TY - THES A1 - Partschefeld, Stephan T1 - Synthese von Fließmitteln aus Stärke und Untersuchung der Wechselwirkung mit Portlandzement N2 - Das Ziel dieser Arbeit war es, neuartige Fließmittel auf Basis von Stärke als nachwachsenden Rohstoff zu synthetisieren und die Wechselwirkung mit Portlandzement zu charakterisieren. Die Notwendigkeit, Alternativen zu synthetischen Zusatzmittel zu erforschen, ergibt sich aus der benötigten Menge zur Verarbeitung von ca. 4,1 Gt/a, wobei ca. 85 % der Zusatzmittel auf die Fließmittel entfallen. Um Fließmittel aus Stärke zu synthetisieren, wurden drei Basisstärken unterschiedlicher Herkunft verwendet. Es wurde eine Maniokstärke mit einer niedrigen Molekularmasse und eine Weizenstärke mit einer hohen Molekularmasse verwendet. Darüber hinaus wurde eine Kartoffelstärke mit einer mittleren Molekularmasse, die ein Abfallprodukt der kartoffelverarbeitenden Industrie darstellt, genutzt. Die Stärkefließmittel wurden durch chemische Modifikation in einem zweistufigen Prozess synthetisiert. Im ersten Schritt wurde das Molekulargewicht der Weizen- und Kartoffelstärke durch säurehydrolytischen Abbau verringert. Für die kurzkettige Maniokstärke war eine Degradation der Molekularmasse nicht notwendig. Im zweiten Syntheseschritt wurden anionische Ladungen durch das Versetzen der degradierten Stärken und Maniokstärke mit Natriumvinylsulfonat in die Stärkemoleküle eingeführt. Beurteilung der Synthesemethode zur Erzeugung von Stärkefließmitteln In diesem Zusammenhang sollten molekulare Parameter der Stärkefließmittel gezielt eingestellt werden, um eine Fließwirkung im Portlandzement zu erhalten. Insbesondere die Molekularmasse und die Menge anionischer Ladungen sollte variiert werden, um Abhängigkeiten mit der Dispergierleistung zu identifizieren. 1. Es konnte durch GPC-Messungen gezeigt werden, dass die Molekularmasse der langkettigen Weizenstärke durch die gewählten Modifizierungsbedingungen zum säurehydrolytischen Abbau verringert werden konnte. Durch Variation der säurehydrolytischen Bedingungen wurden 4 degradierte Weizenstärken erzeugt, die eine Reduzierung der Molekularmasse um 27,5 – 43 % aufwiesen. Die Molekularmasse der Kartoffelstärke konnte durch säurehydrolytischen Abbau um ca. 26 % verringert werden. 2. Durch PCD-Messungen wurde gezeigt, dass anionische Ladungen durch Sulfoethylierung der freien Hydroxylgruppen in die degradierten Stärken eingeführt werden konnten. Durch Variation der Dauer der Sulfoethylierung konnte die Menge der anionischen Ladungen gesteuert und gezielt variiert werden, so dass Stärkefließmittel mit steigender Ladungsmenge in folgender Reihenfolge synthetisiert wurden: W-3 < W-2 < K-1 < W¬-4 < W¬1 < M-1 Im Ergebnis der chemischen Modifizierung konnten 6 Stärkefließmittel mit variierten Molekularmassen und anionischen Ladungen erzeugt werden. Es konnte gezeigt werden, dass die Herkunft der Stärke für die chemische Modifizierung unerheblich ist. Die Fließmittel lagen synthesebedingt als basische, wässrige Suspensionen mit Wirkstoffgehalten im Bereich von 23,5 – 50 % vor. Beurteilung der Dispergierleistung der synthetisierten Stärkefließmittel Die Dispergierperformance wurde durch rheologische Experimente mit einem Rotationsviskosimeter erfasst. Dabei wurden der Einfluss auf die Fließkurven und die Viskositätskurven betrachtet. Durch Vergleich der Dispergierleistung mit einem Polykondensat- und einem PCE-Fließmittel konnte eine Einordnung und Bewertung der Fließmittel vorgenommen werden. 3. Die rheologische Experimente haben gezeigt, dass die Stärkefließmittel eine vergleichbar hohe Dispergierleistung aufweisen, wie das zum Vergleich herangezogen PCE-Fließmittel. Darüber hinaus zeigte sich, dass die Fließwirkung der 6 Stärkefließmittel gegenüber dem Polykondensatfließmittel deutlich höher ist. Das aus der Literatur bekannte Einbrechen der Dispergierleistung der Polykondensat-fließmittel bei w/z-Werten < 0,4 konnte bestätigt werden. 4. Alle 6 Stärkefließmittel führten zu einer Verringerung der Fließgrenze und der dynamischen Viskosität des Zementleimes bei einem w/z-Wert von 0,35. 5. Der Vergleich der Dispergierleistung der Stärkefließmittel untereinander zeigte, dass die anionische Ladungsmenge einen Schlüsselparameter darstellt. Die Stärkefließmittel M-1, K-1, W-1 und W-4 mit anionischen Ladungsmengen > 6 C/g zeigten die höchste Dispergier¬performance. Die vergleichend herangezogenen klassischen Fließmittel wiesen anionische Ladungsmengen im Bereich von 1,2 C/g (Polycondensat) und 1,6 C/g (PCE) auf. Die Molekularmasse schien für die Dispergierleistung zunächst unerheblich zu sein. Aus diesem Grund wurde die Basisweizenstärke erneut chemisch modifiziert, indem anionische Ladungen eingeführt wurden, ohne die Molekularmasse jedoch zu verringern. Das Stärkederivat wies verdickende Eigenschaften im Zementleim auf. Daraus konnte geschlussfolgert werden, dass eine definierte Grenzmolekularmasse (150.000 Da) existiert, die unterschritten werden muss, um Fließmittel aus Stärke zu erzeugen. Des Weiteren zeigen die Ergebnisse, dass durch die chemische Modifizierung sowohl Fließmittel als auch Verdicker aus Stärke erzeugt werden können. Beurteilung der Beeinflussung der Hydratation und der Porenlösung des Portlandzementes Aus der Literatur ist bekannt, dass Fließmittel die Hydratation von Portlandzement maßgeblich beeinflussen können. Aus diesem Grund wurden kalorimetrische und konduktometrische Untersuchungen an Zementsuspensionen, die mit den synthetisierten Stärkefließmitteln versetzt wurden, durchgeführt. Ergänzt wurden die Untersuchungen durch Porenlösungsanalysen zu verschiedenen Zeitpunkten der Hydratation. 