TY - THES A1 - Hildebrand, Jörg T1 - Numerische Schweißsimulation - Bestimmung von Temperatur, Gefüge und Eigenspannung an Schweißverbindungen aus Stahl- und Glaswerkstoffen T1 - Numerical welding simulation - determination of temperature, microstructure and residual stress for steel and glass materials in welded joints N2 - Die Komplexität des Schweißprozesses und das Verhalten der Werkstoffe infolge des Energieeintrages erfordern eine umfassende Betrachtungsweise. Die Entwicklung von numerischen Modellen und Methoden in den letzten 50 Jahren ermöglicht die Simulation, Analyse und Optimierung von Schweißverbindungen hinsichtlich Temperatur, Gefügestruktur und Eigenspannungen. Eine Differenzierung der Schweißsimulation in Prozess-, Werkstoff- und Struktursimulation gestattet eine gezielte Untersuchung von einzelnen Aspekten. Diese Unterteilung erfordert zum Teil eine starke Abstraktion und Idealisierung der Realität durch geeignete Annahmen und Randbedingungen, die von der zu untersuchenden Fragestellung abhängen. Dadurch wird eine Kalibrierung und Verifikation der Modelle mit Versuchsergebnissen notwendig. Die in dieser Arbeit durchgeführten Untersuchungen beschäftigen sich mit wichtigen Fragestellungen hinsichtlich der numerischen Simulation und experimentellen Untersuchung des Temperaturfeldes sowie des Gefüge- und Eigenspannungszustandes von MAG-Schweißverfahren an den Werkstoffen Feinkornbaustahl und Duplex-Stahl, CO2-Laserstrahlschweißverfahren am Werkstoff Quarzglas, Trennprozessen von Proben, WIG-Nachbehandlungsverfahren. Hinsichtlich der Naht- und Stoßarten orientierte sich die Arbeit an baupraktisch relevanten Schweißverbindungen sowie Besonderheiten, die sich aus Schweißprozessen und unterschiedlichen Werkstoffen ergeben. Eine Interpretation der numerisch und experimentell ermittelten Ergebnisse ermöglicht die Ableitung von allgemeingültigen Erkenntnissen zur Ausbildung des Temperaturfeldes, Entstehung von Gefügestrukturen und Eigenspannungen. Voraussetzungen für eine realitätsnahe Schweißsimulation zur Bestimmung von Temperatur, Gefügeanteil und Eigenspannung sind neben den Geometriemodellen geeignete numerische Modelle für die Einkopplung der Energie aus dem Schweißprozess und für die Abgabe der Energie durch Konvektion und Strahlung an die Umgebung, zur Beschreibung des thermischen und mechanischen Werkstoffverhaltens im Bereich von Raumtemperatur bis zur Schmelztemperatur. N2 - In the last 50 years simulation, analysis and optimization of welded joints makes the development possible of numerical models and methods for determination of temperature, microstructure and residual stress. A differentiation of welding simulation in process, material and structural simulation is possible for a purposeful investigation of individual aspects. This partitioning requires a strong abstraction and idealization of the reality with boundary conditions. Calibrations and verifications of the models with test results are necessary. The investigations concern with important questions in regard to the numerical simulation and experimental investigation of temperature field as well as microstructure and residual stresses of MAG-welding at the materials fine-grain structural steel and duplex steel, CO2-laser welding at the material quartz glass, separation processes of samples, post welding process with TIG. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 18 KW - MAG-Schweißen KW - Schweißen KW - Simulation KW - Eigenspannung KW - Feinkornbaustahl KW - Quarzglas KW - Schweißverbindung KW - Wärmeeinflusszone KW - Laserschweißen KW - Ferri KW - welding KW - numerical simulation KW - residual stress KW - joints KW - steel Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20090617-14753 ER - TY - THES A1 - Heidolf, Thorsten T1 - Zeit- und beanspruchungsabhängiges Tragverhalten von polymermodifiziertem Beton unter mehrfach wiederholter Beanspruchung T1 - Time- and Strain-Dependent Behaviour of Polymer-Modified Concrete with Multifariously Repeated Load N2 - In der vorliegenden Arbeit werden die experimentellen Ergebnisse eigener Untersuchungen an unbewehrtem und bewehrtem polymermodifiziertem Beton unter mehrfach wiederholter Druck- und Zugbeanspruchung vorgestellt und mit den Ergebnissen ähnlicher Versuche an Normalbeton und hochfestem Beton verglichen. Besondere Aufmerksamkeit wird dabei dem Formänderungsverhalten, der Steifigkeitsdegradation und der Energiedissipation sowie dem Kriechverhalten und der Mitwirkung des Betons zwischen den Rissen gewidmet. Die beobachtete signifikante Steifigkeitsdegradation sowie der ausgeprägt