@inproceedings{MuellerLudwig, author = {M{\"u}ller, Matthias and Ludwig, Horst-Michael}, title = {Sulfatangriff magnesiumhaltiger W{\"a}sser auf M{\"o}rtel unterschiedlicher Zusammensetzung}, series = {Tagungsband 18. Ibausil - 18. Internationale Baustofftagung : 12.-15. September 2012, Weimar}, booktitle = {Tagungsband 18. Ibausil - 18. Internationale Baustofftagung : 12.-15. September 2012, Weimar}, editor = {Ludwig, Horst-Michael}, organization = {F.A.Finger-Institut f{\"u}r Baustoffkunde, Bauhaus-Universit{\"a}t Weimar}, isbn = {978-3-00-034075-8 (Bauhaus-Universit{\"a}tsverlag Weimar)}, doi = {10.25643/bauhaus-universitaet.4873}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20240507-48732}, pages = {489-496}, abstract = {Die besondere Aggressivit{\"a}t von hochkonzentrierten Magnesiumsulfatl{\"o}sungen bei Einwirkung auf Beton ist seit vielen Jahrzehnten bekannt. Neben dem Sulfat greift zus{\"a}tzlich auch das Magnesium den Zementstein an. Bei hohen L{\"o}sungskonzentrationen nimmt der Magnesiumangriff gegen{\"u}ber dem Sulfatangriff sogar eine dominante Rolle ein. Magnesiumgehalte unter 300 mg/l im Grundwasser gelten allerdings bislang als nicht angreifend. In Auslagerungs- und Laborversuchen wurde jedoch festgestellt, dass auch bei praxisrelevanten Magnesium- (<300 mg/l) und Sulfatgehalten (1.500 mg/l) das Magnesium zu einer deutlichen Versch{\"a}rfung des Sulfatangriffes bei niedrigen Temperaturen f{\"u}hrte. Diese Versch{\"a}rfung trat bei M{\"o}rteln und Betonen auf, bei denen der erh{\"o}hte Sulfatwiderstand durch einen teilweisen Zementersatz mit 20 \% Flugasche zu einem CEM II/A-LL erreicht werden sollte, gem{\"a}ß der Flugascheregelung nach EN 206-1/DIN 1045-2. Bei einem teilweisen Zementersatz durch 30 \% Flugasche konnte auch in magnesiumhaltigen Sulfatl{\"o}sungen eine deutliche Verbesserung des Sulfatwiderstandes erreicht werden. M{\"o}rtel mit HS-Zement als Bindemittel wiesen keinerlei Sch{\"a}den auf. Schadensverursachend war eine Kombination mehrerer Einfl{\"u}sse. Zum einen wurde der Sulfatwiderstand des Zement-Flugasche-Systems durch die unzureichende Reaktion der Flugasche infolge der niedrigen Lagerungstemperatur geschw{\"a}cht. Zum anderen konnte durch die Einwirkung des Magnesiums in der Randzone vermutlich eine Destabilisierung der C-S-H-Phasen erfolgen, wodurch die Thaumasitbildung an dieser Stelle forciert wurde. Zus{\"a}tzlich wurde durch den Portlanditverbrauch und die pH-Wert-Absenkung in der Randzone die puzzolanische Reaktion der Flugasche behindert.}, subject = {Beton}, language = {de} } @inproceedings{MuellerEhrhardtLudwig, author = {M{\"u}ller, Matthias and Ehrhardt, Dirk and Ludwig, Horst-Michael}, title = {Optimierung der Nachbehandlung von Waschbetonoberfl{\"a}chen}, series = {Tagungsband 18. Ibausil - 18. Internationale Baustofftagung : 12.-15. September 2012, Weimar}, booktitle = {Tagungsband 18. Ibausil - 18. Internationale Baustofftagung : 12.-15. September 2012, Weimar}, editor = {Ludwig, Horst-Michael}, organization = {F.A.Finger-Institut f{\"u}r Baustoffkunde, Bauhaus-Universit{\"a}t Weimar}, isbn = {978-3-00-034075-8}, doi = {10.25643/bauhaus-universitaet.4872}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20240226-48722}, pages = {794-781}, abstract = {Der Nachbehandlung eines Fahrbahndeckenbetons kommt zum Erzielen eines hohen Frost-Tausalz-Widerstandes der fertigen Betondecke eine besondere Bedeutung zu. Bei der Waschbetonbauweise erfolgt die Nachbehandlung in mehreren Schritten. Eine erste Nachbehandlung gew{\"a}hrleistet den Verdunstungsschutz des Betons bis zum Zeitpunkt des Ausb{\"u}rstens des verz{\"o}gerten Oberfl{\"a}chenm{\"o}rtels. Daran schließt sich die zweite Nachbehandlung an, in der Regel durch Aufspr{\"u}hen eines fl{\"u}ssigen Nachbehandlungsmittels. Der zweite Nachbehandlungsschritt ist entscheidend f{\"u}r den Frost-Tausalz-Widerstand der Betondecke. Im Rahmen eines Forschungsprojektes wurde daher untersucht, inwiefern durch eine Optimierung der zweiten Nachbehandlung der Frost-Tausalz-Widerstand von Waschbetonoberfl{\"a}chen erh{\"o}ht werden kann, insbesondere bei Verwendung h{\"u}ttensandhaltiger Zemente. Schon durch eine einmalige Nassnachbehandlung wurde eine deutlich h{\"o}herer Widerstand der Waschbetons gegen Frost-Tausalz-Angriff erzielt.