6. Die kalorimetrischen Untersuchungen zur Beeinflussung der Hydratation des Portlandzementes zeigten, dass die dormante Periode durch die Zugabe der Stärkefließmittel z.T. erheblich verlängert wird. Es konnte gezeigt werden, dass, je höher die anionische Ladungsmenge der Stärkefließmittel ist, desto länger dauert die dormante Periode andauert. Darüber hinaus zeigte sich, dass eine niedrige Molekularmasse der Stärkefließmittel die Verlängerung der dormanten Periode begünstigt. 7. Durch die konduktometrischen Untersuchungen konnte gezeigt werden, dass alle Stärkefließmittel die Dauer des freien- und diffusionskontrollierten CSH-Phasenwachstums verlangsamen. Insbesondere die Ausfällung des Portlandits, welches mit dem Erstarrungsbeginn korreliert, erfolgt zu deutlich späteren Zeitpunkten. Des Weiteren korrelierten die konduktometrischen Untersuchungen mit der zeitlichen Entwicklung der Calciumkonzentration der Porenlösungen. Der Vergleich der Stärkefließmittel untereinander zeigte, dass die Molekularmasse ein Schlüsselparameter ist. Das Stärkefließmittel M-1 mit der geringsten Molekularmasse, welches geringe Mengen kurzkettiger Anhydroglucoseeinheiten aufweist, verzögert die Hydratphasenbildung am stärksten. Diese Wirkung ist vergleichbar mit der von Zuckern. Darüber hinaus deuteten die Ergebnisse daraufhin, dass die Stärkefließmittel auf den ersten Hydratationsprodukten adsorbieren, wodurch die Hydratphasenbildung verlangsamt wird. Die kalorimetrischen und konduktometrischen Daten sowie die Ergebnisse der Porenlösungsanalytik des Zementes, erforderten eine genauere Betrachtung der Beeinflussung der Hydratation der Klinkerphasen C3A und C3S, durch die Stärkefließmittel. Demzufolge wurden die Untersuchungen mit den Klinkerphasen C3A und C3S in Analogie zum Portlandzement durchgeführt. Beurteilung der Beeinflussung der Hydratation und der Porenlösung des C3A Während die kalorimetrischen Untersuchungen zur C3A-Hydratation eine Tendenz zur verlangsamten Hydratphasenbildung durch die Stärkefließmittel aufzeigten, lieferten die konduktometrischen Ergebnisse grundlegende Erkenntnisse zur Beeinflussung der C3A-Hydratation. Das Stadium I der C3A-Hydratation ist durch einen Abfall der elektrischen Leitfähigkeit geprägt. Dies korreliert mit dem Absinken der Calciumionenkonzentration und dem Anstieg der Aluminiumionenkonzentration in der Porenlösung der C3A-Suspensionen. Im Anschluss an das Stadium I bildet sich ein Plateau in den elektrischen Leitfähigkeitskurven aus. 8. Es konnte gezeigt werden, dass die Stärkefließmittel das Stadium I der C3A-Hydratation, d.h. die Auflösung und Bildung erster Calciumaluminathydrate verlangsamen. Insbesondere die Stärkefließmittel mit höherer Molekularmasse erhöhten die Dauer des Stadium I. Das Stadium II wird durch die Stärkefließmittel in folgender Reihenfolge am stärksten verlängert: M-1 > W-3 > K-1 > W-2 ≥ W-4 und verdeutlicht, dass keine Abhängigkeit von der anionischen Ladungsmenge identifiziert werden konnte. Die Ergebnisse zeigten, dass speziell die kurzkettige Stärke M-1, das Stadium II länger aufrechterhalten. 9. Das Stadium III und IV der C3A-Hydratation wird insbesondere durch die Stärkefließmittel mit höherer Molekularmasse verlängert. Die Ergebnisse der Porenlösungsanalytik korrelieren mit den Ergebnissen der elektrischen Leitfähigkeit. Speziell die zeitlichen Verläufe der Calciumionenkonzentration bildeten die Verläufe der Konduktivitätskurven der C3A-Hydratation mit großer Übereinstimmung ab. Beurteilung der Beeinflussung der Hydratation und der Porenlösung des C3S Die Ergebnisse der kalorimetrischen Untersuchungen zur Beeinflussung der C3S-Hydratation durch die Stärkefließmittel zeigen, dass diese maßgeblich verlangsamt wird. Das Maximum des Haupthydratationspeaks wird zu späteren Zeiten verschoben und auch die Höhe des Maximums wird deutlich verringert. Durch die konduktometrischen Experimente wurde aufgeklärt, welche Stadien der C3S-Hydrataion beeinflusst wurden. 10. Es konnte gezeigt werden, dass sowohl die Menge der eingebrachten anionischen Ladungen als auch das Vorhandensein sehr kleiner Stärkefließmittelmoleküle (Zucker), Schlüsselparameter der verzögerten Hydratationskinetik des C3S sind. Der grundlegende Mechanismus der Hydratationsverzögerung beruht auf einer Kombination aus verminderter CSH-Keimbildung und Adsorptionsprozessen auf den ersten gebildeten CSH-Phasen der C3S-Partikel. Beurteilung des Adsorptionsverhaltens am Zement, C3A und C3S Die Bestimmung des Adsorptionsverhaltens der Stärkefließmittel erfolgte mit der Phenol-Schwefelsäure-Methode an Zement,- C3A- und C3S-Suspensionen. Durch den Vergleich der Adsorptionsraten und Adsorptionsmengen in Abhängigkeit von den molekularen Parametern der Stärkefließmittel wurde ein Wechselwirkungsmodell identifiziert. 11. Die Ursache für die hohe Dispergierleistung der Stärkefließmittel liegt in Adsorptionsprozessen an den ersten gebildeten Hydratphasen des Zementes begründet. Die Molekularmasse der Stärkefließmittel ist ein Schlüsselparameter der entscheidend für den Mechanismus der Adsorption ist. Während anionische, langkettige Stärken an mehreren Zementpartikeln gleichzeitig adsorbieren und für eine Vernetzung der Zementpartikel untereinander sorgen (Verdickerwirkung), adsorbieren kurzkettige anionische Stärken lediglich an den ersten gebildeten Hydratphasen der einzelnen Zementpartikel und führen zu elektrostatischer Abstoßung (Fließmittelwirkung). 