable to remove a wide spectrum of micro-pollutants from wastewater.}, subject = {Abwasserreinigung}, language = {en} } @article{HarirchianKumariJadhavetal., author = {Harirchian, Ehsan and Kumari, Vandana and Jadhav, Kirti and Rasulzade, Shahla and Lahmer, Tom and Raj Das, Rohan}, title = {A Synthesized Study Based on Machine Learning Approaches for Rapid Classifying Earthquake Damage Grades to RC Buildings}, series = {Applied Sciences}, volume = {2021}, journal = {Applied Sciences}, number = {Volume 11, issue 16, article 7540}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11167540}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210818-44853}, pages = {1 -- 33}, abstract = {A vast number of existing buildings were constructed before the development and enforcement of seismic design codes, which run into the risk of being severely damaged under the action of seismic excitations. This poses not only a threat to the life of people but also affects the socio-economic stability in the affected area. Therefore, it is necessary to assess such buildings' present vulnerability to make an educated decision regarding risk mitigation by seismic strengthening techniques such as retrofitting. However, it is economically and timely manner not feasible to inspect, repair, and augment every old building on an urban scale. As a result, a reliable rapid screening methods, namely Rapid Visual Screening (RVS), have garnered increasing interest among researchers and decision-makers alike. In this study, the effectiveness of five different Machine Learning (ML) techniques in vulnerability prediction applications have been investigated. The damage data of four different earthquakes from Ecuador, Haiti, Nepal, and South Korea, have been utilized to train and test the developed models. Eight performance modifiers have been implemented as variables with a supervised ML. The investigations on this paper illustrate that the assessed vulnerability classes by ML techniques were very close to the actual damage levels observed in the buildings.}, subject = {Maschinelles Lernen}, language = {en} } @article{Legatiuk, author = {Legatiuk, Dmitrii}, title = {Mathematical Modelling by Help of Category Theory: Models and Relations between Them}, series = {mathematics}, volume = {2021}, journal = {mathematics}, number = {volume 9, issue 16, article 1946}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/math9161946}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210817-44844}, pages = {17}, abstract = {The growing complexity of modern practical problems puts high demand on mathematical modelling. Given that various models can be used for modelling one physical phenomenon, the role of model comparison and model choice is becoming particularly important. Methods for model comparison and model choice typically used in practical applications nowadays are computationbased, and thus time consuming and computationally costly. Therefore, it is necessary to develop other approaches to working abstractly, i.e., without computations, with mathematical models. An abstract description of mathematical models can be achieved by the help of abstract mathematics, implying formalisation of models and relations between them. In this paper, a category theory-based approach to mathematical modelling is proposed. In this way, mathematical models are formalised in the language of categories, relations between the models are formally defined and several practically relevant properties are introduced on the level of categories. Finally, an illustrative example is presented, underlying how the category-theory based approach can be used in practice. Further, all constructions presented in this paper are also discussed from a modelling point of view by making explicit the link to concrete modelling scenarios.}, subject = {Kategorientheorie}, language = {en} } @article{RenZhuangOterkusetal., author = {Ren, Huilong and Zhuang, Xiaoying and Oterkus, Erkan and Zhu, Hehua and Rabczuk, Timon}, title = {Nonlocal strong forms of thin plate, gradient elasticity, magneto-electro-elasticity and phase-field fracture by nonlocal operator method}, series = {Engineering with Computers}, volume = {2021}, journal = {Engineering with Computers}, doi = {10.1007/s00366-021-01502-8}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20211207-45388}, pages = {1 -- 22}, abstract = {The derivation of nonlocal strong forms for many physical problems remains cumbersome in traditional methods. In this paper, we apply the variational principle/weighted residual method based on nonlocal operator method for the derivation of nonlocal forms for elasticity, thin plate, gradient elasticity, electro-magneto-elasticity and phase-field fracture method. The nonlocal governing equations are expressed as an integral form on support and dual-support. The first example shows that the nonlocal elasticity has the same form as dual-horizon non-ordinary state-based peridynamics. The derivation is simple and general and it can convert efficiently many local physical models into their corresponding nonlocal forms. In addition, a criterion based on the instability of the nonlocal gradient is proposed for the fracture modelling in linear elasticity. Several numerical examples are presented to validate nonlocal elasticity and the nonlocal thin plate.