nichtlineare Zusammenhang zwischen der viskosen Verformung und der elastischen Stauchung zeigen, dass bei der Analyse der Kriech¬aus¬wirkungen des polymermodifizierten Betons auf das Tragverhalten entsprechender Kon¬struktionen neben den Gebrauchslasten auch die während der Lastgeschichte aufgetretenen maximalen Beanspruchungssituationen sowie die damit verbundenen Strukturveränderungen zu berücksichtigen sind. Auf der Basis der Versuchsergebnisse und der visko-elastisch-plastischen Kontinuumsschädigungstheorie werden rheologische Modelle zur Beschreibung des zeit- und beanspruchungsabhängigen Tragverhaltens von Betonbauteile vorgeschlagen. Die numerische Umsetzung der vorgeschlagenen Modelle erfolgt unter Berücksichtigung des zeitabhängigen Materialverhaltens des Betons auf der Basis des HAMILTON-Prinzips unter Vernachlässigung der Trägheitskräfte. Durch eine zeitliche Diskretisierung kann die Problembeschreibung auf das Prinzip von LAGRANGE vom Minimum des Gesamtpotentials zurückgeführt und als nichtlineare Optimierungsaufgabe formuliert werden. Die Simulation des beanspruchungsabhängigen Tragverhaltens von Stahlbetonverbundquerschnitten verdeutlicht die Qualität und Leistungsfähigkeit der vorgeschlagenen Modellbildung. N2 - The experimental results of the investigations into polymer-modified concrete with multifariously repeated compression or tension load are introduced in the provided work and compared to similar experiments in normal- and high-strength concrete. Special attention is dedicated to the stress-strain relation, the degradation of stiffness and the dissipation of energy as well as the non-linear long-term behaviour and tension-stiffening. Stiffness degradation and non-linear creep of polymer-modified concrete show that maximum strain situations have to be taken into consideration of the behaviour analysis of concrete structures under long-term loading. Based on experimental results and the theory of visco-elastic-plastic continuum damage, rheological models are suggested for the description of the time- and damage-dependent behaviour of reinforced concrete. The numerical concept is based on the HAMILTON-principle. Using time discretisation, mechanical modelling simplifies and can be described as a LAGRANGE-principle concerning minimum of total potential energy. The problem is solved by non-linear optimisation. The efficiency of the suggested model was proven for reinforced concrete cross sections by numerical simulation. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 10 KW - Kriechen KW - Kunstharzmodifizierter Zementbeton KW - Beton KW - Tragverhalten KW - Bruchverhalten KW - Experiment KW - Deformationsverhalten KW - Stoffgesetz KW - nichtlineare Optimierung KW - Simulation KW - Formänderungsenergie KW - Steifigkeitsdegradation KW - Creep KW - damage KW - tension-stiffening KW - dissipation of energy KW - non-linear optimisation Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20080102-11753 SN - 978-3-86068-331-2 ER - TY - JOUR A1 - van Treeck, Christoph A1 - Rank, Ernst T1 - Analysis of building structure and topology based on Graph Theory N2 - Individual views on a building product of people involved in the design process imply different models for planning and calculation. In order to interpret these geometrical, topological and semantical data of a building model we identify a structural component graph, a graph of room faces, a room graph and a relational object graph as aids and we explain algorithms to derive these relations. The application of the technique presented is demonstrated by the analysis and discretization of a sample model in the scope of building energy simulation. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Graphentheorie KW - Ingenieurbau Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2308 ER - TY - THES A1 - Grosse, Marco T1 - Zur numerischen Simulation des physikalisch nichtlinearen Kurzzeittragverhaltens von Nadelholz am Beispiel von Holz-Beton-Verbundkonstruktionen T1 - On the numerical simulation of the nonlinear short-time carrying behaviour of softwood with application to timber-concrete composite structures N2 - In der Arbeit wird ein räumliches Materialmodell für den anisotropen Werkstoff Holz vorgestellt. Dessen Leistungsfähigkeit wird durch Verifikationsrechnungen und die Simulation eigener Versuche aufgezeigt. In diesen Versuchen wurde das Tragverhalten spezieller Schubverbindungselemente der Brettstapel-Beton-Verbundbauweise untersucht. Die Kombination eines Brettstapels mit einer schubfest angeschlossenen Betonplatte ist eine vorteilhafte Möglichkeit, Schnittholz