12. Es konnte gezeigt werden, dass die Stärkefließmittel mit geringerem Molekulargewicht bei höheren Konzentrationen an den Hydratphasen des Zementes adsorbieren. Die Stärkefließmittel mit höherer Molekularmasse erreichen bei einer Zugabemenge von 0,7 % ein Plateau. Daraus wird geschlussfolgert, dass die größeren Fließmittelmoleküle einen erhöhten Platzbedarf erfordern und zur Absättigung der hydratisierenden Oberflächen bei geringeren Zugabemengen führen. Darüber hinaus konnte gezeigt werden, dass die Stärkefließmittel mit höherer anionischer Ladungsmenge zu höheren Adsorptionsmengen auf den Zement-, C3A- und C3S-Partikeln führen. 13. Die Adsorptionsprozesse finden an den ersten gebildeten Hydratphasen der C3A-Partikel statt, wodurch sowohl die Auflösung des C3A als auch die Bildung der Calciumhydroaluminate verlangsamt wird. Darüber hinaus wurde festgestellt, dass die Verlangsamung des freien- und diffusionskontrollierten Hydratphasenwachstums des C3S, durch die Adsorption der Stärkefließmittel auf den ersten gebildeten CSH-Phasen hervorgerufen wird. Des Weiteren wurde festgestellt, dass sehr kleine zuckerähnliche Moleküle in der kurzkettigen Maniokstärke in der Lage sind, die Bildung der ersten CSH-Keime zu unterdrücken. Dadurch kann die langanhaltende Plateauphase der elektrischen Leitfähigkeit der C3S-Hydratation erklärt werden. Beurteilung der Porenstruktur- und Festigkeitsausbildung Die Beurteilung der Qualität der Mikrostruktur erfolgte durch die Bestimmung der Rohdichte und der Porenradienverteilung mit Hilfe der Quecksilberhochdruckporosimetrie. Durch das Versetzen der Zementleime mit den Stärkefließmitteln konnten bei gleichbleibender Verarbeitbarkeit Zementsteinprobekörper mit einem um 17,5 % geringeren w/z-Wert von 0,35 hergestellt werden. Die Absenkung des w/z-Wertes führt zu einem Anstieg der Rohdichte des Zementsteins. 14. Durch die Zugabe der Stärkefließmittel und den verringerten w/z-Wert wird die Porenstruktur der Zementsteinproben im Vergleich zum Referenzzementstein verfeinert, da die Gesamtporosität sinkt. Insbesondere der Kapillarporenanteil wird verringert und der Gelporenanteil erhöht. Im Unterschied zu den PCE-Fließmitteln führt die Zugabe der Stärkefließmittel zu keinem erhöhten Eintrag von Luftporen. Dies wiederum hat zur Folge, dass bei der Verwendung der Stärkefließmittel auf Entschäumer verzichtet werden kann. 15. Entsprechend der dichteren Zementsteinmatrix wurden für die Zementsteine mit den Stärkefließmitteln nach 7 d und 28 d, erhöhte Biegezug- und Druckfestigkeiten ermittelt. Insbesondere die 28 d Druckfestigkeit wurde durch den verringerten w/z-Wert um die Faktoren 3,5 - 6,6 erhöht. KW - Zusatzmittel KW - Fließmittel KW - Stärkefließmittel KW - Zementhydratation KW - Synthese KW - Bauchemie KW - Betonverflüssiger Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220505-46402 ER - TY - THES A1 - Liu, Bokai T1 - Stochastic multiscale modeling of polymeric nanocomposites using Data-driven techniques N2 - In recent years, lightweight materials, such as polymer composite materials (PNCs) have been studied and developed due to their excellent physical and chemical properties. Structures composed of these composite materials are widely used in aerospace engineering structures, automotive components, and electrical devices. The excellent and outstanding mechanical, thermal, and electrical properties of Carbon nanotube (CNT) make it an ideal filler to strengthen polymer materials’ comparable properties. The heat transfer of composite materials has very promising engineering applications in many fields, especially in electronic devices and energy storage equipment. It is essential in high-energy density systems since electronic components need heat dissipation functionality. Or in other words, in electronic devices the generated heat should ideally be dissipated by light and small heat sinks. Polymeric composites consist of fillers embedded in a polymer matrix, the first ones will significantly affect the overall (macroscopic) performance of the material. There are many common carbon-based fillers such as single-walled carbon nanotubes (SWCNT), multi-walled carbon nanotubes (MWCNT), carbon nanobuds (CNB), fullerene, and graphene. Additives inside the matrix have become a popular subject for researchers. Some extraordinary characters, such as high-performance load, lightweight design, excellent chemical resistance, easy processing, and heat transfer, make the design of polymeric nanotube composites (PNCs) flexible. Due to the reinforcing effects with different fillers on composite materials, it has a higher degree of freedom and can be designed for the structure according to specific applications’ needs. As already stated, our research focus will be on SWCNT enhanced PNCs. Since experiments are timeconsuming, sometimes expensive and cannot shed light into phenomena taking place for instance at the interfaces/interphases of composites, they are often complemented through theoretical and computational analysis. While most studies are based on deterministic approaches, there is a comparatively lower number of stochastic methods accounting for uncertainties in the input parameters. In deterministic models, the output of the model is fully determined by the parameter values and the initial conditions. However, uncertainties in the input parameters such as aspect ratio, volume fraction, thermal properties of fiber and matrix need to be taken into account for reliable predictions. In this research, a stochastic multiscale method is provided to study the influence of numerous