}, subject = {Bruchmechanik}, language = {en} } @article{AlsaadVoelker, author = {Alsaad, Hayder and V{\"o}lker, Conrad}, title = {Qualitative evaluation of the flow supplied by personalized ventilation using schlieren imaging and thermography}, series = {Building and Environment}, volume = {2020}, journal = {Building and Environment}, number = {Volume 167, article 106450}, publisher = {Elsevier}, address = {New York}, doi = {10.25643/bauhaus-universitaet.4511}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20211008-45117}, pages = {11}, abstract = {Personalized ventilation (PV) is a mean of delivering conditioned outdoor air into the breathing zone of the occupants. This study aims to qualitatively investigate the personalized flows using two methods of visualization: (1) schlieren imaging using a large schlieren mirror and (2) thermography using an infrared camera. While the schlieren imaging was used to render the velocity and mass transport of the supplied flow, thermography was implemented to visualize the air temperature distribution induced by the PV. Both studies were conducted using a thermal manikin to simulate an occupant facing a PV outlet. As a reference, the flow supplied by an axial fan and a cased axial fan was visualized with the schlieren system as well and compared to the flow supplied by PV. Schlieren visualization results indicate that the steady, low-turbulence flow supplied by PV was able to penetrate the thermal convective boundary layer encasing the manikin's body, providing clean air for inhalation. Contrarily, the axial fan diffused the supplied air over a large target area with high turbulence intensity; it only disturbed the convective boundary layer rather than destroying it. The cased fan supplied a flow with a reduced target area which allowed supplying more air into the breathing zone compared to the fan. The results of thermography visualization showed that the supplied cool air from PV penetrated the corona-shaped thermal boundary layer. Furthermore, the supplied air cooled the surface temperature of the face, which indicates the large impact of PV on local thermal sensation and comfort.}, subject = {Bildverarbeitung}, language = {en} } @article{AlkamLahmer, author = {Alkam, Feras and Lahmer, Tom}, title = {A robust method of the status monitoring of catenary poles installed along high-speed electrified train tracks}, series = {Results in Engineering}, volume = {2021}, journal = {Results in Engineering}, number = {volume 12, article 100289}, publisher = {Elsevier}, address = {Amsterdam}, doi = {10.1016/j.rineng.2021.100289}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20211011-45212}, pages = {1 -- 8}, abstract = {Electric trains are considered one of the most eco-friendly and safest means of transportation. Catenary poles are used worldwide to support overhead power lines for electric trains. The performance of the catenary poles has an extensive influence on the integrity of the train systems and, consequently, the connected human services. It became a must nowadays to develop SHM systems that provide the instantaneous status of catenary poles in- service, making the decision-making processes to keep or repair the damaged poles more feasible. This study develops a data-driven, model-free approach for status monitoring of cantilever structures, focusing on pre-stressed, spun-cast ultrahigh-strength concrete catenary poles installed along high-speed train tracks. The pro-posed approach evaluates multiple damage features in an unfied damage index, which leads to straightforward interpretation and comparison of the output. Besides, it distinguishes between multiple damage scenarios of the poles, either the ones caused by material degradation of the concrete or by the cracks that can be propagated during the life span of the given structure. Moreover, using a logistic function to classify the integrity of structure avoids the expensive learning step in the existing damage detection approaches, namely, using the modern machine and deep learning methods. The findings of this study look very promising when applied to other types of cantilever structures, such as the poles that support the power transmission lines, antenna masts, chimneys, and wind turbines.