mit geringem Querschnitt effektiv in biegebeanspruchten Bauteilen einzusetzen. Es werden die Ergebnisse der experimentellen Untersuchungen zu den Schubverbindungselementen Flachstahlschloss und Nutverbindung vorgestellt. Diese zeichnen sich durch eine über die gesamte Plattenbreite kontinuierliche Übertragung der Schubkraft per Kontaktpressung aus. Vor allem in Brettstapel-Beton-Verbunddecken werden somit ein sehr hoher Verschiebungsmodul sowie eine eminente Tragfähigkeit erreicht. Um mit numerischen Strukturanalysen die in den Versuchen beobachteten Versagensmechanismen adäquat abbilden und realistische Prognosen für das Tragverhalten von Bauteilen oder Verbindungen treffen zu können, muss das physikalisch nichtlineare Verhalten aller beteiligter Baustoffe in die Berechnungen einbezogen werden. Im Rahmen der Dissertation wurde ein auf der Plastizitätstheorie basierendes Materialmodell für Nadelholz hergeleitet und in das FE-Programm ANSYS implementiert, welches die Mikrostruktur des Holzes als verschmierendes Ersatzkontinuum erfasst. Anhand des anatomischen Aufbaus des inhomogenen, anisotropen und porigen Werkstoffs werden die holzspezifischen Versagensmechanismen und die daraus abgeleiteten konstitutiven Beziehungen erläutert. Das ausgeprägt anisotrope Tragverhalten von Holz ist vor allem durch erstaunliche Duktilität bei Stauchung, sprödes Versagen bei Zug- und Schubbeanspruchung und enorme Festigkeitsunterschiede in den Wuchsrichtungen gekennzeichnet. Die Auswirkungen der größtenteils unabhängig voneinander auftretenden, mikromechanischen Versagensmechanismen auf die Spannungs-Verformungsbeziehungen wurden durch die Formulierung adäquater Ver- resp. Entfestigungsfunktionen in Abhängigkeit der Beanspruchungsmodi erfasst. Das dem Materialmodell zu Grunde liegende mehrflächige Fließkriterium berücksichtigt die Interaktion aller sechs Komponenten des räumlichen Spannungszustandes. Die durchgeführten Verifikations- und Simulationsberechnungen belegen, dass der erarbeitete Ansatz sowohl zur Bewertung des Tragvermögens als auch zur Beurteilung von Riss- bzw. Schädigungsursachen von Holzbauteilen eingesetzt werden kann. Die numerische Simulation eröffnet neue, bisher wenig beachtete Möglichkeiten zur Untersuchung komplexer Holzstrukturen sowie Anschlussdetails und wird sich auf Grund der Aussagekraft und Flexibilität auch im Ingenieurholzbau mehr und mehr gegenüber ausschließlich experimenteller Untersuchung durchsetzen. N2 - In the dissertation a spatial model for the anisotropic, porous material wood is presented. The efficiency of this numerical approach is pointed out by verifying computations and simulations of own experiments. In these tests the load carrying behaviour of special joining techniques for laminated timber concrete composite constructions have been examined. The combination of a laminated timber element with a shear resistant joined concrete slab is a profitable alternative for effectively using lumber with small cross section in bending stressed members. The results of the experimental investigations of flat-steel-lock and notch connection are presented. These are characterised by a load transmission via contact pressure continuously over the entire slab width. Particularly in laminated timber concrete composite ceilings a very stiff load-deflection relationship as well as an eminent load-carrying capacity is reached. To simulate the structural behaviour of members and to model there failure mechanisms it is necessary to take the mechanically nonlinear behaviour in the critical and post critical range of all involved materials into account. For this reason a constitutive material model for timber based on the plasticity theory was implemented in the finite element code ANSYS. The basic multisurface yield criterion considers the interaction of all six components of the spatial stress state. The proposal is furthermore based on the classic continuum mechanics. Therefore, a crack is not described discretely, but by its effect on the stress deformation behaviour. The numerical model reproduces the wood-specific anisotropic, load dependent strengths as well as predominantly independent proceeding of strain hardening and, respectively, softening. The conducted verifications and simulations prove, that the designed approach can be applied to the evaluation of the load-carrying behaviour as well as crack and damage causes of timber components. The numerical simulation opens new potentialities for investigation of complex wooden structures as well as connection details. Compared with expensive experimental