uncertain input parameters on the thermal conductivity of the composite. Therefore, a hierarchical multi-scale method based on computational homogenization is presented in to predict the macroscopic thermal conductivity based on the fine-scale structure. In order to study the inner mechanism, we use the finite element method and employ surrogate models to conduct a Global Sensitivity Analysis (GSA). The SA is performed in order to quantify the influence of the conductivity of the fiber, matrix, Kapitza resistance, volume fraction and aspect ratio on the macroscopic conductivity. Therefore, we compute first-order and total-effect sensitivity indices with different surrogate models. As stochastic multiscale models are computational expensive, surrogate approaches are commonly exploited. With the emergence of high performance computing and artificial intelligence, machine learning has become a popular modeling tool for numerous applications. Machine learning (ML) is commonly used in regression and maps data through specific rules with algorithms to build input and output models. They are particularly useful for nonlinear input-output relationships when sufficient data is available. ML has also been used in the design of new materials and multiscale analysis. For instance, Artificial neural networks and integrated learning seem to be ideally for such a task. They can theoretically simulate any non-linear relationship through the connection of neurons. Mapping relationships are employed to carry out data-driven simulations of inputs and outputs in stochastic modeling. This research aims to develop a stochastic multi-scale computational models of PNCs in heat transfer. Multi-scale stochastic modeling with uncertainty analysis and machine learning methods consist of the following components: -Uncertainty Analysis. A surrogate based global sensitivity analysis is coupled with a hierarchical multi-scale method employing computational homogenization. The effect of the conductivity of the fibers and the matrix, the Kapitza resistance, volume fraction and aspect ratio on the ’macroscopic’ conductivity of the composite is systematically studied. All selected surrogate models yield consistently the conclusions that the most influential input parameters are the aspect ratio followed by the volume fraction. The Kapitza Resistance has no significant effect on the thermal conductivity of the PNCs. The most accurate surrogate model in terms of the R2 value is the moving least square (MLS). -Hybrid Machine Learning Algorithms. A combination of artificial neural network (ANN) and particle swarm optimization (PSO) is applied to estimate the relationship between variable input and output parameters. The ANN is used for modeling the composite while PSO improves the prediction performance through an optimized global minimum search. The thermal conductivity of the fibers and the matrix, the kapitza resistance, volume fraction and aspect ratio are selected as input parameters. The output is the macroscopic (homogenized) thermal conductivity of the composite. The results show that the PSO significantly improves the predictive ability of this hybrid intelligent algorithm, which outperforms traditional neural networks. -Stochastic Integrated Machine Learning. A stochastic integrated machine learning based multiscale approach for the prediction of the macroscopic thermal conductivity in PNCs is developed. Seven types of machine learning models are exploited in this research, namely Multivariate Adaptive Regression Splines (MARS), Support Vector Machine (SVM), Regression Tree (RT), Bagging Tree (Bag), Random Forest (RF), Gradient Boosting Machine (GBM) and Cubist. They are used as components of stochastic modeling to construct the relationship between the variable of the inputs’ uncertainty and the macroscopic thermal conductivity of PNCs. Particle Swarm Optimization (PSO) is used for hyper-parameter tuning to find the global optimal values leading to a significant reduction in the computational cost. The advantages and disadvantages of various methods are also analyzed in terms of computing time and model complexity to finally give a recommendation for the applicability of different models. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,3 KW - Polymere KW - Nanoverbundstruktur KW - multiscale KW - nanocomposite KW - stochastic KW - Data-driven Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220503-46379 ER - TY - THES A1 - Müller, Matthias T1 - Salt-frost Attack on Concrete - New Findings regarding the Damage Mechanism N2 - The reduction of the cement clinker content is an important prerequisite for the improvement of the CO2-footprint of concrete. Nevertheless, the durability of such concretes must be sufficient to guarantee a satisfactory service life of structures. Salt frost scaling resistance is a critical factor in this regard, as it is often diminished at increased clinker substitution rates. Furthermore, only insufficient long-term experience for such concretes exists. A high salt frost scaling resistance thus cannot be achieved by applying only descriptive criteria, such as the concrete composition. It is therefore to be expected, that in the long term a performance based service life prediction will replace the descriptive concept. To achieve the important goal of clinker reduction for concretes also in cold and temperate climates it is important to understand the underlying mechanisms for salt frost scaling. However, conflicting damage theories dominate the current State