}, subject = {Fahrleitung}, language = {en} } @article{Schwerzmann, author = {Schwerzmann, Katia}, title = {Abolish! Against the Use of Risk Assessment Algorithms at Sentencing in the US Criminal Justice System}, series = {Philosophy \& Technology}, volume = {2021}, journal = {Philosophy \& Technology}, doi = {10.1007/s13347-021-00491-2}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20211207-45417}, pages = {1 -- 22}, abstract = {In this article, I show why it is necessary to abolish the use of predictive algorithms in the US criminal justice system at sentencing. After presenting the functioning of these algorithms in their context of emergence, I offer three arguments to demonstrate why their abolition is imperative. First, I show that sentencing based on predictive algorithms induces a process of rewriting the temporality of the judged individual, flattening their life into a present inescapably doomed by its past. Second, I demonstrate that recursive processes, comprising predictive algorithms and the decisions based on their predictions, systematically suppress outliers and progressively transform reality to match predictions. In my third and final argument, I show that decisions made on the basis of predictive algorithms actively perform a biopolitical understanding of justice as management and modulation of risks. In such a framework, justice becomes a means to maintain a perverse social homeostasis that systematically exposes disenfranchised Black and Brown populations to risk.}, subject = {Biopolitik}, language = {en} } @article{MuellerLudwigTangeHasholt, author = {M{\"u}ller, Matthias and Ludwig, Horst-Michael and Tange Hasholt, Marianne}, title = {Salt frost attack on concrete: the combined effect of cryogenic suction and chloride binding on ice formation}, series = {Materials and Structures}, volume = {2021}, journal = {Materials and Structures}, number = {issue 54, article 189}, doi = {10.1617/s11527-021-01779-7}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20211207-45392}, pages = {1 -- 16}, abstract = {Scaling of concrete due to salt frost attack is an important durability issue in moderate and cold climates. The actual damage mechanism is still not completely understood. Two recent damage theories—the glue spall theory and the cryogenic suction theory—offer plausible, but conflicting explanations for the salt frost scaling mechanism. The present study deals with the cryogenic suction theory, which assumes that freezing concrete can take up unfrozen brine from a partly frozen deicing solution during salt frost attack. According to the model hypothesis, the resulting saturation of the concrete surface layer intensifies the ice formation in this layer and causes salt frost scaling. In this study an experimental technique was developed that makes it possible to quantify to which extent brine uptake can increase ice formation in hardened cement paste (used as a model material for concrete). The experiments were carried out with low temperature differential scanning calorimetry, where specimens were subjected to freeze-thaw cycles while being in contact with NaCl brine. Results showed that the ice content in the specimens increased with subsequent freeze-thaw cycles due to the brine uptake at temperatures below 0 °C. The ability of the hardened cement paste to bind chlorides from the absorbed brine at the same time affected the freezing/melting behavior of the pore solution and the magnitude of the ice content.}, subject = {Beton}, language = {en} } @article{SchmitzKraft, author = {Schmitz, Tonia and Kraft, Eckhard}, title = {Pilot scale photobioreactor system for land-based macroalgae cultivation}, series = {Journal of Applied Phycology}, volume = {2021}, journal = {Journal of Applied Phycology}, doi = {10.1007/s10811-021-02617-7}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20211207-45401}, pages = {1 -- 10}, abstract = {Marine macroalgae such as Ulva intestinalis have promising properties as feedstock for cosmetics and pharmaceuticals. However, since the quantity and quality of naturally grown algae vary widely, their exploitability is reduced - especially for producers in high-priced markets. Moreover, the expansion of marine or shore-based cultivation systems is unlikely in Europe, since promising sites either lie in fishing zones, recreational areas, or natural reserves. The aim was therefore to develop a closed photobioreactor system enabling full control of abiotic environmental parameters and an effective reconditioning of the cultivation medium in order to produce marine macroalgae at sites distant from the shore. To assess the feasibility and functionality of the chosen technological concept, a prototypal plant has been implemented in central Germany - a site distant from the sea. Using a newly developed, submersible LED light source, cultivation experiments with Ulva intestinalis led to growth rates of 7.72 ± 0.04 \% day-1 in a cultivation cycle of 28 days. Based on the space demand of the production system, this results in fresh mass productivity of 3.0 kg m-2, respectively, of 1.1 kg m-2 per year. Also considering the ratio of biomass to energy input amounting to 2.76 g kWh-1, significant future improvements of the developed photobioreactor system should include the optimization of growth parameters, and the reduction of the system's overall energy demand.