@inproceedings{DjordjevicPetkovicZivkovic,
  author    = {Djordjevic, Djordje and Petkovic, Dusan and Zivkovic, Darko},
  title     = {THE APPLICATION OF INTERVAL CALCULUS TO ESTIMATION OF PLATE DEFLECTION BY SOLVING POISSON'S PARTIAL DIFFERENTIAL EQUATION},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  issn      = {1611-4086},
  doi       = {10.25643/bauhaus-universitaet.2839},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170314-28397},
  pages     = {12},
  abstract  = {This paper describes the application of interval calculus to calculation of plate deflection, taking in account inevitable and acceptable tolerance of input data (input parameters). The simply supported reinforced concrete plate was taken as an example. The plate was loaded by uniformly distributed loads. Several parameters that influence the plate deflection are given as certain closed intervals. Accordingly, the results are obtained as intervals so it was possible to follow the direct influence of a change of one or more input parameters on output (in our example, deflection) values by using one model and one computing procedure. The described procedure could be applied to any FEM calculation in order to keep calculation tolerances, ISO-tolerances, and production tolerances in close limits (admissible limits). The Wolfram Mathematica has been used as tool for interval calculation.},
  subject      = {Angewandte Informatik},
  language  = {en}
}
@inproceedings{DoganArditiGunaydin,
  author    = {Dogan, Sevgi Zeynep and Arditi, D. and Gunaydin, H. Murat},
  title     = {COMPARISON OF ANN AND CBR MODELS FOR EARLY COST PREDICTION OF STRUCTURAL SYSTEMS},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  doi       = {10.25643/bauhaus-universitaet.2942},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29421},
  abstract  = {Reasonably accurate cost estimation of the structural system is quite desirable at the early stages of the design process of a construction project. However, the numerous interactions among the many cost-variables make the prediction difficult. Artificial neural networks (ANN) and case-based reasoning (CBR) are reported to overcome this difficulty. This paper presents a comparison of CBR and ANN augmented by genetic algorithms (GA) conducted by using spreadsheet simulations. GA was used to determine the optimum weights for the ANN and CBR models. The cost data of twenty-nine actual cases of residential building projects were used as an example application. Two different sets of cases were randomly selected from the data set for training and testing purposes. Prediction rates of 84\% in the GA/CBR study and 89\% in the GA/ANN study were obtained. The advantages and disadvantages of the two approaches are discussed in the light of the experiments and the findings. It appears that GA/ANN is a more suitable model for this example of cost estimation where the prediction of numerical values is required and only a limited number of cases exist. The integration of GA into CBR and ANN in a spreadsheet format is likely to improve the prediction rates.},
  subject      = {Architektur <Informatik>},
  language  = {en}
}
@article{DonathPetzold1997,
  author    = {Donath, Dirk and Petzold, Frank},
  title     = {Zuk{\"u}nftige Techniken f{\"u}r eine computergest{\"u}tzte Planungspraxis - applikative Tools f{\"u}r die architektonische Bestandserfassung},
  doi       = {10.25643/bauhaus-universitaet.496},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20111215-4962},
  year      = {1997},
  abstract  = {Der Beitrag beschreibt die Entwicklung eines Softwaresystems zur strukturierten Erfassung und Verwaltung bestehender Geb{\"a}ude in der Architektur. Die Erfassung erfolgt durch die Aufnahme von geometrischen Daten und Sachdaten in unterschiedlichen Abstraktionsstufen unter Einbeziehung einer vorangehenden Dekomposition. Basis f{\"u}r die Entwicklung eines solchen Systems ist die Analyse und Systematik der Erfassungstechniken, -abl{\"a}ufe und der Gegenstand der architektonischen Bestandsaufnahme. Parallel hierzu erfolgt die Bewertung und Nutzung aktueller Techniken und Werkzeuge der applikativen Informatik. Schwerpunkte der Forschungsarbeit sind die Ableitung einer allgemeinen Geb{\"a}ude- und Bauteilstruktur, die Einbeziehung aktueller informationstechnischer Verfahren und Werkzeuge und die Entwicklung eines entsprechenden Experimentalsystems. Auf eine Auswahl softwaretechnischer Entwicklungen wird n{\"a}her eingegangen (objektspezifische Eigenschaften, flexible Geometrieerfassung und Benutzeroberfl{\"a}chen).},