of the Art. It was consequently derived as the goal of this thesis to evaluate existing damage theories and to examine them experimentally. It was found that only two theories have the potential to describe the salt frost attack satisfactorily – the glue spall theory and the cryogenic suction theory. The glue spall theory attributes the surface scaling to the interaction of an external ice layer with the concrete surface. Only when moderate amounts of deicing salt are present in the test solution the resulting mechanical properties of the ice can cause scaling. However, the results in this thesis indicate that severe scaling also occurs at deicing salt levels, at which the ice is much too soft to damage concrete. Thus, the inability of the glue spall theory to account for all aspects of salt frost scaling was shown. The cryogenic suction theory is based on the eutectic behavior of salt solutions, which consist of two phases – water ice and liquid brine – between the freezing point and the eutectic temperature. The liquid brine acts as an additional moisture reservoir, which facilitates the growth of ice lenses in the surface layer of the concrete. The experiments in this thesis confirmed, that the ice formation in hardened cement paste increases due to the suction of brine at sub-zero temperatures. The extent of additional ice formation was influenced mainly by the porosity and by the chloride binding capacity of the hardened cement paste. Consequently, the cryogenic suction theory plausibly describes the actual generation of scaling, but it has to be expanded by some crucial aspects to represent the salt frost scaling attack completely. The most important aspect is the intensive saturation process, which is ascribed to the so-called micro ice lens pump. Therefore a combined damage theory was proposed, which considers multiple saturation processes. Important aspects of this combined theory were confirmed experimentally. As a result, the combined damage theory constitutes a good basis to understand the salt frost scaling attack on concrete on a fundamental level. Furthermore, a new approach was identified, to account for the reduced salt frost scaling resistance of concretes with reduced clinker content. T2 - Frost-Tausalz-Angriff auf Beton - Neue Erkenntnisse zum Schadensmechnismus KW - Beton KW - Frost KW - Concrete KW - Salt frost attack KW - Damage mechanism KW - Glue Spall KW - Cryogenic Suction Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20230103-48681 UR - https://e-pub.uni-weimar.de/opus4/frontdoor/index/index/docId/4502 N1 - Englische Fassung meiner deutschsprachigen Dissertation mit dem Titel "Frost-Tausalz-Angriff auf Beton - Neue Erkenntnisse zum Schadensmechnismus". ER - TY - THES A1 - Cicek, Burhan T1 - Revisiting vernacular technique: Engineering a low environmental impact earth stabilisation method N2 - The major drawbacks of earth as a construction material — such as its low water stability and moderate strength — have led mankind to stabilize earth. Different civilizations developed vernacular techniques mainly focussing on lime, pozzolan or gypsum stabilization. Recently, cement has become the most commonly used additive in earth stabilization as it improves the strength and durability of plain earth. Also, it is a familiar and globally available construction material. However, using cement as an additive reduces the environmental advantages of earth and run counter to global targets regarding the reduction of CO2 emissions. Alternatives to cement stabilization are currently neither efficient enough to reduce its environmental impact nor allow the possibility of obtaining better results than those of cement. As such, this thesis deals with the rediscovery of a reverse engineering approach for a low environmental impact earth stabilization technique, aiming to replace cement in earth stabilization. The first step in the method consists in a comprehensive review of earth stabilization with regards to earthen building standards and soil classification, which allows us to identify the research gap. The review showed that there is great potential in using other additives which result in similar improvements as those achieved by cement. However, the studies that have been conducted so far either use expansive soils, which are not suitable for earth constructions or artificial pozzolans that indirectly contribute to CO2 emissions. This is the main research gap. The key concept for the development in the second step of the method is to combine vernacular additives to both improve the strength and durability of plain earth and to reduce the CO2 emissions. Various earth-mixtures were prepared and both development and performance tests were done to investigate the performance of this technique. The laboratory analyses on mix-design have proven a high durability and the results show a remarkable increase in strength performance. Furthermore, a significant reduction in CO2 emissions in comparison to cement stabilization could be shown. The third step of the method discusses the results drawn from the experimental programme. In addition, the potential of the new earth mixture with regards to its usability in the field of building construction and architectural design is further elaborated on. The method used in this study is the first of its kind that allows investors to avoid the very time-consuming processes such as finding a suitable source for soil excavation and soil classification. The developed mixture has significant workability and suitability