}, subject = {Makroalgen}, language = {en} } @article{LondongBarthSoebke, author = {Londong, J{\"o}rg and Barth, Marcus and S{\"o}bke, Heinrich}, title = {Modeling and Simulation of Source Separation in Sanitation Systems for Reducing Emissions of Antimicrobial Resistances}, series = {Water}, volume = {2021}, journal = {Water}, number = {Volume 13, issue 23, article 3342}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/w13233342}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20211202-45338}, pages = {1 -- 19}, abstract = {Antimicrobial resistance (AMR) is identified by the World Health Organization (WHO) as one of the top ten threats to public health worldwide. In addition to public health, AMR also poses a major threat to food security and economic development. Current sanitation systems contribute to the emergence and spread of AMR and lack effective AMR mitigation measures. This study assesses source separation of blackwater as a mitigation measure against AMR. A source-separation-modified combined sanitation system with separate collection of blackwater and graywater is conceptually described. Measures taken at the source, such as the separate collection and discharge of material flows, were not considered so far on a load balance basis, i.e., they have not yet been evaluated for their effectiveness. The sanitation system described is compared with a combined system and a separate system regarding AMR emissions by means of simulation. AMR is represented in the simulation model by one proxy parameter each for antibiotics (sulfamethoxa-zole), antibiotic-resistant bacteria (extended-spectrum beta-lactamase E. Coli), and antibiotic re-sistance genes (blaTEM). The simulation results suggest that the source-separation-based sanitation system reduces emissions of antibiotic-resistant bacteria and antibiotic resistance genes into the aquatic environment by more than six logarithm steps compared to combined systems. Sulfa-methoxazole emissions can be reduced by 75.5\% by keeping blackwater separate from graywater and treating it sufficiently. In summary, sanitation systems incorporating source separation are, to date, among the most effective means of preventing the emission of AMR into the aquatic envi-ronment.}, subject = {Abwasser}, language = {en} } @article{KrausKlausWittor, author = {Kraus, Matthias and Klaus, Martin and Wittor, Bj{\"o}rn}, title = {Experimental Analyses on the Resistance of Tapped Blind Holes}, series = {ce/papers}, volume = {2021}, journal = {ce/papers}, number = {Volume 4, issue 2-4}, publisher = {Ernst \& Sohn, a Wiley brand}, address = {Berlin}, doi = {10.1002/cepa.1273}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220112-45553}, pages = {141 -- 147}, abstract = {Bolted connections are commonly used in steel construction. The load-bearing behavior of bolt fittings has extensively been studied in various research activities and the bearing capacity of bolted connections can be assessed well by standard regulations for practical applications. With regard to tensile loading, the nut does not have strong influence on resistances, since the failure occurs in the bolts due to higher material strengths of the nuts. In some applications, so-called "blind holes" are used to connect plated components. In a manner of speaking, the nut is replaced by the "outer" plate with a prefabricated hole and thread, in which the bolt can be screwed and tightened. In such connections, the limit load capacity cannot solely be assessed by the bolt resistance, since the threaded hole in the base material has strong influence on the structural behavior. In this context, the available screw-in depth of the blind hole is of fundamental importance. The German National Annex of EN 1993-1-8 provides information on a necessary depth in order to transfer the full tensile capacity of the bolt. However, some connections do not allow to fabricate such depths. In these cases, the capacity of the connection is unclear and not specified. In this paper, first experiments on corresponding connections with different screw-in depths are presented and compared to limit load capacities according to the standard.}, subject = {Gewinde}, language = {en} } @article{AlsaadHartmannVoelker, author = {Alsaad, Hayder and Hartmann, Maria and Voelker, Conrad}, title = {The effect of a living wall system designated for greywater treatment on the hygrothermal performance of the facade}, series = {Energy and Buildings}, volume = {2022}, journal = {Energy and Buildings}, number = {volume 255, article 111711}, doi = {10.1016/j.enbuild.2021.111711}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20240116-65299}, pages = {17}, abstract = {Besides their multiple known benefits regarding urban microclimate, living walls can be used as decentralized stand-alone systems to treat greywater locally at the buildings. While this offers numerous environmental advantages, it can have a considerable impact on the hygrothermal performance of the facade as such systems involve bringing