}, subject = {Beton}, language = {de} } @periodical{OPUS4-4848, title = {Schwerpunkt Kollektiv}, volume = {2012}, number = {3.2012, Heft 2}, editor = {Engell, Lorenz and Siegert, Bernhard}, publisher = {Felix Meiner Verlag}, address = {Hamburg}, organization = {Internationales Kolleg f{\"u}r Kulturtechnikforschung und Medienphilosophie}, issn = {2366-0767}, doi = {10.28937/ZMK-3-2}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20240507-48485}, pages = {208}, abstract = {Die neuere und h{\"o}chst produktive Konjunktur des »Kollektiv«-Begriffs in Soziologie und Kulturtheorie, wie sie sich insbesondere durch die Ent-faltung der Akteur-Netzwerk-Theorie herausgebildet hat, ist zun{\"a}chst durch vier miteinander zusammenh{\"a}ngende Eigent{\"u}mlichkeiten gekennzeichnet. Erstens bezeichnet das »Kollektiv« in diesem Sinne vor allem anderen eine Ansammlung von Entit{\"a}ten zu einem als Ganzem operativen, m{\"o}glicherweise sogar handlungs- und reflexionsf{\"a}higen Komplex. Die Operationen werden dabei erstens im »Kollektiv« und durch das »Kollektiv« ausgef{\"u}hrt, gleichzeitig jedoch sind sie es, die das »Kollektiv« {\"u}berhaupt erst aufspannen und relationieren und so zusammenhalten und reproduzieren bzw. variieren. Das Besondere daran ist zweitens - und das unterscheidet den »Kollektiv«-Begriff etwa von demjenigen des Systems -, dass es keine Subsumption der beteiligten Entit{\"a}ten unter das kollektive Gebilde gibt. Die Operationsf{\"a}higkeit und der Zusammenschluss f{\"u}hren weder zu einem Aufgehen des Einzelnen im Ganzen, noch zerf{\"a}llt im R{\"u}ckfall das Ganze in eine bloße Gesamtheit aufsummierbarer Teile und Effekte. Kurz: Das »Kollektiv« kann nicht {\"u}ber die Beziehung von Ganzem und Teil definiert und schon gar nicht nach einer dieser beiden Seiten hin aufgel{\"o}st werden. Drittens, und das ist der vermutlich plakativste Zug des neuen »Kollektiv«-Begriffs, umfasst das »Kollektiv« Entit{\"a}ten v{\"o}llig heterogener Art, genauer: Es bringt solche Gegebenheiten zusammen, die nach klassischer ontologischer Tradition verschiedenen Seinsbezirken zugerechnet worden w{\"a}ren. Das sind vor allem die ber{\"u}hmten menschlichen und nichtmenschlichen Akteure Bruno Latours, das sind also Personen und Artefakte, Kultur- und Naturdinge, Intelligibles und Sensibles, Reflexives und Irreflexives, Technisches und {\"A}sthetisches, Bilder und Objekte oder sogar Materielles und Immaterielles wie Geister, G{\"o}tter und Ahnen, so bei Descola oder Gell. Und viertens schließlich ist der »Kollektiv«-Begriff speziell ein Kontrastbegriff , der innerhalb der »neuen Soziologie« der Akteur-Netzwerk-Theorie an die Stelle des Gesellschaftsbegriff s treten soll, eben um dessen humanozentrische Pr{\"a}gung einerseits und seine subsumptive, generalisierende und anti-partikulare Tradition andererseits abzustreifen.}, subject = {Medienwissenschaft}, language = {de} } @periodical{OPUS4-4847, title = {Schwerpunkt Entwerfen}, volume = {2012}, number = {3.2012, Heft 1}, editor = {Engell, Lorenz and Siegert, Bernhard}, publisher = {Felix Meiner Verlag}, address = {Hamburg}, organization = {Internationales Kolleg f{\"u}r Kulturtechnikforschung und Medienphilosophie}, issn = {2366-0767}, doi = {10.28937/ZMK-3-1}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20240507-48473}, pages = {225}, abstract = {Entwerfen ist ein {\"a}usserst unscharfer Begriff. Mit ihm kann je nach Kontext ebenso Zeichnen, Planen, Modellieren, Projektieren oder Darstellen gemeint sein wie Erfi nden, Entwickeln, Konzipieren, Komponieren und {\"a}hnliches. Wenn Architekten vom Entwurf reden, verwenden sie das Wort meist in einer Bedeutung, die auf den kunsttheoretischen Diskurs zur{\"u}ckgeht, der im Florenz des 16. Jahrhunderts entstanden ist: Entwurf als disegno. Dementsprechend konnte Entwerfen in der kunsthermeneutischen Rezeption schließlich mit dem ›k{\"u}nstlerischen Schaff ensprozess‹ selbst synonym werden. Im Entwerfen meint man der