  subject      = {Bauaufnahme},
  language  = {de}
}
@inproceedings{DudekRichter,
  author    = {Dudek, Mariusz and Richter, Matthias},
  title     = {UNTERSUCHUNGEN ZUR ZUVERL{\"A}SSIGKEIT DES STRAßENBAHNNETZES IN KRAKAU},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  doi       = {10.25643/bauhaus-universitaet.2943},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29432},
  pages     = {19},
  abstract  = {Der Begriff der Zuverl{\"a}ssigkeit spielt eine zentrale Rolle bei der Bewertung von Verkehrsnetzen. Aus der Sicht der Nutzer des {\"o}ffentlichen Personennahverkehrs ({\"O}PNV) ist eines der wichtigsten Kriterien zur Beurteilung der Qualit{\"a}t des Liniennetzes, ob es m{\"o}glich ist, mit einer großen Sicherheit das Reiseziel in einer vorgegebenen Zeit zu erreichen. Im Vortrag soll dieser Zuverl{\"a}ssigkeitsbegriff mathematisch gefasst werden. Dabei wird zun{\"a}chst auf den {\"u}blichen Begriff der Zuverl{\"a}ssigkeit eines Netzes im Sinne paarweiser Zusammenhangswahrscheinlichkeiten eingegangen. Dieser Begriff wird erweitert durch die Betrachtung der Zuverl{\"a}ssigkeit unter Einbeziehung einer maximal zul{\"a}ssigen Reisezeit. In vergangenen Arbeiten hat sich die Ring-Radius-Struktur als bew{\"a}hrtes Modell f{\"u}r die theoretische Beschreibung von Verkehrsnetzen erwiesen. Diese {\"U}berlegungen sollen nun durch Einbeziehung realer Verkehrsnetzstrukturen erweitert werden. Als konkretes Beispiel dient das Straßenbahnnetz von Krakau. Hier soll insbesondere untersucht werden, welche Auswirkungen ein geplanter Ausbau des Netzes auf die Zuverl{\"a}ssigkeit haben wird. This paper is involved with CIVITAS-CARAVEL project: "Clean and better transport in cites". The project has received research funding from the Community's Sixth Framework Programme. The paper reflects only the author's views and the Community is not liable for any use that may be made of the information contained therein.},
  subject      = {Architektur <Informatik>},
  language  = {de}
}
@inproceedings{DzwigonHempel,
  author    = {Dzwigon, Wieslaw and Hempel, Lorenz},
  title     = {ZUR SYNCHRONISATION VON LINIEN IM {\"O}PNV},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  doi       = {10.25643/bauhaus-universitaet.2944},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29442},
  pages     = {12},
  abstract  = {Wir betrachten im {\"O}PNV ({\"O}ffentlichen Personennahverkehr) diejenige Situation, daß zwei Bus- oder Straßenbahnlinien gemeinsame Haltestellen haben. Ziel unserer Untersuchungen ist es, f{\"u}r beide Linien einen solchen Fahrplan zu finden, der f{\"u}r die Fahrg{\"a}ste m{\"o}glichst viel Bequemlichkeit bietet. Die Bedarfsstruktur - die Anzahl von Personen, die die beiden Linien benutzen - setzt dabei gewisse Beschr{\"a}nkungen f{\"u}r die Taktzeiten der beiden Linien. Die verbleibenden Entscheidungsfreiheiten sollen im Sinne der Zielstellung ausgenutzt werden. Im Vortrag wird folgenden Fragen nachgegangen: - nach welchen Kriterien kann man die "Bequemlichkeit" oder die "Synchonisationsg{\"u}te" messen? - wie kann man die einzelnen "Synchronisationsmaße" berechnen ? - wie kann man die verbleibenden Entscheidungsfreiheiten nutzen, um eine m{\"o}glichst gute Synchronisation zu erreichen ? Die Ergebnisse werden dann auf einige Beispiele angewandt und mit den bereitgestellten Methoden L{\"o}sungsvorschl{\"a}ge unterbreitet.},
  subject      = {Architektur <Informatik>},
  language  = {de}
}
@inproceedings{EbertLenzen,
  author    = {Ebert, Carsten and Lenzen, Armin},
  title     = {OUTPUT-ONLY ANALYSIS FOR EXPERIMENTAL DAMAGE DETECTION OF A TIED-ARCH BRIDGE},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  doi       = {10.25643/bauhaus-universitaet.2945},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29452},
  pages     = {13},