large quantities of water onto the facade. As it is difficult to represent complex entities such as plants in the typical simulation tools used for heat and moisture transport, this study suggests a new approach to tackle this challenge by coupling two tools: ENVI-Met and Delphin. ENVI-Met was used to simulate the impact of the plants to determine the local environmental parameters at the living wall. Delphin, on the other hand, was used to conduct the hygrothermal simulations using the local parameters calculated by ENVI-Met. Four wall constructions were investigated in this study: an uninsulated brick wall, a precast concrete plate, a sandy limestone wall, and a double-shell wall. The results showed that the living wall improved the U-value, the exterior surface temperature, and the heat flux through the wall. Moreover, the living wall did not increase the risk of moisture in the wall during winter and eliminated the risk of condensation.}, subject = {Feuchteleitung}, language = {en} } @article{VakkariVoelskePotthastetal., author = {Vakkari, Pertti and V{\"o}lske, Michael and Potthast, Martin and Hagen, Matthias and Stein, Benno}, title = {Predicting essay quality from search and writing behavior}, series = {Journal of Association for Information Science and Technology}, volume = {2021}, journal = {Journal of Association for Information Science and Technology}, number = {volume 72, issue 7}, publisher = {Wiley}, address = {Hoboken, NJ}, doi = {10.1002/asi.24451}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210804-44692}, pages = {839 -- 852}, abstract = {Few studies have investigated how search behavior affects complex writing tasks. We analyze a dataset of 150 long essays whose authors searched the ClueWeb09 corpus for source material, while all querying, clicking, and writing activity was meticulously recorded. We model the effect of search and writing behavior on essay quality using path analysis. Since the boil-down and build-up writing strategies identified in previous research have been found to affect search behavior, we model each writing strategy separately. Our analysis shows that the search process contributes significantly to essay quality through both direct and mediated effects, while the author's writing strategy moderates this relationship. Our models explain 25-35\% of the variation in essay quality through rather simple search and writing process characteristics alone, a fact that has implications on how search engines could personalize result pages for writing tasks. Authors' writing strategies and associated searching patterns differ, producing differences in essay quality. In a nutshell: essay quality improves if search and writing strategies harmonize—build-up writers benefit from focused, in-depth querying, while boil-down writers fare better with a broader and shallower querying strategy.}, subject = {Information Retrieval}, language = {en} } @article{LegatiukWeiszPatrault, author = {Legatiuk, Dmitrii and Weisz-Patrault, Daniel}, title = {Coupling of Complex Function Theory and Finite Element Method for Crack Propagation Through Energetic Formulation: Conformal Mapping Approach and Reduction to a Riemann-Hilbert Problem}, series = {Computational Methods and Function Theory}, volume = {2021}, journal = {Computational Methods and Function Theory}, publisher = {Springer}, address = {Heidelberg}, doi = {10.1007/s40315-021-00403-7}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210805-44763}, pages = {1 -- 23}, abstract = {In this paper we present a theoretical background for a coupled analytical-numerical approach to model a crack propagation process in two-dimensional bounded domains. The goal of the coupled analytical-numerical approach is to obtain the correct solution behaviour near the crack tip by help of the analytical solution constructed by using tools of complex function theory and couple it continuously with the finite element solution in the region far from the singularity. In this way, crack propagation could be modelled without using remeshing. Possible directions of crack growth can be calculated through the minimization of the total energy composed of the potential energy and the dissipated energy based on the energy release rate. Within this setting, an analytical solution of a mixed boundary value problem based on complex analysis and conformal mapping techniques is presented in a circular region containing an arbitrary crack path. More precisely, the linear elastic problem is transformed into a Riemann-Hilbert problem in the unit disk for holomorphic functions. Utilising advantages of the analytical solution in the region near the crack tip, the total energy could be evaluated within short computation times for various crack kink angles and lengths leading to a potentially efficient way of computing the minimization procedure. To this end, the paper presents a general strategy of the new coupled approach for crack propagation modelling. Additionally, we also discuss obstacles in the way of practical realisation of this strategy.