studies this procedure will gain more significance due to its expressiveness and flexibility even in timber engineering. T3 - Schriftenreihe des Instituts für Konstruktiven Ingenieurbau - 7 KW - Holzbau KW - Verbundbauweise KW - Beton KW - Nichtlineare Finite-Elemente-Methode KW - Plastizitätstheorie KW - Numerische Mathematik KW - Simulation KW - Nichtlineare Kon KW - Holz-Beton-Verbund KW - HBV KW - Versagensmechanismen KW - Brettstapel KW - timber concrete composite KW - laminated timber Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20060215-7725 ER - TY - JOUR A1 - Gao, Zuoren A1 - Wu, Weiyu A1 - Ren, Aizhu T1 - Physically Based Modeling and Multi-Physical Simulation System for Wood Structure Fire Performance N2 - This research is devoted to promoting the performance-based engineering in wood structure fire. It looks into the characteristic of the material, structural composing and collapse detecting to find out the main factors in the wood structure collapse in fire. The aim of the research is to provide an automatic simulation platform for the complicated circulation. A physically based model for slim member for beams and columns and a frame of multi-physical simulation are provided to implement the system. The physically based model contains material model, structural mechanics model, material mechanics model, as well as geometry model for the compositive simulation. The multi-physical simulation is built on the model and has the capacity to carry out a simulation combining structural, fire (thermal, CFD) and material degradation simulation. The structural and fire simulation rely on two sophisticated software respectively, ANSYS (an FEA software) and FDS (with a core of CFD). Researchers of the paper develop system by themselves to combine the two existing ones. The system has the capability to calculate the wood char to find out the loss of cross-section and to detect the collapse caused in different ways. The paper gives a sample of Chinese traditional house to show how this simulation system works. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Holzbau KW - Brandschutz Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2381 ER - TY - JOUR A1 - Kang, Shihchung A1 - Miranda, Eduardo T1 - Automated Simulation of the Erection Activities in Virtual Construction N2 - The goal of the research is the development of a computer system to plan, simulate and visualize erection processes in construction. In the research construction cranes are treated as robots with predefined degrees of freedom and crane-specific motion planning techniques are developed to generate time-optimized and collision-free paths for each piece to be erected in the project. Using inverse kinematics and structural dynamics simulation, the computer system then computes the crane motions and velocities necessary to achieve the previously calculated paths. The main benefits of the research are the accurate planning and scheduling of crane operations leading to optimization of crane usage and project schedules, as well as improving overall crane safety in the project. This research is aimed at the development of systems that will allow computer-assisted erection of civil infrastructure and ultimately to achieve fully-automated erection processes using robotic cranes... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Baukonstruktion KW - Virtuelle Realität Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2310 ER - TY - JOUR A1 - Neuberg, Frank A1 - Fank, Ernst A1 - Ekkerlein, Christian T1 - Integrated Life Cycle Simulation and Assessment of Buildings N2 - Buildings require both for construction and, due to their comparatively long life cycle for maintenance, significant raw material and energy resources. So far available knowledge about resource consumption during an entire life cycle of a building is still quite rare, because various criteria affect each other and/or overlay mutually. In this contribution a model based software concept is presented using an integrated approach for life cycle simulation and assessment of buildings. The essential point of the development consists of connecting an IFC compliant product model of a building via the Internet with data bases for the resource and energy requirement of building materials. Furthermore, numerical simulations allow calculating and minimizing the energy consumption, the resource requirement, the waste streams and also the noxious emissions. In the context of this paper we present the first release of software programs for architects and engineers, which help them to evaluate their design