geistigen Verm{\"o}gen und Prozesse im k{\"u}nstlerischen Subjekt habhaft zu werden. An diese Tradition soll hier bewusst nicht angekn{\"u}pft werden. Um das Entwerfen als Kulturtechnik in seiner historischen Bedingtheit zu beschreiben, muss es aus dem anthropozentrischen Ursprung herausger{\"u}ckt werden, an den es der florentinische kunsttheoretische Diskurs versetzt hat. Statt das Entwerfen als fundamentalen Akt k{\"u}nstlerischen Schaff ens zu begreifen und als anthropologische Konstante der Geschichte zu entziehen, w{\"a}re eben diese Konzeption als historisches Resultat von diskursiven, technischen und institutionellen Praktiken zu befragen.}, subject = {Medienwissenschaft}, language = {de} } @article{TalebiZiSilanietal., author = {Talebi, Hossein and Zi, Goangseup and Silani, Mohammad and Samaniego, Esteban and Rabczuk, Timon}, title = {A simple circular cell method for multilevel finite element analysis}, series = {Journal of Applied Mathematics}, journal = {Journal of Applied Mathematics}, doi = {10.1155/2012/526846}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170426-31639}, abstract = {A simple multiscale analysis framework for heterogeneous solids based on a computational homogenization technique is presented. The macroscopic strain is linked kinematically to the boundary displacement of a circular or spherical representative volume which contains the microscopic information of the material. The macroscopic stress is obtained from the energy principle between the macroscopic scale and the microscopic scale. This new method is applied to several standard examples to show its accuracy and consistency of the method proposed.}, subject = {Finite-Elemente-Methode}, language = {en} } @article{HildebrandHechtBliedtneretal., author = {Hildebrand, J{\"o}rg and Hecht, Kerstin and Bliedtner, Jens and M{\"u}ller, Hartmut}, title = {Advanced Analysis of Laser Beam Polishing of Quartz Glass Surfaces}, series = {Physics Procedia}, journal = {Physics Procedia}, doi = {10.1016/j.phpro.2012.10.039}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170418-31372}, pages = {277 -- 285}, abstract = {The laser beam is a small, flexible and fast polishing tool. With laser radiation it is possible to finish many outlines or geometries on quartz glass surfaces in the shortest possible time. It's a fact that the temperature developing while polishing determines the reachable surface smoothing and, as a negative result, causes material tensions. To find out which parameters are important for the laser polishing process and the surface roughness respectively and to estimate material tensions, temperature simulations and extensive polishing experiments took place. During these experiments starting and machining parameters were changed and temperatures were measured contact-free. The accuracy of thermal and mechanical simulation was improved in the case of advanced FE-analysis.}, subject = {Laser}, language = {en} } @article{Aguinaga, author = {Aguinaga, Jos{\´e} Guillermo De}, title = {Error in prediction due to data type availability in a coupled hydro-mechanical model}, series = {Electronic Journal of Geotechnical Engineering}, journal = {Electronic Journal of Geotechnical Engineering}, doi = {10.25643/bauhaus-universitaet.3117}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170413-31170}, pages = {2459 -- 2471}, abstract = {Different types of data provide different type of information. The present research analyzes the error on prediction obtained under different data type availability for calibration. The contribution of different measurement types to model calibration and prognosis are evaluated. A coupled 2D hydro-mechanical model of a water retaining dam is taken as an example. Here, the mean effective stress in the porous skeleton is reduced due to an increase in pore water pressure under drawdown conditions. Relevant model parameters are identified by scaled sensitivities. Then, Particle Swarm Optimization is applied to determine the optimal parameter values and finally, the error in prognosis is determined. We compare the predictions of the optimized models with