  abstract  = {In civil engineering it is very difficult and often expensive to excite constructions such as bridges and buildings with an impulse hammer or shaker. This problem can be avoided with the output-only method as special feature of stochastic system identification. The permanently existing ambient noise (e.g. wind, traffic, waves) is sufficient to excite the structures in their operational conditions. The output-only method is able to estimate the observable part of a state-space-model which contains the dynamic characteristics of the measured mechanical system. Because of the assumption that the ambient excitation is white there is no requirement to measure the input. Another advantage of the output-only method is the possibility to get high detailed models by a special method, called polyreference setup. To pretend the availability of a much larger set of sensors the data from varying sensor locations will be collected. Several successive data sets are recorded with sensors at different locations (moving sensors) and fixed locations (reference sensors). The covariance functions of the reference sensors are bases to normalize the moving sensors. The result of the following subspace-based system identification is a high detailed black-box-model that contains the weighting function including the well-known dynamic parameters eigenfrequencies and mode shapes of the mechanical system. Emphasis of this lecture is the presentation of an extensive damage detection experiment. A 53-year old prestressed concrete tied-arch-bridge in H{\"u}nxe (Germany) was deconstructed in 2005. Preliminary numerous vibration measurements were accomplished. The first experiment for system modification was an additional support near the bridge bearing of one main girder. During a further experiment one hanger from one tied arch was cut through as an induced damage. Some first outcomes of the described experiments will be presented.},
  subject      = {Architektur <Informatik>},
  language  = {en}
}
@inproceedings{EbertBernsteinCerejeirasetal.,
  author    = {Ebert, Svend and Bernstein, Swanhild and Cerejeiras, Paula and K{\"a}hler, Uwe},
  title     = {NONZONAL WAVELETS ON S^N},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  issn      = {1611-4086},
  doi       = {10.25643/bauhaus-universitaet.2840},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170314-28406},
  pages     = {18},
  abstract  = {In the present article we will construct wavelets on an arbitrary dimensional sphere S^n due the approach of approximate Identities. There are two equivalently approaches to wavelets. The group theoretical approach formulates a square integrability condition for a group acting via unitary, irreducible representation on the sphere. The connection to the group theoretical approach will be sketched. The concept of approximate identities uses the same constructions in the background, here we select an appropriate section of dilations and translations in the group acting on the sphere in two steps. At First we will formulate dilations in terms of approximate identities and than we call in translations on the sphere as rotations. This leads to the construction of an orthogonal polynomial system in L²(SO(n+1)). That approach is convenient to construct concrete wavelets, since the appropriate kernels can be constructed form the heat kernel leading to the approximate Identity of Gauss-Weierstra\ss. We will work out conditions to functions forming a family of wavelets, subsequently we formulate how we can construct zonal wavelets from a approximate Identity and the relation to admissibility of nonzonal wavelets. Eventually we will give an example of a nonzonal Wavelet on \$S^n\$, which we obtain from the approximate identity of Gauss-Weierstraß.},
  subject      = {Angewandte Informatik},
  language  = {en}
}
@inproceedings{EblingScheuermann,
  author    = {Ebling, Julia and Scheuermann, G.},
  title     = {TEMPLATE MATCHING ON VECTOR FIELDS USING CLIFFORD ALGEBRA},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  doi       = {10.25643/bauhaus-universitaet.2946},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29464},
  pages     = {25},
  abstract  = {Due to the amount of flow simulation and measurement data, automatic detection, classification and visualization of features is necessary for an inspection. Therefore, many automated feature detection methods have been developed in recent years. However, only one feature class is visualized afterwards in most cases, and many algorithms have problems in the presence of noise or superposition effects. In contrast, image processing and computer vision have robust methods for feature extraction and computation of derivatives of scalar fields. Furthermore, interpolation and other filter can be analyzed in detail. An application of these methods to vector