decisions objectively in early planning steps. Additionally the usage of the software is demonstrated by a test case study for a real world building. By applying this software in practice a substantial contribution for saving energy and natural resources can be provided in the sense of sustainable and ecological building design. KW - Produktmodell KW - Simulation KW - Bautechnik KW - Lebenszyklus Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2351 ER - TY - CHAP A1 - Gebbeken, Norbert A1 - Baumhauer, Andreas A1 - Ionita, Mihai T1 - Increasing the Reliability and Performance through Automatization and Parallel Working N2 - Re-examination of the behaviour of structures can be necessary due to deterioration or changes in the traffic situation during their lifetime. The Finite Element Method (FEM) is widely used in order to accomplish numerical analysis. Considering the development of computer performance, more detailed FEM models can be analyzed, even on site, with mobile computers. To compensate the increasing amount of data needed for the model input, measures need to be taken to save time, by distributing the work. In order to provide consistency to the model, fedback data must be checked upon reception. A local wireless computer network of ultra-portable devices linked together with a computer can provide the coordination necessary for efficient parallel working. Based on a digital model consisting of all data gathered, structural modelling and numerical analysis are performed automatically. Thus, the user is released from the work that can be automatized and the time needed for the overall analysis of a structure is decreased. KW - Ingenieurbau KW - Verteiltes System KW - Planungsprozess KW - Modellierung KW - Parallelverarbeitung KW - Simulation Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-1397 ER - TY - JOUR A1 - Semenov, Vitaly A1 - Alekseeva, Elena A1 - Tarlapan, Oleg T1 - Virtual Construction using Map-based Approach N2 - The paper presents a general map-based approach to prototyping of products in virtual reality environments. Virtual prototyping of products is considered as a consistent simulation and visualization process mapping the source product model into its target visual representations. The approach enables to interrelate formally the product and visual information models with each other by defining mapping rules, to specify a prototyping scenario as a composition of map instances, and then to explore particular product models in virtual reality environments by interpreting the composed scenario. Having been realized, the proposed approach provides for the strongly formalized method and the common software framework to build virtual prototyping applications. As a result, the applications gain in expressiveness, reusability and reliability, as well as take on additional runtime flexibility... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Virtuelle Realität KW - Bauwerk Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2447 ER - TY - JOUR A1 - Kiviniemi, Arto A1 - Fischer, Martin T1 - Requirements Management Interface to Building Product Models N2 - In current AEC practice client requirements are typically recorded in a building program, which, depending on the building type, covers various aspects from the overall goals, activities and spatial needs to very detailed material and condition requirements. This documentation is used as the starting point of the design process, but as the design progresses, it is usually left aside and changes are made incrementally based on the previous design solution. These incremental small changes can lead to a solution that may no longer meet the original requirements. In addition, design is by nature an iterative process and the proposed solutions often also cause evolution in the client requirements. However, the requirements documentation is usually not updated accordingly. Finding the latest updates and evolution of the requirements from the documentation is very difficult, if not impossible. This process can lead to an end result, which is significantly different from the documented requirements. Some important requirements may not be satisfied, and even if the design process was based on agreed-upon changes in the scope and requirements, differences in the requirements documents and in the completed building can lead to well-justified doubts about the quality of the design and construction process... KW - Produktmodell KW - Simulation KW - Bautechnik KW - Bauwerk KW - Modellierung Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20111215-2427 ER -