results from a forward run of the reference model to obtain the actual prediction errors. The analyses presented here were performed calibrating the hydro-mechanical model to 31 data sets of 100 observations of varying data types. The prognosis results improve when using diversified information for calibration. However, when using several types of information, the number of observations has to be increased to be able to cover a representative part of the model domain. For an analysis with constant number of observations, a compromise between data type availability and domain coverage proves to be the best solution. Which type of calibration information contributes to the best prognoses could not be determined in advance. The error in model prognosis does not depend on the error in calibration, but on the parameter error, which unfortunately cannot be determined in inverse problems since we do not know its real value. The best prognoses were obtained independent of calibration fit. However, excellent calibration fits led to an increase in prognosis error variation. In the case of excellent fits; parameters' values came near the limits of reasonable physical values more often. To improve the prognoses reliability, the expected value of the parameters should be considered as prior information on the optimization algorithm.}, subject = {Sensitivit{\"a}tsanalyse}, language = {en} } @inproceedings{Wudtke, author = {Wudtke, Idna}, title = {CONSTITUTIVE MODELING OF CRYSTALLINE MATERIALS WITH TEXTURE CHARACTERISTICS}, series = {Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar}, booktitle = {Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar}, editor = {G{\"u}rlebeck, Klaus and Lahmer, Tom and Werner, Frank}, organization = {Bauhaus-Universit{\"a}t Weimar}, issn = {1611-4086}, doi = {10.25643/bauhaus-universitaet.2791}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170314-27910}, pages = {9}, abstract = {The analysis of the response of complex structural systems requires the description of the material constitutive relations by means of an appropriate material model. The level of abstraction of such model may strongly affect the quality of the prognosis of the whole structure. In context to this fact, it is necessary to describe the material in a convenient sense as exact but as simple as possible. All material phenomena of crystalline materials e.g. steel, affecting the behavior of the structure, rely on physical effects which are interacting over spatial scales from subatomic to macroscopic range. Nevertheless, if the material is microscopically heterogenic, it might be appropriate to use phenomenological models for the purpose of civil engineering. Although constantly applied, these models are insufficient for steel materials with microscopic characteristics such as texture, typically occurring in hot rolled steel members or heat affected zones of welded joints. Hence, texture is manifested in crystalline materials as a regular crystallographic structure and crystallite orientation, influencing macroscopic material properties. The analysis of structural response of material with texture (e.g. rolled steel or heat affected zone of a welded joint) obliges the extension of the phenomenological material description of macroscopic scale by means of microscopic information. This paper introduces an enrichment approach for material models based on a hierarchical multiscale methodology. This has been done by describing the grain texture on a mesoscopic scale and coupling it with macroscopic constitutive relations by means of homogenization. Due to a variety of available homogenization methods, the question of an assessment of coupling quality arises. The applicability of the method and the effect of the coupling method on the reliability of the response are presented on an example.