for production of stabilized earthen panels — the very first of its kind. Such a panel is practically feasible, reasonable, and could be integrated into earthen building standards in general and in particular to DIN 18948, which is related to earthen boards and published in 2018. KW - Lehm KW - Stabilisierung KW - Lehmbau KW - Kalk KW - Gips Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220803-46989 ER - TY - JOUR A1 - Arnold, Robert A1 - Kraus, Matthias ED - Pham, Duc T1 - On the nonstationary identification of climate-influenced loads for the semi-probabilistic approach using measured and projected data JF - Cogent Engineering N2 - A safe and economic structural design based on the semi-probabilistic concept requires statistically representative safety elements, such as characteristic values, design values, and partial safety factors. Regarding climate loads, the safety levels of current design codes strongly reflect experiences based on former measurements and investigations assuming stationary conditions, i.e. involving constant frequencies and intensities. However, due to climate change, occurrence of corresponding extreme weather events is expected to alter in the future influencing the reliability and safety of structures and their components. Based on established approaches, a systematically refined data-driven methodology for the determination of design parameters considering nonstationarity as well as standardized targets of structural reliability or safety, respectively, is therefore proposed. The presented procedure picks up fundamentals of European standardization and extends them with respect to nonstationarity by applying a shifting time window method. Taking projected snow loads into account, the application of the method is exemplarily demonstrated and various influencing parameters are discussed. KW - Reliabilität KW - Extreme value distribution KW - climate loads KW - nonstationarity KW - semi-probabilistic concept KW - First Order Reliability Method KW - OA-Publikationsfonds2022 Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20221117-47363 UR - https://doi.org/10.1080/23311916.2022.2143061 VL - 2022 IS - Volume 9, issue 1, article 2143061 SP - 1 EP - 26 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Taraben, Jakob A1 - Morgenthal, Guido T1 - Integration and Comparison Methods for Multitemporal Image-Based 2D Annotations in Linked 3D Building Documentation JF - Remote Sensing N2 - Data acquisition systems and methods to capture high-resolution images or reconstruct 3D point clouds of existing structures are an effective way to document their as-is condition. These methods enable a detailed analysis of building surfaces, providing precise 3D representations. However, for the condition assessment and documentation, damages are mainly annotated in 2D representations, such as images, orthophotos, or technical drawings, which do not allow for the application of a 3D workflow or automated comparisons of multitemporal datasets. In the available software for building heritage data management and analysis, a wide range of annotation and evaluation functions are available, but they also lack integrated post-processing methods and systematic workflows. The article presents novel methods developed to facilitate such automated 3D workflows and validates them on a small historic church building in Thuringia, Germany. Post-processing steps using photogrammetric 3D reconstruction data along with imagery were implemented, which show the possibilities of integrating 2D annotations into 3D documentations. Further, the application of voxel-based methods on the dataset enables the evaluation of geometrical changes of multitemporal annotations in different states and the assignment to elements of scans or building models. The proposed workflow also highlights the potential of these methods for condition assessment and planning of restoration work, as well as the possibility to represent the analysis results in standardised building model formats. KW - Bauwesen KW - Punktwolke KW - Denkmalpflege KW - OA-Publikationsfonds2022 Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220513-46488 UR - https://www.mdpi.com/2072-4292/14/9/2286 VL - 2022 IS - Volume 14, issue 9, article 2286 SP - 1 EP - 20 PB - MDPI CY - Basel ER - TY - JOUR A1 - Chowdhury, Sharmistha A1 - Zabel, Volkmar T1 - Influence of loading sequence on wind induced fatigue assessment of bolts in TV-tower connection block JF - Results in Engineering N2 - Bolted connections are widely employed in structures like transmission poles, wind turbines, and television (TV) towers. The behaviour of bolted connections is often complex and plays a significant role in the overall dynamic characteristics of the structure. The goal of this work is to conduct a fatigue lifecycle assessment of such a bolted connection block of a 193 m tall TV tower, for which 205 days of real measurement data have been obtained from the installed monitoring devices. Based on the recorded data, the best-fit stochastic wind distribution for 50 years, the decisive wind action, and the locations to carry out the fatigue analysis have been decided. A 3D beam model of the entire tower is developed to extract the nodal forces corresponding to the connection block location under various mean wind speeds, which is later coupled with a detailed complex finite element model of the connection block, with over three million degrees of freedom, for acquiring stress histories on some pre-selected bolts. The random stress histories