fields would provide a solid theoretical basis for feature extraction. The authors suggest Clifford algebra as a mathematical framework for this task. Clifford algebra provides a unified notation for scalars and vectors as well as a multiplication of all basis elements. The Clifford product of two vectors provides the complete geometric information of the relative positions of these vectors. Integration of this product results in Clifford correlation and convolution which can be used for template matching of vector fields. For frequency analysis of vector fields and the behavior of vector-valued filters, a Clifford Fourier transform has been derived for 2D and 3D. Convolution and other theorems have been proved, and fast algorithms for the computation of the Clifford Fourier transform exist. Therefore the computation of Clifford convolution can be accelerated by computing it in Clifford Fourier domain. Clifford convolution and Fourier transform can be used for a thorough analysis and subsequent visualization of flow fields.},
  subject      = {Architektur <Informatik>},
  language  = {en}
}
@inproceedings{EckardtKoenke,
  author    = {Eckardt, Stefan and K{\"o}nke, Carsten},
  title     = {ENERGY RELEASE CONTROL FOR NONLINEAR MESOSCALE SIMULATIONS},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  issn      = {1611-4086},
  doi       = {10.25643/bauhaus-universitaet.2841},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170314-28414},
  pages     = {5},
  abstract  = {In nonlinear simulations the loading is, in general, applied in an incremental way. Path-following algorithms are used to trace the equilibrium path during the failure process. Standard displacement controlled solution strategies fail if snap-back phenomena occur. In this contribution, a path-following algorithm based on the dissipation of the inelastic energy is presented which allows for the simulation of snap-backs. Since the constraint is defined in terms of the internal energy, the algorithm is not restricted to continuum damage models. Furthermore, no a priori knowledge about the final damage distribution is required. The performance of the proposed algorithm is illustrated using nonlinear mesoscale simulations.},
  subject      = {Angewandte Informatik},
  language  = {en}
}
@inproceedings{EckardtKoenke,
  author    = {Eckardt, Stefan and K{\"o}nke, Carsten},
  title     = {ADAPTIVE SIMULATION OF THE DAMAGE BEHAVIOR OF CONCRETE USING HETEROGENEOUS MULTISCALE MODELS},
  editor    = {G{\"u}rlebeck, Klaus and K{\"o}nke, Carsten},
  organization    = {Bauhaus-Universit{\"a}t Weimar},
  doi       = {10.25643/bauhaus-universitaet.2947},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:wim2-20170327-29478},
  pages     = {15},
  abstract  = {In this paper an adaptive heterogeneous multiscale model, which couples two substructures with different length scales into one numerical model is introduced for the simulation of damage in concrete. In the presented approach the initiation, propagation and coalescence of microcracks is simulated using a mesoscale model, which explicitly represents the heterogeneous material structure of concrete. The mesoscale model is restricted to the damaged parts of the structure, whereas the undamaged regions are simulated on the macroscale. As a result an adaptive enlargement of the mesoscale model during the simulation is necessary. In the first part of the paper the generation of the heterogeneous mesoscopic structure of concrete, the finite element discretization of the mesoscale model, the applied isotropic damage model and the cohesive zone model are briefly introduced. Furthermore the mesoscale simulation of a uniaxial tension test of a concrete prism is presented and own obtained numerical results are compared to experimental results. The second part is focused on the adaptive heterogeneous multiscale approach. Indicators for the model adaptation and for the coupling between the different numerical models will be introduced. The transfer from the macroscale to the mesoscale and the adaptive enlargement of the mesoscale substructure will be presented in detail. A nonlinear simulation of a realistic structure using an adaptive heterogeneous multiscale model is presented at the end of the paper to show the applicability of the proposed approach to large-scale structures.},
  subject      = {Architektur <Informatik>},
  language  = {en}
}