}, subject = {Angewandte Informatik}, language = {en} } @inproceedings{MusialKamińskiUbysz, author = {Musial, Michal and Kamiński, Mieczysław and Ubysz, Andrzej}, title = {DISCRETE CRACK MODEL OF BORCZ FOR CALCULATING THE DEFLECTIONS OF BENDING REINFORCED CONCRETE BEAM}, series = {Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar}, booktitle = {Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar}, editor = {G{\"u}rlebeck, Klaus and Lahmer, Tom and Werner, Frank}, organization = {Bauhaus-Universit{\"a}t Weimar}, issn = {1611-4086}, doi = {10.25643/bauhaus-universitaet.2790}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170314-27907}, pages = {11}, abstract = {In the design of the reinforced concrete beams loaded by the bending moment, it is assumed that the structure can be used at a level of load, that there are local discontinuities - cracks. Designing the element demands checking two limit states of construction, load capacity and usability. Limit states usability include also the deflection of the element. Deflections in the reinforced concrete beams with cracks are based on actual rigidity of the element. After cracking there is a local change in rigidity of the beam. The rigidity is variable in the element's length and due to the heterogeneous structure of concrete, it is not possible to clearly describe those changes. Most standards of testing methods tend to simplify the calculations and take the average value of the beam's rigidity on its entire length. The rigidity depends on the level of the maximal load of the beam. Experimental researches verify the value by inserting the coefficients into the formulas used in the theory of elasticity. The researches describe the changes in rigidity in the beam's length more precisely. The authors take into consideration the change of rigidity, depending on the level of maximum load (continuum models), or localize the changes in rigidity in the area of the cracks (discrete models). This paper presents one of the discrete models. It is distinguished by the fact that the left side of the differential equation, that depends on the rigidity, is constant, and all effects associated with the scratches are taken as the external load and placed on the right side of the equation. This allows to generalize the description. The paper presents a particular integral of the differential equation, which allow analyzing the displacement and vibration for different rigidity of the silo's walls, the flow rate and type of the flowing material.}, subject = {Angewandte Informatik}, language = {en} } @inproceedings{MusialUbyszUlatowski, author = {Musial, Michal and Ubysz, Andrzej and Ulatowski, Piotr}, title = {MODEL DESCRIBING STATIC AND DYNAMIC DISPLACEMENTS OF SILOS WALL DURING THE FLOW OF LOOSE MATERIAL}, series = {Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar}, booktitle = {Digital Proceedings, International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering : July 04 - 06 2012, Bauhaus-University Weimar}, editor = {G{\"u}rlebeck, Klaus and Lahmer, Tom and Werner, Frank}, organization = {Bauhaus-Universit{\"a}t Weimar}, issn = {1611-4086}, doi = {10.25643/bauhaus-universitaet.2789}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170314-27896}, pages = {16}, abstract = {Correct evaluation of wall displacements is a key matter when designing silos. This issue is important from both the standpoint of design engineer (load-bearing capacity of structures) and end-consumer (durability of structures). Commonplace methods of silo design mainly focus on satisfying limit states of load-bearing capacity. Current standards fail to specify methods of dynamic displacements analysis. Measurements of stressacting on silo walls prove that the actual stress is sum of static and dynamic stresses. Janssen came up with differential equation describing state of static equilibrium in cross-section of a silo. By solving the equation static stress of granular solid on silo walls can be determined. Equations of motion were determined from equilibrium equations of feature objects. General solution, describing dynamic stresses was presented as parametric model. This paper presents particular integrals of differential equation, which enable analysing displacements and vibrations for different rigidities of silo walls, types of granular solid and its flow rate.}, subject = {Angewandte Informatik}, language = {en} }