are analysed using the rainflow counting algorithm (RCA) and the damage is estimated using Palmgren-Miner's damage accumulation law. A modification is proposed to integrate the loading sequence effect into the RCA, which otherwise is ignored, and the differences between the two RCAs are investigated in terms of the accumulated damage. KW - Schadensakkumulation KW - Lebenszyklus KW - Fatigue life KW - Damage accumulation KW - Wind load KW - Rainflow counting algorithm KW - Loading sequence KW - Windlast KW - OA-Publikationsfonds2022 Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20221028-47303 UR - https://www.sciencedirect.com/science/article/pii/S2590123022002730?via%3Dihub VL - 2022 IS - Volume 16, article 100603 SP - 1 EP - 18 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Hoinkis, Jule Hannah T1 - Hitze in der Stadt Jena BT - Eine Untersuchung des städtischen Mikroklimas von Jena, dessen Veränderungen infolge des Klimawandels, städtebaulicher Anpassungsstrategien & Anwendung der Ergebnisse anhand eines städtebaulichen Konzeptes zur Neugestaltung des Bachstraßenareals. N2 - Die vorliegende Arbeit befasst sich mit den spezifischen Faktoren und Wechselwirkungen des städtischen Klimas und Strategien zur Prävention und Kompensation lokaler Klimaveränderungen. Problematische Merkmale des Stadtklimas werden sich infolge des Klimawandels stärker ausprägen. Insbesondere die Hitzebelastung wird zunehmen und die Lebensbedingungen in der Stadt negativ beeinflussen. Infolge höherer Temperaturen in Städten und einer höheren Temperaturdifferenz zum Umland verändern sich Windströme und die Wasserbilanz. Es sind Strategien notwendig, um den Schadstoffausstoß, die Flächeninanspruchnahme, die Abfallproduktion und den Wasser-, Energie- und Ressourcenverbrauch zu verringern, um sowohl langfristig den Klimawandel als auch dessen bereits unvermeidbaren Auswirkungen auf Städte zu begrenzen. Beispielhaft untersucht die Arbeit das Stadtklima, dessen zukünftige Veränderungen infolge des Klimawandels, bauliche Maßnahmen und Anpassungsstrategien der Stadt Jena. Jena ist die zweitgrößte Stadt im Bundesland Thüringen und gehört heute zu den wärmsten und trockensten Großstädten Deutschlands. Die Ergebnisse der Arbeit werden anschließend anhand eines städtebaulichen Konzepts und Entwurfs angewendet. Das Bachstraßenareal liegt in der Innenstadt, dem am stärksten von Hitze betroffenen Stadtteil. Als ehemaliger Hauptstandort des Jenaer Universitätsklinikums, soll es zu einem nachhaltigen Wissenschaftscampus der Lebenswissenschaften umgebaut werden, wobei ein Großteil der denkmalgeschützten, ehemaligen Klinikgebäude erhalten bleibt. Der Fokus liegt dabei auf der Umsetzung der zuvor formulierten, nachhaltigen Strategien zur Verbesserung des lokalen Stadtklimas und einer Abschwächung der Auswirkungen des Klimawandels auf den besonders stark betroffenen Innenstadtbereich Jenas. KW - Hitze KW - Jena KW - Stadtklima KW - Klimawandel Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220414-46323 ER - TY - THES A1 - Habtemariam, Abinet Kifle T1 - Generalized Beam Theory for the analysis of thin-walled circular pipe members N2 - The detailed structural analysis of thin-walled circular pipe members often requires the use of a shell or solid-based finite element method. Although these methods provide a very good approximation of the deformations, they require a higher degree of discretization which causes high computational costs. On the other hand, the analysis of thin-walled circular pipe members based on classical beam theories is easy to implement and needs much less computation time, however, they are limited in their ability to approximate the deformations as they cannot consider the deformation of the cross-section. This dissertation focuses on the study of the Generalized Beam Theory (GBT) which is both accurate and efficient in analyzing thin-walled members. This theory is based on the separation of variables in which the displacement field is expressed as a combination of predetermined deformation modes related to the cross-section, and unknown amplitude functions defined on the beam's longitudinal axis. Although the GBT was initially developed for long straight members, through the consideration of complementary deformation modes, which amend the null transverse and shear membrane strain assumptions of the classical GBT, problems involving short members, pipe bends, and geometrical nonlinearity can also be analyzed using GBT. In this dissertation, the GBT formulation for the analysis of these problems is developed and the application and capabilities of the method are illustrated using several numerical examples. Furthermore, the displacement and stress field results of these examples are verified using an equivalent refined shell-based finite element model. The developed static and dynamic GBT formulations for curved thin-walled circular pipes are based on the linear kinematic description of the curved shell theory. In these formulations, the complex problem in pipe bends due to the strong coupling effect of the longitudinal bending, warping and the cross-sectional ovalization is handled precisely through the derivation of the coupling tensors between the considered GBT deformation modes. Similarly, the geometrically nonlinear GBT analysis is formulated for thin-walled circular pipes based on the nonlinear membrane kinematic equations. Here, the initial linear and quadratic stress and displacement tangent stiffness matrices are built using the third and fourth-order GBT deformation