}, subject = {Angewandte Mathematik}, language = {en} } @article{NooriMortazaviKeshtkarietal., author = {Noori, Hamidreza and Mortazavi, Bohayra and Keshtkari, Leila and Zhuang, Xiaoying and Rabczuk, Timon}, title = {Nanopore creation in MoS2 and graphene monolayers by nanoparticles impact: a reactive molecular dynamics study}, series = {Applied Physics A}, volume = {2021}, journal = {Applied Physics A}, number = {volume 127, article 541}, publisher = {Springer}, address = {Heidelberg}, doi = {10.1007/s00339-021-04693-5}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210804-44756}, pages = {1 -- 13}, abstract = {In this work, extensive reactive molecular dynamics simulations are conducted to analyze the nanopore creation by nano-particles impact over single-layer molybdenum disulfide (MoS2) with 1T and 2H phases. We also compare the results with graphene monolayer. In our simulations, nanosheets are exposed to a spherical rigid carbon projectile with high initial velocities ranging from 2 to 23 km/s. Results for three different structures are compared to examine the most critical factors in the perforation and resistance force during the impact. To analyze the perforation and impact resistance, kinetic energy and displacement time history of the projectile as well as perforation resistance force of the projectile are investigated. Interestingly, although the elasticity module and tensile strength of the graphene are by almost five times higher than those of MoS2, the results demonstrate that 1T and 2H-MoS2 phases are more resistive to the impact loading and perforation than graphene. For the MoS2nanosheets, we realize that the 2H phase is more resistant to impact loading than the 1T counterpart. Our reactive molecular dynamics results highlight that in addition to the strength and toughness, atomic structure is another crucial factor that can contribute substantially to impact resistance of 2D materials. The obtained results can be useful to guide the experimental setups for the nanopore creation in MoS2or other 2D lattices.}, subject = {Nanomechanik}, language = {en} } @article{SeichterNesslerKnopf, author = {Seichter, Cosima Zita and Neßler, Miriam and Knopf, Paul}, title = {Der Refugee District in Belgrad. Ein Raum der Nicht-Bewegung zwischen neoliberaler Stadtentwicklung, serbischem Migrationsmanagement und EU-Grenzregime}, series = {sub\urban. Zeitschrift f{\"u}r Kritische Stadtforschung}, volume = {2021}, journal = {sub\urban. Zeitschrift f{\"u}r Kritische Stadtforschung}, number = {Band 9, Heft 1/2}, publisher = {sub\urban e.V.}, address = {Berlin}, doi = {10.36900/suburban.v9i1/2.622}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20210805-44776}, pages = {225 -- 234}, abstract = {Durch internationale Fluchtbewegungen {\"u}ber die sogenannte Balkanroute bildete sich in Serbiens Hauptstadt Belgrad in den letzten Jahren ein sogenannter Refugee District heraus. Im Kontext von Migration und Flucht werden dabei zahlreiche Spannungsfelder auf unterschiedlichen r{\"a}umlichen und politischen Ebenen sichtbar. F{\"u}r Fl{\"u}chtende kreieren diese eine Situation, die von Stillstand, Ausweglosigkeit, Kontrolle, Gefahr und Verdr{\"a}ngung gepr{\"a}gt ist. Allerdings f{\"u}hren die Vielschichtigkeit und die Diversit{\"a}t unterschiedlicher Akteur*innen, die bez{\"u}glich der Situation von Fl{\"u}chtenden auf der Balkanroute wirkm{\"a}chtig sind, auch zu Nischen, Widerst{\"a}ndigkeiten und der M{\"o}glichkeit (neuer) Allianzen. Auf diese Weise entsteht eine kollektive Praktik der Nicht-Bewegung im Widerstand gegen die Unterdr{\"u}ckung und f{\"u}r globale Bewegungsfreiheit.}, subject = {Belgrad}, language = {de} } @article{KrausCrişanWittor, author = {Kraus, Matthias and Cri{\c{s}}an, Nicolae-Andrei and Wittor, Bj{\"o}rn}, title = {Stability Study of Cantilever-Beams - Numerical Analysis and Analytical Calculation (LTB)}, series = {ce/papers}, volume = {2021}, journal = {ce/papers}, number = {Volume 4, issue 2-4}, publisher = {Ernst \& Sohn, a Wiley brand}, address = {Berlin}, doi = {10.1002/cepa.1539}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220112-45637}, pages = {2199 -- 2206}, abstract = {According to Eurocode, the computation of bending strength for steel cantilever beams is a straightforward process. The approach is based on an Ayrton-Perry formula adaptation of buckling curves for steel members in compression, which involves the computation of an elastic critical buckling load for considering the instability. NCCI documents offer a simplified formula to determine the critical bending moment for cantilevers beams with symmetric cross-section. Besides the NCCI recommendations, other approaches, e.g. research literature or Finite-Element-Analysis, may be employed to determine critical buckling loads. However, in certain cases they render different results. Present paper summarizes and compares the abovementioned analytical and numerical approaches for determining critical loads and it exemplarily analyses corresponding cantilever beam capacities using numerical approaches based on plastic zones theory (GMNIA).