mode coupling tensors. Longitudinally, the formulation of the coupled GBT element stiffness and mass matrices are presented using a beam-based finite element formulation. Furthermore, the formulated GBT elements are tested for shear and membrane locking problems and the limitations of the formulations regarding the membrane locking problem are discussed. N2 - Eine detaillierte Strukturanalyse dünnwandiger, kreisförmiger Rohrelemente erfordert oft die Verwendung von Schalenelementen in der Finite Elemente Methode. Diese Methode ermöglicht eine sehr gute Approximation des Verformungszustandes, erfordert jedoch einen hohen Grad der Diskretisierung, welcher wiederum einen hohen Rechenaufwand verursacht. Eine alternative Methode hierzu basiert auf klassischen Balkentheorien, welche eine einfache Modellierung ermöglichen und wesentlich geringeren Rechenaufwand erfordern. Diese weisen jedoch Einschränkungen bei der Approximation von Verformungen auf, da Querschnittsverformungen nicht berücksichtigt werden können. Schwerpunkt dieser Dissertation ist eine Untersuchung der Verallgemeinerten Technischen Biegetheorie (VTB), die sowohl eine genaue als auch eine effiziente Analyse von dünnwandigen Tragwerkselementen ermöglicht. Diese Theorie basiert auf einer Trennung der Variablen, in der das Verschiebungsfeld als eine Kombination von vorbestimmten Verformungsmoden der Querschnitts und unbekannten Amplitudenfunktionen in Längsrichtung ausgedrückt wird. Obwohl die VTB ursprünglich für lange, gerade Elemente entwickelt wurde, können durch die Berücksichtigung komplementärer Verformungsmoden, welche die Null-Annahmen der klassischen VTB für Quer- und Schubmembrandehnung abändern, Probleme mit kurzen Elementen, Rohrbögen und geometrischer Nichtlinearität analysiert werden. In dieser Dissertation wird die VTB-Formulierung für die Analyse dieser Probleme entwickelt. Die Anwendung und Möglichkeiten der Methode werden anhand mehrerer numerischer Beispiele veranschaulicht, deren Verschiebungs- und Spannungsfeldanalysen anhand eines äquivalenten, verfeinerten, schalenbasierten Finite-Elemente-Modells verifiziert werden. Die entwickelten statischen und dynamischen VTB-Formulierungen für Rohrbogenelemente basieren auf der linearen kinematischen Beschreibung der Theorie gekrümmter Schalen. In diesen Formulierungen wird das komplexe Problem in Rohrbögen aufgrund des starken Kopplungseffekts der Längsbiegung, der Verwölbung und der Querschnittsovalisierung durch die Herleitung der Kopplungstensoren zwischen den betrachteten VTB-Verformungsmoden präzise behandelt. In ähnlicher Weise wird die geometrisch nichtlineare VTB-Analyse für gerade Rohrelemente auf der Grundlage der nichtlinearen kinematischen Membrangleichungen formuliert. Die anfänglichen linearen und quadratischen Spannungs- und Verschiebungs-Tangentensteifigkeitsmatrizen werden dabei unter Verwendung der VTB-Kopplungstensoren dritter und vierter Ordnung aufgebaut. In Längsrichtung wird die Formulierung der gekoppelten VTB-Element-Steifigkeits- und Massenmatrizen unter Verwendung einer balkenbasierten Finite-Elemente Formulierung dargestellt. Weiterhin werden die VTB-Elemente auf Schub- und Membran-Locking-Probleme getestet und die Einschränkungen der Formulierungen bezüglich des Membran-Locking-Problems diskutiert. T3 - ISM-Bericht // Institut für Strukturmechanik, Bauhaus-Universität Weimar - 2022,2 KW - Finite-Elemente-Methode KW - Dynamische Analyse KW - Generalized Beam Theory (GBT) KW - Finite Element Method KW - Dynamic Analysis KW - Geometrically nonlinear analysis KW - Curved thin-walled circular pipes Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220127-45723 ER - TY - JOUR A1 - Kumari, Vandana A1 - Harirchian, Ehsan A1 - Lahmer, Tom A1 - Rasulzade, Shahla T1 - Evaluation of Machine Learning and Web-Based Process for Damage Score Estimation of Existing Buildings JF - Buildings N2 - The seismic vulnerability assessment of existing reinforced concrete (RC) buildings is a significant source of disaster mitigation plans and rescue services. Different countries evolved various Rapid Visual Screening (RVS) techniques and methodologies to deal with the devastating consequences of earthquakes on the structural characteristics of buildings and human casualties. Artificial intelligence (AI) methods, such as machine learning (ML) algorithm-based methods, are increasingly used in various scientific and technical applications. The investigation toward using these techniques in civil engineering applications has shown encouraging results and reduced human intervention, including uncertainties and biased judgment. In this study, several known non-parametric algorithms are investigated toward RVS using a dataset employing different earthquakes. Moreover, the methodology encourages the possibility of examining the buildings’ vulnerability based on the factors related to the buildings’ importance and exposure. In addition, a web-based application built on Django is introduced. The interface is designed with the idea to ease the seismic vulnerability investigation in real-time. The concept was validated using two case studies, and the achieved results showed the proposed approach’s potential efficiency KW - Maschinelles Lernen KW - rapid assessment KW - Machine learning KW - Vulnerability assessment KW - OA-Publikationsfonds2022 Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:wim2-20220509-46387 UR - https://www.mdpi.com/2075-5309/12/5/578 VL - 2022 IS - Volume 12, issue 5, article 578 SP - 1 EP - 23 PB - MDPI CY - Basel ER -