}, subject = {Tr{\"a}ger}, language = {en} } @article{BecherGenaAlsaadetal., author = {Becher, Lia and Gena, Amayu Wakoya and Alsaad, Hayder and Richter, Bernhard and Spahn, Claudia and V{\"o}lker, Conrad}, title = {The spread of breathing air from wind instruments and singers using schlieren techniques}, series = {Indoor Air}, volume = {2021}, journal = {Indoor Air}, number = {volume 31, issue 6}, publisher = {Wiley Blackwell}, address = {Oxford}, doi = {10.1111/ina.12869}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220209-45817}, pages = {1798 -- 1814}, abstract = {The spread of breathing air when playing wind instruments and singing was investigated and visualized using two methods: (1) schlieren imaging with a schlieren mirror and (2) background-oriented schlieren (BOS). These methods visualize airflow by visualizing density gradients in transparent media. The playing of professional woodwind and brass instrument players, as well as professional classical trained singers were investigated to estimate the spread distances of the breathing air. For a better comparison and consistent measurement series, a single high note, a single low note, and an extract of a musical piece were investigated. Additionally, anemometry was used to determine the velocity of the spreading breathing air and the extent to which it was quantifiable. The results showed that the ejected airflow from the examined instruments and singers did not exceed a spreading range of 1.2 m into the room. However, differences in the various instruments have to be considered to assess properly the spread of the breathing air. The findings discussed below help to estimate the risk of cross-infection for wind instrument players and singers and to develop efficacious safety precautions, which is essential during critical health periods such as the current COVID-19 pandemic.}, subject = {Covid-19}, language = {en} } @article{LegatiukGuerlebeckHommel, author = {Legatiuk, Anastasiia and G{\"u}rlebeck, Klaus and Hommel, Angela}, title = {Estimates for the discrete fundamental solution of the discrete Laplace operator on a rectangular lattice}, series = {Mathematical Methods in the Applied Sciences}, volume = {2021}, journal = {Mathematical Methods in the Applied Sciences}, publisher = {Wiley}, address = {Chichester}, doi = {10.1002/mma.7747}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220209-45829}, pages = {1 -- 23}, abstract = {This paper presents numerical analysis of the discrete fundamental solution of the discrete Laplace operator on a rectangular lattice. Additionally, to provide estimates in interior and exterior domains, two different regularisations of the discrete fundamental solution are considered. Estimates for the absolute difference and lp-estimates are constructed for both regularisations. Thus, this work extends the classical results in the discrete potential theory to the case of a rectangular lattice and serves as a basis for future convergence analysis of the method of discrete potentials on rectangular lattices.}, subject = {diskrete Fourier-Transformation}, language = {en} } @article{IbanezKraus, author = {Ibanez, Stalin and Kraus, Matthias}, title = {A Numerical Approach for Plastic Cross Cross-Sectional Analyses of Steel Members}, series = {ce/papers}, volume = {2021}, journal = {ce/papers}, number = {Volume 4, issue 2-4}, publisher = {Ernst \& Sohn, a Wiley brand}, address = {Berlin}, doi = {10.1002/cepa.1527}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20220112-45622}, pages = {2098 -- 2106}, abstract = {Global structural analyses in civil engineering are usually performed considering linear-elastic material behavior. However, for steel structures, a certain degree of plasticization depending on the member classification may be considered. Corresponding plastic analyses taking material nonlinearities into account are effectively realized using numerical methods. Frequently applied finite elements of two and three-dimensional models evaluate the plasticity at defined nodes using a yield surface, i.e. by a yield condition, hardening rule, and flow rule. Corresponding calculations are connected to a large numerical as well as time-consuming effort and they do not rely on the theoretical background of beam theory, to which the regulations of standards mainly correspond. For that reason, methods using beam elements (one-dimensional) combined with cross-sectional analyses are commonly applied for steel members in terms of plastic zones theories. In these approaches, plasticization is in general assessed by means of axial stress only. In this paper, more precise numerical representation of the combined stress states, i.e. axial and shear stresses, is presented and results of the proposed approach are validated and discussed.}, subject = {Stahlkonstruktion}, language = {en} }